Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- NOLO X-Loader (v1.4.14, Jan 8 2010)
- Secondary image size 98440
- Booting secondary
- [ 0.004] Nokia OMAP Loader v1.4.13 (Dec 1 2009) running on Nokia N900 S4.0 GP (RX-51)
- [ 0.010] I2C v3.12
- [ 0.017] System DMA v4.0
- [ 0.023] OneNAND device ID 0040, version ID 0121 (256 MiB, 66 MHz)
- [ 0.029] OneNAND blocks unlocked in 12011 us
- [ 0.029] Flash id: ec4021
- [ 0.038] Partition table successfully read
- [ 0.040] TWL4030 PWR ISR: 01
- [ 0.041] Forcing power key boot reason (R&D flag set)
- [ 0.042] Reset reason: pwr_key
- [ 0.042] McSPI v2.1
- [ 0.045] ERROR: LP5523 not found
- [ 0.046] SMB138C: Not loading driver (version reg. 0x49)
- [ 0.047] BQ24150 (rev. 1) found on I2C bus 1, address 0x6b
- [ 0.049] SSI version 1.0
- [ 0.051] Battery voltage 6.012 V, BSI: 0
- [ 0.051] Disabling charging (R&D flag set)
- [ 0.052] Initializing LCD panel
- [ 0.055] Detecting LCD panel moscow
- [ 0.056] Panel ID: 101234
- [ 0.057] Detected LCD panel: acx565akm
- [ 0.059] DISPC: version 3.0
- [ 0.062] LCD pixel clock 24000 kHz
- [ 0.081] Logo drawn in 28 ms (2089 kB/s)
- [ 0.608] �ber-cool backlight fade-in took 533 ms
- [ 0.609] Initializing USB
- [ 0.614] No USB host detected
- [ 0.615] Loading kernel image info
- Loading kernel (1509 kB)... done in 162 ms (9293 kB/s)
- [ 0.770] Loading initfs image info
- [ 0.772] Total bootup time 831 ms
- [ 0.775] Serial console enabled
- Uncompressing Linux... done, booting the kernel.
- [ 0.000000] Initializing cgroup subsys cpu
- [ 0.000000] Linux version 2.6.35.3-9.5-n900 (abuild@build26) (gcc version 4.5.0 20100414 (MeeGo 4.5.0-1) (GCC) ) #1 PREEMPT Wed Oct 20 23:05:11 UTC 2010
- [ 0.000000] CPU: ARMv7 Processor [412fc083] revision 3 (ARMv7), cr=10c03c7f
- [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
- [ 0.000000] Machine: Nokia RX-51 board
- [ 0.000000] Ignoring unrecognised tag 0x414f4d50
- [ 0.000000] Memory policy: ECC disabled, Data cache writeback
- [ 0.000000] OMAP3430/3530 ES3.1 (iva sgx neon isp )
- [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
- [ 0.000000] Reserving 16404480 bytes SDRAM for VRAM
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
- [ 0.000000] Kernel command line: root=/dev/mmcblk0p1 rootwait console=tty0 console=ttyS2,115200n8 omapfb.vram=0:2M,1:2M,2:2M mtdoops.mtddev=2 nosplash
- [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
- [ 0.000000] allocated 1310720 bytes of page_cgroup
- [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
- [ 0.000000] Memory: 128MB 128MB = 256MB total
- [ 0.000000] Memory: 226996k/226996k available, 35148k reserved, 0K highmem
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
- [ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB)
- [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
- [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
- [ 0.000000] .init : 0xc0008000 - 0xc002b000 ( 140 kB)
- [ 0.000000] .text : 0xc002b000 - 0xc03af000 (3600 kB)
- [ 0.000000] .data : 0xc03cc000 - 0xc040d120 ( 261 kB)
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] RCU lockdep checking is enabled.
- [ 0.000000] RCU-based detection of stalled CPUs is disabled.
- [ 0.000000] Verbose stalled-CPUs detection is disabled.
- [ 0.000000] NR_IRQS:402
- [ 0.000000] Clocking rate (Crystal/Core/MPU): 19.2/332/500 MHz
- [ 0.000000] omap_hwmod: l3_hwmod: cannot be enabled (3)
- [ 0.000000] omap_hwmod: l4_core_hwmod: cannot be enabled (3)
- [ 0.000000] omap_hwmod: l4_per_hwmod: cannot be enabled (3)
- [ 0.000000] omap_hwmod: l4_wkup_hwmod: cannot be enabled (3)
- [ 0.000000] Reprogramming SDRC clock to 332000000 Hz
- [ 0.000000] GPMC revision 5.0
- [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
- [ 0.000000] Total of 96 interrupts on 1 active controller
- [ 0.000000] OMAP GPIO hardware version 2.5
- [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
- [ 0.000000] Console: colour dummy device 80x30
- [ 0.000000] console [tty0] enabled
- [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
- [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
- [ 0.000000] ... MAX_LOCK_DEPTH: 48
- [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
- [ 0.000000] ... CLASSHASH_SIZE: 4096
- [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
- [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
- [ 0.000000] ... CHAINHASH_SIZE: 16384
- [ 0.000000] memory used by lock dependency info: 3695 kB
- [ 0.000000] per task-struct memory footprint: 1152 bytes
- [ 0.000000] Calibrating delay loop... 241.55 BogoMIPS (lpj=942080)
- [ 0.000000] pid_max: default: 32768 minimum: 301
- [ 0.000000] Mount-cache hash table entries: 512
- [ 0.000000] Initializing cgroup subsys cpuacct
- [ 0.000000] Initializing cgroup subsys memory
- [ 0.000000] Initializing cgroup subsys devices
- [ 0.000000] Initializing cgroup subsys freezer
- [ 0.000000] Initializing cgroup subsys blkio
- [ 0.000000] CPU: Testing write buffer coherency: ok
- [ 0.000000] regulator: core version 0.5
- [ 0.000000] NET: Registered protocol family 16
- [ 0.011108] OMAP DMA hardware revision 4.0
- [ 0.621276] bio: create slab <bio-0> at 0
- [ 0.841156] usbcore: registered new interface driver usbfs
- [ 0.860504] usbcore: registered new interface driver hub
- [ 0.873657] usbcore: registered new device driver usb
- [ 0.898620] i2c_omap i2c_omap.1: bus 1 rev3.12 at 2200 kHz
- [ 1.005523] twl4030: PIH (irq 7) chaining IRQs 368..375
- [ 1.007415] twl4030: power (irq 373) chaining IRQs 376..383
- [ 1.030792] twl4030: gpio (irq 368) chaining IRQs 384..401
- [ 1.144500] regulator: VUSB1V5: 1500 mV normal standby
- [ 1.170501] regulator: VUSB1V8: 1800 mV normal standby
- [ 1.193298] regulator: VUSB3V1: 3100 mV normal standby
- [ 1.263702] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
- [ 1.327178] regulator: VIO: 1800 mV normal standby
- [ 1.353668] regulator: VMMC1: 1850 <--> 3150 mV at 1850 mV normal standby
- [ 1.379302] regulator: VDAC: 1800 mV normal standby
- [ 1.407806] regulator: VCSI: 1800 mV normal standby
- [ 1.436431] regulator: V28_A: 2800 <--> 3000 mV at 2600 mV normal standby
- [ 1.466400] regulator: VMMC2_IO_18: 1800 mV normal standby
- [ 1.492950] regulator: V28: 2800 mV normal standby
- [ 1.521118] regulator: VCAM_DIG_18: 1800 mV normal standby
- [ 1.546356] regulator: VCAM_ANA_28: 2800 mV normal standby
- [ 1.554168] i2c_omap i2c_omap.2: bus 2 rev3.12 at 100 kHz
- [ 1.624664] i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz
- [ 1.700927] Advanced Linux Sound Architecture Driver Version 1.0.23.
- [ 1.785491] Switching to clocksource 32k_counter
- [ 2.917816] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
- [ 2.937011] musb_hdrc musb_hdrc: USB Peripheral mode controller at fa0ab000 using DMA, IRQ 92
- [ 2.964355] NET: Registered protocol family 2
- [ 2.980346] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 3.022674] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
- [ 3.024963] TCP bind hash table entries: 8192 (order: 6, 262144 bytes)
- [ 3.047149] TCP: Hash tables configured (established 8192 bind 8192)
- [ 3.048126] TCP reno registered
- [ 3.049713] UDP hash table entries: 128 (order: 1, 10240 bytes)
- [ 3.056915] UDP-Lite hash table entries: 128 (order: 1, 10240 bytes)
- [ 3.077117] NET: Registered protocol family 1
- [ 3.147735] dspbridge_init: 600000 bytes @ 81b00000
- [ 3.445831] msgmni has been set to 443
- [ 3.871826] alg: No test for stdrng (krng)
- [ 3.885559] io scheduler noop registered
- [ 3.898010] io scheduler cfq registered (default)
- [ 4.082153] OMAP DSS rev 2.0
- [ 4.089813] OMAP DISPC rev 3.0
- [ 4.354614] acx565akm spi1.2: omapfb: acx565akm rev 12 LCD detected
- [ 4.510498] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
- [ 4.767211] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a 16550A
- [ 4.844909] serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a 16550A
- [ 4.915252] serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a 16550A
- [ 5.148925] console [ttyS2] enabled
- [ 5.826721] brd: module loaded
- [ 5.937255] OneNAND driver initializing
- [ 5.955291] omap2-onenand omap2-onenand: initializing on CS0, phys base 0x04000000, virtual base d08c0000
- [ 5.957824] Muxed OneNAND 256MB 1.8V 16-bit (0x40)
- [ 5.958435] OneNAND version = 0x0121
- [ 5.966064] Scanning device for bad blocks
- [ 7.554504] Creating 6 MTD partitions on "omap2-onenand":
- [ 7.556365] 0x000000000000-0x000000020000 : "bootloader"
- [ 7.656402] 0x000000020000-0x000000080000 : "config"
- [ 7.734802] 0x000000080000-0x0000000c0000 : "log"
- [ 7.798614] mtdoops: Attached to MTD device 2
- [ 12.142272] 0x0000000c0000-0x0000002c0000 : "kernel"
- [ 12.231414] 0x0000002c0000-0x0000004c0000 : "initfs"
- [ 12.307617] 0x0000004c0000-0x000010000000 : "rootfs"
- [ 12.636657] usbcore: registered new interface driver libusual
- [ 12.666931] input: TWL4030 Keypad as /devices/platform/i2c_omap.1/i2c-1/1-004a/twl4030_keypad/input/input0
- [ 12.723937] TSC2005 driver initializing
- [ 12.755340] input: TSC2005 touchscreen as /devices/virtual/input/input1
- [ 12.809326] i2c /dev entries driver
- [ 12.917510] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
- [ 12.940887] twl4030_wdt twl4030_wdt: Failed to register misc device
- [ 12.944091] twl4030_wdt: probe of twl4030_wdt failed with error -16
- [ 13.167694] No device for DAI tlv320aic3x
- [ 13.213623] No device for DAI omap-mcbsp-dai-0
- [ 13.214416] No device for DAI omap-mcbsp-dai-1
- [ 13.216064] No device for DAI omap-mcbsp-dai-2
- [ 13.218719] No device for DAI omap-mcbsp-dai-3
- [ 13.219360] No device for DAI omap-mcbsp-dai-4
- SD: Unknown CMD52
- [ 13.282867] asoc: tlv320aic3x <-> omap-mcbsp-dai-0 mapping ok
- SD: Unknown CMD52
- [ 13.492401] mmc0: host does not support reading read-only switch. assuming write-enable.
- [ 13.494598] mmc0: new SDHC card at address 4567
- [ 13.533477] mmcblk0: mmc0:4567 QEMU! 1.81 GiB
- [ 13.561737] mmcblk0: p1 p2
- [ 14.004150] input: RX-51 AV Jack as /devices/platform/soc-audio/sound/card0/input2
- SD: Unknown CMD52
- SD: Unknown CMD52
- [ 14.052612] mmc1: host doesn't support card's voltages
- [ 14.124359] mmc1: error -22 whilst initialising SDIO card
- [ 14.204162] ALSA device list:
- [ 14.205291] #0: RX-51 (tlv320aic3x)
- [ 14.213134] TCP cubic registered
- [ 14.214233] Initializing XFRM netlink socket
- [ 14.218536] NET: Registered protocol family 17
- [ 14.224182] NET: Registered protocol family 35
- [ 14.376220] Power Management for TI OMAP3.
- [ 14.953063] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
- [ 15.361572] Console: switching to colour frame buffer device 100x30
- [ 15.689025] regulator_init_complete: incomplete constraints, leaving VCSI on
- [ 15.943634] List of all partitions:
- [ 15.957153] 1f00 128 mtdblock0 (driver?)
- [ 15.992248] 1f01 384 mtdblock1 (driver?)
- [ 16.002807] 1f02 256 mtdblock2 (driver?)
- [ 16.031982] 1f03 2048 mtdblock3 (driver?)
- [ 16.042724] 1f04 2048 mtdblock4 (driver?)
- [ 16.058715] 1f05 257280 mtdblock5 (driver?)
- [ 16.103790] b300 1900544 mmcblk0 driver: mmcblk
- [ 16.142913] b301 1562500 mmcblk0p1
- [ 16.153106] b302 249856 mmcblk0p2
- [ 16.181640] No filesystem could mount root, tried: ext2 ext3 ext4 cramfs
- [ 16.195648] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,1)
- [ 16.226776] [<c003078c>] (unwind_backtrace+0x0/0xe4) from [<c02c7160>] (panic+0x68/0xe8)
- [ 16.240386] [<c02c7160>] (panic+0x68/0xe8) from [<c0008df4>] (mount_block_root+0x238/0x288)
- [ 16.252349] [<c0008df4>] (mount_block_root+0x238/0x288) from [<c00090f0>] (prepare_namespace+0x160/0x1b4)
- [ 16.291351] [<c00090f0>] (prepare_namespace+0x160/0x1b4) from [<c0008a70>] (kernel_init+0x120/0x168)
- [ 16.330932] [<c0008a70>] (kernel_init+0x120/0x168) from [<c002c98c>] (kernel_thread_exit+0x0/0x8)
- [ 16.383819] mtdoops: ready 1, 2 (no erase)
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement