SHARE
TWEET

SC220

a guest Feb 16th, 2020 93 Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. FullCase.Slot0.101.86 >_devils
  2. _boot          Download the boot image (FW image 1 and 2 erased)
  3. _cliAddTrc     Add Trace to HALI Log - [Trace Param Val]
  4. _cliClear      Clear HALI Trace Log
  5. _cliMask       Display/Set Trace Mask - ([hali|sce|fwcore] [mask value]) (y|n)
  6. _clises        Display CLI over SES debug information
  7. _cliTime       Add Time Trace Entry to HALI Log - [on|off]
  8. _cliTrcSev     Change HALI Trace Log Severity - [Trace Severity]
  9. _cliTrcShow    Show HALI Trace Log
  10. _clrphyerr     Clear PHY error counter(s) <phy Num (invalid PHY Num=all)>
  11. _date          Date: date
  12. _debugpage2    Dispalys Page 2 data when Host read it : 0 = OFF !0 = Active
  13. _devils        Print the Extended help
  14. _dwd_reset     Disable WatchDog reset: dwd_reset
  15. _download      Down load code using Xmodem: Region[0-9] Offset Erase[y/n]
  16. _download_fpga Down FPGA load code using Xmodem: _download_fpga
  17. _drive_pres    Return Drive presense: _drive_pres
  18. _ecc           Display ECC counts: ecc {clear}
  19. _ema_poll      Turns on or off the analysis polling.  Disables SES & LED update
  20. _epd           Shut down external PHYs
  21. _epu           Bring up external PHYs
  22. _erase         Erase F/W Region: erase [0..10] NOTE: This can mess up your code!
  23. _event         Event log test
  24. _fan_ctrl_thrd Write fan control parameters in C: fan_ctrl_thrd <M> <H> <SIM offset> <hysteresis>
  25. _flashdump     Dump Flash: flashdump <offset> <length>
  26. _fpgaread      Read FPGA Register: fpgaread <register> <length>
  27. _fpgawrite     Write FPGA Register: fpgawrite <register> <data> [<register> <data>...]
  28. _fail_ts       Fail temperature sensor: fail_ts <sensor>
  29. _flashpeer     Flash Peer: <0=ACTIVE ; 1=BOOT>
  30. _gpio_setting  Read a GPIO Setting: gpio_settings <0..7>
  31. _history       Show CLI History: history
  32. _hotswap       Enable/disable Hotswap
  33. _icid_clear    Clears the ICID value to default.
  34. _isim_msg      Send message to ISIM thread
  35. _ledconfig     Show LED Configuration Settings
  36. _ledmode       Set Mode for led: ledmode <number><direction><state>
  37. _ledread       Read LED GPIO value: ledread <number>
  38. _ledset        Set LED GPIO Value: ledset <number><state>
  39. _lm75_trip     LM75 Interrrupt Control: lm75_trip <sensor><state>
  40. _loadcpld      Load xsvf file from flash into CPLD
  41. _map           Display SES Sensor Data: map
  42. _phyerr        Display Phy Errors for all phys
  43. _phyinfo       Display Phy Info
  44. _ps_pmb_test   Test P/S Module PMBUS commands: ps_pmb_test <l(eft)/r(ight)>
  45. _psfup         P/S Module Firmware update: psfup <l(eft)/r(ight)>
  46. _queue         Dump the Message Queue usage: queue
  47. _quick         Quick regression: quick
  48. _rdcam         Read CAM Address contents <address (0-1024)>, <display count>
  49. _rdtxphy       Display current SASTX2G Phy settings <phy Num (invalid PHY Num=all)>
  50. _rdrxphy       Display current SASRX2G Phy settings <phy Num (invalid PHY Num=all)>
  51. _rdphyerr      Display PHY error counters <phy Num (invalid PHY Num=all)>
  52. _rdled         LED Control Register Read: rdled  <offset> <# of 32 bit words>
  53. _readcfg       Read config page <Page ID> [<Region>]
  54. _routetable    Display Routing Tables: routetable
  55. _runtime       Down load code using Xmodem to the non-active region: runtime
  56. _scsilog       Display SCSI Event Log information: (<eventToDisplay>)
  57. _selfdisc      Display expander's self discovery status descriptors
  58. _set_cid       Set company ID of ELI: cid_set [0-From Exp, 1-Custom <32bit data>]
  59. _shutdown      Invoke a thermal shut down sequence: _shutdown <why>
  60. _shutup        Slow down fans: _shutup <0-100%> 20 default
  61. _slotiso       Dump Slot Isolation Debug Data
  62. _slotled       Control Slot LEDs: slotled <slot><pattern> (slot > MaxDrive = 'all')
  63. _splitforce    Control Split Override: splitforce <0-switched; 1-ForceJoin; 3-ForceSplit>
  64. _ssc_control   Turn SSC on or off <enable 1, disable 0>
  65. _ssptDebug     Dump SSP Target Debug info
  66. _stack         Show Stack Usage: stack
  67. _temp_thrd     Write temp thresholds: temp_thrd <HS> <HC> <HW> <LW> <LC> <LS>
  68. _test_fail     Test Failover on the alternate controller
  69. _test_stub     test_stub
  70. _thread        Display Threadx Information: thread
  71. _timer         Display Timer information: timer
  72. _trace         Display Trace Log [- for Tail] [+ for Head]: trace [-]count
  73. _traceclear    Clear trace log: traceclear
  74. _twi_hang      Hang the TWI bus for testing purposes only
  75. _ver           Version Information: ver
  76. _wdt           WatchDog test: wdt <who>
  77. _who           Who's home (installed): who
  78. _wrphy         Write SAS2G1-3 Phy setting <phy number,Dword>
  79. _wrphyall      Write all SAS2G1-3 Phy setting <uses PHY setting table>
  80. _zone_mask     Display Zone Mask for all PHYs
  81.  
  82. FullCase.Slot0.101.88 >devils
  83. asset_tag   Set or Display the Asset Tag: asset_tag {setvalue}
  84. broadcast   Send Broadcast SES Message: broadcast
  85. chassisname Display and or Set Chassis Name: chassisname <name string}
  86. chassistype Display and or Set Chassis Type: chassistype <0 = Blue Devil !0 = Red Devil>
  87. clear_eel   Clear Event Error Log: clear_eel
  88. clear_temp  Remove override of Temperature: clear_temp <sensor>
  89. dbs         Database Read  : dbs  <page>
  90. devils      Print the Help Screen
  91. drive_led   Write drive led: <logicaldrive> <data>
  92. eepromdump  EEprom Dump: eepromdump <port><addr><size in K(1,2,4,8,..512>
  93. eepromfill  EEprom Fill: eepromfill <port><addr><size in K(1,2,4,8,..512><pattern>
  94. eepromwrite EEprom Write: eepromwrite <port><addr><size in K(1,2,4,8,..512><offset><length><pattern>
  95. fanlog      Fan fault count for each power supply fan [8 per unit]
  96. fpgadisable Put FPGA in Slave Mode: fpgadisable>
  97. fpgaenable  Put FPGA in Master Mode: fpgaenable>
  98. fpga_rd     FPGA Access: fpga_rd <Register> <#bytes>
  99. fpga_wr     FPGA Access: fpga_wr <Register> <data>[<Register> <data> ...]
  100. fru_display Display FRU Status: fru_display
  101. fru_clear   Clear Fru: fru_clear [0-SIM0, 1-SIM1, 2-PBP, 3-PS0, 4-PS1 5-SBP]
  102. fru_download Download Fru: fru_download [0-SIM0, 1-SIM1, 2-PBP, 3-PS0, 4-PS1 5-SBP]
  103. fru_read    Read Fru: fru_read [0-SIM0, 1-SIM1, 2-PBP, 3-PS0, 4-PS1 5-SBP]]
  104. get_time    get encl time: get_time
  105. gpio_rd     Read a GPIO: gpio_rd <number>
  106. heart_beat  SIM Heartbeat Control: heart_beat [0=off !0=on] <timeout>
  107. isim_debug  Change or view isim stats: <data> <0 - Disable; 1 - Enable>
  108. l4_test     L4 integration manufacturing diag: l4_test
  109. lm75        LM75 Read Access: lm75 <Slave Address>
  110. lm75_rd     LM75 Read Access: lm75_rd <Slave Address> <Register>
  111. lm75_wr     LM75 Write Access: lm75_wr <Slave Address> <Register> <1 byte>
  112. log_ipmi    Log an IPMI Event:log_ipmi<Code><Type><Sensor><EV0><EV1><EV2><EV3>
  113. max6654     Display MAX6654 Registers: max6654 <i2c port><slave addr>
  114. noise       Write audible alarm: <data>
  115. nvramread8  Read NVram 32bit area: nvramread <address> <length>
  116. nvramread   Read NVram 32bit area: nvramread <32bit address> <length>
  117. nvramwrite8 Write NVram 32bit area: nvramwrite <address> <data> [<32bit address> <data> ...]
  118. nvramwrite  Write NVram 32bit area: nvramwrite <32bit address> <data> [<32bit address> <data> ...]
  119. page_a      Display drive SAS Address: page_a
  120. ps_status   Get P/S Module Status: ps_status <l(eft)/r(ight)>
  121. ps_cap      Get P/S Module capability: ps_cap <l(eft)/r(ight)>
  122. ps_clear    Clear P/S Module Status: ps_clr <l(eft)/r(ight)>
  123. ps_page     Get P/S Module Status: ps_status <l(eft)/r(ight)>
  124. ppid        Set or Display PPID: ppid {fruNumber}{setvalue}
  125. prompt      Prompt on/off
  126. rd_8        8-bit Read: rd_8   <address> <# of 8 bit words>
  127. rd_16       16-bit Read: rd_16  <address> <# of 16 bit words>
  128. rd_32       32-bit Read: rd_32  <address> <# of 32 bit words>
  129. reset_peer  Reset other SIM using GPIO <1-reset peer>
  130. reset       Reset ARM using Watch Dog timer
  131. rev         SIM Firmware and Diagnogstic Revision
  132. sas_address Display SAS Address from Phys: (option for magic addr <1>)
  133. sbb_status  Set SBB status: sbb_set <default-print status, 0-set good, 1-set failed>
  134. scratchpad  Display Location of Memory Test Area: scratchpad
  135. service_tag Set or Display the Service Tag: service_tag {setvalue}
  136. ses_page    Display SES Page: ses_page <page><buffer size>
  137. set_speed   Sets Fan Speeds: set_speed <0-100%> 20 default
  138. set_temp    set encl temp: set_temp <sensor><temp>( -55 to 125 degrees C)
  139. set_thres   Set P/S Module Fan Speed Threshold: set_thres <l(eft)/r(ight)><speed code 0..15>
  140. shelf_led   Write shelf led: <data> <0 - Disable; 1 - Enable>
  141. twi_dis     TWI device discovery: twi_dis
  142. twi_rd      TWI device byte read: twi_rd <port ID> <address> <# of bytes - 0xff max>
  143. twi_stats   Dump twi statistics: twi_stats [clear]
  144. twi_wr      TWI device byte write: twi_wr <port ID> <address> {0xff bytes max}
  145. twi_wr_rd   TWI device wr/rd: twi_wr_rd <port ID> <address> <#read bytes> <write data>
  146. wr_8        8-bit Write: wr_8  <address> <data> [<address> <data> ...]
  147. wr_16       16-bit Write: wr_16 <address> <data> [<address> <data> ...]
  148. wr_32       32-bit Write: wr_32 <address> <data> [<address> <data> ...]
RAW Paste Data
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy. OK, I Understand
Top