=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.08.15 17:25:13 =~=~=~=~=~=~=~=~=~=~=~=
Š

E3C V3.06(May 29 2015 17:56:03)


Board: Ralink APSoC DRAM:  32 MB

relocate_code Pointer at: 81f9c000

spi_wait_nsec: 42

spi device id: ef 40 18 0 0 (40180000)

find flash: W25Q128BV

raspi_read: from:30000 len:1000

.raspi_read: from:30000 len:1000

.============================================

Ralink UBoot Version: 4.1.1.0

--------------------------------------------

ASIC 5350_MP (Port5<->None)

DRAM_CONF_FROM: Boot-Strapping

DRAM_TYPE: SDRAM

DRAM_SIZE: 256 Mbits

DRAM_WIDTH: 16 bits

DRAML_WIDTH: 16 bits

TOTAL_MEMORY_SIZE: 32 MBytes

Flash component: SPI Flash

Date:May 29 2015  Time:17:56:03

============================================

e: sets:256, ways:4, linesz:32 ,total:32768

dcache: sets:128, ways:4, linesz:32 ,total:16384


 ##### The CPU freq = 360 MHZ ####

 estimate memory size bytes

raspi_read: from:50000 len:10000

.verify_eep_macaddr: NOT eeprom!

raspi_read: from:50000 len:10000

.bi_flashsize=0x1000000


firmware_zone=0

arch.c->dev_type_detect()->line.650 : dev_name G502N found

RALINK_REG_GPIOMODE	(0xb0000060) end	=0x00400051

RT2880_REG_PIODIR	(0xb0000624) end	=0x003FBFFF


Please choose the operation:

   1: Load system code to SDRAM via TFTP.

   2: Load system code then write to Flash via TFTP.

   3: Boot system code via Flash (default).

   4: Entr boot command line interface.

   9: Load Boot Loader code then wri Flash via TFTP.

 2  1  0



3: System Boot system code via Flash.

## Booting image at bc0c0000 ...

raspi_read: from:c0000 len:40

.   Image Name:   Linux Kernel Image

   Image Type:   MIPS Linux Kernel Image (lzma compressed)

   Data Size:    719041 Bytes = 702.2 k Load Address: 80000000

   Entry Point:  8020d000

raspi_read: from:c0040 len:af8c1

...........   Verifying Checksum ... OK

   Uncompressing Kernel Image ... OK

## Kernel command line: console=ttyS1,115200n8 ramsize=32 hw_device=G502N firmware_zone=0 config_size=0x20000 firmware_size=0x7a0000 root=1f0b

No initrd

## Transferring control to Linux (at address 8020d000) ...

## Giving linux memsize in MB, 32


Stg kernel ...



LINUX started...

 THIS IS ASIC
Linux version 2.6.21 (root@localhost.localdomain) (gcc version 3.4.2) #1 Thu Oct 10 13:20:24 CST 2013

 The CPU frequency set to 360 MHz
CPU revision is: 0001964c
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 8128
Kernel command line: console=ttyS1,115200n8 root=/dev/mtdblock9
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = e0808068, status = 11000000
PID hash table entries: 128 (order: 7, 512 bytes)
calculating r4koff... 0015f900(1440000)
CPU frequency 360.00 MHz
Using 180.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 30188k/32768k available (1828k kernel code, 2580k reserved, 267k data, 108k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
deice id : ef 40 18 0 0 (40180000)
Time: MIPS clocksource has been installed.
W25Q128BV(ef 40180000) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
hw_device=G502N

Creating 14 MTD partitions on "raspi":
0x00000000-0x01000000 : "ALL"
0x00000000-0x00030000 : "Bootloader"
0x00030000-0x00040000 : "Mac"
0x00040000-0x00050000 : "Mac_bak"
0x00050000-0x00060000 : "Factory"
0x00060000-0x00080000 : "Config"
0x00080000-0x000a0000 : "Config_bak"
0x000a0000-0x000c0000 : "SystemLog"
0x000c0000-0x00170000 : "Kernel"
0x00170000-0x00860000 : "RootFs"
0x00860000-0x00910000 : "Kernel_bak"
0x00910000-0x01000000 : "RootFs_bak"
0x000c0000-0x00860000 : "Kernel_RootFs"
0x00860000-0x01000000 : "Kernel_RootFs_bak"
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
io scheduler noop registered (default)
Ralink gpio driver initialized
HDLC line discipline: version $Revision: #1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: #1 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0xb0000c00 (irq = 12) is a 16550A
loop: loaded (max 8 devices)
rdm_major = 253
Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors allocated, mtu = 1500!
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x432880e5
PROC INIT OK!
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
PPTP driver version 0.8.1
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
block2mtd: version $Revision: #1 $
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 108k freed

init started: BusyBox v1.12.1 (2013-10-10 13:22:55 CST)

starting pid 13, tty '': '/etc_ro/rcS'
Algorithmics/MIPS FPU Emulator v1.5
devpts: called with bogus options
mount: mounting none on /proc/bus/usb failed: No such file or directory
/etc_ro/rcS: /sbin/global.sh: line 58: getPriorLink: not found
rmmod: ralink_wdt.o: No such file or directory
Ralink APSoC Hardware Watchdog Timer
Started WatchDog Timer.
/sbin/syslog.sh: /sbin/global.sh: line 58: getPriorLink: not found
syslog: rows=200 level=6 trace=1

power off 9
switch register base addr to 0xb0110000
write offset 0x168, value 0x10
Password for 'admin' changed
Raeth v3.0 (Tasklet,SkbRecycle)

phy_tx_ring = 0x01cc1000, tx_ring = 0xa1cc1000

phy_rx_ring0 = 0x01cc2000, rx_ring0 = 0xa1cc2000
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x432880e5
RT305x_ESW: Link Status Changed
ra2880stop()...Done
Free TX/RX Ring Memory!
Raeth v3.0 (Tasklet,SkbRecycle)

phy_tx_ring = 0x01cc3000, tx_ring = 0xa1cc3000

phy_rx_ring0 = 0x013dc000, rx_ring0 = 0xa13dc000
GMAC1_MAC_ADRH -- : 0x00000021
GMAC1_MAC_ADRL -- : 0xf211e224
RT305x_ESW: Link Status Changed
rmmod: rt2860v2_ap: No such file or directory
rmmod: rt2860v2_sta: No such file or directory
rmmod: nf_nat_pptp: No such file or directory
rmmod: nf_conntrack_pptp: No such file or directory
rmmod: nf_nat_proto_gre: No such file or directory
rmmod: nf_conntrack_proto_gre: No such file or directory
rmmod: nf_conntrack_sip: No such file or directory
rmmod: nf_conntrack_h323: No such file or directory
rmmod: nf_conntrack_ftp: No such file or directory
rmmod: nf_conntrack_rtsp: No such file or directory
rmmod: nf_nat_sip: No such file or directory
rmmod: nf_nat_h323: No such file or directory
rmmod: nf_nat_ftp: No such file or directory
rmmod: nf_nat_rtsp: No such file or directory
switch register base addr to 0xb0110000
write offset 0x168, value 0x10
Set: phy[4].reg[0] = 3100
Set: phy[0].reg[0] = 3100
port_status_get.c port_link_status_get no such port:-1
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
prior_link=wired
1
wan_pvid=1
killall: wantap: no process killed
phy_link=wired
index=1;wan_id=1;vid=5;is_br=Route;key_word=tr069_goahead_telnet_snmp_sip_rtp;bind_lan=_lan2_lan3_lan4;tag_mode=1
eth2.5: Setting MAC address to  00 21 f2 11 e2 25.
device eth2 entered promiscuous mode
VLAN (eth2.5):  Setting underlying device (eth2) to promiscious mode.
wanif=eth2.5;is_shared_vlan=
2
lan_pvid=2
eth2.2: Setting MAC address to  00 21 f2 11 e2 24.
VLAN (eth2.2):  Underlying device (eth2) has same MAC, not checking promiscious mode.
lan_vif=eth2.2
br0: port 1(eth2.2) entering learning state
lan_pvid=2;lan_vif=eth2.2
dev_manage_stat_set SwVlan1 enable,5,tag,unset,unset,unset,unset
lan=lan1;is_bind=0;bind_lan=_lan2_lan3_lan4
lan=lan2;is_bind=1;bind_lan=_lan2_lan3_lan4
lan=lan3;is_bind=1;bind_lan=_lan2_lan3_lan4
lan=lan4;is_bind=1;bind_lan=_lan2_lan3_lan4
/sbin/muti-wan.sh: line 1: ebtables: not found
dev_manage_stat_set SwVlan2 enable,2,unset,unset,untag,untag,untag
wlan=ra0;is_bind=1
/sbin/muti-wan.sh: line 1: ebtables: not found
wlan=ra1;is_bind=1
/sbin/muti-wan.sh: line 1: ebtables: not found
wlan=ra2;is_bind=1
/sbin/muti-wan.sh: line 1: ebtables: not found
wlan=ra3;is_bind=1
/sbin/muti-wan.sh: line 1: ebtables: not found
index=2;wan_id=2;vid=100;is_br=Bridge;key_word=internet;bind_lan=_lan1;tag_mode=1
eth2.100: Setting MAC address to  00 21 f2 11 e2 25.
wanif=eth2.100;is_shared_vlan=
br0: port 2(eth2.100) entering learning state
brctl addif br0 eth2.100
/sbin/muti-wan.sh: line 1: ebtables: not found
/sbin/muti-wan.sh: line 1: ebtables: not found
/sbin/muti-wan.sh: line 1: ebtables: not found
/sbin/muti-wan.sh: line 1: ebtables: not found
is_soft_br=0;lan_pvid=100
device eth2.100 left promiscuous mode
br0: port 2(eth2.100) entering disabled state
lan=lan1;is_bind=1;bind_lan=_lan1
lan=lan2;is_bind=0;bind_lan=_lan1
lan=lan3;is_bind=0;bind_lan=_lan1
lan=lan4;is_bind=0;bind_lan=_lan1
/sbin/muti-wan.sh: line 1: ebtables: not found
dev_manage_stat_set SwVlan3 enable,100,tag,untag,unset,unset,unset
/sbin/muti-wan.sh: line 1: ebtables: not found
configEsw_E3C!!!!!!!!!!!!!!!!
switch reg write offset=14, value=ff5555
switch reg write offset=50, value=2001
switch reg write offset=98, value=ff3f
switch reg write offset=c8, value=1f502828
switch reg write offset=e4, value=5e000000
switch reg write offset=8, value=a1a07850
switch reg write offset=c, value=30
switch reg write offset=18, value=f0f0f0f
switch reg write offset=84, value=20
done.
cat: can't open '/var/run/udhcpc_eth2.5.pid': No such file or directory
udhcpc (v1.12.1) started
No ip for interface eth2.100
br0: port 1(eth2.2) entering disabled state
br0: port 1(eth2.2) entering learning state
ifconfig: ioctl 0x8913 failed: No such device
/sbin/lan.sh: line 161: cannot create /proc/sys/net/ipv6/conf/all/forwarding: nonexistent directory
+ get_array_element eth2.5	eth2.100 1
+ echo eth2.5	eth2.100
+ awk -v i=1 {len=split($0,ta,"\t"); print ta[i]}
+ telnet_if_name1=eth2.5
+ get_array_element eth2.5	eth2.100 1
+ echo eth2.5	eth2.100
+ awk -v i=1 {len=split($0,ta,"\t"); print ta[i]}
+ goahead_if_name1=eth2.5
+ iptables -D INPUT -j web_filter
iptables v1.4.0rc1: Couldn't find target `web_filter'

Try `iptables -h' or 'iptables --help' for more information.
+ iptables -F web_filter
iptables: No chain/target/match by that name
+ iptables -t filter -N web_filter
+ iptables -t filter -A INPUT -j web_filter
+ echo iptables -t filter -A INPUT -j web_filter
+ [ 1 == 1 ]
+ iptables -A web_filter -p tcp --dport 23 -i eth2.5 -j ACCEPT
+ echo iptables -A web_filter -p tcp --dport  23 -i eth2.5 -j ACCEPT
+ [ eth2.5 != eth2.5 ]
+ iptables -A web_filter -p tcp --dport 23 -i br0 -j ACCEPT
+ echo iptables -A web_filter -p tcp --dport 23 -i br0 -j ACCEPT
+ iptables -A web_filter -p tcp --dport 80 -i eth2.5 -j ACCEPT
+ echo iptables -A web_filter -p tcp --dport 80 -i eth2.5 -j ACCEPT
+ [ eth2.5 != eth2.5 ]
+ iptables -A web_filter -p tcp --dport 80 -i br0 -j ACCEPT
+ echo iptables -A web_filter -p tcp --dport 80  -i br0 -j ACCEPT
+ iptables -A web_filter -p tcp --dport 80 -j DROP
+ echo iptables -A web_filter -p tcp --dport 80  -j DROP
+ iptables -A web_filter -p tcp --dport 23 -j DROP
+ echo iptables -A web_filter -p tcp --dport 23 -j DROP
+ set +x
/sbin/internet.sh: line 363: config_ipv6.sh: not found
tz=GMT-1
tzn=-1
ntp.ngi.it: Unknown host
ntp dns error: No such file or directory
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
insmod: cannot insert '/lib/modules/2.6.21/kernel/drivers/char/watchdog/ralink_wdt.ko': invalid parameters
/sbin/internet.sh: line 414: soft-qos.sh: not found
/sbin/internet.sh: line 416: mdev: not found
G501N_EOLO
start provision now
[ralink_init] mkdir -p /etc/provision

DEV_TRACE dev_manager.c->line.952 : goahead PID=1881 dev_man_has_init=0
DEV_TRACE dev_manager.c->line.823 : even=config, callback=00000000
DEV_TRACE dev_manager.c->line.823 : even=config, callback=00440650
DEV_TRACE dev_manager.c->line.785 : goahead PID=1894
goahead: webs v1.2 start...
goahead: webs: rootWeb=/etc_ro/web

goahead: webs: Listening for HTTP requests at address 192.168.1.1

[ralink_init] write /etc/provision/provision.conf

[ralink_init] read /etc_ro/provision/provision_default

provision[1902]: start
[Provision_Debug]: wan_if: eth2.2
[Provision_Debug]: Delay: 26
start snmpd now
[ralink_init] mkdir -p /etc/snmpd

[ralink_init] write /etc/snmpd/snmpd.conf

[ralink_init] read /etc_ro/snmpd/snmpd_default

snmpd[1913]: start
udpSend: Network is unreachable
start voip now
/usr/sbin/fv_drv.sh: /sbin/global.sh: line 58: getPriorLink: not found
check dev is G502N
cpld_init: dev_name=G502N watch_dog=0



ATA board version 0x21

RALINK_REG_GPIOMODE	(0xb0000060) begin	=0x004000DD
RALINK_REG_GPIOMODE	(0xb0000060) end	=0x004000D1
RTPD: Success: rx address = 0xa18a5000
RTPD: Success: rx address = 0xa18a6000
RTPD: Success: rx address = 0xa18a7000
RTPD: Success: rx address = 0xa1848000
RTPD: Success: rx address = 0xa1849000
RTPD: Success: rx address = 0xa184a000
RTPD: Success: rx address = 0xa184b000
RTPD: Success: rx address = 0xa1840000
RTPD: Success: pcm_dma_create_buf
RTPD: rtpd_reg_setup
pcm_reg_setup:PCM_PCMCFG=43330004
PCM_FSYNC_CFG=0x00000000
Success: IIS_DMA request_irq ok
RTPD: rtpd_ch_enable_pcm
CPLD driver for IP652 ,Linux 2.6.21.x

CPLD driver version : D2.7.4

BuildTime:May 23 2013 11:47:56



[ralink_init] mkdir -p /etc/ipphone

[ralink_init] write /etc/ipphone/ipphone.conf

[ralink_init] read /etc_ro/ipphone/ipphone_default

pool.ntp.org: Unknown host
ntp dns error: No such file or directory

starting pid 1996, tty '/dev/ttyS1': '/bin/sh'


BusyBox v1.12.1 (2013-10-10 13:22:55 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

# main PID=1978
DEV_TRACE dev_manager.c->line.952 : ipphone PID=1978 dev_man_has_init=0
DEV_TRACE dev_manager.c->line.785 : ipphone PID=2002
DEV_TRACE dev_manager.c->line.823 : even=config, callback=00000000
looptask[1995]: start
TaskManager PID=2008

 SoftWare Ver:142 C
 DB Params Ver:20070522
 Build Time:Oct 10 2013 13:28:21
 __GNUC__ : 3

Application starting ...
DEV_TRACE dev_manager.c->line.823 : even=config, callback=0043cfe8
DEV_TRACE dev_manager.c->line.823 : even=upgrade, callback=0043d044
DEV_TRACE dev_manager.c->line.823 : even=reboot, callback=0043d000
create_dsp 0 start
create dsp 0 ok
create_dsp 1 start
create dsp 1 ok
create_dsp 2 start
create dsp 2 ok
create_dsp 3 start
create dsp 3 ok
open /dev/sim faild!
open /dev/sim faild!
open /dev/sim fail
FV_ERROR >>> ks_gpio_test.c->fv_voip_led_set()->line.387 : gpio=-1 on=4000 off=0 blinks=0


sim init SIM_NOT_FOUND

FV_ERROR >>> ks_gpio_test.c->fv_voip_led_set()->line.387 : gpio=1 on=4000 off=0 blinks=0
FV_ERROR >>> ks_gpio_test.c->fv_voip_led_set()->line.387 : gpio=-1 on=4000 off=0 blinks=0
voip_NewTimerLoopTask PID=2066
SMS TASK Spawn start....
MiscellaneousTask PID=2067
SMS TASK Spawn already  start....
ConfigManager PID=2068
ipphone[2068]: ***system booting***
ipphone[2067]: MiscellaneousTask: start work param_count=0,single_param_count=1

ipphone[2068]: SW:142(120106174008)
PhManSubTM PID=2075
ControlSender PID=2076
DSPCtrlMsgDecoder PID=2077
CodecManager PID=2078
******CodecManager_SetTxGain: Ok  vol=5, db=0

******CodecManager_SetRxGain: Ok  vol=5, db=0

HookStatusPoll PID=2079
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
TelCtrlSubTM PID=2145
CallControl PID=2146
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
port_status_get.c port_link_status_get no such port:-1
port_status_get link status get error
VoiceManager PID=2176
VoiceTransmitTaskChannel PID=2178
JitterControl PID=2177
VoiceTransmitTaskChannel PID=2179
ACSubTM PID=2190
KeypadManager PID=2191
UIDM_LED_Task PID=2192
UIControl PID=2193
IVRTask PID=2194
Release the general semaphore
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
snd_ctrl_to_dsp[2]len=4 cmd=160: 160 004 026 000
snd_ctrl_to_dsp[2]len=3 cmd=152: 152 003 000
snd_ctrl_to_dsp[2]len=3 cmd=153: 153 003 000
snd_ctrl_to_dsp[2]len=4 cmd=154: 154 004 000 000
EndRecordCallLog not find call 255

EndRecordCallLog not find call 255

EndRecordCallLog not find call 255

EndRecordCallLog not find call 255

ipphone[2193]: UISignalControl[30][9000][30][9000][9000]
snd_ctrl_to_dsp[2]len=3 cmd=222: 222 003 000
ntp.ngi.it: Unknown host
ntp dns error: No such file or directory
br0: topology change detected, propagating
br0: port 1(eth2.2) entering forwarding state
ipphone[2008]: TZ change to GMT-1

pool.ntp.org: Unknown host
ntp dns error: No such file or directory
ntp.ngi.it: Unknown host
ntp dns error: No such file or directory
pool.ntp.org: Unknown host
ntp dns error: No such file or directory
[Provision_Debug]: Sate: IDLE
[Provision_Debug]: Delay: 0
[Provision_Debug]: Sate: UPDATE_CFG
[Provision_Debug]: option66=1, tftpserver=
[Provision_Debug]: Update configuration fialed, retry 3600 s later......
[Provision_Debug]: Delay: 3600
ntp.ngi.it: Unknown host
ntp dns error: No such file or directory
pool.ntp.org: Unknown host
ntp dns error: No such file or directory