idf.py flash monitor

C:\Espressif\frameworks\esp-idf-v4.4\my_project>idf.py flash monitor
Executing action: flash
Serial port COM7
Connecting....
Detecting chip type... Unsupported detection protocol, switching and trying again...
Connecting....
Detecting chip type... ESP32
Running ninja in directory c:\espressif\frameworks\esp-idf-v4.4\my_project\build
Executing "ninja flash"...
[1/5] cmd.exe /C "cd /D C:\Espressif\frameworks\esp-idf-v4...frameworks/esp-idf-v4.4/my_project/build/app-template.bin"
app-template.bin binary size 0x83c40 bytes. Smallest app partition is 0x100000 bytes. 0x7c3c0 bytes (49%) free.
[2/5] Performing build step for 'bootloader'
[1/1] cmd.exe /C "cd /D C:\Espressif\frameworks\esp-idf-v4.4\my_project\build\bootloader\esp-idf\esptool_py && C:\Espressif\python_env\idf4.4_py3.8_env\Scripts\python.exe C:/Espressif/frameworks/esp-idf-v4.4/components/partition_table/check_sizes.py --offset 0x8000 bootloader 0x1000 C:/Espressif/frameworks/esp-idf-v4.4/my_project/build/bootloader/bootloader.bin"
Bootloader binary size 0x62b0 bytes. 0xd50 bytes (12%) free.
[2/3] cmd.exe /C "cd /D C:\Espressif\frameworks\esp-idf-v4.../esp-idf-v4.4/components/esptool_py/run_serial_tool.cmake"
esptool.py esp32 -p COM7 -b 460800 --before=default_reset --after=hard_reset write_flash --flash_mode dio --flash_freq 40m --flash_size 4MB 0x1000 bootloader/bootloader.bin 0x10000 app-template.bin 0x8000 partition_table/partition-table.binesptool.py v3.2-dev
Serial port COM7
Connecting....
Chip is ESP32-D0WDQ6 (revision 1)
Features: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None
Crystal is 40MHz
MAC: 58:bf:25:93:c9:00
Uploading stub...
Running stub...
Stub running...
Changing baud rate to 460800
Changed.
Configuring flash size...
Flash will be erased from 0x00001000 to 0x00007fff...
Flash will be erased from 0x00010000 to 0x00093fff...
Flash will be erased from 0x00008000 to 0x00008fff...
Compressed 25264 bytes to 15790...
Writing at 0x00001000... (100 %)
Wrote 25264 bytes (15790 compressed) at 0x00001000 in 0.7 seconds (effective 301.9 kbit/s)...
Hash of data verified.
Compressed 539712 bytes to 324436...
Writing at 0x00010000... (5 %)
Writing at 0x0001ae63... (10 %)
Writing at 0x00028145... (15 %)
Writing at 0x0002f85b... (20 %)
Writing at 0x000353a9... (25 %)
Writing at 0x0003b10c... (30 %)
Writing at 0x000405d1... (35 %)
Writing at 0x000459f0... (40 %)
Writing at 0x0004ad71... (45 %)
Writing at 0x00050b9e... (50 %)
Writing at 0x00056e7b... (55 %)
Writing at 0x0005cd58... (60 %)
Writing at 0x00062857... (65 %)
Writing at 0x00068076... (70 %)
Writing at 0x0006dc7d... (75 %)
Writing at 0x00074037... (80 %)
Writing at 0x0007df57... (85 %)
Writing at 0x00084049... (90 %)
Writing at 0x00089c6e... (95 %)
Writing at 0x0008f193... (100 %)
Wrote 539712 bytes (324436 compressed) at 0x00010000 in 8.0 seconds (effective 542.6 kbit/s)...
Hash of data verified.
Compressed 3072 bytes to 103...
Writing at 0x00008000... (100 %)
Wrote 3072 bytes (103 compressed) at 0x00008000 in 0.1 seconds (effective 335.6 kbit/s)...
Hash of data verified.

Leaving...
Hard resetting via RTS pin...
Executing action: monitor
Serial port COM7
Connecting.....
Detecting chip type... Unsupported detection protocol, switching and trying again...
Connecting.....
Detecting chip type... ESP32
Running idf_monitor in directory c:\espressif\frameworks\esp-idf-v4.4\my_project
Executing "C:\Espressif\python_env\idf4.4_py3.8_env\Scripts\python.exe C:\Espressif\frameworks\esp-idf-v4.4\tools/idf_monitor.py -p COM7 -b 115200 --toolchain-prefix xtensa-esp32-elf- --target esp32 --revision 0 c:\espressif\frameworks\esp-idf-v4.4\my_project\build\app-template.elf -m 'C:\Espressif\python_env\idf4.4_py3.8_env\Scripts\python.exe' 'C:\Espressif\frameworks\esp-idf-v4.4\tools\idf.py'"...
--- WARNING: GDB cannot open serial ports accessed as COMx
--- Using \\.\COM7 instead...
--- idf_monitor on \\.\COM7 115200 ---
--- Quit: Ctrl+] | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
ets Jun  8 2016 00:22:57

rst:0x1 (POWERON_RESET),boot:0x12 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:6612
load:0x40078000,len:14780
load:0x40080400,len:3784
0x40080400: _init at ??:?

entry 0x40080694
I (27) boot: ESP-IDF v4.4 2nd stage bootloader
I (27) boot: compile time 14:13:41
I (27) boot: chip revision: 1
I (30) boot_comm: chip revision: 1, min. bootloader chip revision: 0
I (37) boot.esp32: SPI Speed      : 40MHz
I (41) boot.esp32: SPI Mode       : DIO
I (46) boot.esp32: SPI Flash Size : 4MB
I (50) boot: Enabling RNG early entropy source...
I (56) boot: Partition Table:
I (59) boot: ## Label            Usage          Type ST Offset   Length
I (67) boot:  0 nvs              WiFi data        01 02 00009000 00006000
I (74) boot:  1 phy_init         RF data          01 01 0000f000 00001000
I (82) boot:  2 factory          factory app      00 00 00010000 00100000
I (89) boot: End of partition table
I (93) boot_comm: chip revision: 1, min. application chip revision: 0
I (100) esp_image: segment 0: paddr=00010020 vaddr=3f400020 size=16dc8h ( 93640) map
I (143) esp_image: segment 1: paddr=00026df0 vaddr=3ffbdb60 size=04474h ( 17524) load
I (150) esp_image: segment 2: paddr=0002b26c vaddr=40080000 size=04dach ( 19884) load
I (158) esp_image: segment 3: paddr=00030020 vaddr=400d0020 size=51398h (332696) map
I (279) esp_image: segment 4: paddr=000813c0 vaddr=40084dac size=1283ch ( 75836) load
I (310) esp_image: segment 5: paddr=00093c04 vaddr=50000000 size=00010h (    16) load
I (322) boot: Loaded app from partition at offset 0x10000
I (322) boot: Disabling RNG early entropy source...
I (334) cpu_start: Pro cpu up.
I (334) cpu_start: Starting app cpu, entry point is 0x40081340
0x40081340: call_start_cpu1 at C:/Espressif/frameworks/esp-idf-v4.4/components/esp_system/port/cpu_start.c:156

I (0) cpu_start: App cpu up.
I (350) cpu_start: Pro cpu start user code
I (350) cpu_start: cpu freq: 160000000
I (350) cpu_start: Application information:
I (355) cpu_start: Project name:     app-template
I (360) cpu_start: App version:      release_v1.2.3-3-ge7708e7
I (367) cpu_start: Compile time:     Mar 24 2022 14:13:02
I (373) cpu_start: ELF file SHA256:  4532b029153834b3...
I (379) cpu_start: ESP-IDF:          v4.4
I (384) heap_init: Initializing. RAM available for dynamic allocation:
I (391) heap_init: At 3FFAFF10 len 000000F0 (0 KiB): DRAM
I (397) heap_init: At 3FFB6388 len 00001C78 (7 KiB): DRAM
I (403) heap_init: At 3FFB9A20 len 00004108 (16 KiB): DRAM
I (409) heap_init: At 3FFCF780 len 00010880 (66 KiB): DRAM
I (415) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM
I (421) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM
I (428) heap_init: At 400975E8 len 00008A18 (34 KiB): IRAM
I (435) spi_flash: detected chip: generic
Bluepad32 (C) 2016-2022 Ricardo Quesada and contributors.
Version: v3.0.1
BTStack: Copyright (C) 2017 BlueKitchen GmbH.
Platform: Arduino
Gap security level: 2
Periodic Inquiry: max=5, min=4, len=3
Max connected gamepads: 4
I (509) BTDM_INIT: BT controller compile version [6a07b06]
I (509) system_api: Base MAC address is not set
I (519) system_api: read default base MAC address from EFUSE
I (529) phy_init: phy_version 4670,719f9f6,Feb 18 2021,17:07:07
W (529) phy_init: failed to load RF calibration data (0x1102), falling back to full calibration
BTstack up and running at 58:BF:25:93:C9:02
HCI not ready, cannot send packet, will again try later. Current state idx=1
HCI not ready, cannot send packet, will Firmware: Bluepad32 for Arduino v3.0.1