u-boot mxq pro

INFO:    PSCI Affinity Map:
INFO:      AffInst: Level 0, MPID 0x0, State ON
INFO:      AffInst: Level 0, MPID 0x1, State OFF
INFO:      AffInst: Level 0, MPID 0x2, State OFF
INFO:      AffInst: Level 0, MPID 0x3, State OFF
bl31 reb�GXBB:BL1:08dafd:0a8993;FEAT:EDFC318C;POC:3;RCY:0;EMMC:800;NAND:0;READ:0;CHK:0;
TE: 34022
no sdio debug board detected

BL2 Built : 13:55:05, Jan 28 2016.
gxb g3625dd5 - xiaobo.gu@droid05

Board ID = 2
set vcck to 1100 mv
set vddee to 1000 mv
CPU clk: 1536MHz
DDR channel setting: DDR0 Rank0+1 same
DDR0: 1024MB(auto) @ 792MHz(2T)-11
DataBus test pass!
AddrBus test pass!
NAND init
Load fip header from NAND, src: 0x0000c000, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from NAND, src: 0x00010000, des: 0x01000000, size: 0x00008440
Sending bl30..................................OK.
Run bl30...
Load bl301 from NAND, src: 0x0001c000, des: 0x01000000, size: 0x00001b90
Wait bl30...Done
Sending bl301.......OK.
Run bl301...
Load bl31 from NAND, src: 0[00020000, des: 0x10100000, size: 0x00012130
Image: gxb_v1.1.3066-b56a895 2016-01-27 20:30:33 xiaobo.gu@droid05]
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: ef be ad de d f0 ad ba efLoad bl33 from NAND, src: 0x00034000, des: 0x01000000, size: 0x0009f040
 be ad de not ES chip
efuse init ops = 13
efuse init hdcp = c, cf9=7
[0.146373 Inits done]
secure task start!
high task start!
low task start!
NOTICE:  BL3-1: v1.0(debug):4c66217
NOTICE:  BL3-1: Built : 17:13:36, Jan 28 2016
INFO:    BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address = 0x1000000
INFO:    BL3-1: Next image spsr = 0x3c9


U-Boot 2015.01-g51fb897-dirty (May 09 2016 - 16:27:43)

DRAM:  1 GiB
Relocation Offset is: 36ed4000
register usb cfg[0][1] = 0000000037f62470
register usb cfg[0][2] = 0000000037f62490
register usb cfg[2][0] = 0000000037f624b0
vpu detect type: 5
vpu clk_level = 7
set vpu clk: 666667000Hz, readback: 666660000Hz(0x300)
vvvv power hold pin set high.....
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=8, system=5.0ns
NAND device id: ad de 14 a7 42 4a ad de
detect NAND device: E revision 1Ynm NAND 8GiB H27UCG8T2E
new oob mode
bus_c=6,bus_t=8,sys=4.0ns,T_REA=16,T_RHOH=15
show_phydev_list
0: nfboot
detect new nand here and new_type:6
get def value at blk:8,page:2048
NAND CKECK:arg nbbt: valid=1, blk=4, page=0
NAND CKECK:arg fbbt: valid=1, blk=5, page=0
outside dtb: 0000000000000000
using dtb on nand
amlnf_dtb_init_partitions: probe.
NAND CKECK:arg ndtb: valid=1, blk=9, page=18
start dts,buffer=0000000033ef2640,dt_addr=0000000033ef2640
parts: 11
00:      logo   0000000002000000 1
01:  recovery   0000000002000000 1
02:       rsv   0000000000800000 1
03:       tee   0000000000800000 1
04:     crypt   0000000002000000 1
05:      misc   0000000002000000 1
06: instaboot   0000000020000000 1
07:      boot   0000000002000000 1
08:    system   0000000050000000 1
09:     cache   0000000020000000 2
10:      data   ffffffffffffffff 4
NAND CKECK:arg ncnf: valid=1, blk=7, page=0
aml_key_init probe.
NAND CKECK:arg nkey: valid=1, blk=6, page=54
boot_device_flag 1
NAND CKECK:arg nenv: valid=1, blk=11, page=12
nfboot    : 0x000000000000-0x000001000000 :partn=0:single_chip single_plane
nfcache   : 0x00000d000000-0x000026000000 :partn=1:single_chip multi_plane
nfcode    : 0x000033000000-0x00008a000000 :partn=9:single_chip multi_plane
nfdata    : 0x0000bd000000-0x000143000000 :partn=1:single_chip multi_plane
(nfboot) bad blks 0
(nfcache) bad blks 0
(nfcode) bad blks 0
(nfdata) bad blks 0
amlnf_logic_init() start
(nfcache), size:26000000
nftl version 1.01.001
nftl start: size 76, free 12
-blks(76), total_blocks(64)
recover_current_block_mapping invalid page data!!
recover_current_block_mapping invalid page data!!
recover_current_block_mapping invalid page data!!
recover_current_block_mapping invalid page data!!
recover_current_block_mapping invalid page data!!
recover_current_block_mapping invalid page data!!
(nfcode), size:8a000000
nftl version 1.01.001
nftl start: size 276, free 29
-blks(276), total_blocks(247)
recover_current_block_mapping invalid page data!!
recover_current_block_mapping invalid page data!!
recover_current_block_mapping invalid page data!!
recover_current_block_mapping invalid page data!!
recover_current_block_mapping invalid page data!!
recover_current_block_mapping invalid page data!!
amlnf_logic_init() done
MMC:   aml_priv->desc_buf = 0x0000000033f22d90
aml_priv->desc_buf = 0x0000000033f24f20
SDIO Port B: 0, SDIO Port C: 1
uboot env amlnf_env_read : ####
In:    serial
Out:   serial
Err:   serial
[store]To run cmd[amlnf dtb_read 0x1000000 0x40000]
cmd dtb_read:
amlnf_dtb_read: ####
262144 bytes dtd_read : OK
Net:   Meson_Ethernet
wipe_data=successful
wipe_cache=successful
upgrade_step=2
reboot_mode=normal
hpd_state=1
[CANVAS]addr=0x3f800000 width=3840, height=2160

[1080p50hz] is invalid for cvbs.
set hdmitx VIC = 31
config HPLL = 2970
HPLL: 0xc800023d
config HPLL done
set_hpll_od3_clk_div[216] div = 6
j = 9  vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 31
enc_vpu_bridge_reset[977]
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L504:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L504:key[deviceid] not programed yet
saradc - saradc sub-system

Usage:
saradc saradc open <channel>            - open a SARADC channel
saradc close    - close the SARADC
saradc getval   - get the value in current channel
saradc get_in_range <min> <max> - return 0 if current value in the range of current channel

Hit any key to stop autoboot:  0
gxb_p201_v1#