API tools faq
paste
Advertisement
Guest User

CR-10S BLTouch Configuration.h

a guest
Jan 18th, 2018
320
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 66.09 KB | None | 0 0
raw download clone embed print report
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22.  
  23. /**
  24. * Configuration.h
  25. *
  26. * Basic settings such as:
  27. *
  28. * - Type of electronics
  29. * - Type of temperature sensor
  30. * - Printer geometry
  31. * - Endstop configuration
  32. * - LCD controller
  33. * - Extra features
  34. *
  35. * Advanced settings can be found in Configuration_adv.h
  36. *
  37. */
  38. #ifndef CONFIGURATION_H
  39. #define CONFIGURATION_H
  40. #define CONFIGURATION_H_VERSION 010107
  41.  
  42. //===========================================================================
  43. //============================= Getting Started =============================
  44. //===========================================================================
  45.  
  46. /**
  47. * Here are some standard links for getting your machine calibrated:
  48. *
  49. * http://reprap.org/wiki/Calibration
  50. * http://youtu.be/wAL9d7FgInk
  51. * http://calculator.josefprusa.cz
  52. * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  53. * http://www.thingiverse.com/thing:5573
  54. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  55. * http://www.thingiverse.com/thing:298812
  56. */
  57.  
  58. //===========================================================================
  59. //============================= DELTA Printer ===============================
  60. //===========================================================================
  61. // For a Delta printer start with one of the configuration files in the
  62. // example_configurations/delta directory and customize for your machine.
  63. //
  64.  
  65. //===========================================================================
  66. //============================= SCARA Printer ===============================
  67. //===========================================================================
  68. // For a SCARA printer start with the configuration files in
  69. // example_configurations/SCARA and customize for your machine.
  70. //
  71.  
  72. // @section info
  73.  
  74. // User-specified version info of this build to display in [Pronterface, etc] terminal window during
  75. // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
  76. // build by the user have been successfully uploaded into firmware.
  77. #define STRING_CONFIG_H_AUTHOR "Anthony Hart" // Who made the changes.
  78. //#define SHOW_BOOTSCREEN
  79. #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
  80. #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
  81.  
  82. //
  83. // *** VENDORS PLEASE READ *****************************************************
  84. //
  85. // Marlin now allow you to have a vendor boot image to be displayed on machine
  86. // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
  87. // custom boot image and then the default Marlin boot image is shown.
  88. //
  89. // We suggest for you to take advantage of this new feature and keep the Marlin
  90. // boot image unmodified. For an example have a look at the bq Hephestos 2
  91. // example configuration folder.
  92. //
  93. //#define SHOW_CUSTOM_BOOTSCREEN
  94. // @section machine
  95.  
  96. /**
  97. * Select which serial port on the board will be used for communication with the host.
  98. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  99. * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
  100. *
  101. * :[0, 1, 2, 3, 4, 5, 6, 7]
  102. */
  103. #define SERIAL_PORT 0
  104.  
  105. /**
  106. * This setting determines the communication speed of the printer.
  107. *
  108. * 250000 works in most cases, but you might try a lower speed if
  109. * you commonly experience drop-outs during host printing.
  110. * You may try up to 1000000 to speed up SD file transfer.
  111. *
  112. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  113. */
  114. #define BAUDRATE 115200
  115.  
  116. // Enable the Bluetooth serial interface on AT90USB devices
  117. //#define BLUETOOTH
  118.  
  119. // The following define selects which electronics board you have.
  120. // Please choose the name from boards.h that matches your setup
  121. #ifndef MOTHERBOARD
  122. #define MOTHERBOARD BOARD_RAMPS_14_EFB
  123. #endif
  124.  
  125. // Optional custom name for your RepStrap or other custom machine
  126. // Displayed in the LCD "Ready" message
  127. #define CUSTOM_MACHINE_NAME "Always"
  128.  
  129. // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
  130. // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
  131. #define MACHINE_UUID "ABCDEFGH-1234-5678-9012-ABC123DEF456"
  132.  
  133. // @section extruder
  134.  
  135. // This defines the number of extruders
  136. // :[1, 2, 3, 4, 5]
  137. #define EXTRUDERS 1
  138.  
  139. // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
  140. #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
  141.  
  142. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  143. //#define SINGLENOZZLE
  144.  
  145. /**
  146. * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.
  147. *
  148. * This device allows one stepper driver on a control board to drive
  149. * two to eight stepper motors, one at a time, in a manner suitable
  150. * for extruders.
  151. *
  152. * This option only allows the multiplexer to switch on tool-change.
  153. * Additional options to configure custom E moves are pending.
  154. */
  155. //#define MK2_MULTIPLEXER
  156. #if ENABLED(MK2_MULTIPLEXER)
  157. // Override the default DIO selector pins here, if needed.
  158. // Some pins files may provide defaults for these pins.
  159. //#define E_MUX0_PIN 40 // Always Required
  160. //#define E_MUX1_PIN 42 // Needed for 3 to 8 steppers
  161. //#define E_MUX2_PIN 44 // Needed for 5 to 8 steppers
  162. #endif
  163.  
  164. // A dual extruder that uses a single stepper motor
  165. //#define SWITCHING_EXTRUDER
  166. #if ENABLED(SWITCHING_EXTRUDER)
  167. #define SWITCHING_EXTRUDER_SERVO_NR 0
  168. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  169. #if EXTRUDERS > 3
  170. #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  171. #endif
  172. #endif
  173.  
  174. // A dual-nozzle that uses a servomotor to raise/lower one of the nozzles
  175. //#define SWITCHING_NOZZLE
  176. #if ENABLED(SWITCHING_NOZZLE)
  177. #define SWITCHING_NOZZLE_SERVO_NR 0
  178. #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
  179. //#define HOTEND_OFFSET_Z { 0.0, 0.0 }
  180. #endif
  181.  
  182. /**
  183. * Two separate X-carriages with extruders that connect to a moving part
  184. * via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  185. */
  186. //#define PARKING_EXTRUDER
  187. #if ENABLED(PARKING_EXTRUDER)
  188. #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
  189. #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
  190. #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
  191. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
  192. #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
  193. #define PARKING_EXTRUDER_SECURITY_RAISE 5 // Z-raise before parking
  194. #define HOTEND_OFFSET_Z { 0.0, 1.3 } // Z-offsets of the two hotends. The first must be 0.
  195. #endif
  196.  
  197. /**
  198. * "Mixing Extruder"
  199. * - Adds a new code, M165, to set the current mix factors.
  200. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  201. * - Optional support for Repetier Firmware M163, M164, and virtual extruder.
  202. * - This implementation supports only a single extruder.
  203. * - Enable DIRECT_MIXING_IN_G1 for Pia Taubert's reference implementation
  204. */
  205. //#define MIXING_EXTRUDER
  206. #if ENABLED(MIXING_EXTRUDER)
  207. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  208. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  209. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  210. #endif
  211.  
  212. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  213. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  214. // For the other hotends it is their distance from the extruder 0 hotend.
  215. //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
  216. //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
  217.  
  218. // @section machine
  219.  
  220. /**
  221. * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
  222. *
  223. * 0 = No Power Switch
  224. * 1 = ATX
  225. * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
  226. *
  227. * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
  228. */
  229. #define POWER_SUPPLY 0
  230.  
  231. #if POWER_SUPPLY > 0
  232. // Enable this option to leave the PSU off at startup.
  233. // Power to steppers and heaters will need to be turned on with M80.
  234. //#define PS_DEFAULT_OFF
  235. #endif
  236.  
  237. // @section temperature
  238.  
  239. //===========================================================================
  240. //============================= Thermal Settings ============================
  241. //===========================================================================
  242.  
  243. /**
  244. * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  245. *
  246. * Temperature sensors available:
  247. *
  248. * -3 : thermocouple with MAX31855 (only for sensor 0)
  249. * -2 : thermocouple with MAX6675 (only for sensor 0)
  250. * -1 : thermocouple with AD595
  251. * 0 : not used
  252. * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  253. * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  254. * 3 : Mendel-parts thermistor (4.7k pullup)
  255. * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  256. * 5 : 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
  257. * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  258. * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  259. * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  260. * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  261. * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  262. * 10 : 100k RS thermistor 198-961 (4.7k pullup)
  263. * 11 : 100k beta 3950 1% thermistor (4.7k pullup)
  264. * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  265. * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  266. * 20 : the PT100 circuit found in the Ultimainboard V2.x
  267. * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  268. * 66 : 4.7M High Temperature thermistor from Dyze Design
  269. * 70 : the 100K thermistor found in the bq Hephestos 2
  270. * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
  271. *
  272. * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  273. * (but gives greater accuracy and more stable PID)
  274. * 51 : 100k thermistor - EPCOS (1k pullup)
  275. * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  276. * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  277. *
  278. * 1047 : Pt1000 with 4k7 pullup
  279. * 1010 : Pt1000 with 1k pullup (non standard)
  280. * 147 : Pt100 with 4k7 pullup
  281. * 110 : Pt100 with 1k pullup (non standard)
  282. *
  283. * Use these for Testing or Development purposes. NEVER for production machine.
  284. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  285. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  286. *
  287. * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
  288. */
  289. #define TEMP_SENSOR_0 5
  290. #define TEMP_SENSOR_1 0
  291. #define TEMP_SENSOR_2 0
  292. #define TEMP_SENSOR_3 0
  293. #define TEMP_SENSOR_4 0
  294. #define TEMP_SENSOR_BED 5
  295.  
  296. // Dummy thermistor constant temperature readings, for use with 998 and 999
  297. #define DUMMY_THERMISTOR_998_VALUE 25
  298. #define DUMMY_THERMISTOR_999_VALUE 100
  299.  
  300. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  301. // from the two sensors differ too much the print will be aborted.
  302. //#define TEMP_SENSOR_1_AS_REDUNDANT
  303. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  304.  
  305. // Extruder temperature must be close to target for this long before M109 returns success
  306. #define TEMP_RESIDENCY_TIME 10 // (seconds)
  307. #define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  308. #define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  309.  
  310. // Bed temperature must be close to target for this long before M190 returns success
  311. #define TEMP_BED_RESIDENCY_TIME 10 // (seconds)
  312. #define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  313. #define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  314.  
  315. // The minimal temperature defines the temperature below which the heater will not be enabled It is used
  316. // to check that the wiring to the thermistor is not broken.
  317. // Otherwise this would lead to the heater being powered on all the time.
  318. #define HEATER_0_MINTEMP 5
  319. #define HEATER_1_MINTEMP 5
  320. #define HEATER_2_MINTEMP 5
  321. #define HEATER_3_MINTEMP 5
  322. #define HEATER_4_MINTEMP 5
  323. #define BED_MINTEMP 5
  324.  
  325. // When temperature exceeds max temp, your heater will be switched off.
  326. // This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
  327. // You should use MINTEMP for thermistor short/failure protection.
  328. #define HEATER_0_MAXTEMP 300
  329. #define HEATER_1_MAXTEMP 300
  330. #define HEATER_2_MAXTEMP 300
  331. #define HEATER_3_MAXTEMP 300
  332. #define HEATER_4_MAXTEMP 300
  333. #define BED_MAXTEMP 150
  334.  
  335. //===========================================================================
  336. //============================= PID Settings ================================
  337. //===========================================================================
  338. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  339.  
  340. // Comment the following line to disable PID and enable bang-bang.
  341. #define PIDTEMP
  342. #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current
  343. #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  344. #define PID_K1 0.95 // Smoothing factor within the PID
  345. #if ENABLED(PIDTEMP)
  346. #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
  347. //#define PID_DEBUG // Sends debug data to the serial port.
  348. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  349. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  350. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  351. // Set/get with gcode: M301 E[extruder number, 0-2]
  352. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  353. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  354.  
  355. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  356.  
  357. // E3D Volcano w/ 40w 12v heater cartridge (red shielding)
  358. #define DEFAULT_Kp 13.88
  359. #define DEFAULT_Ki 0.91
  360. #define DEFAULT_Kd 53.14
  361.  
  362. #endif // PIDTEMP
  363.  
  364. //===========================================================================
  365. //============================= PID > Bed Temperature Control ===============
  366. //===========================================================================
  367. // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
  368. //
  369. // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
  370. // If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
  371. // which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
  372. // This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
  373. // If your configuration is significantly different than this and you don't understand the issues involved, you probably
  374. // shouldn't use bed PID until someone else verifies your hardware works.
  375. // If this is enabled, find your own PID constants below.
  376. #define PIDTEMPBED
  377.  
  378. //#define BED_LIMIT_SWITCHING
  379.  
  380. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
  381. // all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
  382. // setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
  383. // so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
  384. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  385.  
  386. #if ENABLED(PIDTEMPBED)
  387.  
  388. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  389.  
  390. // CR-10S 300m bed with glass
  391. #define DEFAULT_bedKp 479.95
  392. #define DEFAULT_bedKi 83.70
  393. #define DEFAULT_bedKd 688.07
  394.  
  395. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  396. #endif // PIDTEMPBED
  397.  
  398. // @section extruder
  399.  
  400. // This option prevents extrusion if the temperature is below EXTRUDE_MINTEMP.
  401. // It also enables the M302 command to set the minimum extrusion temperature
  402. // or to allow moving the extruder regardless of the hotend temperature.
  403. // *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  404. #define PREVENT_COLD_EXTRUSION
  405. #define EXTRUDE_MINTEMP 170
  406.  
  407. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
  408. // Note that for Bowden Extruders a too-small value here may prevent loading.
  409. #define PREVENT_LENGTHY_EXTRUDE
  410. #define EXTRUDE_MAXLENGTH 1000
  411.  
  412. //===========================================================================
  413. //======================== Thermal Runaway Protection =======================
  414. //===========================================================================
  415.  
  416. /**
  417. * Thermal Protection provides additional protection to your printer from damage
  418. * and fire. Marlin always includes safe min and max temperature ranges which
  419. * protect against a broken or disconnected thermistor wire.
  420. *
  421. * The issue: If a thermistor falls out, it will report the much lower
  422. * temperature of the air in the room, and the the firmware will keep
  423. * the heater on.
  424. *
  425. * If you get "Thermal Runaway" or "Heating failed" errors the
  426. * details can be tuned in Configuration_adv.h
  427. */
  428.  
  429. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  430. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  431.  
  432. //===========================================================================
  433. //============================= Mechanical Settings =========================
  434. //===========================================================================
  435.  
  436. // @section machine
  437.  
  438. // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
  439. // either in the usual order or reversed
  440. //#define COREXY
  441. //#define COREXZ
  442. //#define COREYZ
  443. //#define COREYX
  444. //#define COREZX
  445. //#define COREZY
  446.  
  447. //===========================================================================
  448. //============================== Endstop Settings ===========================
  449. //===========================================================================
  450.  
  451. // @section homing
  452.  
  453. // Specify here all the endstop connectors that are connected to any endstop or probe.
  454. // Almost all printers will be using one per axis. Probes will use one or more of the
  455. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  456. #define USE_XMIN_PLUG
  457. #define USE_YMIN_PLUG
  458. #define USE_ZMIN_PLUG
  459. //#define USE_XMAX_PLUG
  460. //#define USE_YMAX_PLUG
  461. //#define USE_ZMAX_PLUG
  462.  
  463. // coarse Endstop Settings
  464. #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
  465.  
  466. #if DISABLED(ENDSTOPPULLUPS)
  467. // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
  468. //#define ENDSTOPPULLUP_XMAX
  469. //#define ENDSTOPPULLUP_YMAX
  470. //#define ENDSTOPPULLUP_ZMAX
  471. //#define ENDSTOPPULLUP_XMIN
  472. //#define ENDSTOPPULLUP_YMIN
  473. //#define ENDSTOPPULLUP_ZMIN
  474. //#define ENDSTOPPULLUP_ZMIN_PROBE
  475. #endif
  476.  
  477. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  478. #define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  479. #define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  480. #define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  481. #define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  482. #define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  483. #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  484. #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
  485.  
  486. // Enable this feature if all enabled endstop pins are interrupt-capable.
  487. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  488. //#define ENDSTOP_INTERRUPTS_FEATURE
  489.  
  490. //=============================================================================
  491. //============================== Movement Settings ============================
  492. //=============================================================================
  493. // @section motion
  494.  
  495. /**
  496. * Default Settings
  497. *
  498. * These settings can be reset by M502
  499. *
  500. * Note that if EEPROM is enabled, saved values will override these.
  501. */
  502.  
  503. /**
  504. * With this option each E stepper can have its own factors for the
  505. * following movement settings. If fewer factors are given than the
  506. * total number of extruders, the last value applies to the rest.
  507. */
  508. //#define DISTINCT_E_FACTORS
  509.  
  510. /**
  511. * Default Axis Steps Per Unit (steps/mm)
  512. * Override with M92
  513. * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  514. */
  515. #define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 99 }
  516.  
  517. /**
  518. * Default Max Feed Rate (mm/s)
  519. * Override with M203
  520. * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  521. */
  522. #define DEFAULT_MAX_FEEDRATE { 300, 300, 15, 25 }
  523.  
  524. /**
  525. * Default Max Acceleration (change/s) change = mm/s
  526. * (Maximum start speed for accelerated moves)
  527. * Override with M201
  528. * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  529. */
  530. #define DEFAULT_MAX_ACCELERATION { 1000, 1000, 100, 500 }
  531.  
  532. /**
  533. * Default Acceleration (change/s) change = mm/s
  534. * Override with M204
  535. *
  536. * M204 P Acceleration
  537. * M204 R Retract Acceleration
  538. * M204 T Travel Acceleration
  539. */
  540. #define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves
  541. #define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts
  542. #define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves
  543.  
  544. /**
  545. * Default Jerk (mm/s)
  546. * Override with M205 X Y Z E
  547. *
  548. * "Jerk" specifies the minimum speed change that requires acceleration.
  549. * When changing speed and direction, if the difference is less than the
  550. * value set here, it may happen instantaneously.
  551. */
  552. #define DEFAULT_XJERK 15.0
  553. #define DEFAULT_YJERK 15.0
  554. #define DEFAULT_ZJERK 0.4
  555. #define DEFAULT_EJERK 5.0
  556.  
  557. //===========================================================================
  558. //============================= Z Probe Options =============================
  559. //===========================================================================
  560. // @section probes
  561.  
  562. //
  563. // See http://marlinfw.org/docs/configuration/probes.html
  564. //
  565.  
  566. /**
  567. * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  568. *
  569. * Enable this option for a probe connected to the Z Min endstop pin.
  570. */
  571. //#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  572.  
  573. /**
  574. * Z_MIN_PROBE_ENDSTOP
  575. *
  576. * Enable this option for a probe connected to any pin except Z-Min.
  577. * (By default Marlin assumes the Z-Max endstop pin.)
  578. * To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
  579. *
  580. * - The simplest option is to use a free endstop connector.
  581. * - Use 5V for powered (usually inductive) sensors.
  582. *
  583. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  584. * - For simple switches connect...
  585. * - normally-closed switches to GND and D32.
  586. * - normally-open switches to 5V and D32.
  587. *
  588. * WARNING: Setting the wrong pin may have unexpected and potentially
  589. * disastrous consequences. Use with caution and do your homework.
  590. *
  591. */
  592. #define Z_MIN_PROBE_ENDSTOP
  593. #define Z_MIN_PROBE_PIN 19
  594.  
  595. /**
  596. * Probe Type
  597. *
  598. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  599. * Activate one of these to use Auto Bed Leveling below.
  600. */
  601.  
  602. /**
  603. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  604. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  605. * or (with LCD_BED_LEVELING) the LCD controller.
  606. */
  607. //#define PROBE_MANUALLY
  608.  
  609. /**
  610. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  611. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  612. */
  613. //#define FIX_MOUNTED_PROBE
  614.  
  615. /**
  616. * Z Servo Probe, such as an endstop switch on a rotating arm.
  617. */
  618. //#define Z_ENDSTOP_SERVO_NR 0 // Defaults to SERVO 0 connector.
  619. //#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles
  620.  
  621. /**
  622. * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  623. */
  624. #define BLTOUCH
  625. #if ENABLED(BLTOUCH)
  626. #define BLTOUCH_DELAY 100 // (ms) Enable and increase if needed
  627. #endif
  628.  
  629. /**
  630. * Enable one or more of the following if probing seems unreliable.
  631. * Heaters and/or fans can be disabled during probing to minimize electrical
  632. * noise. A delay can also be added to allow noise and vibration to settle.
  633. * These options are most useful for the BLTouch probe, but may also improve
  634. * readings with inductive probes and piezo sensors.
  635. */
  636. #define PROBING_HEATERS_OFF // Turn heaters off when probing
  637. #define PROBING_FANS_OFF // Turn fans off when probing
  638. #define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
  639.  
  640. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  641. //#define SOLENOID_PROBE
  642.  
  643. // A sled-mounted probe like those designed by Charles Bell.
  644. //#define Z_PROBE_SLED
  645. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  646.  
  647. //
  648. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  649. //
  650.  
  651. /**
  652. * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  653. * X and Y offsets must be integers.
  654. *
  655. * In the following example the X and Y offsets are both positive:
  656. * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
  657. * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
  658. *
  659. * +-- BACK ---+
  660. * | |
  661. * L | (+) P | R <-- probe (20,20)
  662. * E | | I
  663. * F | (-) N (+) | G <-- nozzle (10,10)
  664. * T | | H
  665. * | (-) | T
  666. * | |
  667. * O-- FRONT --+
  668. * (0,0)
  669. */
  670. #define X_PROBE_OFFSET_FROM_EXTRUDER -55 // X offset: -left +right [of the nozzle]
  671. #define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front +behind [the nozzle]
  672. #define Z_PROBE_OFFSET_FROM_EXTRUDER -0.331850
  673. // Z offset: -below +above [the nozzle]
  674.  
  675. // X and Y axis travel speed (mm/m) between probes
  676. #define XY_PROBE_SPEED 10000
  677.  
  678. // Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
  679. #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
  680.  
  681. // Speed for the "accurate" probe of each point
  682. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
  683.  
  684. // The number of probes to perform at each point.
  685. // Set to 2 for a fast/slow probe, using the second probe result.
  686. // Set to 3 or more for slow probes, averaging the results.
  687. #define MULTIPLE_PROBING 2
  688.  
  689. /**
  690. * Z probes require clearance when deploying, stowing, and moving between
  691. * probe points to avoid hitting the bed and other hardware.
  692. * Servo-mounted probes require extra space for the arm to rotate.
  693. * Inductive probes need space to keep from triggering early.
  694. *
  695. * Use these settings to specify the distance (mm) to raise the probe (or
  696. * lower the bed). The values set here apply over and above any (negative)
  697. * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
  698. * Only integer values >= 1 are valid here.
  699. *
  700. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  701. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  702. */
  703. #define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
  704. #define Z_CLEARANCE_BETWEEN_PROBES 10 // Z Clearance between probe points
  705.  
  706. // For M851 give a range for adjusting the Z probe offset
  707. #define Z_PROBE_OFFSET_RANGE_MIN -10
  708. #define Z_PROBE_OFFSET_RANGE_MAX 10
  709.  
  710. // Enable the M48 repeatability test to test probe accuracy
  711. #define Z_MIN_PROBE_REPEATABILITY_TEST
  712.  
  713. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  714. // :{ 0:'Low', 1:'High' }
  715. #define X_ENABLE_ON 0
  716. #define Y_ENABLE_ON 0
  717. #define Z_ENABLE_ON 0
  718. #define E_ENABLE_ON 0 // For all extruders
  719.  
  720. // Disables axis stepper immediately when it's not being used.
  721. // WARNING: When motors turn off there is a chance of losing position accuracy!
  722. #define DISABLE_X false
  723. #define DISABLE_Y false
  724. #define DISABLE_Z false
  725. // Warn on display about possibly reduced accuracy
  726. //#define DISABLE_REDUCED_ACCURACY_WARNING
  727.  
  728. // @section extruder
  729.  
  730. #define DISABLE_E false // For all extruders
  731. #define DISABLE_INACTIVE_EXTRUDER true // Keep only the active extruder enabled.
  732.  
  733. // @section machine
  734.  
  735. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  736. #define INVERT_X_DIR false
  737. #define INVERT_Y_DIR false
  738. #define INVERT_Z_DIR true
  739.  
  740. // Enable this option for Toshiba stepper drivers
  741. //#define CONFIG_STEPPERS_TOSHIBA
  742.  
  743. // @section extruder
  744.  
  745. // For direct drive extruder v9 set to true, for geared extruder set to false.
  746. #define INVERT_E0_DIR false
  747. #define INVERT_E1_DIR false
  748. #define INVERT_E2_DIR false
  749. #define INVERT_E3_DIR false
  750. #define INVERT_E4_DIR false
  751.  
  752. // @section homing
  753.  
  754. //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
  755.  
  756. #define Z_HOMING_HEIGHT 10 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
  757. // Be sure you have this distance over your Z_MAX_POS in case.
  758.  
  759. // Direction of endstops when homing; 1=MAX, -1=MIN
  760. // :[-1,1]
  761. #define X_HOME_DIR -1
  762. #define Y_HOME_DIR -1
  763. #define Z_HOME_DIR -1
  764.  
  765. // @section machine
  766.  
  767. // The size of the print bed
  768. #define X_BED_SIZE 300
  769. #define Y_BED_SIZE 300
  770. #define Z_MAX_HEIGHT 390
  771.  
  772. // Travel limits (mm) after homing, corresponding to endstop positions.
  773. #define X_MIN_POS 0
  774. #define Y_MIN_POS -4
  775. #define Z_MIN_POS 0
  776. #define X_MAX_POS X_BED_SIZE
  777. #define Y_MAX_POS Y_BED_SIZE
  778. #define Z_MAX_POS Z_MAX_HEIGHT-Z_HOMING_HEIGHT
  779.  
  780. /**
  781. * Software Endstops
  782. *
  783. * - Prevent moves outside the set machine bounds.
  784. * - Individual axes can be disabled, if desired.
  785. * - X and Y only apply to Cartesian robots.
  786. * - Use 'M211' to set software endstops on/off or report current state
  787. */
  788.  
  789. // Min software endstops curtail movement below minimum coordinate bounds
  790. #define MIN_SOFTWARE_ENDSTOPS
  791. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  792. #define MIN_SOFTWARE_ENDSTOP_X
  793. #define MIN_SOFTWARE_ENDSTOP_Y
  794. #define MIN_SOFTWARE_ENDSTOP_Z
  795. #endif
  796.  
  797. // Max software endstops curtail movement above maximum coordinate bounds
  798. #define MAX_SOFTWARE_ENDSTOPS
  799. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  800. #define MAX_SOFTWARE_ENDSTOP_X
  801. #define MAX_SOFTWARE_ENDSTOP_Y
  802. #define MAX_SOFTWARE_ENDSTOP_Z
  803. #endif
  804.  
  805. /**
  806. * Filament Runout Sensor
  807. * A mechanical or opto endstop is used to check for the presence of filament.
  808. *
  809. * RAMPS-based boards use SERVO3_PIN.
  810. * For other boards you may need to define FIL_RUNOUT_PIN.
  811. * By default the firmware assumes HIGH = has filament, LOW = ran out
  812. */
  813. #define FILAMENT_RUNOUT_SENSOR
  814. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  815. #define FIL_RUNOUT_INVERTING true // set to true to invert the logic of the sensor.
  816. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
  817. #define FILAMENT_RUNOUT_SCRIPT "M600"
  818. #endif
  819.  
  820. //===========================================================================
  821. //=============================== Bed Leveling ==============================
  822. //===========================================================================
  823. // @section calibrate
  824.  
  825. /**
  826. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  827. * and behavior of G29 will change depending on your selection.
  828. *
  829. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  830. *
  831. * - AUTO_BED_LEVELING_3POINT
  832. * Probe 3 arbitrary points on the bed (that aren't collinear)
  833. * You specify the XY coordinates of all 3 points.
  834. * The result is a single tilted plane. Best for a flat bed.
  835. *
  836. * - AUTO_BED_LEVELING_LINEAR
  837. * Probe several points in a grid.
  838. * You specify the rectangle and the density of sample points.
  839. * The result is a single tilted plane. Best for a flat bed.
  840. *
  841. * - AUTO_BED_LEVELING_BILINEAR
  842. * Probe several points in a grid.
  843. * You specify the rectangle and the density of sample points.
  844. * The result is a mesh, best for large or uneven beds.
  845. *
  846. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  847. * A comprehensive bed leveling system combining the features and benefits
  848. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  849. * Validation and Mesh Editing systems.
  850. *
  851. * - MESH_BED_LEVELING
  852. * Probe a grid manually
  853. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  854. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  855. * leveling in steps so you can manually adjust the Z height at each grid-point.
  856. * With an LCD controller the process is guided step-by-step.
  857. */
  858. //#define AUTO_BED_LEVELING_3POINT
  859. //#define AUTO_BED_LEVELING_LINEAR
  860. //#define AUTO_BED_LEVELING_BILINEAR
  861. #define AUTO_BED_LEVELING_UBL
  862. //#define MESH_BED_LEVELING
  863.  
  864. /**
  865. * Enable detailed logging of G28, G29, M48, etc.
  866. * Turn on with the command 'M111 S32'.
  867. * NOTE: Requires a lot of PROGMEM!
  868. */
  869. //#define DEBUG_LEVELING_FEATURE
  870.  
  871. #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
  872. // Gradually reduce leveling correction until a set height is reached,
  873. // at which point movement will be level to the machine's XY plane.
  874. // The height can be set with M420 Z<height>
  875. #define ENABLE_LEVELING_FADE_HEIGHT
  876.  
  877. // For Cartesian machines, instead of dividing moves on mesh boundaries,
  878. // split up moves into short segments like a Delta. This follows the
  879. // contours of the bed more closely than edge-to-edge straight moves.
  880. #define SEGMENT_LEVELED_MOVES
  881. #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
  882.  
  883. /**
  884. * Enable the G26 Mesh Validation Pattern tool.
  885. */
  886. #define G26_MESH_VALIDATION // Enable G26 mesh validation
  887. #if ENABLED(G26_MESH_VALIDATION)
  888. #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
  889. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
  890. #define MESH_TEST_HOTEND_TEMP 205.0 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
  891. #define MESH_TEST_BED_TEMP 70.0 // (°C) Default bed temperature for the G26 Mesh Validation Tool.
  892. #endif
  893.  
  894. #endif
  895.  
  896. #if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)
  897.  
  898. // Set the number of grid points per dimension.
  899. #define GRID_MAX_POINTS_X 5
  900. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  901.  
  902. // Set the boundaries for probing (where the probe can reach).
  903. #define LEFT_PROBE_BED_POSITION 60
  904. #define RIGHT_PROBE_BED_POSITION 300
  905. #define FRONT_PROBE_BED_POSITION 60
  906. #define BACK_PROBE_BED_POSITION 271
  907.  
  908. // The Z probe minimum outer margin (to validate G29 parameters).
  909. #define MIN_PROBE_EDGE 20
  910.  
  911. // Probe along the Y axis, advancing X after each column
  912. //#define PROBE_Y_FIRST
  913.  
  914. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  915.  
  916. // Beyond the probed grid, continue the implied tilt?
  917. // Default is to maintain the height of the nearest edge.
  918. //#define EXTRAPOLATE_BEYOND_GRID
  919.  
  920. //
  921. // Experimental Subdivision of the grid by Catmull-Rom method.
  922. // Synthesizes intermediate points to produce a more detailed mesh.
  923. //
  924. //#define ABL_BILINEAR_SUBDIVISION
  925. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  926. // Number of subdivisions between probe points
  927. #define BILINEAR_SUBDIVISIONS 3
  928. #endif
  929.  
  930. #endif
  931.  
  932. #elif ENABLED(AUTO_BED_LEVELING_3POINT)
  933.  
  934. // 3 arbitrary points to probe.
  935. // A simple cross-product is used to estimate the plane of the bed.
  936. #define ABL_PROBE_PT_1_X 20
  937. #define ABL_PROBE_PT_1_Y 20
  938. #define ABL_PROBE_PT_2_X 240
  939. #define ABL_PROBE_PT_2_Y 150
  940. #define ABL_PROBE_PT_3_X 20
  941. #define ABL_PROBE_PT_3_Y 240
  942.  
  943. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  944.  
  945. //===========================================================================
  946. //========================= Unified Bed Leveling ============================
  947. //===========================================================================
  948.  
  949. //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
  950.  
  951. #define MESH_INSET 15 // Mesh inset margin on print area
  952. #define GRID_MAX_POINTS_X 9 // Don't use more than 15 points per axis, implementation limited.
  953. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  954.  
  955. #define UBL_PROBE_PT_1_X 15 // Probing points for 3-Point leveling of the mesh
  956. #define UBL_PROBE_PT_1_Y 15
  957. #define UBL_PROBE_PT_2_X 245
  958. #define UBL_PROBE_PT_2_Y 160
  959. #define UBL_PROBE_PT_3_X 15
  960. #define UBL_PROBE_PT_3_Y 285
  961.  
  962. #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
  963. #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
  964.  
  965. #elif ENABLED(MESH_BED_LEVELING)
  966.  
  967. //===========================================================================
  968. //=================================== Mesh ==================================
  969. //===========================================================================
  970.  
  971. #define MESH_INSET 15 // Mesh inset margin on print area
  972. #define GRID_MAX_POINTS_X 10 // Don't use more than 7 points per axis, implementation limited.
  973. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  974.  
  975. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  976.  
  977. #endif // BED_LEVELING
  978.  
  979. /**
  980. * Use the LCD controller for bed leveling
  981. * Requires MESH_BED_LEVELING or PROBE_MANUALLY
  982. */
  983. //#define LCD_BED_LEVELING
  984.  
  985. #if ENABLED(LCD_BED_LEVELING)
  986. #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
  987. #define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
  988. #endif
  989.  
  990. // Add a menu item to move between bed corners for manual bed adjustment
  991. #define LEVEL_BED_CORNERS
  992.  
  993. /**
  994. * Commands to execute at the end of G29 probing.
  995. * Useful to retract or move the Z probe out of the way.
  996. */
  997. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  998.  
  999.  
  1000. // @section homing
  1001.  
  1002. // The center of the bed is at (X=0, Y=0)
  1003. //#define BED_CENTER_AT_0_0
  1004.  
  1005. // Manually set the home position. Leave these undefined for automatic settings.
  1006. // For DELTA this is the top-center of the Cartesian print volume.
  1007. //#define MANUAL_X_HOME_POS 0
  1008. //#define MANUAL_Y_HOME_POS 0
  1009. //#define MANUAL_Z_HOME_POS 0
  1010.  
  1011. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  1012. //
  1013. // With this feature enabled:
  1014. //
  1015. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  1016. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  1017. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
  1018. // - Prevent Z homing when the Z probe is outside bed area.
  1019. //
  1020. //#define Z_SAFE_HOMING
  1021.  
  1022. #if ENABLED(Z_SAFE_HOMING)
  1023. #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28).
  1024. #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28).
  1025. #endif
  1026.  
  1027. // Homing speeds (mm/m)
  1028. #define HOMING_FEEDRATE_XY (50*50)
  1029. #define HOMING_FEEDRATE_Z (25*30)
  1030.  
  1031. // @section calibrate
  1032.  
  1033. /**
  1034. * Bed Skew Compensation
  1035. *
  1036. * This feature corrects for misalignment in the XYZ axes.
  1037. *
  1038. * Take the following steps to get the bed skew in the XY plane:
  1039. * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
  1040. * 2. For XY_DIAG_AC measure the diagonal A to C
  1041. * 3. For XY_DIAG_BD measure the diagonal B to D
  1042. * 4. For XY_SIDE_AD measure the edge A to D
  1043. *
  1044. * Marlin automatically computes skew factors from these measurements.
  1045. * Skew factors may also be computed and set manually:
  1046. *
  1047. * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
  1048. * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
  1049. *
  1050. * If desired, follow the same procedure for XZ and YZ.
  1051. * Use these diagrams for reference:
  1052. *
  1053. * Y Z Z
  1054. * ^ B-------C ^ B-------C ^ B-------C
  1055. * | / / | / / | / /
  1056. * | / / | / / | / /
  1057. * | A-------D | A-------D | A-------D
  1058. * +-------------->X +-------------->X +-------------->Y
  1059. * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR
  1060. */
  1061. //#define SKEW_CORRECTION
  1062.  
  1063. #if ENABLED(SKEW_CORRECTION)
  1064. // Input all length measurements here:
  1065. #define XY_DIAG_AC 282.8427124746
  1066. #define XY_DIAG_BD 282.8427124746
  1067. #define XY_SIDE_AD 200
  1068.  
  1069. // Or, set the default skew factors directly here
  1070. // to override the above measurements:
  1071. #define XY_SKEW_FACTOR 0.0
  1072.  
  1073. //#define SKEW_CORRECTION_FOR_Z
  1074. #if ENABLED(SKEW_CORRECTION_FOR_Z)
  1075. #define XZ_DIAG_AC 282.8427124746
  1076. #define XZ_DIAG_BD 282.8427124746
  1077. #define YZ_DIAG_AC 282.8427124746
  1078. #define YZ_DIAG_BD 282.8427124746
  1079. #define YZ_SIDE_AD 200
  1080. #define XZ_SKEW_FACTOR 0.0
  1081. #define YZ_SKEW_FACTOR 0.0
  1082. #endif
  1083.  
  1084. // Enable this option for M852 to set skew at runtime
  1085. //#define SKEW_CORRECTION_GCODE
  1086. #endif
  1087.  
  1088. //=============================================================================
  1089. //============================= Additional Features ===========================
  1090. //=============================================================================
  1091.  
  1092. // @section extras
  1093.  
  1094. //
  1095. // EEPROM
  1096. //
  1097. // The microcontroller can store settings in the EEPROM, e.g. max velocity...
  1098. // M500 - stores parameters in EEPROM
  1099. // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
  1100. // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
  1101. //
  1102. #define EEPROM_SETTINGS // Enable for M500 and M501 commands
  1103. //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
  1104. #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
  1105.  
  1106. //
  1107. // Host Keepalive
  1108. //
  1109. // When enabled Marlin will send a busy status message to the host
  1110. // every couple of seconds when it can't accept commands.
  1111. //
  1112. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  1113. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  1114. //#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
  1115.  
  1116. //
  1117. // M100 Free Memory Watcher
  1118. //
  1119. //#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage
  1120.  
  1121. //
  1122. // G20/G21 Inch mode support
  1123. //
  1124. //#define INCH_MODE_SUPPORT
  1125.  
  1126. //
  1127. // M149 Set temperature units support
  1128. //
  1129. //#define TEMPERATURE_UNITS_SUPPORT
  1130.  
  1131. // @section temperature
  1132.  
  1133. // Preheat Constants
  1134. #define PREHEAT_1_TEMP_HOTEND 215
  1135. #define PREHEAT_1_TEMP_BED 70
  1136. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  1137.  
  1138. #define PREHEAT_2_TEMP_HOTEND 255
  1139. #define PREHEAT_2_TEMP_BED 80
  1140. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  1141.  
  1142. /**
  1143. * Nozzle Park
  1144. *
  1145. * Park the nozzle at the given XYZ position on idle or G27.
  1146. *
  1147. * The "P" parameter controls the action applied to the Z axis:
  1148. *
  1149. * P0 (Default) If Z is below park Z raise the nozzle.
  1150. * P1 Raise the nozzle always to Z-park height.
  1151. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  1152. */
  1153. #define NOZZLE_PARK_FEATURE
  1154.  
  1155. #if ENABLED(NOZZLE_PARK_FEATURE)
  1156. // Specify a park position as { X, Y, Z }
  1157. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  1158. #define NOZZLE_PARK_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
  1159. #define NOZZLE_PARK_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
  1160. #endif
  1161.  
  1162. /**
  1163. * Clean Nozzle Feature -- EXPERIMENTAL
  1164. *
  1165. * Adds the G12 command to perform a nozzle cleaning process.
  1166. *
  1167. * Parameters:
  1168. * P Pattern
  1169. * S Strokes / Repetitions
  1170. * T Triangles (P1 only)
  1171. *
  1172. * Patterns:
  1173. * P0 Straight line (default). This process requires a sponge type material
  1174. * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  1175. * between the start / end points.
  1176. *
  1177. * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  1178. * number of zig-zag triangles to do. "S" defines the number of strokes.
  1179. * Zig-zags are done in whichever is the narrower dimension.
  1180. * For example, "G12 P1 S1 T3" will execute:
  1181. *
  1182. * --
  1183. * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  1184. * | | / \ / \ / \ |
  1185. * A | | / \ / \ / \ |
  1186. * | | / \ / \ / \ |
  1187. * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  1188. * -- +--------------------------------+
  1189. * |________|_________|_________|
  1190. * T1 T2 T3
  1191. *
  1192. * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  1193. * "R" specifies the radius. "S" specifies the stroke count.
  1194. * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  1195. *
  1196. * Caveats: The ending Z should be the same as starting Z.
  1197. * Attention: EXPERIMENTAL. G-code arguments may change.
  1198. *
  1199. */
  1200. //#define NOZZLE_CLEAN_FEATURE
  1201.  
  1202. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  1203. // Default number of pattern repetitions
  1204. #define NOZZLE_CLEAN_STROKES 12
  1205.  
  1206. // Default number of triangles
  1207. #define NOZZLE_CLEAN_TRIANGLES 3
  1208.  
  1209. // Specify positions as { X, Y, Z }
  1210. #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  1211. #define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)}
  1212.  
  1213. // Circular pattern radius
  1214. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  1215. // Circular pattern circle fragments number
  1216. #define NOZZLE_CLEAN_CIRCLE_FN 10
  1217. // Middle point of circle
  1218. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  1219.  
  1220. // Moves the nozzle to the initial position
  1221. #define NOZZLE_CLEAN_GOBACK
  1222. #endif
  1223.  
  1224. /**
  1225. * Print Job Timer
  1226. *
  1227. * Automatically start and stop the print job timer on M104/M109/M190.
  1228. *
  1229. * M104 (hotend, no wait) - high temp = none, low temp = stop timer
  1230. * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
  1231. * M190 (bed, wait) - high temp = start timer, low temp = none
  1232. *
  1233. * The timer can also be controlled with the following commands:
  1234. *
  1235. * M75 - Start the print job timer
  1236. * M76 - Pause the print job timer
  1237. * M77 - Stop the print job timer
  1238. */
  1239. #define PRINTJOB_TIMER_AUTOSTART
  1240.  
  1241. /**
  1242. * Print Counter
  1243. *
  1244. * Track statistical data such as:
  1245. *
  1246. * - Total print jobs
  1247. * - Total successful print jobs
  1248. * - Total failed print jobs
  1249. * - Total time printing
  1250. *
  1251. * View the current statistics with M78.
  1252. */
  1253. #define PRINTCOUNTER
  1254.  
  1255. //=============================================================================
  1256. //============================= LCD and SD support ============================
  1257. //=============================================================================
  1258.  
  1259. // @section lcd
  1260.  
  1261. /**
  1262. * LCD LANGUAGE
  1263. *
  1264. * Select the language to display on the LCD. These languages are available:
  1265. *
  1266. * en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, eu, fi, fr, fr_utf8, gl,
  1267. * hr, it, kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8,
  1268. * tr, uk, zh_CN, zh_TW, test
  1269. *
  1270. * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', test':'TEST' }
  1271. */
  1272. #define LCD_LANGUAGE en
  1273.  
  1274. /**
  1275. * LCD Character Set
  1276. *
  1277. * Note: This option is NOT applicable to Graphical Displays.
  1278. *
  1279. * All character-based LCDs provide ASCII plus one of these
  1280. * language extensions:
  1281. *
  1282. * - JAPANESE ... the most common
  1283. * - WESTERN ... with more accented characters
  1284. * - CYRILLIC ... for the Russian language
  1285. *
  1286. * To determine the language extension installed on your controller:
  1287. *
  1288. * - Compile and upload with LCD_LANGUAGE set to 'test'
  1289. * - Click the controller to view the LCD menu
  1290. * - The LCD will display Japanese, Western, or Cyrillic text
  1291. *
  1292. * See http://marlinfw.org/docs/development/lcd_language.html
  1293. *
  1294. * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  1295. */
  1296. #define DISPLAY_CHARSET_HD44780 JAPANESE
  1297.  
  1298. /**
  1299. * LCD TYPE
  1300. *
  1301. * Enable ULTRA_LCD for a 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  1302. * Enable DOGLCD for a 128x64 (ST7565R) Full Graphical Display.
  1303. * (These options will be enabled automatically for most displays.)
  1304. *
  1305. * IMPORTANT: The U8glib library is required for Full Graphic Display!
  1306. * https://github.com/olikraus/U8glib_Arduino
  1307. */
  1308. //#define ULTRA_LCD // Character based
  1309. //#define DOGLCD // Full graphics display
  1310.  
  1311. /**
  1312. * SD CARD
  1313. *
  1314. * SD Card support is disabled by default. If your controller has an SD slot,
  1315. * you must uncomment the following option or it won't work.
  1316. *
  1317. */
  1318. #define SDSUPPORT
  1319.  
  1320. /**
  1321. * SD CARD: SPI SPEED
  1322. *
  1323. * Enable one of the following items for a slower SPI transfer speed.
  1324. * This may be required to resolve "volume init" errors.
  1325. */
  1326. //#define SPI_SPEED SPI_HALF_SPEED
  1327. //#define SPI_SPEED SPI_QUARTER_SPEED
  1328. //#define SPI_SPEED SPI_EIGHTH_SPEED
  1329.  
  1330. /**
  1331. * SD CARD: ENABLE CRC
  1332. *
  1333. * Use CRC checks and retries on the SD communication.
  1334. */
  1335. #define SD_CHECK_AND_RETRY
  1336.  
  1337. //
  1338. // ENCODER SETTINGS
  1339. //
  1340. // This option overrides the default number of encoder pulses needed to
  1341. // produce one step. Should be increased for high-resolution encoders.
  1342. //
  1343. #define ENCODER_PULSES_PER_STEP 4
  1344.  
  1345. //
  1346. // Use this option to override the number of step signals required to
  1347. // move between next/prev menu items.
  1348. //
  1349. #define ENCODER_STEPS_PER_MENU_ITEM 1
  1350.  
  1351. /**
  1352. * Encoder Direction Options
  1353. *
  1354. * Test your encoder's behavior first with both options disabled.
  1355. *
  1356. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1357. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1358. * Reversed Value Editing only? Enable BOTH options.
  1359. */
  1360.  
  1361. //
  1362. // This option reverses the encoder direction everywhere.
  1363. //
  1364. // Set this option if CLOCKWISE causes values to DECREASE
  1365. //
  1366. //#define REVERSE_ENCODER_DIRECTION
  1367.  
  1368. //
  1369. // This option reverses the encoder direction for navigating LCD menus.
  1370. //
  1371. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1372. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1373. //
  1374. //#define REVERSE_MENU_DIRECTION
  1375.  
  1376. //
  1377. // Individual Axis Homing
  1378. //
  1379. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1380. //
  1381. #define INDIVIDUAL_AXIS_HOMING_MENU
  1382.  
  1383. //
  1384. // SPEAKER/BUZZER
  1385. //
  1386. // If you have a speaker that can produce tones, enable it here.
  1387. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1388. //
  1389. #define SPEAKER
  1390.  
  1391. //
  1392. // The duration and frequency for the UI feedback sound.
  1393. // Set these to 0 to disable audio feedback in the LCD menus.
  1394. //
  1395. // Note: Test audio output with the G-Code:
  1396. // M300 S<frequency Hz> P<duration ms>
  1397. //
  1398. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
  1399. //#define LCD_FEEDBACK_FREQUENCY_HZ 1000
  1400.  
  1401. //
  1402. // CONTROLLER TYPE: Standard
  1403. //
  1404. // Marlin supports a wide variety of controllers.
  1405. // Enable one of the following options to specify your controller.
  1406. //
  1407.  
  1408. //
  1409. // ULTIMAKER Controller.
  1410. //
  1411. //#define ULTIMAKERCONTROLLER
  1412.  
  1413. //
  1414. // ULTIPANEL as seen on Thingiverse.
  1415. //
  1416. //#define ULTIPANEL
  1417.  
  1418. //
  1419. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1420. // http://reprap.org/wiki/PanelOne
  1421. //
  1422. //#define PANEL_ONE
  1423.  
  1424. //
  1425. // MaKr3d Makr-Panel with graphic controller and SD support.
  1426. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  1427. //
  1428. //#define MAKRPANEL
  1429.  
  1430. //
  1431. // ReprapWorld Graphical LCD
  1432. // https://reprapworld.com/?products_details&products_id/1218
  1433. //
  1434. //#define REPRAPWORLD_GRAPHICAL_LCD
  1435.  
  1436. //
  1437. // Activate one of these if you have a Panucatt Devices
  1438. // Viki 2.0 or mini Viki with Graphic LCD
  1439. // http://panucatt.com
  1440. //
  1441. //#define VIKI2
  1442. //#define miniVIKI
  1443.  
  1444. //
  1445. // Adafruit ST7565 Full Graphic Controller.
  1446. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1447. //
  1448. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1449.  
  1450. //
  1451. // RepRapDiscount Smart Controller.
  1452. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1453. //
  1454. // Note: Usually sold with a white PCB.
  1455. //
  1456. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1457.  
  1458. //
  1459. // GADGETS3D G3D LCD/SD Controller
  1460. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1461. //
  1462. // Note: Usually sold with a blue PCB.
  1463. //
  1464. //#define G3D_PANEL
  1465.  
  1466. //
  1467. // RepRapDiscount FULL GRAPHIC Smart Controller
  1468. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1469. //
  1470. #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1471.  
  1472. //
  1473. // MakerLab Mini Panel with graphic
  1474. // controller and SD support - http://reprap.org/wiki/Mini_panel
  1475. //
  1476. //#define MINIPANEL
  1477.  
  1478. //
  1479. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  1480. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  1481. //
  1482. // REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
  1483. // is pressed, a value of 10.0 means 10mm per click.
  1484. //
  1485. //#define REPRAPWORLD_KEYPAD
  1486. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0
  1487.  
  1488. //
  1489. // RigidBot Panel V1.0
  1490. // http://www.inventapart.com/
  1491. //
  1492. //#define RIGIDBOT_PANEL
  1493.  
  1494. //
  1495. // BQ LCD Smart Controller shipped by
  1496. // default with the BQ Hephestos 2 and Witbox 2.
  1497. //
  1498. //#define BQ_LCD_SMART_CONTROLLER
  1499.  
  1500. //
  1501. // Cartesio UI
  1502. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1503. //
  1504. //#define CARTESIO_UI
  1505.  
  1506. //
  1507. // ANET and Tronxy Controller supported displays.
  1508. //
  1509. //#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
  1510. // This LCD is known to be susceptible to electrical interference
  1511. // which scrambles the display. Pressing any button clears it up.
  1512. // This is a LCD2004 display with 5 analog buttons.
  1513.  
  1514. //#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  1515. // A clone of the RepRapDiscount full graphics display but with
  1516. // different pins/wiring (see pins_ANET_10.h).
  1517.  
  1518. //
  1519. // LCD for Melzi Card with Graphical LCD
  1520. //
  1521. //#define LCD_FOR_MELZI
  1522.  
  1523. //
  1524. // CONTROLLER TYPE: I2C
  1525. //
  1526. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1527. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1528. //
  1529.  
  1530. //
  1531. // Elefu RA Board Control Panel
  1532. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1533. //
  1534. //#define RA_CONTROL_PANEL
  1535.  
  1536. //
  1537. // Sainsmart YW Robot (LCM1602) LCD Display
  1538. //
  1539. // Note: This controller requires F.Malpartida's LiquidCrystal_I2C library
  1540. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  1541. //
  1542. //#define LCD_I2C_SAINSMART_YWROBOT
  1543.  
  1544. //
  1545. // Generic LCM1602 LCD adapter
  1546. //
  1547. //#define LCM1602
  1548.  
  1549. //
  1550. // PANELOLU2 LCD with status LEDs,
  1551. // separate encoder and click inputs.
  1552. //
  1553. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1554. // For more info: https://github.com/lincomatic/LiquidTWI2
  1555. //
  1556. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1557. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1558. //
  1559. //#define LCD_I2C_PANELOLU2
  1560.  
  1561. //
  1562. // Panucatt VIKI LCD with status LEDs,
  1563. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1564. //
  1565. //#define LCD_I2C_VIKI
  1566.  
  1567. //
  1568. // SSD1306 OLED full graphics generic display
  1569. //
  1570. //#define U8GLIB_SSD1306
  1571.  
  1572. //
  1573. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1574. //
  1575. //#define SAV_3DGLCD
  1576. #if ENABLED(SAV_3DGLCD)
  1577. //#define U8GLIB_SSD1306
  1578. #define U8GLIB_SH1106
  1579. #endif
  1580.  
  1581. //
  1582. // CONTROLLER TYPE: Shift register panels
  1583. //
  1584. // 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1585. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  1586. //
  1587. //#define SAV_3DLCD
  1588.  
  1589. //
  1590. // TinyBoy2 128x64 OLED / Encoder Panel
  1591. //
  1592. //#define OLED_PANEL_TINYBOY2
  1593.  
  1594. //
  1595. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  1596. // https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html
  1597. //
  1598. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  1599.  
  1600. //
  1601. // MKS MINI12864 with graphic controller and SD support
  1602. // http://reprap.org/wiki/MKS_MINI_12864
  1603. //
  1604. //#define MKS_MINI_12864
  1605.  
  1606. //
  1607. // Factory display for Creality CR-10
  1608. // https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html
  1609. //
  1610. // This is RAMPS-compatible using a single 10-pin connector.
  1611. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  1612. //
  1613. //#define CR10_STOCKDISPLAY
  1614.  
  1615. //
  1616. // MKS OLED 1.3" 128x64 FULL GRAPHICS CONTROLLER
  1617. // http://reprap.org/wiki/MKS_12864OLED
  1618. //
  1619. // Tiny, but very sharp OLED display
  1620. // If there is a pixel shift, try the other controller.
  1621. //
  1622. //#define MKS_12864OLED // Uses the SH1106 controller (default)
  1623. //#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller
  1624.  
  1625. // Silvergate GLCD controller
  1626. // http://github.com/android444/Silvergate
  1627. //
  1628. //#define SILVER_GATE_GLCD_CONTROLLER
  1629.  
  1630. //=============================================================================
  1631. //=============================== Extra Features ==============================
  1632. //=============================================================================
  1633.  
  1634. // @section extras
  1635.  
  1636. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  1637. //#define FAST_PWM_FAN
  1638.  
  1639. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  1640. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  1641. // is too low, you should also increment SOFT_PWM_SCALE.
  1642. //#define FAN_SOFT_PWM
  1643.  
  1644. // Incrementing this by 1 will double the software PWM frequency,
  1645. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  1646. // However, control resolution will be halved for each increment;
  1647. // at zero value, there are 128 effective control positions.
  1648. #define SOFT_PWM_SCALE 0
  1649.  
  1650. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  1651. // be used to mitigate the associated resolution loss. If enabled,
  1652. // some of the PWM cycles are stretched so on average the desired
  1653. // duty cycle is attained.
  1654. //#define SOFT_PWM_DITHER
  1655.  
  1656. // Temperature status LEDs that display the hotend and bed temperature.
  1657. // If all hotends, bed temperature, and target temperature are under 54C
  1658. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  1659. //#define TEMP_STAT_LEDS
  1660.  
  1661. // M240 Triggers a camera by emulating a Canon RC-1 Remote
  1662. // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
  1663. //#define PHOTOGRAPH_PIN 23
  1664.  
  1665. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  1666. //#define SF_ARC_FIX
  1667.  
  1668. // Support for the BariCUDA Paste Extruder
  1669. //#define BARICUDA
  1670.  
  1671. // Support for BlinkM/CyzRgb
  1672. //#define BLINKM
  1673.  
  1674. // Support for PCA9632 PWM LED driver
  1675. //#define PCA9632
  1676.  
  1677. /**
  1678. * RGB LED / LED Strip Control
  1679. *
  1680. * Enable support for an RGB LED connected to 5V digital pins, or
  1681. * an RGB Strip connected to MOSFETs controlled by digital pins.
  1682. *
  1683. * Adds the M150 command to set the LED (or LED strip) color.
  1684. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  1685. * luminance values can be set from 0 to 255.
  1686. * For Neopixel LED an overall brightness parameter is also available.
  1687. *
  1688. * *** CAUTION ***
  1689. * LED Strips require a MOFSET Chip between PWM lines and LEDs,
  1690. * as the Arduino cannot handle the current the LEDs will require.
  1691. * Failure to follow this precaution can destroy your Arduino!
  1692. * NOTE: A separate 5V power supply is required! The Neopixel LED needs
  1693. * more current than the Arduino 5V linear regulator can produce.
  1694. * *** CAUTION ***
  1695. *
  1696. * LED Type. Enable only one of the following two options.
  1697. *
  1698. */
  1699. //#define RGB_LED
  1700. //#define RGBW_LED
  1701.  
  1702. #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
  1703. #define RGB_LED_R_PIN 34
  1704. #define RGB_LED_G_PIN 43
  1705. #define RGB_LED_B_PIN 35
  1706. #define RGB_LED_W_PIN -1
  1707. #endif
  1708.  
  1709. // Support for Adafruit Neopixel LED driver
  1710. //#define NEOPIXEL_LED
  1711. #if ENABLED(NEOPIXEL_LED)
  1712. #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  1713. #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
  1714. #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
  1715. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  1716. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
  1717. //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
  1718. #endif
  1719.  
  1720. /**
  1721. * Printer Event LEDs
  1722. *
  1723. * During printing, the LEDs will reflect the printer status:
  1724. *
  1725. * - Gradually change from blue to violet as the heated bed gets to target temp
  1726. * - Gradually change from violet to red as the hotend gets to temperature
  1727. * - Change to white to illuminate work surface
  1728. * - Change to green once print has finished
  1729. * - Turn off after the print has finished and the user has pushed a button
  1730. */
  1731. #if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
  1732. #define PRINTER_EVENT_LEDS
  1733. #endif
  1734.  
  1735. /**
  1736. * R/C SERVO support
  1737. * Sponsored by TrinityLabs, Reworked by codexmas
  1738. */
  1739.  
  1740. /**
  1741. * Number of servos
  1742. *
  1743. * For some servo-related options NUM_SERVOS will be set automatically.
  1744. * Set this manually if there are extra servos needing manual control.
  1745. * Leave undefined or set to 0 to entirely disable the servo subsystem.
  1746. */
  1747. #define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  1748.  
  1749. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
  1750. // 300ms is a good value but you can try less delay.
  1751. // If the servo can't reach the requested position, increase it.
  1752. #define SERVO_DELAY { 300, 300, 300 }
  1753.  
  1754. // Servo deactivation
  1755. //
  1756. // With this option servos are powered only during movement, then turned off to prevent jitter.
  1757. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  1758.  
  1759. #endif // CONFIGURATION_H
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!