Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- 8451860 bytes read in 508 ms (15.9 MiB/s)
- ## Booting kernel from Legacy Image at 12000000 ...
- Image Name: Linux
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 8451796 Bytes = 8.1 MiB
- Load Address: 10008000
- Entry Point: 10008000
- Verifying Checksum ... OK
- Loading Kernel Image ... OK
- Starting kernel ...
- Initializing cgroup subsys cpuset
- Initializing cgroup subsys cpu
- Linux version 3.1.2 (user@iMX6-bld) (gcc version 4.7.1 20120402 (prerelease) (cr osstool-NG linaro-1.13.1-2012.04-20120426 - Linaro GCC 2012.04) ) #128 SMP PREEM PT Sun Dec 8 09:02:21 UTC 2013
- CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
- CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
- Machine: Starterkit i.MX 6Solo Board
- Memory policy: ECC disabled, Data cache writealloc
- CPU identified as i.MX6DL/SOLO, silicon rev 1.1
- PERCPU: Embedded 7 pages/cpu @8bc06000 s6080 r8192 d14400 u32768
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 89088
- Kernel command line: console=ttymxc0,115200 consoleblank=0 dmfc=3 root=/dev/mmcb lk0p1 rootwait video=mxcfb1:dev=ldb,SK-ATM0704,if=RGB24 video=mxcfb0:dev=lcd,LDB -XGA,if=RGB24 ldb=dul1
- PID hash table entries: 2048 (order: 1, 8192 bytes)
- Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- allocated 2097152 bytes of page_cgroup
- please try 'cgroup_disable=memory' option if you don't want memory cgroups
- Memory: 352MB = 352MB total
- Memory: 345116k/345116k available, 179172k reserved, 0K highmem
- Virtual kernel memory layout:
- vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- DMA : 0xf4600000 - 0xffe00000 ( 184 MB)
- vmalloc : 0xa0800000 - 0xf2000000 (1304 MB)
- lowmem : 0x80000000 - 0xa0000000 ( 512 MB)
- pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
- modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
- .init : 0x80008000 - 0x8003e000 ( 216 kB)
- .text : 0x8003e000 - 0x807abdb4 (7608 kB)
- .data : 0x807ac000 - 0x808176b0 ( 430 kB)
- .bss : 0x808176d4 - 0x80887364 ( 448 kB)
- SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- Preemptible hierarchical RCU implementation.
- NR_IRQS:624
- MXC GPIO hardware
- sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
- Set periph_clk's parent to pll2_pfd_400M!
- arm_max_freq=1GHz
- MXC_Early serial console at MMIO 0x2020000 (options '115200')
- bootconsole [ttymxc0] enabled
- Console: colour dummy device 80x30
- Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
- pid_max: default: 32768 minimum: 301
- Mount-cache hash table entries: 512
- Initializing cgroup subsys cpuacct
- Initializing cgroup subsys memory
- Initializing cgroup subsys devices
- Initializing cgroup subsys freezer
- Initializing cgroup subsys blkio
- Initializing cgroup subsys perf_event
- CPU: Testing write buffer coherency: ok
- hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
- Brought up 1 CPUs
- SMP: Total of 1 processors activated (1581.05 BogoMIPS).
- devtmpfs: initialized
- print_constraints: dummy:
- NET: Registered protocol family 16
- print_constraints: vddpu: 725 <--> 1300 mV at 1150 mV fast normal
- print_constraints: vddcore: 725 <--> 1300 mV at 1150 mV fast normal
- print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal
- print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal
- print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal
- print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal
- hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
- hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
- hw-breakpoint: maximum watchpoint size is 4 bytes.
- L310 cache controller enabled
- l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x02050000, Cache size: 524288 B
- bio: create slab <bio-0> at 0
- mxs-dma mxs-dma-apbh: initialized
- print_constraints: vmmc: 3300 mV
- SCSI subsystem initialized
- spi_imx imx6q-ecspi.3: probed
- spi_imx imx6q-ecspi.0: probed
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- Freescale USB OTG Driver loaded, $Revision: 1.55 $
- imx-ipuv3 imx-ipuv3.0: IPU DMFC ONLY-DP HIGH RESOLUTION: 5B(0~3), 5F(4~7)
- Advanced Linux Sound Architecture Driver Version 1.0.24.
- Bluetooth: Core ver 2.16
- NET: Registered protocol family 31
- Bluetooth: HCI device and connection manager initialized
- Bluetooth: HCI socket layer initialized
- Bluetooth: L2CAP socket layer initialized
- Bluetooth: SCO socket layer initialized
- i2c-core: driver [max17135] using legacy suspend method
- i2c-core: driver [max17135] using legacy resume method
- Switching to clocksource mxc_timer1
- cfg80211: Calling CRDA to update world regulatory domain
- NET: Registered protocol family 2
- IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
- TCP established hash table entries: 16384 (order: 5, 131072 bytes)
- TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
- TCP: Hash tables configured (established 16384 bind 16384)
- TCP reno registered
- UDP hash table entries: 256 (order: 1, 8192 bytes)
- UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- NET: Registered protocol family 1
- RPC: Registered named UNIX socket transport module.
- RPC: Registered udp transport module.
- RPC: Registered tcp transport module.
- RPC: Registered tcp NFSv4.1 backchannel transport module.
- _regulator_get: etb supply vcore not found, using dummy regulator
- _regulator_get: etm.0 supply vcore not found, using dummy regulator
- Static Power Management for Freescale i.MX6
- wait mode is enabled for i.MX6
- cpaddr = a0820000 suspend_iram_base=a08b4000
- PM driver module loaded
- iMX6 PCIe PCIe RC mode imx_pcie_pltfm_probe entering.
- PCIE: imx_pcie_pltfm_probe start link up.
- link up failed, DB_R0:0x0022d400, DB_R1:0x08200000!
- IMX PCIe port: link down!
- IMX usb wakeup probe
- add wake up source irq 75
- IMX usb wakeup probe
- cpu regulator mode:ldo_enable
- i.MXC CPU frequency driver
- nfs4filelayout_init: NFSv4 File Layout Driver Registering...
- NTFS driver 2.1.30 [Flags: R/W].
- fuse init (API version 7.16)
- msgmni has been set to 674
- alg: No test for stdrng (krng)
- io scheduler noop registered
- io scheduler deadline registered
- io scheduler cfq registered (default)
- mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver lcd
- Console: switching to colour frame buffer device 128x48
- mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver ldb
- _regulator_get: get() with no identifier
- fbcvt: Invalid input parameters
- imx-sdma imx-sdma: loaded firmware 1.1
- imx-sdma imx-sdma: initialized
- Serial: IMX driver
- imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
- console [ttymxc0] enabled, bootconsole disabled
- console [ttymxc0] enabled, bootconsole disabled
- imx-uart.1: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX
- imx-uart.2: ttymxc2 at MMIO 0x21ec000 (irq = 60) is a IMX
- loop: module loaded
- GPMI NAND driver registered. (IMX)
- vcan: Virtual CAN interface driver
- CAN device driver interface
- flexcan netdevice driver
- flexcan imx6q-flexcan.1: device registered (reg_base=a0958000, irq=143)
- flexcan imx6q-flexcan.0: device registered (reg_base=a0960000, irq=142)
- FEC Ethernet Driver
- fec_enet_mii_bus: probed
- ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
- fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
- fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000
- fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- add wake up source irq 72
- fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
- fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
- fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200
- fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
- hub 2-0:1.0: USB hub found
- hub 2-0:1.0: 1 port detected
- Initializing USB Mass Storage driver...
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- ARC USBOTG Device Controller driver (1 August 2005)
- mousedev: PS/2 mouse device common for all mice
- _regulator_get: spi3.0 supply vcc not found, using dummy regulator
- ads7846 spi3.0: touchscreen, irq 362
- input: ADS7846 Touchscreen as /devices/platform/imx6q-ecspi.3/spi_master/spi3/sp i3.0/input/input0
- _regulator_get: spi0.0 supply vcc not found, using dummy regulator
- ads7846 spi0.0: touchscreen, irq 347
- input: ADS7846 Touchscreen as /devices/platform/imx6q-ecspi.0/spi_master/spi0/sp i0.0/input/input1
- i2c-core: driver [isl29023] using legacy suspend method
- i2c-core: driver [isl29023] using legacy resume method
- snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc0
- i2c /dev entries driver
- Linux video capture interface: v2.00
- mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16
- mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17
- mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video18
- imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
- Bluetooth: Generic Bluetooth USB driver ver 0.6
- usbcore: registered new interface driver btusb
- sdhci: Secure Digital Host Controller Interface driver
- sdhci: Copyright(c) Pierre Ossman
- _regulator_get: sdhci-esdhc-imx.2 supply vmmc not found, using dummy regulator
- mmc0: SDHCI controller on platform [sdhci-esdhc-imx.2] using ADMA
- mmc1: SDHCI controller on platform [sdhci-esdhc-imx.0] using ADMA
- mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
- VPU initialized
- mxc_asrc registered
- Galcore version 4.6.9.6622
- Thermal calibration data is 0x5644e85f
- Thermal sensor with ratio = 177
- Anatop Thermal registered as thermal_zone0
- anatop_thermal_probe: default cooling device is cpufreq!
- HDMI CEC initialized
- usbcore: registered new interface driver usbhid
- usbhid: USB HID core driver
- usbcore: registered new interface driver snd-usb-audio
- mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio
- imx-hdmi-soc-dai imx-hdmi-soc-dai.0: Failed: Load HDMI-video first.
- AIC23 Audio Codec 0.1
- asoc: tlv320aic23-hifi <-> imx-ssi.1 mapping ok
- Initialize HDMI-audio failed. Load HDMI-video first!
- ALSA device list:
- #0: sgtl5000-audio
- NET: Registered protocol family 26
- TCP cubic registered
- NET: Registered protocol family 17
- mmc0: new high speed DDR MMC card at address 0001
- can: controller area network core (rev 20090105 abi 8)
- usb 2-1: new high speed USB device number 2 using fsl-ehci
- NET: Registered protocol family 29
- mmcblk0: mmc0:0001 M4G1FB 3.64 GiB
- can: raw protocol (rev 20090105)
- can: broadcast manager protocol (rev 20090105 t)
- mmcblk0boot0: mmc0:0001 M4G1FB partition 1 1.00 MiB
- mmcblk0boot1: mmc0:0001 M4G1FB partition 2 1.00 MiB
- Bluetooth: RFCOMM TTY layer initialized
- Bluetooth: RFCOMM socket layer initialized
- Bluetooth: RFCOMM ver 1.11
- Bluetooth: BNEP (Ethernet Emulation) ver 1.3
- Bluetooth: BNEP filters: protocol multicast
- mmcblk0: p1
- Bluetooth: HIDP (Human Interface Emulation) ver 1.2
- mmcblk0boot1: unknown partition table
- lib80211: common routines for IEEE802.11 drivers
- VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
- Bus freq driver module loaded
- mmcblk0boot0: unknown partition table
- Bus freq driver Enabled
- mxc_dvfs_core_probe
- DVFS driver module loaded
- snvs_rtc snvs_rtc.0: setting system clock to 1970-01-01 00:00:10 UTC (10)
- EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem
- hub 2-1:1.0: USB hub found
- hub 2-1:1.0: 4 ports detected
- EXT4-fs (mmcblk0p1): recovery complete
- EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
- VFS: Mounted root (ext3 filesystem) on device 179:1.
- devtmpfs: mounted
- Freeing init memory: 216K
- EXT4-fs (mmcblk0p1): re-mounted. Opts: user_xattr,barrier=1,nodelalloc,data=orde red
- Starting logging: OK
- Populating /dev using udev: udevd[78]: starting version 1.9
- udevd[78]: specified group 'input' unknown
- done
- Starting watchdog...
- Initializing random number generator... done.
- Starting system message bus: done
- Starting network...
- eth0: Freescale FEC PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=1:00, ir q=-1)
- flexcan imx6q-flexcan.1: writing ctrl=0x0e312085
- Loading /usr/share/keymaps/i386/qwerty/ruwin_cplk-UTF-8.map.gz
- Starting sshd: OK
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement