Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 1.1.3 (May 13 2020 - 19:39:06)
- Board: Ralink APSoC DRAM: 128 MB
- relocate_code Pointer at: 87f58000
- Config XHCI 40M PLL
- flash manufacture id: ef, device id 40 18
- find flash: W25Q128BV
- *** Warning - bad CRC, using default environment
- ============================================
- Ralink UBoot Version: 5.0.0.0
- --------------------------------------------
- ASIC MT7621A DualCore (MAC to MT7530 Mode)
- DRAM_CONF_FROM: Auto-Detection
- DRAM_TYPE: DDR3
- DRAM bus: 16 bit
- Xtal Mode=3 OCP Ratio=1/3
- Flash component: SPI Flash
- Date:May 13 2020 Time:19:39:06
- ============================================
- THIS IS uboot
- icache: sets:256, ways:4, linesz:32 ,total:32768
- dcache: sets:256, ways:4, linesz:32 ,total:32768
- ##### The CPU freq = 880 MHZ ####
- estimate memory size =128 Mbytes
- Press '4' or 't' to break the booting process
- Press 'x' to enter recovery web server
- nm_init:791
- nm_initFwupPtnStruct:276
- nm_lib_readPtnTable:738
- [NM_Debug](nm_lib_readPtnTable) 00743: NM_PTN_TABLE_BASE = 0xfe0000
- [NM_Debug](nm_lib_readPtnFromNvram) 00569: partition_used_len = 1054, requried len = 8192
- [NM_Debug](nm_lib_readPtnTable) 00751: Reading Partition Table from NVRAM ... OK
- [NM_Debug](nm_lib_readPtnTable) 00759: Parsing Partition Table ... OK
- [NM_Debug](nm_lib_readPtnFromNvram) 00569: partition_used_len = 2, requried len = 2
- factory boot check integer ok.
- 3: System Boot system code via Flash.
- ## Booting image at bc040000 ...
- Image Name: MIPS OpenWrt Linux-5.4.179
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 2380777 Bytes = 2.3 MB
- Load Address: 80001000
- Entry Point: 80001000
- Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80001000) ...
- ## Giving linux memsize in MB, 128
- Starting kernel ...
- [ 0.000000] Linux version 5.4.179 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16495-bf0c965af0)) #0 SMP Wed Feb 16 20:29:10 2022
- [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
- [ 0.000000] printk: bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
- [ 0.000000] MIPS: machine is TP-Link Archer A6 v3
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] VPE topology {2,2} total 4
- [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
- [ 0.000000] HighMem empty
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
- [ 0.000000] percpu: Embedded 14 pages/cpu s26768 r8192 d22384 u57344
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
- [ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
- [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
- [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
- [ 0.000000] Writing ErrCtl register=00022040
- [ 0.000000] Readback ErrCtl register=00022040
- [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
- [ 0.000000] Memory: 120968K/131072K available (6095K kernel code, 204K rwdata, 748K rodata, 1260K init, 238K bss, 10104K reserved, 0K cma-reserved, 0K highmem)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
- [ 0.000000] rcu: Hierarchical RCU implementation.
- [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
- [ 0.000000] NR_IRQS: 256
- [ 0.000000] random: get_random_bytes called from 0x806e5a3c with crng_init=0
- [ 0.000000] CPU Clock: 880MHz
- [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
- [ 0.000008] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
- [ 0.007811] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360)
- [ 0.042001] pid_max: default: 32768 minimum: 301
- [ 0.046769] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.053996] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.064372] rcu: Hierarchical SRCU implementation.
- [ 0.069790] smp: Bringing up secondary CPUs ...
- [ 0.075911] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.075922] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 0.075933] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
- [ 0.076034] CPU1 revision is: 0001992f (MIPS 1004Kc)
- [ 0.102530] Synchronize counters for CPU 1: done.
- [ 0.143398] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.143407] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 0.143414] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
- [ 0.143473] CPU2 revision is: 0001992f (MIPS 1004Kc)
- [ 0.167247] Synchronize counters for CPU 2: done.
- [ 0.198609] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.198616] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 0.198624] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
- [ 0.198687] CPU3 revision is: 0001992f (MIPS 1004Kc)
- [ 0.225101] Synchronize counters for CPU 3: done.
- [ 0.254980] smp: Brought up 1 node, 4 CPUs
- [ 0.263468] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
- [ 0.273159] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
- [ 0.280171] pinctrl core: initialized pinctrl subsystem
- [ 0.287006] NET: Registered protocol family 16
- [ 0.316447] clocksource: Switched to clocksource GIC
- [ 0.322893] thermal_sys: Registered thermal governor 'step_wise'
- [ 0.323360] NET: Registered protocol family 2
- [ 0.333798] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
- [ 0.341919] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
- [ 0.350398] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.357983] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
- [ 0.364975] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.371418] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
- [ 0.377897] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
- [ 0.385057] NET: Registered protocol family 1
- [ 0.389368] PCI: CLS 0 bytes, default 32
- [ 0.484385] 4 CPUs re-calibrate udelay(lpj = 1167360)
- [ 0.490993] workingset: timestamp_bits=14 max_order=15 bucket_order=1
- [ 0.498316] random: fast init done
- [ 0.509986] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.515751] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.527282] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
- [ 0.536480] mt7621_gpio 1e000600.gpio: registering 32 gpios
- [ 0.542318] mt7621_gpio 1e000600.gpio: registering 32 gpios
- [ 0.548077] mt7621_gpio 1e000600.gpio: registering 32 gpios
- [ 0.554430] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 0.564271] printk: console [ttyS0] disabled
- [ 0.568559] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
- [ 0.577538] printk: console [ttyS0] enabled
- [ 0.577538] printk: console [ttyS0] enabled
- [ 0.585796] printk: bootconsole [early0] disabled
- [ 0.585796] printk: bootconsole [early0] disabled
- [ 0.598195] spi-mt7621 1e000b00.spi: sys_freq: 220000000
- [ 0.614089] spi-nor spi0.0: w25q128 (16384 Kbytes)
- [ 0.618941] 4 fixed-partitions partitions found on MTD device spi0.0
- [ 0.625279] Creating 4 MTD partitions on "spi0.0":
- [ 0.630069] 0x000000000000-0x000000040000 : "u-boot"
- [ 0.636342] 0x000000040000-0x000000fa0000 : "firmware"
- [ 0.642940] 2 uimage-fw partitions found on MTD device firmware
- [ 0.648868] Creating 2 MTD partitions on "firmware":
- [ 0.653831] 0x000000000000-0x000000245429 : "kernel"
- [ 0.660013] 0x000000245429-0x000000f60000 : "rootfs"
- [ 0.666136] mtd: device 3 (rootfs) set to be root filesystem
- [ 0.671885] 1 squashfs-split partitions found on MTD device rootfs
- [ 0.678067] 0x000000660000-0x000000f60000 : "rootfs_data"
- [ 0.684846] 0x000000fa0000-0x000000ff0000 : "config"
- [ 0.691122] 0x000000ff0000-0x000001000000 : "radio"
- [ 0.723075] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
- [ 0.732684] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
- [ 0.742964] mt7621-pci 1e140000.pcie: Parsing DT failed
- [ 0.750768] NET: Registered protocol family 10
- [ 0.756727] Segment Routing with IPv6
- [ 0.760540] NET: Registered protocol family 17
- [ 0.765063] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
- [ 0.778233] 8021q: 802.1Q VLAN Support v1.8
- [ 0.784237] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
- [ 0.800678] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY]
- [ 0.810296] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY]
- [ 0.820011] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY]
- [ 0.829700] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY]
- [ 0.839424] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY]
- [ 0.849216] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
- [ 0.860438] DSA: tree 0 setup
- [ 0.863741] rt2880-pinmux pinctrl: pcie is already enabled
- [ 0.869375] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
- [ 0.876953] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
- [ 0.984361] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
- [ 0.989942] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
- [ 1.095447] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
- [ 1.102396] mt7621-pci 1e140000.pcie: PCIE0 enabled
- [ 1.107264] mt7621-pci 1e140000.pcie: PCIE1 enabled
- [ 1.112140] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
- [ 1.121603] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
- [ 1.127961] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
- [ 1.134824] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
- [ 1.141686] pci_bus 0000:00: root bus resource [bus 00-ff]
- [ 1.147199] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
- [ 1.153226] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
- [ 1.159482] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
- [ 1.165808] pci 0000:00:00.0: supports D1
- [ 1.169813] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
- [ 1.175933] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
- [ 1.181972] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
- [ 1.188229] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
- [ 1.194544] pci 0000:00:01.0: supports D1
- [ 1.198548] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
- [ 1.205729] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
- [ 1.213729] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
- [ 1.221928] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000
- [ 1.227973] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
- [ 1.234370] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
- [ 1.241890] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
- [ 1.247119] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
- [ 1.253203] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff]
- [ 1.259976] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref]
- [ 1.267188] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
- [ 1.273994] pci 0000:02:00.0: [14c3:7663] type 00 class 0x000280
- [ 1.280049] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
- [ 1.287273] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
- [ 1.294494] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
- [ 1.301816] pci 0000:02:00.0: supports D1 D2
- [ 1.306081] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
- [ 1.312725] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
- [ 1.327918] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
- [ 1.333151] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
- [ 1.339232] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff]
- [ 1.346007] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff pref]
- [ 1.353219] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
- [ 1.359862] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
- [ 1.366469] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
- [ 1.373419] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
- [ 1.380015] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
- [ 1.386966] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
- [ 1.393745] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
- [ 1.400954] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
- [ 1.407727] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x604fffff pref]
- [ 1.414936] pci 0000:00:00.0: BAR 1: assigned [mem 0x60500000-0x6050ffff]
- [ 1.421719] pci 0000:00:01.0: BAR 1: assigned [mem 0x60510000-0x6051ffff]
- [ 1.428499] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
- [ 1.435272] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
- [ 1.442062] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
- [ 1.448841] pci 0000:00:00.0: PCI bridge to [bus 01]
- [ 1.453798] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
- [ 1.460574] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
- [ 1.467345] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
- [ 1.474562] pci 0000:02:00.0: BAR 0: assigned [mem 0x60300000-0x603fffff 64bit pref]
- [ 1.482304] pci 0000:02:00.0: BAR 2: assigned [mem 0x60400000-0x60403fff 64bit pref]
- [ 1.490044] pci 0000:02:00.0: BAR 4: assigned [mem 0x60404000-0x60404fff 64bit pref]
- [ 1.497781] pci 0000:00:01.0: PCI bridge to [bus 02]
- [ 1.502737] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
- [ 1.509513] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
- [ 1.516284] pci 0000:00:01.0: bridge window [mem 0x60300000-0x604fffff pref]
- [ 1.524232] hctosys: unable to open rtc device (rtc0)
- [ 1.532966] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
- [ 1.536095] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
- [ 1.551414] Freeing unused kernel memory: 1260K
- [ 1.555960] This architecture does not have kernel memory protection.
- [ 1.562383] Run /sbin/init as init process
- [ 2.140025] init: Console is alive
- [ 2.143681] init: - watchdog -
- [ 2.839128] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 2.933947] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 2.952758] init: - preinit -
- [ 3.630765] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
- [ 3.639070] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
- [ 3.647551] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
- [ 3.769430] random: jshn: uninitialized urandom read (4 bytes read)
- [ 3.834007] random: jshn: uninitialized urandom read (4 bytes read)
- [ 3.881161] random: jshn: uninitialized urandom read (4 bytes read)
- [ 4.134486] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
- [ 4.141552] 8021q: adding VLAN 0 to HW filter on device lan1
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 8.351620] jffs2: notice: (592) jffs2_build_xattr_subsystem: complete building xattr subsystem, 7 of xdatum (0 unchecked, 2 orphan) and 8 of xref (2 dead, 0 orphan) found.
- [ 8.368947] mount_root: switching to jffs2 overlay
- [ 8.380220] overlayfs: upper fs does not support tmpfile.
- [ 8.390895] urandom-seed: Seeding with /etc/urandom.seed
- [ 8.488799] procd: - early -
- [ 8.491769] procd: - watchdog -
- [ 9.080556] procd: - watchdog -
- [ 9.084469] procd: - ubus -
- [ 9.243935] procd: - init -
- Please press Enter to activate this console.
- [ 9.864975] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 9.884054] Loading modules backported from Linux version v5.10.85-0-ge4f2aee6612e
- [ 9.891695] Backport generated by backports.git v5.10.85-1-0-gf988973f
- [ 9.915159] xt_time: kernel timezone is -0000
- [ 9.993278] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=23
- [ 9.998733] pci 0000:00:00.0: enabling device (0004 -> 0007)
- [ 9.999665] urngd: v1.0.2 started.
- [ 10.004431] mt7603e 0000:01:00.0: enabling device (0000 -> 0002)
- [ 10.014001] mt7603e 0000:01:00.0: ASIC revision: 76030010
- [ 10.150204] crng init done
- [ 10.152939] random: 7 urandom warning(s) missed due to ratelimiting
- [ 10.637832] mt7603e 0000:01:00.0: Firmware Version: ap_pcie
- [ 10.643425] mt7603e 0000:01:00.0: Build Time: 20160107100755
- [ 10.676430] mt7603e 0000:01:00.0: firmware init done
- [ 10.868726] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=24
- [ 10.874183] pci 0000:00:01.0: enabling device (0004 -> 0007)
- [ 10.879857] mt7615e 0000:02:00.0: enabling device (0000 -> 0002)
- [ 10.922616] PPP generic driver version 2.4.2
- [ 10.930133] NET: Registered protocol family 24
- [ 10.952388] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 11.101402] mt7615e 0000:02:00.0: HW/SW Version: 0x65326363, Build Time: 2005101654debug
- [ 11.101402]
- [ 11.355172] mt7615e 0000:02:00.0: N9 Firmware Version: 7663mp1827, Build Time: 20200512032642
- [ 11.363738] mt7615e 0000:02:00.0: Region number: 0x4
- [ 11.368749] mt7615e 0000:02:00.0: Parsing tailer Region: 0
- [ 11.377627] mt7615e 0000:02:00.0: Region 0, override_addr = 0x00118000
- [ 11.384203] mt7615e 0000:02:00.0: Parsing tailer Region: 1
- [ 11.390893] mt7615e 0000:02:00.0: Parsing tailer Region: 2
- [ 11.396988] mt7615e 0000:02:00.0: Parsing tailer Region: 3
- [ 11.404914] mt7615e 0000:02:00.0: override_addr = 0x00118000, option = 3
- [ 17.049719] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
- [ 17.067005] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
- [ 17.075336] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
- [ 17.078854] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
- [ 17.091562] 8021q: adding VLAN 0 to HW filter on device lan1
- [ 17.100664] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
- [ 17.107765] br-lan: port 1(lan1) entered blocking state
- [ 17.113095] br-lan: port 1(lan1) entered disabled state
- [ 17.119512] device lan1 entered promiscuous mode
- [ 17.124297] device eth0 entered promiscuous mode
- [ 17.156172] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
- [ 17.163699] 8021q: adding VLAN 0 to HW filter on device lan2
- [ 17.173184] br-lan: port 2(lan2) entered blocking state
- [ 17.178557] br-lan: port 2(lan2) entered disabled state
- [ 17.185093] device lan2 entered promiscuous mode
- [ 17.202641] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
- [ 17.210228] 8021q: adding VLAN 0 to HW filter on device lan3
- [ 17.220049] br-lan: port 3(lan3) entered blocking state
- [ 17.225394] br-lan: port 3(lan3) entered disabled state
- [ 17.232583] device lan3 entered promiscuous mode
- [ 17.250762] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode
- [ 17.258068] 8021q: adding VLAN 0 to HW filter on device lan4
- [ 17.267894] br-lan: port 4(lan4) entered blocking state
- [ 17.273235] br-lan: port 4(lan4) entered disabled state
- [ 17.280248] device lan4 entered promiscuous mode
- [ 17.304478] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode
- [ 17.311621] 8021q: adding VLAN 0 to HW filter on device wan
- [ 18.736278] br-lan: port 5(wlan1) entered blocking state
- [ 18.741687] br-lan: port 5(wlan1) entered disabled state
- [ 18.747797] device wlan1 entered promiscuous mode
- [ 18.753033] br-lan: port 5(wlan1) entered blocking state
- [ 18.758501] br-lan: port 5(wlan1) entered forwarding state
- [ 18.765992] br-lan: port 5(wlan1) entered disabled state
- [ 18.799528] br-lan: port 6(wlan0) entered blocking state
- [ 18.805005] br-lan: port 6(wlan0) entered disabled state
- [ 18.811258] device wlan0 entered promiscuous mode
- [ 18.816592] br-lan: port 6(wlan0) entered blocking state
- [ 18.821990] br-lan: port 6(wlan0) entered forwarding state
- [ 18.829647] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
- [ 18.960970] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- [ 19.250130] CPU 2 Unable to handle kernel paging request at virtual address 00000000, epc == 86dda8a0, ra == 86ddb5a0
- [ 19.260868] Oops[#1]:
- [ 19.263173] CPU: 2 PID: 1543 Comm: hostapd Not tainted 5.4.179 #0
- [ 19.269252] $ 0 : 00000000 00000001 00000038 00000001
- [ 19.274463] $ 4 : 00000018 00000008 00000003 00000000
- [ 19.279670] $ 8 : 00000000 00000064 00000000 00000000
- [ 19.284878] $12 : 00000000 8681f9e8 00000008 000005ee
- [ 19.290083] $16 : 00000000 00000001 86816068 86816050
- [ 19.295289] $20 : 000003e8 00000001 0000145a 00000000
- [ 19.300506] $24 : 00000002 8680134c
- [ 19.305728] $28 : 8681e000 8681f7f0 86e17124 86ddb5a0
- [ 19.310938] Hi : ccccc547
- [ 19.313801] Lo : 66666485
- [ 19.316692] epc : 86dda8a0 0x86dda8a0 [mt76_connac_lib@c3ed30b7+0x4e80]
- [ 19.323451] ra : 86ddb5a0 0x86ddb5a0 [mt76_connac_lib@c3ed30b7+0x4e80]
- [ 19.330206] Status: 11007c03 KERNEL EXL IE
- [ 19.334377] Cause : 40800008 (ExcCode 02)
- [ 19.338364] BadVA : 00000000
- [ 19.341231] PrId : 0001992f (MIPS 1004Kc)
- [ 19.345304] Modules linked in: pppoe ppp_async iptable_nat xt_state xt_nat xt_conntrack xt_REDIRECT xt_MASQUERADE xt_FLOWOFFLOAD xt_CT pppox ppp_generic nf_nat nf_flow_table_hw nf_flow_table nf_conntrack mt7615e mt7615_common mt7603e mt76_connac_lib mt76 mac80211 ipt_REJECT cfg80211 xt_time xt_tcpudp xt_multiport xt_mark xt_mac xt_limit xt_comment xt_TCPMSS xt_LOG slhc nf_reject_ipv4 nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 iptable_mangle iptable_filter ip_tables hwmon crc_ccitt compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 leds_gpio gpio_button_hotplug
- [ 19.399957] Process hostapd (pid: 1543, threadinfo=6195646d, task=3c59292f, tls=77e2dec8)
- [ 19.408093] Stack : 86815c00 86814c20 86eff230 86814c20 00000000 86e16e60 86815f80 00000001
- [ 19.416418] 86815f80 86ddb5a0 86815c00 86f49254 00000003 0000145a 00000000 00000000
- [ 19.424742] 00000000 00000000 00100002 00512a24 04010302 00000100 00000003 0000145a
- [ 19.433066] 00000000 00000000 00000000 00000000 86815c00 00000000 00200000 00000001
- [ 19.441389] 00000000 00000000 00000000 00640000 00003802 00000000 0008000f 00000001
- [ 19.449713] ...
- [ 19.452146] Call Trace:
- [ 19.452184] [<86ddb5a0>] 0x86ddb5a0 [mt76_connac_lib@c3ed30b7+0x4e80]
- [ 19.461030] [<86f49254>] 0x86f49254 [mac80211@347a072b+0x7fa40]
- [ 19.466945] [<868014d0>] 0x868014d0 [mt7615_common@09d122ca+0x102a0]
- [ 19.473296] [<86f27bc8>] 0x86f27bc8 [mac80211@347a072b+0x7fa40]
- [ 19.479203] [<86eb7ff8>] 0x86eb7ff8 [cfg80211@bb450c4d+0x44270]
- [ 19.485117] [<86eab3c4>] 0x86eab3c4 [cfg80211@bb450c4d+0x44270]
- [ 19.491013] [<80152fd4>] 0x80152fd4
- [ 19.494486] [<8005c158>] 0x8005c158
- [ 19.498006] [<804a3ccc>] 0x804a3ccc
- [ 19.501505] [<804a3a9c>] 0x804a3a9c
- [ 19.504979] [<804a1a14>] 0x804a1a14
- [ 19.508454] [<804a2258>] 0x804a2258
- [ 19.511926] [<8017424c>] 0x8017424c
- [ 19.515404] [<804a2a4c>] 0x804a2a4c
- [ 19.518886] [<804a1930>] 0x804a1930
- [ 19.522360] [<8017424c>] 0x8017424c
- [ 19.525848] [<804a1d0c>] 0x804a1d0c
- [ 19.529323] [<8017a9e0>] 0x8017a9e0
- [ 19.532797] [<80425a58>] 0x80425a58
- [ 19.536276] [<80410b28>] 0x80410b28
- [ 19.539750] [<80411328>] 0x80411328
- [ 19.543238] [<80411438>] 0x80411438
- [ 19.546709] [<802d1330>] 0x802d1330
- [ 19.550184] [<800707e0>] 0x800707e0
- [ 19.553664] [<800704b4>] 0x800704b4
- [ 19.557160] [<80426628>] 0x80426628
- [ 19.560633] [<804114f0>] 0x804114f0
- [ 19.564101] [<8040f2ac>] 0x8040f2ac
- [ 19.567581] [<801d25f4>] 0x801d25f4
- [ 19.571060] [<80412658>] 0x80412658
- [ 19.574536] [<8040fb1c>] 0x8040fb1c
- [ 19.578017] [<80014558>] 0x80014558
- [ 19.581494]
- [ 19.582974] Code: 10600002 00801025 34820020 <92030000> 1060ffe4 8fbf0024 1000ffe2 34420040 8c840000
- [ 19.592685]
- [ 19.594966] ---[ end trace 05ac765cd135cc09 ]---
- [ 19.599633] Kernel panic - not syncing: Fatal exception
- [ 19.604895] Rebooting in 3 seconds..
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement