★ Jared Lyall enters the vehicle, pulling a button from inside the car as to open up the vehicle's hood.
★ Jared Lyall opens up the door, then heads outside and walks towards the front of the vehicle - opening
★ - up the hood then he heads under it and supports it with the stands.      ((Jared Lyall))
★ Jared Lyall heads for two boxes near the vehicle - one being a toolbox and the other is a
★ bolt organizer box.      ((Jared Lyall))
★ Jared Lyall puts both of the boxes onto the ground near the hood, then heads into the toolbox and
★ grabs a socket and a rachet, then untightens the nuts on the battery's negative      ((Jared Lyall))
★ - terminal.      ((Jared Lyall))
★ Jared Lyall then to remove the cable, then repeats the same actions for the battery's -
★ - positive terminal.      ((Jared Lyall))
★ Jared Lyall heads for the battery's handle, then pulls it upwards, putting it carefully next to him -
★ - on the ground.      ((Jared Lyall))
★ Jared Lyall puts back the socket and wrench into the toolbox, and heads into his pocket for the -
★ - vehicle keys.      ((Jared Lyall))
★ Jared Lyall opens up the vehicle trunk, and heads for a couple of hydraulic jacks.
★ Jared Lyall puts them under the vehicle. He starts pressing each jack after -
★ - securely tightening the jack under different axle parts. Jared ensures they're -      ((Jared Lyall))
★ - placed on spots that do not threaten the axle's integrity, so he'd place them next to -      ((Jared Lyall))
★ - a beam axle, but not on it as not to damage it.      ((Jared Lyall))
★ Jared Lyall heads for two medium-sized containers, he grabs them then heads back -
★ - to the vehicle.      ((Jared Lyall))
★ Jared Lyall puts one under the coolant and another one under the engine oil valve; proceeding to -
★ - unscrew the valves as to drain both of them into the containers.      ((Jared Lyall))
★ There would be a good amount of glitter in the oil due to the high vehicle mileage.      ((Jared Lyall))
★ Jared Lyall puts away the containers from under the vehicle after the valves have been -
★ - completely drained.      ((Jared Lyall))
★ Jared Lyall starts lowering the vehicle once more.
★ Jared Lyall then to unplug a coolant line from the radiator to the transmission coolant -
★ then heads into the toolbox quickly and plugs it into the line to prevent leaking the      ((Jared Lyall))
★ fluid everywhere.      ((Jared Lyall))
★ Jared Lyall heads for a 45 degrees plier and a 90 degrees plier - using both to reach into the hose
★ clamps and removes the second line.      ((Jared Lyall))
★ Jared Lyall puts back the clamps into the toolbox and heads into it again for a socket and -
★ - a wrench, removing the bolts holding down the radiator then putting the bolts down -      ((Jared Lyall))
★ - onto the ground next to him, next to the wall.      ((Jared Lyall))
★ Jared Lyall puts down the socket and ratchet next to the bolts.
★ Jared Lyall removes the radiator entirely from the vehicle and puts it next to the battery.
★ Jared Lyall leans up the radiator against the wall.
★ Jared Lyall heads into the vehicle, he aims for the throttle cable, rolling it backwards and then -
★ - slips the cable out.      ((Jared Lyall))
★ Jared Lyall heads into the toolbox and grabs the ratchet and socket, removing the -
★ - bolts that hold the cable into the intake, then puts the bolts into the holder's second      ((Jared Lyall))
★ - slot.      ((Jared Lyall))
★ Jared Lyall pushes the intake out of the way.
★ Jared Lyall lowers the hood, then puts his hands under it; looking for the bolts carefully -
★ - as not to scratch the fenders, then unscrews them.      ((Jared Lyall))
★ Jared Lyall removes the hood entirely from its position.
★ Jared Lyall puts it hood against the wall.
★ Jared Lyall unbolts the airbox using the socket and ratchet, then removes it and puts it against the -
★ - wall as well.      ((Jared Lyall))
★ Jared Lyall removes the wiring harness between the runners and the intake manifold.
★ Jared Lyall turns his head towards the air compressor - disconnecting it and disconnecting the -
★ - power steering pump.      ((Jared Lyall))
★ Jared Lyall heads for the three bolts on the power assembly - the bolts being of different sizes -
★ two being 15mm, one being 17mm (06 charger specs).      ((Jared Lyall))
★ Jared Lyall then to use the appropriate sockets, removing the three bolts and putting them near -
★ - the wall.      ((Jared Lyall))
★ Jared Lyall removes the pump from the engine and pushes it away.
★ There would be some clearance between the harmonic balancer and the fender.      ((Jared Lyall))
★ Jared Lyall heads for the impact gun in the toolbox, then then to remove the bolts holding -
★ the harmonic balancer into place.      ((Jared Lyall))
★ Jared Lyall pulls out the harmonic balancer and puts it next to the vehicle parts near the wall.
★ Jared Lyall heads for the exhaust pipe - disconnecting the bolts holding it with the impact gun.
★ Jared Lyall puts back the impact gun into the toolbox, then heads for another hydro-jack.
   Please try not to spam too much or you will have your commands disabled.
★ Jared Lyall puts the hydro-jack under the transmission pan to push the pan up, then pulls it out.
★ The cover hiding the driver plate would be in plain sight now.      ((Jared Lyall))
★ Jared Lyall pulls up the plastic cover and puts it next to the car parts near the wall.
★ Jared Lyall turns his head again to the now obvious torque converter, which was hidden by -
★ - the plastic cover.      ((Jared Lyall))
★ Jared Lyall grabs a socket with a ratchet as he starts to loosen up the spark plugs.
★ Jared Lyall puts the socket and ratchet onto the bolts on the crank shaft and loosens them up -
★ - from the torque converter, moving the converter with his other hand as he rotates it and -      ((Jared Lyall))
★ - removes the bolts from it accordingly.      ((Jared Lyall))
★ Jared Lyall heads for the engine to transmission bolts as he starts loosening them up.
★ Jared Lyall removes the second grade 8 bolt underneath the cover entirely.
★ Jared Lyall heads for another jack and a small block of wood.
★ Jared Lyall adjusts the block of wood onto the jack, and pushes it under the oil pan as to -
★ - get clearance on the engine bolts to unscrew and remove them.      ((Jared Lyall))
★ Jared Lyall then to remove the bolts and nut set from the first engine mount.
★ Jared Lyall removes the bolts from the second engine mount, near the fender.
★ Jared Lyall removes the final engine to transmission bolt which has been loosened earlier.
★ A gap would form between the engine and transmission.      ((Jared Lyall))
★ Jared Lyall heads for a crane, he ties the crane's chains to the intake runners, from the -
★ - fender's side.      ((Jared Lyall))
★ Jared Lyall ties the chain around the exhaust manifold runners around the engine as well.
★ Jared Lyall hooks up the chain to the crane, ensuring nothing's bound up by the chain.
★ Jared Lyall double checks that nothing is still connected to the engine before heading -
★ - towards the crane.      ((Jared Lyall))
★ Jared Lyall jacks up the crane until the tension starts to build on the chain.
★ Jared Lyall ensures again than nothing is binding by heading towards the engine himself -
★ - after the tension's been built and moving the engine a bit - also separating it      ((Jared Lyall))
★ - farther off from the transmission.      ((Jared Lyall))
★ Jared Lyall heads for a pry bar, then pushes it between the engine and transmission carefully.
★ Jared Lyall slowly separates them a bit further just to get enough leeway.
★ Jared Lyall pumps up the crane again.
★ The driver plate would be entirely visible.      ((Jared Lyall))
★ Jared Lyall cranks up the engine completely from the  vehicle, then carefully pushes the crane -
★ - away after ensuring the engine has enough leverage.      ((Jared Lyall))
★ The engine would now be completely removed from the vehicle.      ((Jared Lyall))
★ Jared Lyall grabs a 2mm socket and a wrench, then beings to twist the bumper's bolt counter -
★ -clockwise.      ((Jared Lyall))
★ The radiator is already removed along with everything in the engine bay.      ((Jared Lyall))
★ The bumpers are now removed.      ((Jared Lyall))
★ Jared Lyall heads for the hydro-jack, then heads over to the front-side wheel.
★ Jared Lyall lifts the vehicle, he then heads for a socket and ratchet.
★ Jared Lyall starts removing the nuts on the wheel, then removes the rim.
★ After removing the nuts holding the rum, Jared removes the nuts holding the wheel.      ((Jared Lyall))
★ Jared Lyall removes the wheel in its entirety, putting it next to the other vehicle parts along the wall.
★ Jared Lyall heads for another hydro-jack, then heads for the other front-side wheel.
★ Jared Lyall lifts the vehicle, repeating the process.
★ Jared Lyall heads for a socket and ratchet, removes the rim, then removes the wheel.
★ Jared Lyall puts the wheel next to the other wheels along the wall.
★ Jared Lyall repeats the process with the other two wheels.
★ Jared Lyall grabs a 9mm spanner and applies it to the brake hose, twisting it counterclockwise -
★ - to release the bolt.      ((Jared Lyall))
★ Jared Lyall applies the spanner to both bolts sequentially in order to remove them, then pops out
★ - the brake pads.      ((Jared Lyall))
★ Jared Lyall puts the brake caliper near the wall.
★ Jared Lyall repeats the process for the other brakes.
★ Jared Lyall heads for a hydro-jack.
★ Jared Lyall puts the jack next to him, then heads forward for the rubber cover in the driver's door,
★ pulling it until a screw is revealed.      ((Jared Lyall))
★ Jared Lyall heads for a screwdriver and unscrews it.
★ An electric connector is revealed.      ((Jared Lyall))
★ Jared Lyall pulls the connector apart, depressing the tab and separating the door until the door is half
★ removed from the car body.      ((Jared Lyall))
★ Jared Lyall unbolts the hinges entirely, then slowly puts his left hand under the door as the hinges -
★ - fall off, then holds the door and rests it up against the wall.      ((Jared Lyall))
★ Jared Lyall repeats the process with the other three doors.
★ Jared Lyall heads for the front of the vehicle.
★ Jared Lyall looks over as he inspects the front-lights.
★ Jared Lyall heads into the engine bay, he starts unwiring the front-lights.
★ Jared Lyall heads for a socket and ratchet as he starts unbolting the nuts attached in the -
★ - engine bay that hold the lights in place.      ((Jared Lyall))
★ Jared Lyall removes the front-left car headlight.
★ Jared Lyall looks over at the other headlight.
★ Jared Lyall heads into the engine bay, he unwires the other light.
★ Jared Lyall heads for the same socket and ratchet.
★ Jared Lyall starts unbolting the nuts attached to the second light.
★ Jared Lyall removes the second headlight.
★ Jared Lyall puts both headlights against the wall, next to the other vehicle parts.
★ Jared Lyall slowly walks to the back-end of the vehicle.
★ Jared Lyall opens up the trunk, then starts removing the nuts holding the trunk in place using -
★ - the socket and ratchet, then slowly removes the trunk entirely and puts it next -      ((Jared Lyall))
★ - to the other vehicle parts against the wall.      ((Jared Lyall))
★ Jared Lyall removes the trunk dressing, now the wiring and nuts holding the backlights are -
★ - visible.      ((Jared Lyall))
★ Jared Lyall heads for the socket and ratchet.
★ Jared Lyall starts unbolting the nuts holding the backlights in place.
★ Jared Lyall does this for the left brake light first.
★ Jared Lyall removes the brakelight after disconnecting it, then puts it against the wall.
★ Jared Lyall heads towards the second brakelight.
★ Jared Lyall starts unbolting it.
★ Jared Lyall removes the backlight and puts it next to the other one.
★ Jared Lyall heads inside the vehicle, he readjusts the seat as he starts removing the screws holding the -
★ - front driver's seat.      ((Jared Lyall))
★ Jared Lyall ensures nothing's holding down the driver seat then removes it from the vehicle.
★ Jared Lyall repeats the process for the passenger side seat.
★ Jared Lyall puts both seats against the wall.