Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- For my RGB setup, I'm using an RGB modded NES with Tim Worthington's NESRGB kit installed on the NES motherboard, along with a Voultar QSB kit for neat and simple wiring. My NES was also recently recapped, and the PSU was replaced with a Triad one to reduce any possible video noise from those sources.
- This was captured via an Insurrection Industries SNES SCART Sync on Luma cable (make sure to ask about the 2 ground pins actually being connected to avoid the possibility of dim buzzy audio/video for NES use). I've tried Retro Access cables, and was disappointed with the video I was seeing from them after running various capture tests with multiple compatible consoles and multiple types of sync. I ordered Csync and Sync on Luma from Retro Access, and both had less than stellar performance with regards to finding optimal phase, so I swapped back to the Insurrection cable and haven't looked back.
- My NES videos will all be using FirebrandX's palette "Digital Prime" for my NES runs. For anyone unfamiliar on why there's so much flexibility on color palettes with RGB modded NES consoles, the NES doesn't output true objective RGB colors, meaning there are no *objectively* correct colors for the NES. FirebrandX has put in tons of research and effort into trying to get his color palettes to look as accurate as possible, with many really solid ones over the years.
- Digital Prime, being the most recent one he did in 2021, aimed to look like NTSC colors as displayed on CRTs as closely as possible. I chose a couple of his palettes that I liked, and asked people who have played MTPO a ton on CRT TV's, and Digital Prime was the clear favorite. It was also the one I secretly preferred the most, so I am happy to settle with it for all my future NES speedruns.
- I'm using the Datapath E1 card, which is an internal capture card that is typically used for more serious applications, but these cards have been slowly phased out of usage for those applications as they get progressively obsoleted by better cards, so you'll find them on ebay for severely marked down, affordable 60-100 dollar prices (these usually cost thousands of dollars when they were sold new).
- One caveat is these loose cards almost always have the incorrect bracket, so they don't fit in your computer as is usually, and would require a full length bracket that's been 3D printed so it fits in nice and stable.
- Beyond this, I also needed some way to interface the SCART cable with the capture card, since this card only has a DVI port. You can either get a device known as a SCART2DVI on Insurrection Industries' website, or opt for a device that Voultar made called, and I'm not kidding, the "Double Penetration SD" which despite the crude name, is extremely convenient in that it splits the video to DVI, and also has a passthrough SCART output that's very useful for playing on a TV. I opted for the convenience of the second device, especially since the recording quality here appears excellent.
- Once I finally had all of this in place, I had to figure out the software for this capture card, and oh god, is this not like any other capture card I've ever used before. This card will capture your video feed from your console pixel perfectly, BUT you need to give it the exact correct information, otherwise it will look like a blurry mess.
- This information includes the exact horizontal resolution of the video signal it's receiving, which isn't actually how wide the picture is. This is a very specific internal value that you need to know, and this varies wildly from different hardware. For the NES, this value is always 341.
- You also need to adjust a value called "phase" which will make your video blurry if it's wrong, and if you change literally anything even slightly in your setup, this value will be completely different the next time you use it.
- The program this card uses (Vision Window) is one of the worst programs I've ever used. It has rampant glitches that will randomly change all your sensitive values that need to be exactly perfect if you ever press any buttons like "OK" and "Apply" to close the menu. Sometimes it'll just decide that your values will be completely different numbers arbitrarily, it's super fun.
- Also apparently you cannot have the latest firmware for the program, otherwise it'll run into an issue where any console power cycle (i.e. the reset or power buttons) will ruin the internal values you just set up. I needed to downgrade to Vision 7.11.2 to fix this issue.
- I also realized my test videos that I was recording all had incorrect colors compared to the palette I chose, so I had to very carefully color calibrate everything until it matched up with the original palette as close as reasonably possible
- At this point, I attempted to minimize the amount of artifacts in the boxing ring as best as I can on youtube uploads. Basically, with the way my first test uploads looked, the ring would have blocky artifacts that would rapidly flash between 2 similar colors constantly. It was pretty distracting, so I wanted to try to fix it if possible.
- The big thing that I ran into was an Avisynth function called TemporalSoften, which will smoothen adjacent pixels together, so long as they are similar enough in color. You have a couple of parameters you can play with, but eventually, I went with this line of code in my upscaling Avisynth script, which maxed out the parameters in such a way to where everything still looked natural, like NES footage is supposed to look: TemporalSoften(a,255,12,255,mode=1)
- I still noticed bits of noise in my video captures after uploading test videos to youtube, albeit it was significantly reduced after implementing TemporalSoften. I painstakingly messed with endless options until I realized that my color calibrations needed to be done in a very specific way.
- Basically, I needed to make sure that all colors had minimal flickering pixels between 2 slightly different color shades in all ring colors. Eventually, I found a combination of color settings that was still as close as possible to the intended palette, as well as maintaining strong solid colors for all the ring colors in the game.
- After all of that, I finally had a video that looked clean enough for me to accept for youtube uploads. It was a lot of trial and error, as well as times where several pieces of my capture chain would fail and require troubleshooting to get working again, but finally things are looking great.
- I'm also swapping over to recording runs on my Top Loader NES, as well as my AV Famicom, due to both of them having better reset circuits that never lose sync on Datapath cards.
Advertisement
Add Comment
Please, Sign In to add comment