4

smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.1.106-Unraid] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUH721010AL4200
Revision:             A923
Compliance:           SPC-4
User Capacity:        10,000,831,348,736 bytes [10.0 TB]
Logical block size:   512 bytes
Physical block size:  4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca25110991c
Serial number:        7PG93ZBG
Device type:          disk
Transport protocol:   SAS (SPL-4)
Local Time is:        Fri Mar 28 13:09:50 2025 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Grown defects during certification = 0
Total blocks reassigned during format = 0
Total new blocks reassigned = 0
Power on minutes since format = 18585
Current Drive Temperature:     50 C
Drive Trip Temperature:        85 C

Manufactured in week 28 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  41
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  2478
Elements in grown defect list: 0

Vendor (Seagate Cache) information
  Blocks sent to initiator = 3024585326854144

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0     3665         0      3665   37697228    2019079.160           0
write:         0        0         0         0     395590     387020.141           0
verify:        0        0         0         0      25590          0.000           0

Non-medium error count:        0

SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -   57380                 - [-   -    -]

Long (extended) Self-test duration: 69240 seconds [19.2 hours]

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 57380:07 [3442807 minutes]
    Number of background scans performed: 39,  scan progress: 6.92%
    Number of background medium scans performed: 39

General statistics and performance log page:
  General access statistics and performance:
    Number of read commands: 1358438567
    Number of write commands: 180279334
    number of logical blocks received: 755898712168
    number of logical blocks transmitted: 3943513983683
    read command processing intervals: 0
    write command processing intervals: 0
    weighted number of read commands plus write commands: 0
    weighted read command processing plus write command processing: 0
  Idle time:
    Idle time intervals: 2607614595
      in seconds: 130380729.750
      in hours: 36216.869

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 2
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000cca25110991d
    attached SAS address = 0x500605b00c2593d4
    attached phy identifier = 1
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization count = 0
    Phy reset problem count = 0
relative target port id = 2
  generation code = 2
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: power on
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000cca25110991e
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization count = 0
    Phy reset problem count = 0