U-Boot 2017.07-28633-g1530219 (Dec 28 2017 - 12:46:38 -0800), Build: jenkins-uboot_v2017.07-59
CPU:   Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: nitrogen6_max
I2C:   ready
DRAM:  3.8 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected gd25q16c with page size 256 Bytes, erase size 4 KiB, total 2 MiB
Display: lvds:XGA (1024x768)
In:    serial
Out:   serial
Err:   serial
Net:   Micrel ksz9021 at 6
FEC [PRIME], usb_ether
Hit any key to stop autoboot:  0
=> env default -a
## Resetting to default environment
=> savee
Saving Environment to SPI Flash...
SF: Detected gd25q16c with page size 256 Bytes, erase size 4 KiB, total 2 MiB
Erasing SPI flash...Writing to SPI flash...done
=> run upgradeu
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /upgrade.scr
5803 bytes read in 6 ms (944.3 KiB/s)
## Executing script at 10008000
: No match
: No match
SF: Detected gd25q16c with page size 256 Bytes, erase size 4 KiB, total 2 MiB
probed SPI ROM
check U-Boot
482304 bytes read in 29 ms (15.9 MiB/s)
read 75c00 bytes from SD card
device 0 offset 0x400, size 0x75c00
SF: 482304 bytes @ 0x400 Read: OK
byte at 0x12000425 (0x60) != byte at 0x12400425 (0x10)
Total of 37 byte(s) were the same
Need U-Boot upgrade
Program in 5 seconds
5
4
3
2
1
erasing
SF: 786432 bytes @ 0x0 Erased: OK
programming
device 0 offset 0x800, size 0x75800
SF: 481280 bytes @ 0x800 Written: OK
device 0 offset 0x400, size 0x400
SF: 1024 bytes @ 0x400 Written: OK
verifying
device 0 offset 0x400, size 0x75c00
SF: 482304 bytes @ 0x400 Read: OK
Total of 482304 byte(s) were the same
---- U-Boot upgraded. The board will now reset.
resetting ...
U-Boot 2020.10-53215-g3d5e7f6023 (Mar 03 2022 - 09:13:54 -0800), Build: jenkins-uboot_v2020.10-200
CPU:   i.MX6Q rev1.2 at 792 MHz
Reset cause: WDOG
Board: nitrogen6_max
I2C:   ready
DRAM:
U-Boot 2020.10-53215-g3d5e7f6023 (Mar 03 2022 - 09:13:54 -0800), Build: jenkins-uboot_v2020.10-200
CPU:   i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: nitrogen6_max
I2C:   ready
DRAM:
U-Boot 2020.10-53215-g3d5e7f6023 (Mar 03 2022 - 09:13:54 -0800), Build: jenkins-uboot_v2020.10-200
CPU:   i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: nitrogen6_max
I2C:   ready
DRAM:
U-Boot 2020.10-53215-g3d5e7f6023 (Mar 03 2022 - 09:13:54 -0800), Build: jenkins-uboot_v2020.10-200
CPU:   i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: nitrogen6_max
I2C:   ready
DRAM: