daily pastebin goal
85%
SHARE
TWEET

IceTV Skippa boot log

a guest Jun 20th, 2016 262 Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1.  
  2. BCM74290010
  3.  
  4. M0SCZSL2=1
  5. LLMB=0000C000
  6. BP=02000000
  7. L2Cfg=1E7AD627
  8. L2Buf=77707711
  9. BrCfg=F01C200E
  10. BrMod=02800801
  11. BrZp0=44000000
  12. BrZp1=00002000
  13. #@ReShmoo MEMC0
  14.  
  15. Bad block scanned...
  16.  
  17. CPU speed:            1305MHz
  18. DDR Frequency:        928 MHz
  19. DDR Mode:             DDR3
  20. Total memory(MEMC 0): 1024MB
  21. MEMC 0 DDR Width:     32
  22. Boot Device:          NAND
  23. ECC Level: 4
  24. Total flash:          256MB
  25. RTS VERSION:          20130520182531_7241
  26. ETH0_PHY:             INT
  27. ETH0_MDIO_MODE:       1
  28. ETH0_SPEED:           100
  29. ETH0_PHYADDR:         1
  30.  
  31. Initializing USB.
  32.  
  33. CFE initialized.
  34. Starting splash screen.
  35. Found splash image - Width = 720 Height = 576
  36.  
  37. USB: New low speed device connected to bus 3 hub 1 port 1
  38. USB: Locating Class 03 Vendor 046D Product C30B: Human-Interface Device
  39. USBHID: Keyboard Configured.
  40.  
  41. USB: New high speed device connected to bus 6 hub 1 port 1
  42. Driver not found.
  43.     SERIALNUMBER = 754715060092208
  44.  
  45. -enc option is enabled.....
  46. Loader:elf Filesys:raw Dev:flash0.image0 File: Options:bmem=160M@96M bmem=256M@512M
  47. Loading:
  48. Image Size[70424288]
  49. 0x80000000/70424288
  50. Image Successfully Authenticated!
  51. 0x8419e600/127408
  52. BOOT EPT[804e2040]
  53.  
  54.  ***command status = 0
  55.  
  56. Entry address is 0x804e2040
  57. Starting program at 0x804e2040
  58.  
  59. Linux version 3.3.8-3.3-svn9941 (oelof.kuiper@UECAUBLD02.au.uectech.net) (gcc version 4.5.4 (Broadcom stbgcc-4.5.4-2.8) ) #15 SMP Tue Sep 22 13:23:03 EST 2015
  60. Fetching vars from bootloader... found 11 vars.
  61. Options: moca=0 sata=1 pcie=0 usb=1
  62. Using 1024 MB + 0 MB RAM (from CFE)
  63. bootconsole [early0] enabled
  64. CPU revision is: 00025a11 (Broadcom BMIPS5000)
  65. FPU revision is: 00130001
  66. Determined physical RAM map:
  67.  memory: 10000000 @ 00000000 (usable)
  68.  memory: 30000000 @ 20000000 (usable)
  69. bmem: adding 160 MB RESERVED region at 96 MB (0x0a000000@0x06000000)
  70. bmem: adding 256 MB RESERVED region at 512 MB (0x10000000@0x20000000)
  71. Initrd not found or empty - disabling initrd
  72. Zone PFN ranges:
  73.   Normal   0x00000000 -> 0x00050000
  74. Movable zone start PFN for each node
  75. Early memory PFN ranges
  76.     0: 0x00000000 -> 0x00010000
  77.     0: 0x00020000 -> 0x00050000
  78. PERCPU: Embedded 7 pages/cpu @84bd1000 s5632 r8192 d14848 u32768
  79. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 259584
  80. Kernel command line: bmem=160M@96M bmem=256M@512M
  81. PID hash table entries: 4096 (order: 2, 16384 bytes)
  82. Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  83. Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  84. Primary instruction cache 32kB, physically tagged, 4-way, linesize 64 bytes.
  85. Primary data cache 32kB, 4-way, linesize 32 bytes.
  86. MIPS secondary cache 256kB, 8-way, linesize 128 bytes.
  87. Memory: 544144k/1048576k available (5080k kernel code, 504432k reserved, 1265k data, 60844k init, 0k highmem)
  88. Hierarchical RCU implementation.
  89. NR_IRQS:160
  90. Measuring MIPS counter frequency...
  91. Detected MIPS clock frequency: 1305 MHz (163.125 MHz counter)
  92. Console: colour dummy device 80x25
  93. Calibrating delay loop... 869.37 BogoMIPS (lpj=434688)
  94. pid_max: default: 32768 minimum: 301
  95. Mount-cache hash table entries: 512
  96. SMP: Booting CPU1...
  97. CPU revision is: 00025a11 (Broadcom BMIPS5000)
  98. FPU revision is: 00130001
  99. Primary instruction cache 32kB, physically tagged, 4-way, linesize 64 bytes.
  100. Primary data cache 32kB, 4-way, linesize 32 bytes.
  101. MIPS secondary cache 256kB, 8-way, linesize 128 bytes.
  102. SMP: CPU1 is running
  103. Brought up 2 CPUs
  104. NET: Registered protocol family 16
  105. USB0: power enable is active high; overcurrent is active low
  106. USB1: power enable is active high; overcurrent is active low
  107. bio: create slab <bio-0> at 0
  108. SCSI subsystem initialized
  109. usbcore: registered new interface driver usbfs
  110. usbcore: registered new interface driver hub
  111. usbcore: registered new device driver usb
  112. cfg80211: Calling CRDA to update world regulatory domain
  113. Switching to clocksource wktmr
  114. NET: Registered protocol family 2
  115. IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
  116. TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
  117. TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
  118. TCP: Hash tables configured (established 131072 bind 65536)
  119. TCP reno registered
  120. UDP hash table entries: 512 (order: 2, 16384 bytes)
  121. UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  122. NET: Registered protocol family 1
  123. RPC: Registered named UNIX socket transport module.
  124. RPC: Registered udp transport module.
  125. RPC: Registered tcp transport module.
  126. RPC: Registered tcp NFSv4.1 backchannel transport module.
  127. squashfs: version 4.0 (2009/01/31) Phillip Lougher
  128. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
  129. fuse init (API version 7.18)
  130. msgmni has been set to 1062
  131. io scheduler noop registered
  132. io scheduler cfq registered (default)
  133. Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
  134. console [ttyS0] enabled, bootconsole disabled 52) is a 16550A
  135. console [ttyS0] enabled, bootconsole disabled
  136. serial8250.0: ttyS1 at MMIO 0x10406740 (irq = 53) is a 16550A
  137. serial8250.0: ttyS2 at MMIO 0x10406780 (irq = 54) is a 16550A
  138. brd: module loaded
  139. loop: module loaded
  140. ahci: SSS flag set, parallel bus scan disabled
  141. ahci strict-ahci.0: AHCI 0001.0300 32 slots 3 ports 6 Gbps 0x3 impl platform mode
  142. ahci strict-ahci.0: flags: sntf stag clo pmp slum part
  143. scsi0 : ahci_platform
  144. scsi1 : ahci_platform
  145. scsi2 : ahci_platform
  146. ata1: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x100 irq 33
  147. ata2: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x180 irq 33
  148. ata3: DUMMY
  149. brcmstb_nand: NAND controller driver is loaded
  150. bcmgenet: configuring instance #0 for internal PHY
  151. bcmgenet bcmgenet.0: eth0: link down
  152. No PHY detected, not registering interface:1
  153. ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
  154. bcmgenet: probe of bcmgenet.1 failed with error -5
  155. ata1.00: ATA-9: WDC WD10JUCT-63CYNY0, 01.01A01, max UDMA/133
  156. ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32)
  157. usbcore: registered new interface driver rtl8192cu
  158. pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
  159. ata1.00: configured for UDMA/133
  160. scsi 0:0:0:0: Direct-Access     ATA      WDC WD10JUCT-63C 01.0 PQ: 0 ANSI: 5
  161. usbcore: registered new interface driver pegasus
  162. usbcore: registered new interface driver asix
  163. usbcore: registered new interface driver cdc_ether
  164. sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
  165. sd 0:0:0:0: Attached scsi generic sg0 type 0
  166. usbcore: registered new interface driver net1080
  167. usbcore: registered new interface driver cdc_subset
  168. usbcore: registered new interface driver zaurus
  169. usbcore: registered new interface driver cdc_ncm
  170. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  171. ehci-brcm ehci-brcm.0: Broadcom STB EHCI
  172. ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
  173. sd 0:0:0:0: [sda] 4096-byte physical blocks
  174. ehci-brcm ehci-brcm.0: irq 56, io mem 0x10480300
  175. sd 0:0:0:0: [sda] Write Protect is off
  176. ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
  177. hub 1-0:1.0: USB hub found
  178. hub 1-0:1.0: 1 port detected
  179. ehci-brcm ehci-brcm.1: Broadcom STB EHCI
  180. ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
  181. sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
  182. ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
  183. ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
  184. hub 2-0:1.0: USB hub found
  185. hub 2-0:1.0: 1 port detected
  186.  sda: sda1
  187. ehci-brcm ehci-brcm.2: Broadcom STB EHCI
  188. ehci-brcm ehci-brcm.2: new USB bus registered, assigned bus number 3
  189. sd 0:0:0:0: [sda] Attached SCSI disk
  190. ehci-brcm ehci-brcm.2: irq 61, io mem 0x10490300
  191. ehci-brcm ehci-brcm.2: USB 0.0 started, EHCI 1.00
  192. hub 3-0:1.0: USB hub found
  193. hub 3-0:1.0: 1 port detected
  194. ehci-brcm ehci-brcm.3: Broadcom STB EHCI
  195. ehci-brcm ehci-brcm.3: new USB bus registered, assigned bus number 4
  196. ehci-brcm ehci-brcm.3: irq 62, io mem 0x10490500
  197. ehci-brcm ehci-brcm.3: USB 0.0 started, EHCI 1.00
  198. hub 4-0:1.0: USB hub found
  199. hub 4-0:1.0: 1 port detected
  200. ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  201. ohci-brcm ohci-brcm.0: Broadcom STB OHCI
  202. ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 5
  203. ohci-brcm ohci-brcm.0: irq 58, io mem 0x10480400
  204. hub 5-0:1.0: USB hub found
  205. hub 5-0:1.0: 1 port detected
  206. ohci-brcm ohci-brcm.1: Broadcom STB OHCI
  207. ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 6
  208. ohci-brcm ohci-brcm.1: irq 59, io mem 0x10480600
  209. hub 6-0:1.0: USB hub found
  210. ata2: SATA link down (SStatus 0 SControl 300)
  211. hub 6-0:1.0: 1 port detected
  212. ohci-brcm ohci-brcm.2: Broadcom STB OHCI
  213. ohci-brcm ohci-brcm.2: new USB bus registered, assigned bus number 7
  214. ohci-brcm ohci-brcm.2: irq 63, io mem 0x10490400
  215. hub 7-0:1.0: USB hub found
  216. hub 7-0:1.0: 1 port detected
  217. ohci-brcm ohci-brcm.3: Broadcom STB OHCI
  218. ohci-brcm ohci-brcm.3: new USB bus registered, assigned bus number 8
  219. ohci-brcm ohci-brcm.3: irq 64, io mem 0x10490600
  220. usb 4-1: new high-speed USB device number 2 using ehci-brcm
  221. hub 8-0:1.0: USB hub found
  222. hub 8-0:1.0: 1 port detected
  223. Initializing USB Mass Storage driver...
  224. usbcore: registered new interface driver usb-storage
  225. USB Mass Storage support registered.
  226. mousedev: PS/2 mouse device common for all mice
  227. UEC Frontpanel driver loaded.
  228. input: gpio-keys as /devices/virtual/input/input0
  229. usbcore: registered new interface driver usbhid
  230. usbhid: USB HID core driver
  231. TCP cubic registered
  232. NET: Registered protocol family 17
  233. lib80211: common routines for IEEE802.11 drivers
  234. PM: CP0 COUNT/COMPARE frequency does not depend on divisor
  235. EBI CS0: setting up NAND flash (primary)
  236. ONFI param page 0 valid
  237. ONFI flash detected
  238. NAND device: Manufacturer ID: 0xef, Chip ID: 0xda (Unknown W29N02GV)
  239. ONFI param page 0 valid
  240. ONFI flash detected
  241. NAND device: Manufacturer ID: 0xef, Chip ID: 0xda (Unknown W29N02GV)
  242. brcmnand brcmnand.0: 256MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4
  243.  
  244. Bad block table found at page 131008, version 0x01
  245. Bad block table found at page 130944, version 0x01
  246. nand_read_bbt: bad block at 0x000001400000
  247. nand_read_bbt: bad block at 0x000001440000
  248. nand_read_bbt: bad block at 0x000003140000
  249. nand_read_bbt: bad block at 0x0000051c0000
  250. nand_read_bbt: bad block at 0x000005600000
  251. nand_read_bbt: bad block at 0x000006e80000
  252. nand_read_bbt: bad block at 0x00000cdc0000
  253. Creating 8 MTD partitions on "brcmnand.0":
  254. 0x000000000000-0x000000280000 : "cfe"
  255. 0x000000280000-0x000000300000 : "nvram"
  256. 0x000000300000-0x000000480000 : "splash0"
  257. 0x000000480000-0x000000580000 : "splash1"
  258. 0x000000580000-0x000006980000 : "image0"
  259. 0x000006980000-0x00000cd80000 : "image1"
  260. 0x00000cd80000-0x00000ff80000 : "home"
  261. 0x00000ff80000-0x000010000000 : "reserved"
  262. Warning: unable to open an initial console.
  263. Freeing unused kernel memory: 60844k freed
  264. usb 6-1: new low-speed USB device number 2 using ohci-brcm
  265.  
  266. UBI: attaching mtd6 to ubi0
  267. UBI: physical eraseblock size:   131072 bytes (128 KiB)
  268. UBI: logical eraseblock size:    126976 bytes
  269. UBI: smallest flash I/O unit:    2048
  270. UBI: VID header offset:          2048 (aligned 2048)
  271. UBI: data offset:                4096
  272. input: Logitech NetPlay Keyboard as /devices/platform/ohci-brcm.1/usb6/6-1/6-1:1.0/input/input1
  273. generic-usb 0003:046D:C30B.0001: input: USB HID v1.10 Keyboard [Logitech NetPlay Keyboard] on usb-ohci_hcd-1/input0
  274. UBI: max. sequence number:       288
  275. UBI: attached mtd6 to ubi0
  276. UBI: MTD device name:            "home"
  277. UBI: MTD device size:            50 MiB
  278. UBI: number of good PEBs:        399
  279. UBI: number of bad PEBs:         1
  280. UBI: number of corrupted PEBs:   0
  281. UBI: max. allowed volumes:       128
  282. UBI: wear-leveling threshold:    4096
  283. UBI: number of internal volumes: 1
  284. UBI: number of user volumes:     1
  285. UBI: available PEBs:             0
  286. UBI: total number of reserved PEBs: 399
  287. UBI: number of PEBs reserved for bad PEB handling: 3
  288. UBI: max/mean erase counter: 3/1
  289. UBI: image sequence number:  -860116158
  290. UBI: background thread "ubi_bgt0d" started, PID 589
  291. UBI device number 0, total 399 LEBs (50663424 bytes, 48.3 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
  292. ubimkvol: error!: UBI device does not have free logical eraseblocks
  293. UBIFS: recovery needed
  294. UBIFS: recovery completed
  295. UBIFS: mounted UBI device 0, volume 0, name "root"
  296. UBIFS: file system size:   48631808 bytes (47492 KiB, 46 MiB, 383 LEBs)
  297. UBIFS: journal size:       2412544 bytes (2356 KiB, 2 MiB, 19 LEBs)
  298. UBIFS: media format:       w4/r0 (latest is w4/r0)
  299. UBIFS: default compressor: lzo
  300. UBIFS: reserved for root:  2297000 bytes (2243 KiB)
  301. Configuring eth0 interface
  302. Configuring lo interface
  303. Configuring wlan0 interface
  304. Starting local services
  305. EXT4-fs (sda1): recovery complete
  306. EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
  307. create root cache and thumbnail folders
  308. Starting Network
  309. Configuring wlan0 using UI prefs
  310. cat: can't open '/tmp/wpa.wlan0.pid': No such file or directory
  311. rfkill: Cannot open RFKILL control device
  312. ioctl[SIOCSIWAP]: Operation not permitted
  313. Waiting for network
  314. udhcpc (v1.19.4) started
  315. Sending discover...
  316. Copying DLNA images
  317. cp: can't stat '/usr/local/bin/amp/img/DLNA/*': No such file or directory
  318. 1
  319. bcmdriver: module license 'Proprietary' taints kernel.
  320. Disabling lock debugging due to kernel taint
  321. BCMDRV: Initializing bcmdriver version $ $
  322. BCMDRV: Total intc words=3,Total Irqs=97
  323. BCMDRV: Initialization complete
  324. Sending discover...
  325. Sending discover...
  326. Sending discover...
  327. Sending discover...
  328. Sending discover...
RAW Paste Data
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy. OK, I Understand
 
Top