API tools faq
paste
Advertisement
tim57064

config h

tim57064
May 21st, 2019
167
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 71.74 KB | None | 0 0
raw download clone embed print report
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22.  
  23. /**
  24. * Configuration.h
  25. *
  26. * Basic settings such as:
  27. *
  28. * - Type of electronics
  29. * - Type of temperature sensor
  30. * - Printer geometry
  31. * - Endstop configuration
  32. * - LCD controller
  33. * - Extra features
  34. *
  35. * Advanced settings can be found in Configuration_adv.h
  36. *
  37. */
  38. #ifndef CONFIGURATION_H
  39. #define CONFIGURATION_H
  40. #define CONFIGURATION_H_VERSION 010109
  41.  
  42. //===========================================================================
  43. //============================= Getting Started =============================
  44. //===========================================================================
  45.  
  46. /**
  47. * Here are some standard links for getting your machine calibrated:
  48. *
  49. * http://reprap.org/wiki/Calibration
  50. * http://youtu.be/wAL9d7FgInk
  51. * http://calculator.josefprusa.cz
  52. * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  53. * http://www.thingiverse.com/thing:5573
  54. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  55. * http://www.thingiverse.com/thing:298812
  56. */
  57.  
  58. //===========================================================================
  59. //============================= DELTA Printer ===============================
  60. //===========================================================================
  61. // For a Delta printer start with one of the configuration files in the
  62. // example_configurations/delta directory and customize for your machine.
  63. //
  64.  
  65. //===========================================================================
  66. //============================= SCARA Printer ===============================
  67. //===========================================================================
  68. // For a SCARA printer start with the configuration files in
  69. // example_configurations/SCARA and customize for your machine.
  70. //
  71.  
  72. // @section info
  73.  
  74. // User-specified version info of this build to display in [Pronterface, etc] terminal window during
  75. // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
  76. // build by the user have been successfully uploaded into firmware.
  77. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
  78. #define SHOW_BOOTSCREEN
  79. #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
  80. #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
  81.  
  82. /**
  83. * *** VENDORS PLEASE READ ***
  84. *
  85. * Marlin allows you to add a custom boot image for Graphical LCDs.
  86. * With this option Marlin will first show your custom screen followed
  87. * by the standard Marlin logo with version number and web URL.
  88. *
  89. * We encourage you to take advantage of this new feature and we also
  90. * respectfully request that you retain the unmodified Marlin boot screen.
  91. */
  92.  
  93. // Enable to show the bitmap in Marlin/_Bootscreen.h on startup.
  94. //#define SHOW_CUSTOM_BOOTSCREEN
  95.  
  96. // Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen.
  97. //#define CUSTOM_STATUS_SCREEN_IMAGE
  98.  
  99. // @section machine
  100.  
  101. /**
  102. * Select the serial port on the board to use for communication with the host.
  103. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  104. * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
  105. *
  106. * :[0, 1, 2, 3, 4, 5, 6, 7]
  107. */
  108. #define SERIAL_PORT 0
  109.  
  110. /**
  111. * This setting determines the communication speed of the printer.
  112. *
  113. * 250000 works in most cases, but you might try a lower speed if
  114. * you commonly experience drop-outs during host printing.
  115. * You may try up to 1000000 to speed up SD file transfer.
  116. *
  117. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  118. */
  119. #define BAUDRATE 250000
  120.  
  121. // Enable the Bluetooth serial interface on AT90USB devices
  122. //#define BLUETOOTH
  123.  
  124. // The following define selects which electronics board you have.
  125. // Please choose the name from boards.h that matches your setup
  126. #ifndef MOTHERBOARD
  127. #define MOTHERBOARD BOARD_MKS_GEN_L
  128. #endif
  129.  
  130. // Optional custom name for your RepStrap or other custom machine
  131. // Displayed in the LCD "Ready" message
  132. #define CUSTOM_MACHINE_NAME "BD3D HYPERCUBE"
  133.  
  134. // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
  135. // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
  136. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  137.  
  138. // @section extruder
  139.  
  140. // This defines the number of extruders
  141. // :[1, 2, 3, 4, 5]
  142. #define EXTRUDERS 1
  143.  
  144. // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
  145. #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
  146.  
  147. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  148. //#define SINGLENOZZLE
  149.  
  150. /**
  151. * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.
  152. *
  153. * This device allows one stepper driver on a control board to drive
  154. * two to eight stepper motors, one at a time, in a manner suitable
  155. * for extruders.
  156. *
  157. * This option only allows the multiplexer to switch on tool-change.
  158. * Additional options to configure custom E moves are pending.
  159. */
  160. //#define MK2_MULTIPLEXER
  161. #if ENABLED(MK2_MULTIPLEXER)
  162. // Override the default DIO selector pins here, if needed.
  163. // Some pins files may provide defaults for these pins.
  164. //#define E_MUX0_PIN 40 // Always Required
  165. //#define E_MUX1_PIN 42 // Needed for 3 to 8 steppers
  166. //#define E_MUX2_PIN 44 // Needed for 5 to 8 steppers
  167. #endif
  168.  
  169. // A dual extruder that uses a single stepper motor
  170. //#define SWITCHING_EXTRUDER
  171. #if ENABLED(SWITCHING_EXTRUDER)
  172. #define SWITCHING_EXTRUDER_SERVO_NR 0
  173. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  174. #if EXTRUDERS > 3
  175. #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  176. #endif
  177. #endif
  178.  
  179. // A dual-nozzle that uses a servomotor to raise/lower one of the nozzles
  180. //#define SWITCHING_NOZZLE
  181. #if ENABLED(SWITCHING_NOZZLE)
  182. #define SWITCHING_NOZZLE_SERVO_NR 0
  183. #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
  184. //#define HOTEND_OFFSET_Z { 0.0, 0.0 }
  185. #endif
  186.  
  187. /**
  188. * Two separate X-carriages with extruders that connect to a moving part
  189. * via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  190. */
  191. //#define PARKING_EXTRUDER
  192. #if ENABLED(PARKING_EXTRUDER)
  193. #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
  194. #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
  195. #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
  196. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
  197. #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
  198. #define PARKING_EXTRUDER_SECURITY_RAISE 5 // Z-raise before parking
  199. #define HOTEND_OFFSET_Z { 0.0, 1.3 } // Z-offsets of the two hotends. The first must be 0.
  200. #endif
  201.  
  202. /**
  203. * "Mixing Extruder"
  204. * - Adds a new code, M165, to set the current mix factors.
  205. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  206. * - Optional support for Repetier Firmware M163, M164, and virtual extruder.
  207. * - This implementation supports only a single extruder.
  208. * - Enable DIRECT_MIXING_IN_G1 for Pia Taubert's reference implementation
  209. */
  210. //#define MIXING_EXTRUDER
  211. #if ENABLED(MIXING_EXTRUDER)
  212. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  213. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  214. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  215. #endif
  216.  
  217. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  218. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  219. // For the other hotends it is their distance from the extruder 0 hotend.
  220. //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
  221. //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
  222.  
  223. // @section machine
  224.  
  225. /**
  226. * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
  227. *
  228. * 0 = No Power Switch
  229. * 1 = ATX
  230. * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
  231. *
  232. * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
  233. */
  234. #define POWER_SUPPLY 0
  235.  
  236. #if POWER_SUPPLY > 0
  237. // Enable this option to leave the PSU off at startup.
  238. // Power to steppers and heaters will need to be turned on with M80.
  239. //#define PS_DEFAULT_OFF
  240.  
  241. //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin
  242. #if ENABLED(AUTO_POWER_CONTROL)
  243. #define AUTO_POWER_FANS // Turn on PSU if fans need power
  244. #define AUTO_POWER_E_FANS
  245. #define AUTO_POWER_CONTROLLERFAN
  246. #define POWER_TIMEOUT 30
  247. #endif
  248.  
  249. #endif
  250.  
  251. // @section temperature
  252.  
  253. //===========================================================================
  254. //============================= Thermal Settings ============================
  255. //===========================================================================
  256.  
  257. /**
  258. * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  259. *
  260. * Temperature sensors available:
  261. *
  262. * -4 : thermocouple with AD8495
  263. * -3 : thermocouple with MAX31855 (only for sensor 0)
  264. * -2 : thermocouple with MAX6675 (only for sensor 0)
  265. * -1 : thermocouple with AD595
  266. * 0 : not used
  267. * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  268. * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  269. * 3 : Mendel-parts thermistor (4.7k pullup)
  270. * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  271. * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup)
  272. * 501 : 100K Zonestar (Tronxy X3A) Thermistor
  273. * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  274. * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  275. * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  276. * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  277. * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  278. * 10 : 100k RS thermistor 198-961 (4.7k pullup)
  279. * 11 : 100k beta 3950 1% thermistor (4.7k pullup)
  280. * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  281. * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  282. * 15 : 100k thermistor calibration for JGAurora A5 hotend
  283. * 20 : the PT100 circuit found in the Ultimainboard V2.x
  284. * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  285. * 66 : 4.7M High Temperature thermistor from Dyze Design
  286. * 70 : the 100K thermistor found in the bq Hephestos 2
  287. * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
  288. *
  289. * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  290. * (but gives greater accuracy and more stable PID)
  291. * 51 : 100k thermistor - EPCOS (1k pullup)
  292. * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  293. * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  294. *
  295. * 1047 : Pt1000 with 4k7 pullup
  296. * 1010 : Pt1000 with 1k pullup (non standard)
  297. * 147 : Pt100 with 4k7 pullup
  298. * 110 : Pt100 with 1k pullup (non standard)
  299. *
  300. * Use these for Testing or Development purposes. NEVER for production machine.
  301. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  302. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  303. *
  304. * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
  305. */
  306. #define TEMP_SENSOR_0 1
  307. #define TEMP_SENSOR_1 0
  308. #define TEMP_SENSOR_2 0
  309. #define TEMP_SENSOR_3 0
  310. #define TEMP_SENSOR_4 0
  311. #define TEMP_SENSOR_BED 1
  312. #define TEMP_SENSOR_CHAMBER 0
  313.  
  314. // Dummy thermistor constant temperature readings, for use with 998 and 999
  315. #define DUMMY_THERMISTOR_998_VALUE 25
  316. #define DUMMY_THERMISTOR_999_VALUE 100
  317.  
  318. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  319. // from the two sensors differ too much the print will be aborted.
  320. //#define TEMP_SENSOR_1_AS_REDUNDANT
  321. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  322.  
  323. // Extruder temperature must be close to target for this long before M109 returns success
  324. #define TEMP_RESIDENCY_TIME 10 // (seconds)
  325. #define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  326. #define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  327.  
  328. // Bed temperature must be close to target for this long before M190 returns success
  329. #define TEMP_BED_RESIDENCY_TIME 10 // (seconds)
  330. #define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  331. #define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  332.  
  333. // The minimal temperature defines the temperature below which the heater will not be enabled It is used
  334. // to check that the wiring to the thermistor is not broken.
  335. // Otherwise this would lead to the heater being powered on all the time.
  336. #define HEATER_0_MINTEMP 5
  337. #define HEATER_1_MINTEMP 5
  338. #define HEATER_2_MINTEMP 5
  339. #define HEATER_3_MINTEMP 5
  340. #define HEATER_4_MINTEMP 5
  341. #define BED_MINTEMP 5
  342.  
  343. // When temperature exceeds max temp, your heater will be switched off.
  344. // This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
  345. // You should use MINTEMP for thermistor short/failure protection.
  346. #define HEATER_0_MAXTEMP 275
  347. #define HEATER_1_MAXTEMP 275
  348. #define HEATER_2_MAXTEMP 275
  349. #define HEATER_3_MAXTEMP 275
  350. #define HEATER_4_MAXTEMP 275
  351. #define BED_MAXTEMP 120
  352.  
  353. //===========================================================================
  354. //============================= PID Settings ================================
  355. //===========================================================================
  356. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  357.  
  358. // Comment the following line to disable PID and enable bang-bang.
  359. #define PIDTEMP
  360. #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current
  361. #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  362. #define PID_K1 0.95 // Smoothing factor within any PID loop
  363. #if ENABLED(PIDTEMP)
  364. //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
  365. //#define PID_DEBUG // Sends debug data to the serial port.
  366. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  367. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  368. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  369. // Set/get with gcode: M301 E[extruder number, 0-2]
  370. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  371. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  372.  
  373. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  374.  
  375. // Ultimaker
  376. #define DEFAULT_Kp 22.2
  377. #define DEFAULT_Ki 1.08
  378. #define DEFAULT_Kd 114
  379.  
  380. // MakerGear
  381. //#define DEFAULT_Kp 7.0
  382. //#define DEFAULT_Ki 0.1
  383. //#define DEFAULT_Kd 12
  384.  
  385. // Mendel Parts V9 on 12V
  386. //#define DEFAULT_Kp 63.0
  387. //#define DEFAULT_Ki 2.25
  388. //#define DEFAULT_Kd 440
  389.  
  390. #endif // PIDTEMP
  391.  
  392. //===========================================================================
  393. //============================= PID > Bed Temperature Control ===============
  394. //===========================================================================
  395.  
  396. /**
  397. * PID Bed Heating
  398. *
  399. * If this option is enabled set PID constants below.
  400. * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
  401. *
  402. * The PID frequency will be the same as the extruder PWM.
  403. * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
  404. * which is fine for driving a square wave into a resistive load and does not significantly
  405. * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
  406. * heater. If your configuration is significantly different than this and you don't understand
  407. * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  408. */
  409. //#define PIDTEMPBED
  410.  
  411. //#define BED_LIMIT_SWITCHING
  412.  
  413. /**
  414. * Max Bed Power
  415. * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
  416. * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
  417. * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
  418. */
  419. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  420.  
  421. #if ENABLED(PIDTEMPBED)
  422.  
  423. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  424.  
  425. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  426. //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  427. #define DEFAULT_bedKp 10.00
  428. #define DEFAULT_bedKi .023
  429. #define DEFAULT_bedKd 305.4
  430.  
  431. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  432. //from pidautotune
  433. //#define DEFAULT_bedKp 97.1
  434. //#define DEFAULT_bedKi 1.41
  435. //#define DEFAULT_bedKd 1675.16
  436.  
  437. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  438. #endif // PIDTEMPBED
  439.  
  440. // @section extruder
  441.  
  442. /**
  443. * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
  444. * Add M302 to set the minimum extrusion temperature and/or turn
  445. * cold extrusion prevention on and off.
  446. *
  447. * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  448. */
  449. #define PREVENT_COLD_EXTRUSION
  450. #define EXTRUDE_MINTEMP 170
  451.  
  452. /**
  453. * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
  454. * Note: For Bowden Extruders make this large enough to allow load/unload.
  455. */
  456. #define PREVENT_LENGTHY_EXTRUDE
  457. #define EXTRUDE_MAXLENGTH 200
  458.  
  459. //===========================================================================
  460. //======================== Thermal Runaway Protection =======================
  461. //===========================================================================
  462.  
  463. /**
  464. * Thermal Protection provides additional protection to your printer from damage
  465. * and fire. Marlin always includes safe min and max temperature ranges which
  466. * protect against a broken or disconnected thermistor wire.
  467. *
  468. * The issue: If a thermistor falls out, it will report the much lower
  469. * temperature of the air in the room, and the the firmware will keep
  470. * the heater on.
  471. *
  472. * If you get "Thermal Runaway" or "Heating failed" errors the
  473. * details can be tuned in Configuration_adv.h
  474. */
  475.  
  476. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  477. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  478.  
  479. //===========================================================================
  480. //============================= Mechanical Settings =========================
  481. //===========================================================================
  482.  
  483. // @section machine
  484.  
  485. // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
  486. // either in the usual order or reversed
  487. #define COREXY
  488. //#define COREXZ
  489. //#define COREYZ
  490. //#define COREYX
  491. //#define COREZX
  492. //#define COREZY
  493.  
  494. //===========================================================================
  495. //============================== Endstop Settings ===========================
  496. //===========================================================================
  497.  
  498. // @section homing
  499.  
  500. // Specify here all the endstop connectors that are connected to any endstop or probe.
  501. // Almost all printers will be using one per axis. Probes will use one or more of the
  502. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  503. #define USE_XMIN_PLUG
  504. #define USE_YMIN_PLUG
  505. #define USE_ZMIN_PLUG
  506. //#define USE_XMAX_PLUG
  507. //#define USE_YMAX_PLUG
  508. //#define USE_ZMAX_PLUG
  509.  
  510. //Enable pullup for all endstops to prevent a floating state
  511. //#define ENDSTOPPULLUPS
  512. #if DISABLED(ENDSTOPPULLUPS)
  513. // Disable ENDSTOPPULLUPS to set pullups individually
  514. //#define ENDSTOPPULLUP_XMAX
  515. //#define ENDSTOPPULLUP_YMAX
  516. //#define ENDSTOPPULLUP_ZMAX
  517. #define ENDSTOPPULLUP_XMIN
  518. #define ENDSTOPPULLUP_YMIN
  519. #define ENDSTOPPULLUP_ZMIN
  520. #define ENDSTOPPULLUP_ZMIN_PROBE
  521. #endif
  522.  
  523. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  524. #define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  525. #define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  526. #define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  527. #define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  528. #define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  529. #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  530. #define Z_MIN_PROBE_ENDSTOP_INVERTING true// set to true to invert the logic of the probe.
  531.  
  532. /**
  533. * Specify Stepper Driver types
  534. * The options are used to determine driver pulse timings as well as more advanced functionality.
  535. * Stepper timing options can be overridden in Configuration_adv.h
  536. *
  537. * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
  538. * TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
  539. * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
  540. * TMC5130, TMC5130_STANDALONE
  541. * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
  542. */
  543. #define X_DRIVER_TYPE LV8729
  544. #define Y_DRIVER_TYPE LV8729
  545. #define Z_DRIVER_TYPE LV8729
  546. #define X2_DRIVER_TYPE LV8729
  547. #define Y2_DRIVER_TYPE LV8729
  548. #define Z2_DRIVER_TYPE LV8729
  549. #define E0_DRIVER_TYPE LV8729
  550. #define E1_DRIVER_TYPE LV8729
  551. #define E2_DRIVER_TYPE LV8729
  552. #define E3_DRIVER_TYPE LV8729
  553. #define E4_DRIVER_TYPE LV8729
  554.  
  555. // Enable this feature if all enabled endstop pins are interrupt-capable.
  556. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  557. //#define ENDSTOP_INTERRUPTS_FEATURE
  558.  
  559. /**
  560. * Endstop Noise Filter
  561. *
  562. * Enable this option if endstops falsely trigger due to noise.
  563. * NOTE: Enabling this feature means adds an error of +/-0.2mm, so homing
  564. * will end up at a slightly different position on each G28. This will also
  565. * reduce accuracy of some bed probes.
  566. * For mechanical switches, the better approach to reduce noise is to install
  567. * a 100 nanofarads ceramic capacitor in parallel with the switch, making it
  568. * essentially noise-proof without sacrificing accuracy.
  569. * This option also increases MCU load when endstops or the probe are enabled.
  570. * So this is not recommended. USE AT YOUR OWN RISK.
  571. * (This feature is not required for common micro-switches mounted on PCBs
  572. * based on the Makerbot design, since they already include the 100nF capacitor.)
  573. */
  574. //#define ENDSTOP_NOISE_FILTER
  575.  
  576. //=============================================================================
  577. //============================== Movement Settings ============================
  578. //=============================================================================
  579. // @section motion
  580.  
  581. /**
  582. * Default Settings
  583. *
  584. * These settings can be reset by M502
  585. *
  586. * Note that if EEPROM is enabled, saved values will override these.
  587. */
  588.  
  589. /**
  590. * With this option each E stepper can have its own factors for the
  591. * following movement settings. If fewer factors are given than the
  592. * total number of extruders, the last value applies to the rest.
  593. */
  594. //#define DISTINCT_E_FACTORS
  595.  
  596. /**
  597. * Default Axis Steps Per Unit (steps/mm)
  598. * Override with M92
  599. * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  600. */
  601. #define DEFAULT_AXIS_STEPS_PER_UNIT { 630, 630, 1680, 810 }
  602.  
  603. /**
  604. * Default Max Feed Rate (mm/s)
  605. * Override with M203
  606. * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  607. */
  608. #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
  609.  
  610. /**
  611. * Default Max Acceleration (change/s) change = mm/s
  612. * (Maximum start speed for accelerated moves)
  613. * Override with M201
  614. * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  615. */
  616. #define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
  617.  
  618. /**
  619. * Default Acceleration (change/s) change = mm/s
  620. * Override with M204
  621. *
  622. * M204 P Acceleration
  623. * M204 R Retract Acceleration
  624. * M204 T Travel Acceleration
  625. */
  626. #define DEFAULT_ACCELERATION 2000 // X, Y, Z and E acceleration for printing moves
  627. #define DEFAULT_RETRACT_ACCELERATION 2000 // E acceleration for retracts
  628. #define DEFAULT_TRAVEL_ACCELERATION 2000 // X, Y, Z acceleration for travel (non printing) moves
  629.  
  630. /**
  631. * Default Jerk (mm/s)
  632. * Override with M205 X Y Z E
  633. *
  634. * "Jerk" specifies the minimum speed change that requires acceleration.
  635. * When changing speed and direction, if the difference is less than the
  636. * value set here, it may happen instantaneously.
  637. */
  638. #define DEFAULT_XJERK 10.0
  639. #define DEFAULT_YJERK 10.0
  640. #define DEFAULT_ZJERK 0.3
  641. #define DEFAULT_EJERK 3.0
  642.  
  643. /**
  644. * S-Curve Acceleration
  645. *
  646. * This option eliminates vibration during printing by fitting a Bézier
  647. * curve to move acceleration, producing much smoother direction changes.
  648. *
  649. * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  650. */
  651. //#define S_CURVE_ACCELERATION
  652.  
  653. //===========================================================================
  654. //============================= Z Probe Options =============================
  655. //===========================================================================
  656. // @section probes
  657.  
  658. //
  659. // See http://marlinfw.org/docs/configuration/probes.html
  660. //
  661.  
  662. /**
  663. * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  664. *
  665. * Enable this option for a probe connected to the Z Min endstop pin.
  666. */
  667. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  668.  
  669. /**
  670. * Z_MIN_PROBE_ENDSTOP
  671. *
  672. * Enable this option for a probe connected to any pin except Z-Min.
  673. * (By default Marlin assumes the Z-Max endstop pin.)
  674. * To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
  675. *
  676. * - The simplest option is to use a free endstop connector.
  677. * - Use 5V for powered (usually inductive) sensors.
  678. *
  679. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  680. * - For simple switches connect...
  681. * - normally-closed switches to GND and D32.
  682. * - normally-open switches to 5V and D32.
  683. *
  684. * WARNING: Setting the wrong pin may have unexpected and potentially
  685. * disastrous consequences. Use with caution and do your homework.
  686. *
  687. */
  688. //#define Z_MIN_PROBE_ENDSTOP
  689.  
  690. /**
  691. * Probe Type
  692. *
  693. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  694. * Activate one of these to use Auto Bed Leveling below.
  695. */
  696.  
  697. /**
  698. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  699. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  700. * or (with LCD_BED_LEVELING) the LCD controller.
  701. */
  702. //#define PROBE_MANUALLY
  703. //#define MANUAL_PROBE_START_Z 0.2
  704.  
  705. /**
  706. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  707. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  708. */
  709. //#define FIX_MOUNTED_PROBE
  710.  
  711. /**
  712. * Z Servo Probe, such as an endstop switch on a rotating arm.
  713. */
  714. //#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.
  715. //#define Z_SERVO_ANGLES {10,90} // Z Servo Deploy and Stow angles
  716.  
  717. /**
  718. * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  719. */
  720. #define BLTOUCH
  721. #if ENABLED(BLTOUCH)
  722. //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed
  723. #endif
  724.  
  725. /**
  726. * Enable one or more of the following if probing seems unreliable.
  727. * Heaters and/or fans can be disabled during probing to minimize electrical
  728. * noise. A delay can also be added to allow noise and vibration to settle.
  729. * These options are most useful for the BLTouch probe, but may also improve
  730. * readings with inductive probes and piezo sensors.
  731. */
  732. //#define PROBING_HEATERS_OFF // Turn heaters off when probing
  733. #if ENABLED(PROBING_HEATERS_OFF)
  734. //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
  735. #endif
  736. //#define PROBING_FANS_OFF // Turn fans off when probing
  737. //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
  738.  
  739. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  740. //#define SOLENOID_PROBE
  741.  
  742. // A sled-mounted probe like those designed by Charles Bell.
  743. //#define Z_PROBE_SLED
  744. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  745.  
  746. //
  747. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  748. //
  749.  
  750. /**
  751. * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  752. * X and Y offsets must be integers.
  753. *
  754. * In the following example the X and Y offsets are both positive:
  755. * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
  756. * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
  757. *
  758. * +-- BACK ---+
  759. * | |
  760. * L | (+) P | R <-- probe (20,20)
  761. * E | | I
  762. * F | (-) N (+) | G <-- nozzle (10,10)
  763. * T | | H
  764. * | (-) | T
  765. * | |
  766. * O-- FRONT --+
  767. * (0,0)
  768. */
  769. #define X_PROBE_OFFSET_FROM_EXTRUDER 30 // X offset: -left +right [of the nozzle]
  770. #define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]
  771. #define Z_PROBE_OFFSET_FROM_EXTRUDER 0
  772. // Z offset: -below +above [the nozzle]
  773.  
  774. // Certain types of probes need to stay away from edges
  775. #define MIN_PROBE_EDGE 20
  776.  
  777. // X and Y axis travel speed (mm/m) between probes
  778. #define XY_PROBE_SPEED 8000
  779.  
  780. // Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
  781. #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
  782.  
  783. // Feedrate (mm/m) for the "accurate" probe of each point
  784. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
  785.  
  786. // The number of probes to perform at each point.
  787. // Set to 2 for a fast/slow probe, using the second probe result.
  788. // Set to 3 or more for slow probes, averaging the results.
  789. //#define MULTIPLE_PROBING 2
  790.  
  791. /**
  792. * Z probes require clearance when deploying, stowing, and moving between
  793. * probe points to avoid hitting the bed and other hardware.
  794. * Servo-mounted probes require extra space for the arm to rotate.
  795. * Inductive probes need space to keep from triggering early.
  796. *
  797. * Use these settings to specify the distance (mm) to raise the probe (or
  798. * lower the bed). The values set here apply over and above any (negative)
  799. * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
  800. * Only integer values >= 1 are valid here.
  801. *
  802. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  803. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  804. */
  805. #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
  806. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  807. #define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
  808. //#define Z_AFTER_PROBING 5 // Z position after probing is done
  809.  
  810. #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
  811.  
  812. // For M851 give a range for adjusting the Z probe offset
  813. #define Z_PROBE_OFFSET_RANGE_MIN -20
  814. #define Z_PROBE_OFFSET_RANGE_MAX 20
  815.  
  816. // Enable the M48 repeatability test to test probe accuracy
  817. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  818.  
  819. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  820. // :{ 0:'Low', 1:'High' }
  821. #define X_ENABLE_ON 0
  822. #define Y_ENABLE_ON 0
  823. #define Z_ENABLE_ON 0
  824. #define E_ENABLE_ON 0 // For all extruders
  825.  
  826. // Disables axis stepper immediately when it's not being used.
  827. // WARNING: When motors turn off there is a chance of losing position accuracy!
  828. #define DISABLE_X false
  829. #define DISABLE_Y false
  830. #define DISABLE_Z false
  831. // Warn on display about possibly reduced accuracy
  832. //#define DISABLE_REDUCED_ACCURACY_WARNING
  833.  
  834. // @section extruder
  835.  
  836. #define DISABLE_E false // For all extruders
  837. #define DISABLE_INACTIVE_EXTRUDER true // Keep only the active extruder enabled.
  838.  
  839. // @section machine
  840.  
  841. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  842. #define INVERT_X_DIR false
  843. #define INVERT_Y_DIR false
  844. #define INVERT_Z_DIR false
  845.  
  846. // @section extruder
  847.  
  848. // For direct drive extruder v9 set to true, for geared extruder set to false.
  849. #define INVERT_E0_DIR false
  850. #define INVERT_E1_DIR true
  851. #define INVERT_E2_DIR false
  852. #define INVERT_E3_DIR false
  853. #define INVERT_E4_DIR false
  854.  
  855. // @section homing
  856.  
  857. //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
  858.  
  859. //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
  860.  
  861. //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
  862. // Be sure you have this distance over your Z_MAX_POS in case.
  863.  
  864. // Direction of endstops when homing; 1=MAX, -1=MIN
  865. // :[-1,1]
  866. #define X_HOME_DIR -1
  867. #define Y_HOME_DIR -1
  868. #define Z_HOME_DIR -1
  869.  
  870. // @section machine
  871.  
  872. // The size of the print bed
  873. #define X_BED_SIZE 400
  874. #define Y_BED_SIZE 400
  875.  
  876. // Travel limits (mm) after homing, corresponding to endstop positions.
  877. #define X_MIN_POS 0
  878. #define Y_MIN_POS 0
  879. #define Z_MIN_POS 0
  880. #define X_MAX_POS X_BED_SIZE
  881. #define Y_MAX_POS Y_BED_SIZE
  882. #define Z_MAX_POS 500
  883.  
  884. /**
  885. * Software Endstops
  886. *
  887. * - Prevent moves outside the set machine bounds.
  888. * - Individual axes can be disabled, if desired.
  889. * - X and Y only apply to Cartesian robots.
  890. * - Use 'M211' to set software endstops on/off or report current state
  891. */
  892.  
  893. // Min software endstops constrain movement within minimum coordinate bounds
  894. #define MIN_SOFTWARE_ENDSTOPS
  895. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  896. #define MIN_SOFTWARE_ENDSTOP_X
  897. #define MIN_SOFTWARE_ENDSTOP_Y
  898. //#define MIN_SOFTWARE_ENDSTOP_Z
  899. #endif
  900.  
  901. // Max software endstops constrain movement within maximum coordinate bounds
  902. #define MAX_SOFTWARE_ENDSTOPS
  903. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  904. #define MAX_SOFTWARE_ENDSTOP_X
  905. #define MAX_SOFTWARE_ENDSTOP_Y
  906. #define MAX_SOFTWARE_ENDSTOP_Z
  907. #endif
  908.  
  909. #if ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS)
  910. //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
  911. #endif
  912.  
  913. /**
  914. * Filament Runout Sensors
  915. * Mechanical or opto endstops are used to check for the presence of filament.
  916. *
  917. * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  918. * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  919. * By default the firmware assumes HIGH=FILAMENT PRESENT.
  920. */
  921. //#define FILAMENT_RUNOUT_SENSOR
  922. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  923. #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
  924. #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
  925. #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
  926. #define FILAMENT_RUNOUT_SCRIPT "M600"
  927. #endif
  928.  
  929. //===========================================================================
  930. //=============================== Bed Leveling ==============================
  931. //===========================================================================
  932. // @section calibrate
  933.  
  934. /**
  935. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  936. * and behavior of G29 will change depending on your selection.
  937. *
  938. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  939. *
  940. * - AUTO_BED_LEVELING_3POINT
  941. * Probe 3 arbitrary points on the bed (that aren't collinear)
  942. * You specify the XY coordinates of all 3 points.
  943. * The result is a single tilted plane. Best for a flat bed.
  944. *
  945. * - AUTO_BED_LEVELING_LINEAR
  946. * Probe several points in a grid.
  947. * You specify the rectangle and the density of sample points.
  948. * The result is a single tilted plane. Best for a flat bed.
  949. *
  950. * - AUTO_BED_LEVELING_BILINEAR
  951. * Probe several points in a grid.
  952. * You specify the rectangle and the density of sample points.
  953. * The result is a mesh, best for large or uneven beds.
  954. *
  955. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  956. * A comprehensive bed leveling system combining the features and benefits
  957. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  958. * Validation and Mesh Editing systems.
  959. *
  960. * - MESH_BED_LEVELING
  961. * Probe a grid manually
  962. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  963. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  964. * leveling in steps so you can manually adjust the Z height at each grid-point.
  965. * With an LCD controller the process is guided step-by-step.
  966. */
  967. //#define AUTO_BED_LEVELING_3POINT
  968. //#define AUTO_BED_LEVELING_LINEAR
  969. #define AUTO_BED_LEVELING_BILINEAR
  970. //#define AUTO_BED_LEVELING_UBL
  971. //#define MESH_BED_LEVELING
  972.  
  973. /**
  974. * Normally G28 leaves leveling disabled on completion. Enable
  975. * this option to have G28 restore the prior leveling state.
  976. */
  977. //#define RESTORE_LEVELING_AFTER_G28
  978.  
  979. /**
  980. * Enable detailed logging of G28, G29, M48, etc.
  981. * Turn on with the command 'M111 S32'.
  982. * NOTE: Requires a lot of PROGMEM!
  983. */
  984. //#define DEBUG_LEVELING_FEATURE
  985.  
  986. #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
  987. // Gradually reduce leveling correction until a set height is reached,
  988. // at which point movement will be level to the machine's XY plane.
  989. // The height can be set with M420 Z<height>
  990. #define ENABLE_LEVELING_FADE_HEIGHT
  991.  
  992. // For Cartesian machines, instead of dividing moves on mesh boundaries,
  993. // split up moves into short segments like a Delta. This follows the
  994. // contours of the bed more closely than edge-to-edge straight moves.
  995. #define SEGMENT_LEVELED_MOVES
  996. #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
  997.  
  998. /**
  999. * Enable the G26 Mesh Validation Pattern tool.
  1000. */
  1001. //#define G26_MESH_VALIDATION
  1002. #if ENABLED(G26_MESH_VALIDATION)
  1003. #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
  1004. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
  1005. #define MESH_TEST_HOTEND_TEMP 205.0 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
  1006. #define MESH_TEST_BED_TEMP 60.0 // (°C) Default bed temperature for the G26 Mesh Validation Tool.
  1007. #endif
  1008.  
  1009. #endif
  1010.  
  1011. #if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)
  1012.  
  1013. // Set the number of grid points per dimension.
  1014. #define GRID_MAX_POINTS_X 5
  1015. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1016.  
  1017. // Set the boundaries for probing (where the probe can reach).
  1018. //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
  1019. //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - MIN_PROBE_EDGE)
  1020. //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
  1021. //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - MIN_PROBE_EDGE)
  1022.  
  1023. // Probe along the Y axis, advancing X after each column
  1024. //#define PROBE_Y_FIRST
  1025.  
  1026. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  1027.  
  1028. // Beyond the probed grid, continue the implied tilt?
  1029. // Default is to maintain the height of the nearest edge.
  1030. //#define EXTRAPOLATE_BEYOND_GRID
  1031.  
  1032. //
  1033. // Experimental Subdivision of the grid by Catmull-Rom method.
  1034. // Synthesizes intermediate points to produce a more detailed mesh.
  1035. //
  1036. //#define ABL_BILINEAR_SUBDIVISION
  1037. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  1038. // Number of subdivisions between probe points
  1039. #define BILINEAR_SUBDIVISIONS 3
  1040. #endif
  1041.  
  1042. #endif
  1043.  
  1044. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  1045.  
  1046. //===========================================================================
  1047. //========================= Unified Bed Leveling ============================
  1048. //===========================================================================
  1049.  
  1050. //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
  1051.  
  1052. #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
  1053. #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
  1054. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1055.  
  1056. #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
  1057. #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
  1058.  
  1059. //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
  1060. // as the Z-Height correction value.
  1061.  
  1062. #elif ENABLED(MESH_BED_LEVELING)
  1063.  
  1064. //===========================================================================
  1065. //=================================== Mesh ==================================
  1066. //===========================================================================
  1067.  
  1068. #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
  1069. #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
  1070. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1071.  
  1072. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  1073.  
  1074. #endif // BED_LEVELING
  1075.  
  1076. /**
  1077. * Points to probe for all 3-point Leveling procedures.
  1078. * Override if the automatically selected points are inadequate.
  1079. */
  1080. #if ENABLED(AUTO_BED_LEVELING_3POINT) || ENABLED(AUTO_BED_LEVELING_UBL)
  1081. //#define PROBE_PT_1_X 15
  1082. //#define PROBE_PT_1_Y 180
  1083. //#define PROBE_PT_2_X 15
  1084. //#define PROBE_PT_2_Y 20
  1085. //#define PROBE_PT_3_X 170
  1086. //#define PROBE_PT_3_Y 20
  1087. #endif
  1088.  
  1089. /**
  1090. * Add a bed leveling sub-menu for ABL or MBL.
  1091. * Include a guided procedure if manual probing is enabled.
  1092. */
  1093. //#define LCD_BED_LEVELING
  1094.  
  1095. #if ENABLED(LCD_BED_LEVELING)
  1096. #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
  1097. #define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
  1098. #endif
  1099.  
  1100. // Add a menu item to move between bed corners for manual bed adjustment
  1101. //#define LEVEL_BED_CORNERS
  1102.  
  1103. #if ENABLED(LEVEL_BED_CORNERS)
  1104. #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
  1105. //#define LEVEL_CENTER_TOO // Move to the center after the last corner
  1106. #endif
  1107.  
  1108. /**
  1109. * Commands to execute at the end of G29 probing.
  1110. * Useful to retract or move the Z probe out of the way.
  1111. */
  1112. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  1113.  
  1114.  
  1115. // @section homing
  1116.  
  1117. // The center of the bed is at (X=0, Y=0)
  1118. //#define BED_CENTER_AT_0_0
  1119.  
  1120. // Manually set the home position. Leave these undefined for automatic settings.
  1121. // For DELTA this is the top-center of the Cartesian print volume.
  1122. //#define MANUAL_X_HOME_POS 0
  1123. //#define MANUAL_Y_HOME_POS 0
  1124. //#define MANUAL_Z_HOME_POS 0
  1125.  
  1126. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  1127. //
  1128. // With this feature enabled:
  1129. //
  1130. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  1131. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  1132. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
  1133. // - Prevent Z homing when the Z probe is outside bed area.
  1134. //
  1135. //#define Z_SAFE_HOMING
  1136.  
  1137. #if ENABLED(Z_SAFE_HOMING)
  1138. #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28).
  1139. #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28).
  1140. #endif
  1141.  
  1142. // Homing speeds (mm/m)
  1143. #define HOMING_FEEDRATE_XY (50*60)
  1144. #define HOMING_FEEDRATE_Z (4*60)
  1145.  
  1146. // @section calibrate
  1147.  
  1148. /**
  1149. * Bed Skew Compensation
  1150. *
  1151. * This feature corrects for misalignment in the XYZ axes.
  1152. *
  1153. * Take the following steps to get the bed skew in the XY plane:
  1154. * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
  1155. * 2. For XY_DIAG_AC measure the diagonal A to C
  1156. * 3. For XY_DIAG_BD measure the diagonal B to D
  1157. * 4. For XY_SIDE_AD measure the edge A to D
  1158. *
  1159. * Marlin automatically computes skew factors from these measurements.
  1160. * Skew factors may also be computed and set manually:
  1161. *
  1162. * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
  1163. * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
  1164. *
  1165. * If desired, follow the same procedure for XZ and YZ.
  1166. * Use these diagrams for reference:
  1167. *
  1168. * Y Z Z
  1169. * ^ B-------C ^ B-------C ^ B-------C
  1170. * | / / | / / | / /
  1171. * | / / | / / | / /
  1172. * | A-------D | A-------D | A-------D
  1173. * +-------------->X +-------------->X +-------------->Y
  1174. * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR
  1175. */
  1176. //#define SKEW_CORRECTION
  1177.  
  1178. #if ENABLED(SKEW_CORRECTION)
  1179. // Input all length measurements here:
  1180. #define XY_DIAG_AC 282.8427124746
  1181. #define XY_DIAG_BD 282.8427124746
  1182. #define XY_SIDE_AD 200
  1183.  
  1184. // Or, set the default skew factors directly here
  1185. // to override the above measurements:
  1186. #define XY_SKEW_FACTOR 0.0
  1187.  
  1188. //#define SKEW_CORRECTION_FOR_Z
  1189. #if ENABLED(SKEW_CORRECTION_FOR_Z)
  1190. #define XZ_DIAG_AC 282.8427124746
  1191. #define XZ_DIAG_BD 282.8427124746
  1192. #define YZ_DIAG_AC 282.8427124746
  1193. #define YZ_DIAG_BD 282.8427124746
  1194. #define YZ_SIDE_AD 200
  1195. #define XZ_SKEW_FACTOR 0.0
  1196. #define YZ_SKEW_FACTOR 0.0
  1197. #endif
  1198.  
  1199. // Enable this option for M852 to set skew at runtime
  1200. //#define SKEW_CORRECTION_GCODE
  1201. #endif
  1202.  
  1203. //=============================================================================
  1204. //============================= Additional Features ===========================
  1205. //=============================================================================
  1206.  
  1207. // @section extras
  1208.  
  1209. //
  1210. // EEPROM
  1211. //
  1212. // The microcontroller can store settings in the EEPROM, e.g. max velocity...
  1213. // M500 - stores parameters in EEPROM
  1214. // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
  1215. // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
  1216. //
  1217. #define EEPROM_SETTINGS // Enable for M500 and M501 commands
  1218. //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
  1219. #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
  1220.  
  1221. //
  1222. // Host Keepalive
  1223. //
  1224. // When enabled Marlin will send a busy status message to the host
  1225. // every couple of seconds when it can't accept commands.
  1226. //
  1227. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  1228. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  1229. #define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
  1230.  
  1231. //
  1232. // M100 Free Memory Watcher
  1233. //
  1234. //#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage
  1235.  
  1236. //
  1237. // G20/G21 Inch mode support
  1238. //
  1239. //#define INCH_MODE_SUPPORT
  1240.  
  1241. //
  1242. // M149 Set temperature units support
  1243. //
  1244. //#define TEMPERATURE_UNITS_SUPPORT
  1245.  
  1246. // @section temperature
  1247.  
  1248. // Preheat Constants
  1249. #define PREHEAT_1_TEMP_HOTEND 210
  1250. #define PREHEAT_1_TEMP_BED 60
  1251. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  1252.  
  1253. #define PREHEAT_2_TEMP_HOTEND 240
  1254. #define PREHEAT_2_TEMP_BED 110
  1255. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  1256.  
  1257. /**
  1258. * Nozzle Park
  1259. *
  1260. * Park the nozzle at the given XYZ position on idle or G27.
  1261. *
  1262. * The "P" parameter controls the action applied to the Z axis:
  1263. *
  1264. * P0 (Default) If Z is below park Z raise the nozzle.
  1265. * P1 Raise the nozzle always to Z-park height.
  1266. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  1267. */
  1268. //#define NOZZLE_PARK_FEATURE
  1269.  
  1270. #if ENABLED(NOZZLE_PARK_FEATURE)
  1271. // Specify a park position as { X, Y, Z }
  1272. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  1273. #define NOZZLE_PARK_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
  1274. #define NOZZLE_PARK_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
  1275. #endif
  1276.  
  1277. /**
  1278. * Clean Nozzle Feature -- EXPERIMENTAL
  1279. *
  1280. * Adds the G12 command to perform a nozzle cleaning process.
  1281. *
  1282. * Parameters:
  1283. * P Pattern
  1284. * S Strokes / Repetitions
  1285. * T Triangles (P1 only)
  1286. *
  1287. * Patterns:
  1288. * P0 Straight line (default). This process requires a sponge type material
  1289. * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  1290. * between the start / end points.
  1291. *
  1292. * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  1293. * number of zig-zag triangles to do. "S" defines the number of strokes.
  1294. * Zig-zags are done in whichever is the narrower dimension.
  1295. * For example, "G12 P1 S1 T3" will execute:
  1296. *
  1297. * --
  1298. * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  1299. * | | / \ / \ / \ |
  1300. * A | | / \ / \ / \ |
  1301. * | | / \ / \ / \ |
  1302. * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  1303. * -- +--------------------------------+
  1304. * |________|_________|_________|
  1305. * T1 T2 T3
  1306. *
  1307. * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  1308. * "R" specifies the radius. "S" specifies the stroke count.
  1309. * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  1310. *
  1311. * Caveats: The ending Z should be the same as starting Z.
  1312. * Attention: EXPERIMENTAL. G-code arguments may change.
  1313. *
  1314. */
  1315. //#define NOZZLE_CLEAN_FEATURE
  1316.  
  1317. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  1318. // Default number of pattern repetitions
  1319. #define NOZZLE_CLEAN_STROKES 12
  1320.  
  1321. // Default number of triangles
  1322. #define NOZZLE_CLEAN_TRIANGLES 3
  1323.  
  1324. // Specify positions as { X, Y, Z }
  1325. #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  1326. #define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)}
  1327.  
  1328. // Circular pattern radius
  1329. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  1330. // Circular pattern circle fragments number
  1331. #define NOZZLE_CLEAN_CIRCLE_FN 10
  1332. // Middle point of circle
  1333. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  1334.  
  1335. // Moves the nozzle to the initial position
  1336. #define NOZZLE_CLEAN_GOBACK
  1337. #endif
  1338.  
  1339. /**
  1340. * Print Job Timer
  1341. *
  1342. * Automatically start and stop the print job timer on M104/M109/M190.
  1343. *
  1344. * M104 (hotend, no wait) - high temp = none, low temp = stop timer
  1345. * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
  1346. * M190 (bed, wait) - high temp = start timer, low temp = none
  1347. *
  1348. * The timer can also be controlled with the following commands:
  1349. *
  1350. * M75 - Start the print job timer
  1351. * M76 - Pause the print job timer
  1352. * M77 - Stop the print job timer
  1353. */
  1354. #define PRINTJOB_TIMER_AUTOSTART
  1355.  
  1356. /**
  1357. * Print Counter
  1358. *
  1359. * Track statistical data such as:
  1360. *
  1361. * - Total print jobs
  1362. * - Total successful print jobs
  1363. * - Total failed print jobs
  1364. * - Total time printing
  1365. *
  1366. * View the current statistics with M78.
  1367. */
  1368. //#define PRINTCOUNTER
  1369.  
  1370. //=============================================================================
  1371. //============================= LCD and SD support ============================
  1372. //=============================================================================
  1373.  
  1374. // @section lcd
  1375.  
  1376. /**
  1377. * LCD LANGUAGE
  1378. *
  1379. * Select the language to display on the LCD. These languages are available:
  1380. *
  1381. * en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
  1382. * eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
  1383. * pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  1384. *
  1385. * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  1386. */
  1387. #define LCD_LANGUAGE en
  1388.  
  1389. /**
  1390. * LCD Character Set
  1391. *
  1392. * Note: This option is NOT applicable to Graphical Displays.
  1393. *
  1394. * All character-based LCDs provide ASCII plus one of these
  1395. * language extensions:
  1396. *
  1397. * - JAPANESE ... the most common
  1398. * - WESTERN ... with more accented characters
  1399. * - CYRILLIC ... for the Russian language
  1400. *
  1401. * To determine the language extension installed on your controller:
  1402. *
  1403. * - Compile and upload with LCD_LANGUAGE set to 'test'
  1404. * - Click the controller to view the LCD menu
  1405. * - The LCD will display Japanese, Western, or Cyrillic text
  1406. *
  1407. * See http://marlinfw.org/docs/development/lcd_language.html
  1408. *
  1409. * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  1410. */
  1411. #define DISPLAY_CHARSET_HD44780 JAPANESE
  1412.  
  1413. /**
  1414. * SD CARD
  1415. *
  1416. * SD Card support is disabled by default. If your controller has an SD slot,
  1417. * you must uncomment the following option or it won't work.
  1418. *
  1419. */
  1420. #define SDSUPPORT
  1421.  
  1422. /**
  1423. * SD CARD: SPI SPEED
  1424. *
  1425. * Enable one of the following items for a slower SPI transfer speed.
  1426. * This may be required to resolve "volume init" errors.
  1427. */
  1428. //#define SPI_SPEED SPI_HALF_SPEED
  1429. //#define SPI_SPEED SPI_QUARTER_SPEED
  1430. //#define SPI_SPEED SPI_EIGHTH_SPEED
  1431.  
  1432. /**
  1433. * SD CARD: ENABLE CRC
  1434. *
  1435. * Use CRC checks and retries on the SD communication.
  1436. */
  1437. //#define SD_CHECK_AND_RETRY
  1438.  
  1439. /**
  1440. * LCD Menu Items
  1441. *
  1442. * Disable all menus and only display the Status Screen, or
  1443. * just remove some extraneous menu items to recover space.
  1444. */
  1445. //#define NO_LCD_MENUS
  1446. //#define SLIM_LCD_MENUS
  1447.  
  1448. //
  1449. // ENCODER SETTINGS
  1450. //
  1451. // This option overrides the default number of encoder pulses needed to
  1452. // produce one step. Should be increased for high-resolution encoders.
  1453. //
  1454. //#define ENCODER_PULSES_PER_STEP 4
  1455.  
  1456. //
  1457. // Use this option to override the number of step signals required to
  1458. // move between next/prev menu items.
  1459. //
  1460. //#define ENCODER_STEPS_PER_MENU_ITEM 1
  1461.  
  1462. /**
  1463. * Encoder Direction Options
  1464. *
  1465. * Test your encoder's behavior first with both options disabled.
  1466. *
  1467. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1468. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1469. * Reversed Value Editing only? Enable BOTH options.
  1470. */
  1471.  
  1472. //
  1473. // This option reverses the encoder direction everywhere.
  1474. //
  1475. // Set this option if CLOCKWISE causes values to DECREASE
  1476. //
  1477. //#define REVERSE_ENCODER_DIRECTION
  1478.  
  1479. //
  1480. // This option reverses the encoder direction for navigating LCD menus.
  1481. //
  1482. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1483. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1484. //
  1485. //#define REVERSE_MENU_DIRECTION
  1486.  
  1487. //
  1488. // Individual Axis Homing
  1489. //
  1490. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1491. //
  1492. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1493.  
  1494. //
  1495. // SPEAKER/BUZZER
  1496. //
  1497. // If you have a speaker that can produce tones, enable it here.
  1498. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1499. //
  1500. //#define SPEAKER
  1501.  
  1502. //
  1503. // The duration and frequency for the UI feedback sound.
  1504. // Set these to 0 to disable audio feedback in the LCD menus.
  1505. //
  1506. // Note: Test audio output with the G-Code:
  1507. // M300 S<frequency Hz> P<duration ms>
  1508. //
  1509. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
  1510. //#define LCD_FEEDBACK_FREQUENCY_HZ 5000
  1511.  
  1512. //=============================================================================
  1513. //======================== LCD / Controller Selection =========================
  1514. //======================== (Character-based LCDs) =========================
  1515. //=============================================================================
  1516.  
  1517. //
  1518. // RepRapDiscount Smart Controller.
  1519. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1520. //
  1521. // Note: Usually sold with a white PCB.
  1522. //
  1523. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1524.  
  1525. //
  1526. // ULTIMAKER Controller.
  1527. //
  1528. //#define ULTIMAKERCONTROLLER
  1529.  
  1530. //
  1531. // ULTIPANEL as seen on Thingiverse.
  1532. //
  1533. //#define ULTIPANEL
  1534.  
  1535. //
  1536. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1537. // http://reprap.org/wiki/PanelOne
  1538. //
  1539. //#define PANEL_ONE
  1540.  
  1541. //
  1542. // GADGETS3D G3D LCD/SD Controller
  1543. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1544. //
  1545. // Note: Usually sold with a blue PCB.
  1546. //
  1547. //#define G3D_PANEL
  1548.  
  1549. //
  1550. // RigidBot Panel V1.0
  1551. // http://www.inventapart.com/
  1552. //
  1553. //#define RIGIDBOT_PANEL
  1554.  
  1555. //
  1556. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  1557. // https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html
  1558. //
  1559. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  1560.  
  1561. //
  1562. // ANET and Tronxy 20x4 Controller
  1563. //
  1564. //#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
  1565. // This LCD is known to be susceptible to electrical interference
  1566. // which scrambles the display. Pressing any button clears it up.
  1567. // This is a LCD2004 display with 5 analog buttons.
  1568.  
  1569. //
  1570. // Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  1571. //
  1572. //#define ULTRA_LCD
  1573.  
  1574. //=============================================================================
  1575. //======================== LCD / Controller Selection =========================
  1576. //===================== (I2C and Shift-Register LCDs) =====================
  1577. //=============================================================================
  1578.  
  1579. //
  1580. // CONTROLLER TYPE: I2C
  1581. //
  1582. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1583. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1584. //
  1585.  
  1586. //
  1587. // Elefu RA Board Control Panel
  1588. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1589. //
  1590. //#define RA_CONTROL_PANEL
  1591.  
  1592. //
  1593. // Sainsmart (YwRobot) LCD Displays
  1594. //
  1595. // These require F.Malpartida's LiquidCrystal_I2C library
  1596. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  1597. //
  1598. //#define LCD_SAINSMART_I2C_1602
  1599. //#define LCD_SAINSMART_I2C_2004
  1600.  
  1601. //
  1602. // Generic LCM1602 LCD adapter
  1603. //
  1604. //#define LCM1602
  1605.  
  1606. //
  1607. // PANELOLU2 LCD with status LEDs,
  1608. // separate encoder and click inputs.
  1609. //
  1610. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1611. // For more info: https://github.com/lincomatic/LiquidTWI2
  1612. //
  1613. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1614. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1615. //
  1616. //#define LCD_I2C_PANELOLU2
  1617.  
  1618. //
  1619. // Panucatt VIKI LCD with status LEDs,
  1620. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1621. //
  1622. //#define LCD_I2C_VIKI
  1623.  
  1624. //
  1625. // CONTROLLER TYPE: Shift register panels
  1626. //
  1627.  
  1628. //
  1629. // 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1630. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  1631. //
  1632. //#define SAV_3DLCD
  1633.  
  1634. //=============================================================================
  1635. //======================= LCD / Controller Selection =======================
  1636. //========================= (Graphical LCDs) ========================
  1637. //=============================================================================
  1638.  
  1639. //
  1640. // CONTROLLER TYPE: Graphical 128x64 (DOGM)
  1641. //
  1642. // IMPORTANT: The U8glib library is required for Graphical Display!
  1643. // https://github.com/olikraus/U8glib_Arduino
  1644. //
  1645.  
  1646. //
  1647. // RepRapDiscount FULL GRAPHIC Smart Controller
  1648. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1649. //
  1650. #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1651.  
  1652. //
  1653. // ReprapWorld Graphical LCD
  1654. // https://reprapworld.com/?products_details&products_id/1218
  1655. //
  1656. //#define REPRAPWORLD_GRAPHICAL_LCD
  1657.  
  1658. //
  1659. // Activate one of these if you have a Panucatt Devices
  1660. // Viki 2.0 or mini Viki with Graphic LCD
  1661. // http://panucatt.com
  1662. //
  1663. //#define VIKI2
  1664. //#define miniVIKI
  1665.  
  1666. //
  1667. // MakerLab Mini Panel with graphic
  1668. // controller and SD support - http://reprap.org/wiki/Mini_panel
  1669. //
  1670. //#define MINIPANEL
  1671.  
  1672. //
  1673. // MaKr3d Makr-Panel with graphic controller and SD support.
  1674. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  1675. //
  1676. //#define MAKRPANEL
  1677.  
  1678. //
  1679. // Adafruit ST7565 Full Graphic Controller.
  1680. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1681. //
  1682. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1683.  
  1684. //
  1685. // BQ LCD Smart Controller shipped by
  1686. // default with the BQ Hephestos 2 and Witbox 2.
  1687. //
  1688. //#define BQ_LCD_SMART_CONTROLLER
  1689.  
  1690. //
  1691. // Cartesio UI
  1692. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1693. //
  1694. //#define CARTESIO_UI
  1695.  
  1696. //
  1697. // LCD for Melzi Card with Graphical LCD
  1698. //
  1699. //#define LCD_FOR_MELZI
  1700.  
  1701. //
  1702. // SSD1306 OLED full graphics generic display
  1703. //
  1704. //#define U8GLIB_SSD1306
  1705.  
  1706. //
  1707. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1708. //
  1709. //#define SAV_3DGLCD
  1710. #if ENABLED(SAV_3DGLCD)
  1711. //#define U8GLIB_SSD1306
  1712. #define U8GLIB_SH1106
  1713. #endif
  1714.  
  1715. //
  1716. // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder
  1717. // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1)
  1718. //
  1719. //#define ULTI_CONTROLLER
  1720.  
  1721. //
  1722. // TinyBoy2 128x64 OLED / Encoder Panel
  1723. //
  1724. //#define OLED_PANEL_TINYBOY2
  1725.  
  1726. //
  1727. // MKS MINI12864 with graphic controller and SD support
  1728. // http://reprap.org/wiki/MKS_MINI_12864
  1729. //
  1730. //#define MKS_MINI_12864
  1731.  
  1732. //
  1733. // Factory display for Creality CR-10
  1734. // https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html
  1735. //
  1736. // This is RAMPS-compatible using a single 10-pin connector.
  1737. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  1738. //
  1739. //#define CR10_STOCKDISPLAY
  1740.  
  1741. //
  1742. // ANET and Tronxy Graphical Controller
  1743. //
  1744. //#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  1745. // A clone of the RepRapDiscount full graphics display but with
  1746. // different pins/wiring (see pins_ANET_10.h).
  1747.  
  1748. //
  1749. // MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER
  1750. // http://reprap.org/wiki/MKS_12864OLED
  1751. //
  1752. // Tiny, but very sharp OLED display
  1753. //
  1754. //#define MKS_12864OLED // Uses the SH1106 controller (default)
  1755. //#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller
  1756.  
  1757. //
  1758. // Silvergate GLCD controller
  1759. // http://github.com/android444/Silvergate
  1760. //
  1761. //#define SILVER_GATE_GLCD_CONTROLLER
  1762.  
  1763. //=============================================================================
  1764. //============================ Other Controllers ============================
  1765. //=============================================================================
  1766.  
  1767. //
  1768. // CONTROLLER TYPE: Standalone / Serial
  1769. //
  1770.  
  1771. //
  1772. // LCD for Malyan M200 printers.
  1773. // This requires SDSUPPORT to be enabled
  1774. //
  1775. //#define MALYAN_LCD
  1776.  
  1777. //
  1778. // CONTROLLER TYPE: Keypad / Add-on
  1779. //
  1780.  
  1781. //
  1782. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  1783. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  1784. //
  1785. // REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
  1786. // is pressed, a value of 10.0 means 10mm per click.
  1787. //
  1788. //#define REPRAPWORLD_KEYPAD
  1789. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0
  1790.  
  1791. //=============================================================================
  1792. //=============================== Extra Features ==============================
  1793. //=============================================================================
  1794.  
  1795. // @section extras
  1796.  
  1797. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  1798. //#define FAST_PWM_FAN
  1799.  
  1800. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  1801. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  1802. // is too low, you should also increment SOFT_PWM_SCALE.
  1803. //#define FAN_SOFT_PWM
  1804.  
  1805. // Incrementing this by 1 will double the software PWM frequency,
  1806. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  1807. // However, control resolution will be halved for each increment;
  1808. // at zero value, there are 128 effective control positions.
  1809. #define SOFT_PWM_SCALE 0
  1810.  
  1811. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  1812. // be used to mitigate the associated resolution loss. If enabled,
  1813. // some of the PWM cycles are stretched so on average the desired
  1814. // duty cycle is attained.
  1815. //#define SOFT_PWM_DITHER
  1816.  
  1817. // Temperature status LEDs that display the hotend and bed temperature.
  1818. // If all hotends, bed temperature, and target temperature are under 54C
  1819. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  1820. //#define TEMP_STAT_LEDS
  1821.  
  1822. // M240 Triggers a camera by emulating a Canon RC-1 Remote
  1823. // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
  1824. //#define PHOTOGRAPH_PIN 23
  1825.  
  1826. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  1827. //#define SF_ARC_FIX
  1828.  
  1829. // Support for the BariCUDA Paste Extruder
  1830. //#define BARICUDA
  1831.  
  1832. // Support for BlinkM/CyzRgb
  1833. //#define BLINKM
  1834.  
  1835. // Support for PCA9632 PWM LED driver
  1836. //#define PCA9632
  1837.  
  1838. /**
  1839. * RGB LED / LED Strip Control
  1840. *
  1841. * Enable support for an RGB LED connected to 5V digital pins, or
  1842. * an RGB Strip connected to MOSFETs controlled by digital pins.
  1843. *
  1844. * Adds the M150 command to set the LED (or LED strip) color.
  1845. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  1846. * luminance values can be set from 0 to 255.
  1847. * For Neopixel LED an overall brightness parameter is also available.
  1848. *
  1849. * *** CAUTION ***
  1850. * LED Strips require a MOSFET Chip between PWM lines and LEDs,
  1851. * as the Arduino cannot handle the current the LEDs will require.
  1852. * Failure to follow this precaution can destroy your Arduino!
  1853. * NOTE: A separate 5V power supply is required! The Neopixel LED needs
  1854. * more current than the Arduino 5V linear regulator can produce.
  1855. * *** CAUTION ***
  1856. *
  1857. * LED Type. Enable only one of the following two options.
  1858. *
  1859. */
  1860. //#define RGB_LED
  1861. //#define RGBW_LED
  1862.  
  1863. #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
  1864. #define RGB_LED_R_PIN 34
  1865. #define RGB_LED_G_PIN 43
  1866. #define RGB_LED_B_PIN 35
  1867. #define RGB_LED_W_PIN -1
  1868. #endif
  1869.  
  1870. // Support for Adafruit Neopixel LED driver
  1871. //#define NEOPIXEL_LED
  1872. #if ENABLED(NEOPIXEL_LED)
  1873. #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  1874. #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
  1875. #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
  1876. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  1877. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
  1878. //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
  1879. #endif
  1880.  
  1881. /**
  1882. * Printer Event LEDs
  1883. *
  1884. * During printing, the LEDs will reflect the printer status:
  1885. *
  1886. * - Gradually change from blue to violet as the heated bed gets to target temp
  1887. * - Gradually change from violet to red as the hotend gets to temperature
  1888. * - Change to white to illuminate work surface
  1889. * - Change to green once print has finished
  1890. * - Turn off after the print has finished and the user has pushed a button
  1891. */
  1892. #if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
  1893. #define PRINTER_EVENT_LEDS
  1894. #endif
  1895.  
  1896. /**
  1897. * R/C SERVO support
  1898. * Sponsored by TrinityLabs, Reworked by codexmas
  1899. */
  1900.  
  1901. /**
  1902. * Number of servos
  1903. *
  1904. * For some servo-related options NUM_SERVOS will be set automatically.
  1905. * Set this manually if there are extra servos needing manual control.
  1906. * Leave undefined or set to 0 to entirely disable the servo subsystem.
  1907. */
  1908. #define NUM_SERVOS 1 // Servo index starts with 0 for M280 command
  1909.  
  1910. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
  1911. // 300ms is a good value but you can try less delay.
  1912. // If the servo can't reach the requested position, increase it.
  1913. #define SERVO_DELAY { 300 }
  1914.  
  1915. // Servo deactivation
  1916. //
  1917. // With this option servos are powered only during movement, then turned off to prevent jitter.
  1918. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  1919.  
  1920. #endif // CONFIGURATION_H
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!