[2018-09-03 22:23:02] [Output] : ★ Jared Lyall reaches for a button from the inside of the car opening up the hood.
[2018-09-03 22:23:12] [Output] :  [English] Rashard Powell says: Yo, let's scan this whip.
[2018-09-03 22:23:14] [Output] : ★ Jared Lyall opens up the hood and holds it inplace.
[2018-09-03 22:23:16] [Output] : Jared Lyall: (( in place* ))
[2018-09-03 22:23:30] [Output] : ★ Rashard Powell reaches toward the door handle opening the door, as he'd kneel down peering around -
[2018-09-03 22:23:44] [Output] : ★ Jared Lyall reaches for a toolbox near him.
[2018-09-03 22:23:57] [Output] : ★ Jared Lyall reaches into the toolbox and takes out a socket and ratchet.
[2018-09-03 22:24:06] [Output] : ★ Jared Lyall untightens the nuts on the battery's negative terminal.
[2018-09-03 22:24:17] [Output] : ★ -checking for any signs of trackers.      ((Rashard Powell))
[2018-09-03 22:24:20] [Output] : ★ Jared Lyall removes the cable entirely.
[2018-09-03 22:24:32] [Output] : ★ Jared Lyall untightens the nut on the battery's positive terminal.
[2018-09-03 22:24:39] [Output] : ★ Jared Lyall then removes the positive cable.
[2018-09-03 22:24:54] [Output] : ★ Jared Lyall reaches for the battery's handle, pulling it upwards, and removing it from the vehicle -
[2018-09-03 22:24:55] [Output] : ★ - entirely.      ((Jared Lyall))
[2018-09-03 22:29:17] [Output] : ★ Jared Lyall lowers the hood, putting his hands under it and looking for the bolts with care -
[2018-09-03 22:29:29] [Output] : ★ - as not to scratch the fenders, he then unscrews the hood those bolts with the -      ((Jared Lyall))
[2018-09-03 22:29:32] [Output] : ★ - socket and ratchet.      ((Jared Lyall))
[2018-09-03 22:30:15] [Output] : ★ Jared Lyall looks around and finds two Tyraps, he cuts them using wire cutters.
[2018-09-03 22:30:34] [Output] : ★ Jared Lyall starts removing clips holding the hood into place.
[2018-09-03 22:31:00] [Output] : ★ Jared Lyall finds a plug near the fender, he prys out the two sides gently to the side.
[2018-09-03 22:31:06] [Output] : ★ Jarad does that using his hand.      ((Jared Lyall))
[2018-09-03 22:31:25] [Output] : ★ Jared Lyall reaches for the hose right under the hood, he pulls it out.
[2018-09-03 22:31:37] [Output] : ★ Jared Lyall ensures the bolts on the sides of the hood holding to the stands are loose, but does not -
[2018-09-03 22:31:44] [Output] : ★ - remove them entirely. He does that using the socket and ratchet.      ((Jared Lyall))
[2018-09-03 22:32:38] [Output] : ★ Jared Lyall takes a little bit of strain off the hood by lifting it up, then pops the left pin out.
[2018-09-03 22:33:08] [Output] : ★ Jared Lyall stands infront of the vehicle, popping the other pin out on the other side with a hammer.
[2018-09-03 22:33:19] [Output] : ADVERT: I need someone to repaint my car, hit me up  | #739182
[2018-09-03 22:33:21] [Output] : ★ Jared Lyall reaches for a pair of pliers, he removes the first pin entirely and places it onto the shelf
[2018-09-03 22:33:22] [Output] : ★ - behind him.      ((Jared Lyall))
[2018-09-03 22:33:44] [Output] : ★ Jared Lyall reaches for the other pin as well, he removes it with the very same pliers.
[2018-09-03 22:33:48] [Output] : ★ Jared Lyall places the second pin next to the first one carefully.
[2018-09-03 22:33:52] [Output] : ★ Jared Lyall lowers down the hood very slowly.
[2018-09-03 22:34:10] [Output] : ★ Jared Lyall reaches for a cushion and places it under the left side of the hood and another one under -
[2018-09-03 22:34:12] [Output] : ★ - the other side.      ((Jared Lyall))
[2018-09-03 22:34:26] [Output] : ★ Jared Lyall reaches past the cushion and starts undoing the bolts entirely now using the socket and -
[2018-09-03 22:34:32] [Output] : ★ - ratchet, the bolts that have been pre-loosened earlier.      ((Jared Lyall))
[2018-09-03 22:34:37] [Output] : ★ Jared Lyall removes two bolts from the left side.
[2018-09-03 22:34:44] [Output] : ★ Jared Lyall reaches for the ride side, and removes the other two bolts.
[2018-09-03 22:34:49] [Output] : ★ Jared Lyall places all the bolts next to the pins on the shelf.
[2018-09-03 22:35:11] [Output] : ★ Jared Lyall slowly reaches for the hood and pulls it up. He firmly grasps it and slowly reaches -
[2018-09-03 22:35:16] [Output] : ★ - towards the wall and leans it up against it.      ((Jared Lyall))
[2018-09-03 22:36:58] [Output] : ★ Jared Lyall reaches for a screwdriver and starts disconnecting screws connecting the intake manifold to
[2018-09-03 22:37:00] [Output] : ★ - the engine.      ((Jared Lyall))
[2018-09-03 22:38:10] [Output] : ★ Jared Lyall reaches for a screwdriver and starts disconnecting screws from a hose connected -
[2018-09-03 22:38:13] [Output] : ★ - to the engine.      ((Jared Lyall))
[2018-09-03 22:42:38] [Output] : ★ Jared Lyall reaches for the low pressure charging point, he removes the cap by turning the cap -
[2018-09-03 22:42:41] [Output] : ★ - counterclockwise.      ((Jared Lyall))
[2018-09-03 22:52:26] [Output] : ★ Jared Lyall reaches for the cowl panel cover and slowly removes it from the front side of the vehicle.
[2018-09-03 22:53:29] [Output] : ★ Jared Lyall presses on a button, lifting the lift.
[2018-09-03 22:53:32] [Output] : Jared Lyall: (( >lifting the lift ))
[2018-09-03 22:54:13] [Output] : ★ Jared Lyall reaches for the socket and ratchet, he looks up at the vehicle near the front at the -
[2018-09-03 22:54:16] [Output] : ★ - control arm.      ((Jared Lyall))
[2018-09-03 22:55:25] [Output] : ★ Jared Lyall reaches for the 18mm ratchet, he starts loosening the bolts on the tuning fork, he does not
[2018-09-03 22:55:27] [Output] : ★ - remove them.      ((Jared Lyall))
[2018-09-03 22:55:47] [Output] : ★ Jared Lyall loosens the bolt at the top of the ball joint.
[2018-09-03 22:56:30] [Output] : ★ Jared Lyall loosens up another bolt near the tuning fork.
[2018-09-03 22:57:28] [Output] : ★ Jared Lyall reaches for the bolt on the tuning fork, he starts unscrewing it with his hands, and pulls 0
[2018-09-03 22:57:31] [Output] : ★ - the bolt through carefully.      ((Jared Lyall))
[2018-09-03 22:57:47] [Output] : ★ Jared Lyall slowly slides the tuning fork out of its pathway entirely.
[2018-09-03 22:58:00] [Output] : ★ Jared Lyall reaches for some PT Blaster on the balljoint shaft as to coax it out.
[2018-09-03 22:58:33] [Output] : ★ Jared Lyall heads towards the lower link. He grabs the 10mm ratchet and starts unbolting two -
[2018-09-03 22:58:34] [Output] : ★ - bolts.      ((Jared Lyall))
[2018-09-03 22:58:45] [Output] : ★ Jared Lyall reaches for a hammer carefully.
[2018-09-03 22:59:39] [Output] : ★ Jared Lyall puts the nut back on the bolt on the ball joint, he puts an extension onto the nut.
[2018-09-03 23:00:02] [Output] : ★ Jared Lyall slowly taps on the extension with the hammer. He bangs carefully onto the extension as -
[2018-09-03 23:00:05] [Output] : ★ - to forse it down.      ((Jared Lyall))
[2018-09-03 23:00:39] [Output] : ★ The ball joint should come loose.      ((Jared Lyall))
[2018-09-03 23:00:51] [Output] : ★ Jared Lyall keeps the nut on the bolt as for ball joint not to hit the disc.
[2018-09-03 23:01:09] [Output] : ★ Jared Lyall unpins the bolt on the top using his hand since it has been pre-loosened.
[2018-09-03 23:01:42] [Output] : ★ Jared Lyall slowly pulls out the ball joint, its already against the base of the nut so it shouldn't -
[2018-09-03 23:01:45] [Output] : ★ - be dangerous to the disc.      ((Jared Lyall))
[2018-09-03 23:01:59] [Output] : ★ Jared Lyall holds the ball joint in place then removes the nut slowly.
[2018-09-03 23:02:07] [Output] : ★ Jared Lyall wiggles the ball joint back and forth a bit and removes it entirely.
[2018-09-03 23:03:00] [Output] : ★ With that, the control arm has been removed.      ((Jared Lyall))
[2018-09-03 23:03:09] [Output] : ★ Jared Lyall places the control arm onto the shelf.
[2018-09-03 23:04:17] [Output] : ★ Jared Lyall removes the lid seal at the back the cowl.
[2018-09-03 23:04:30] [Output] : ★ Jared Lyall removes the front wiper arms from the bottom, unscrewing them from their -
[2018-09-03 23:04:33] [Output] : ★ - location.      ((Jared Lyall))
[2018-09-03 23:04:53] [Output] : ★ Jared Lyall removes the right section of the cowl panel cover by opening the fixing clips, and turning -
[2018-09-03 23:05:01] [Output] : ★ - them ninety degrees.      ((Jared Lyall))
[2018-09-03 23:05:26] [Output] : ★ Jared Lyall lifts up the section of cover at the front edge and removes it by unbolting two -
[2018-09-03 23:05:38] [Output] : ★ bolts and them pulls it backwards carefully.      ((Jared Lyall))
[2018-09-03 23:06:00] [Output] : ★ Jared Lyall opens the fixing clips for the cowl panel cover by turning them 90 degrees clockwise.
[2018-09-03 23:06:07] [Output] : ★ Jared Lyall unclips the cowl panel cover.
[2018-09-03 23:06:35] [Output] : ★ Jared Lyall does so by grabbing a plastic wedge and removes it from the rear edge.
[2018-09-03 23:06:42] [Output] : ★ The cowl panel cover would be removed.      ((Jared Lyall))
[2018-09-03 23:07:36] [Output] : ★ Jared Lyall pulls the ends of the front profile seal by backing off the retaining lugs.
[2018-09-03 23:07:48] [Output] : ★ Jared Lyall carefully pulls the front profile seal off the retaining flange.
[2018-09-03 23:08:20] [Output] : ★ Jared Lyall removes the front profile seal by pulling it towards the engine.
[2018-09-03 23:08:32] [Output] : ★ Jared Lyall lifts up the foam corner pieces at the ends of the profile seal.
[2018-09-03 23:08:47] [Output] : ★ Jared Lyall pulls the ends of the rear profile seal, by lifting it upwards.
[2018-09-03 23:08:54] [Output] : ★ The rear profile seal comes off.      ((Jared Lyall))
[2018-09-03 23:10:02] [Output] : ★ Jared Lyall raises up the vehicle using the lift.
[2018-09-03 23:10:18] [Output] : ★ Jared Lyall reaches for the appropriate ratchet after inspecting the various nuts on the engine -
[2018-09-03 23:10:21] [Output] : ★ - underbody panelling.      ((Jared Lyall))
[2018-09-03 23:10:36] [Output] : ★ Jared Lyall starts unscrewing them, then removes the engine underbody panelling.
[2018-09-03 23:11:56] [Output] : ★ Jared Lyall removes the side cover seal to the right.
[2018-09-03 23:12:17] [Output] : ★ Jared Lyall removes the centre cover - the centre pleneum panel wall - at the bottom by lifting it -
[2018-09-03 23:12:19] [Output] : ★ - downwards.      ((Jared Lyall))
[2018-09-03 23:12:45] [Output] : ★ Jared Lyall removes the seal on the centre plenum panel at the bottom on the removed -
[2018-09-03 23:13:16] [Output] : ★ - cover bottom, then pulls it out. He puts the seal back on afterwards.      ((Jared Lyall))
[2018-09-03 23:15:53] [Output] : ★ Jared Lyall unscrews the fastening screws on the underbody cover.
[2018-09-03 23:16:12] [Output] : ★ Jared Lyall removes the fastening nuts on the underbody cover.
[2018-09-03 23:16:21] [Output] : ★ Jared Lyall pulls the front underbody cover.
[2018-09-03 23:16:28] [Output] : ★ Jared Lyall does so by removing it from the overlap
[2018-09-03 23:17:07] [Output] : ★ Jared Lyall unscrews the fastening screws on the right side underbody.
[2018-09-03 23:17:16] [Output] : ★ Jared Lyall removes the fastening nuts and pulls it off out of the overlaps as well.
[2018-09-03 23:17:21] [Output] : ★ Jared Lyall does the same process for the other side underbody.
[2018-09-03 23:21:26] [Output] : ★ Jared Lyall unscrews fastening nuts from the front wheel housing liner.
[2018-09-03 23:21:35] [Output] : ★ Jared Lyall removes the fastening screws from the front wheel housing liner.
[2018-09-03 23:22:23] [Output] : ★ Jared Lyall reaches for a bolt and ratchet and starts removing the nuts on the wheel.
[2018-09-03 23:22:40] [Output] : ★ Jared Lyall pulls the wheel out, rolls it towards the wall and grabs the wheel housing liner -
[2018-09-03 23:22:42] [Output] : ★ - placing it onto the shelf.      ((Jared Lyall))
[2018-09-03 23:23:20] [Output] : ★ Jared Lyall lowers the vehicle once more.
[2018-09-03 23:23:28] [Output] : ★ Jared Lyall removes the wire harness from the plenum panel.
[2018-09-03 23:23:28] [Output] : * Rashard Powell puts the key in the door to lock it. *
[2018-09-03 23:23:34] [Output] : ★ Jared Lyall releases the fuse box.
[2018-09-03 23:23:48] [Output] : ★ Jared Lyall lifts up the relay fuse box in the plenum panel at both sides.
[2018-09-03 23:24:02] [Output] : ★ Jared Lyall lifts it up and disconnects the wire harness for the DME control unit in the plenum panel.
[2018-09-03 23:24:08] [Output] : ★ Javeon Brooks unties the knot on the BMW's rear bumper hook, then the vans.
[2018-09-03 23:24:17] [Output] : ★ Javeon Brooks gathers the rope, looping it.
[2018-09-03 23:24:19] [Output] : ★ Jared Lyall releases the connector on the DME control unit and disconnects it by pulling it to the -
[2018-09-03 23:24:19] [Output] : ★ Rashard Powell places both hands on the back of the vehicle, using all force to push it forwards.
[2018-09-03 23:24:20] [Output] : ★ - side.      ((Jared Lyall))
[2018-09-03 23:24:55] [Output] : ★ Jared Lyall removes the sealing sleeve with wire harness from the on-board panel.
[2018-09-03 23:25:20] [Output] : ★ Jared Lyall places the engine wire harness onto the engine block.
[2018-09-03 23:25:34] [Output] : ★ Jared Lyall disconnects the fuel low-pressure line.
[2018-09-03 23:25:53] [Output] : ★ Jared Lyall releases and disconnects the tank ventilation and vacuum line at the connection point.
[2018-09-03 23:26:01] [Output] : ★ Jared Lyall reaches for a piece of cloth, looking at his position for a few seconds.
[2018-09-03 23:26:16] [Output] : ★ Jared Lyall places the cloth under the connection for the fuel low-pressure line to be disconnected -
[2018-09-03 23:26:23] [Output] : ★ - in order to collect the emerging fluid.      ((Jared Lyall))
[2018-09-03 23:26:39] [Output] : ★ Jared Lyall releases the fuel low-pressure line by countering with a wrench and disconnects it.
[2018-09-03 23:26:49] [Output] : ★ Jared Lyall counters at the centre piece and removes the union nut on the engine side.
[2018-09-03 23:27:58] [Output] : ★ Jared Lyall removes the two screws and nuts on the body and valve cover.
[2018-09-03 23:28:41] [Output] : ★ Jared Lyall removes the M10 aluminum screw.
[2018-09-03 23:28:44] [Output] : ★ Jared Lyall counters the M10 nut.
[2018-09-03 23:28:50] [Output] : ★ Jared Lyall removes the bracket on the valve cover.
[2018-09-03 23:28:54] [Output] : ★ Jared Lyall removes the bracket on the body.
[2018-09-03 23:29:08] [Output] : ★ Jared Lyall removes the torque support.
[2018-09-03 23:29:17] [Output] : ★ Jared Lyall removes the two screws on the engine bracket and on the supporting frame.
[2018-09-03 23:29:28] [Output] : ★ Jared Lyall removes the lower torque support.
[2018-09-03 23:29:42] [Output] : ★ Jared Lyall disconnects the plug connections for oxygen sensors at the left and right.
[2018-09-03 23:29:53] [Output] : ★ Jared Lyall releases and disconnects the oxygen sensor plug connection at both sides.
[2018-09-03 23:30:26] [Output] : ★ Jared Lyall removes the secondary-air pump by unscrewing the secondary-air pump and pulling -
[2018-09-03 23:30:28] [Output] : ★ - off the hose.      ((Jared Lyall))
[2018-09-03 23:30:48] [Output] : ★ Jared Lyall places the secondary-air pump on the engine and secures it with a tie-wrap to -
[2018-09-03 23:30:51] [Output] : ★ - keep it from falling down.      ((Jared Lyall))
[2018-09-03 23:31:08] [Output] : ★ Jared Lyall pulls the vacuum line off of the vacuum pump at the connection piece.
[2018-09-03 23:31:22] [Output] : ★ Jared Lyall releases the clips on the coolant hoses at the plenum panel and removes them -
[2018-09-03 23:31:30] [Output] : ★ - from the connection point at the plenum panel.      ((Jared Lyall))
[2018-09-03 23:31:35] [Output] : ★ Jared Lyall removes the coolant hoses.
[2018-09-03 23:32:03] [Output] : ★ Jared Lyall disconnects the hose for coolant reservoir underneath the valve cover.
[2018-09-03 23:33:04] [Output] : ★ Jared Lyall removes the trim panel on the left of the fluid reservoir.
[2018-09-03 23:33:21] [Output] : ★ Jared Lyall reaches for a syringe.
[2018-09-03 23:33:45] [Output] : ★ Jared Lyall removes Pentosin from the reservoir using the syringe until the reservoir is virtually -
[2018-09-03 23:33:46] [Output] : ★ - empty.      ((Jared Lyall))
[2018-09-03 23:34:10] [Output] : ★ Jared Lyall reaches for a piece of cloth under the PDCC reservoir to keep emerging Pentosin -
[2018-09-03 23:34:18] [Output] : ★ - from getting onto the water lines.      ((Jared Lyall))
[2018-09-03 23:34:33] [Output] : ★ Jared Lyall loosens the hose clamps and pull the reservoir off the lines.
[2018-09-03 23:35:08] [Output] : ★ Jared Lyall releases and disconnects the hose for the hydraulic oil tank.
[2018-09-03 23:35:22] [Output] : ★ Jared Lyall removes the air box on the throttle valve by removing the design cover.
[2018-09-03 23:35:31] [Output] : ★ Jared Lyall unscrews the bayonet bolt at the air box.
[2018-09-03 23:35:50] [Output] : ★ Jared Lyall releases and unplugs the connector for the boost pressure sensor.
[2018-09-03 23:35:59] [Output] : ★ Jared Lyall releases hose clamps on the air box at both sides.
[2018-09-03 23:36:13] [Output] : ★ Jared Lyall pulls the air box out of the retaining clip, and leaves the ventilation line.
[2018-09-03 23:36:24] [Output] : ★ The ventilation line for the crankcase is still fitted.      ((Jared Lyall))
[2018-09-03 23:36:32] [Output] : ★ Jared Lyall sets the airbox down onto the engine.
[2018-09-03 23:36:44] [Output] : ★ Jared Lyall disconnects the wastegate control lines on both sides at the T-piece.
[2018-09-03 23:36:56] [Output] : ★ Jared Lyall releases and disconnects the clamps on the coolant lines on the aluminum pipes for hte -
[2018-09-03 23:36:57] [Output] : Jared Lyall: (( the* ))
[2018-09-03 23:37:03] [Output] : ★ - thermostat housing at both sides.      ((Jared Lyall))
[2018-09-03 23:37:17] [Output] : ★ Jared Lyall secures the coolant hoses together with the pressure hoses for the charge air -
[2018-09-03 23:37:24] [Output] : ★ - cooler at the lock carrier via the tie-wraps.      ((Jared Lyall))
[2018-09-03 23:37:41] [Output] : ★ Jared Lyall fits the safety hooks for the upper control arm at both sides to relieve the control arms.
[2018-09-03 23:37:46] [Output] : ★ Jared Lyall raises the vehicle halfway.
[2018-09-03 23:38:01] [Output] : ★ Jared Lyall releases and disconnects the plug connection for the RPM sensor at the wheel -
[2018-09-03 23:38:04] [Output] : ★ - carrier on both sides.      ((Jared Lyall))
[2018-09-03 23:38:13] [Output] : ★ Jared Lyall removes the fastening nuts on the chassis.
[2018-09-03 23:38:29] [Output] : ★ The fastening nuts are on the upper control arms at both sides.      ((Jared Lyall))
[2018-09-03 23:38:44] [Output] : ★ Jared Lyall removes the fastening nuts on the connecting link at the spring strut on both sides.
[2018-09-03 23:38:58] [Output] : ★ Jared Lyall loosens the fastening nuts on the lower control arms at both sides, but does not remove them
[2018-09-03 23:39:14] [Output] : ★ Jared Lyall removes the fastening nut on the power-steering pressure line holder and detaches the -
[2018-09-03 23:39:23] [Output] : ★ - retaining eyelet by fastening the nut on the holder.      ((Jared Lyall))
[2018-09-03 23:39:31] [Output] :  [English] Rashard Powell says: Look at this nigga go.
[2018-09-03 23:39:37] [Output] :  [English] Rashard Powell says: Fucking monster, he is!
[2018-09-03 23:39:46] [Output] : ★ Jared Lyall disconnects the steel flexi-pipes on the PDCC valve block at the front.
[2018-09-03 23:39:59] [Output] : ★ Jared Lyall unscrews the cap screws on the steel flexi-pipes.
[2018-09-03 23:40:18] [Output] : ★ Jared Lyall removes the fastening screw on the ground cable for the engine at the right -
[2018-09-03 23:40:21] [Output] : ★ front frame carrier.      ((Jared Lyall))
[2018-09-03 23:40:26] [Output] : ★ Jared Lyall raises the vehicle fully.
[2018-09-03 23:40:40] [Output] : ★ Jared Lyall carefully releases the tension lock, then disconnects the pressure hose on the -
[2018-09-03 23:40:44] [Output] : ★ - charge air cooler at both sides.      ((Jared Lyall))
[2018-09-03 23:40:57] [Output] : ★ Jared Lyall leaves the hose hanging freely.
[2018-09-03 23:41:14] [Output] : ★ Jared Lyall presses the pressure hose aside at both sides, disconnecting the hose clamp fitted -
[2018-09-03 23:41:23] [Output] : ★ - behind it on the suction hose and pulls off the hose.      ((Jared Lyall))
[2018-09-03 23:41:37] [Output] : ★ Jared Lyall disconnects the ambient air valve at the suction hose on both sides.
[2018-09-03 23:41:47] [Output] : ★ Jared Lyall disconnects the ambient air valve at the pressure hose on both sides.
[2018-09-03 23:42:00] [Output] : ★ Jared Lyall disconnects the vacuum line on the ambient air valve on both sides and removes -
[2018-09-03 23:42:01] [Output] : ★ - the valve.      ((Jared Lyall))
[2018-09-03 23:42:20] [Output] : ★ Jared Lyall loosens steel flexi-pipe to the expansion hose.
[2018-09-03 23:42:39] [Output] : ★ Jared Lyall disconnects the steel flexi-pipe.
[2018-09-03 23:42:50] [Output] : ★ Jared Lyall removes the return hose for the hydraulic oil cooler.
[2018-09-03 23:42:58] [Output] : ★ Jared Lyall unscrews the fastening screw between the hose clamps.
[2018-09-03 23:43:06] [Output] : ★ Jared Lyall disconnects the return hose at the hydraulic oil cooler.
[2018-09-03 23:43:27] [Output] : ★ Jared Lyall removes the intake pipe and pressure line from the air conditioning compressor.
[2018-09-03 23:43:36] [Output] : ★ Jared Lyall loosens the fastening screw on the air conditioning line.
[2018-09-03 23:43:48] [Output] : ★ Jared Lyall removes the air-conditioning line holder from the guide.
[2018-09-03 23:43:55] [Output] : ★ Jared Lyall removes the PDK wiring harness.
[2018-09-03 23:44:08] [Output] : ★ Jared Lyall removes fastening screws on the heat protection panel for the PDK wiring harness on the -
[2018-09-03 23:44:11] [Output] : ★ - transmission.      ((Jared Lyall))
[2018-09-03 23:44:23] [Output] : ★ Jared Lyall removes the heat protection panel for the PDK wiring harness.
[2018-09-03 23:44:36] [Output] : ★ Jared Lyall releases and unplugs the connectors on the end of the PDK wiring harness at the -
[2018-09-03 23:44:41] [Output] : ★ - transmission and loosens the retaining clip.      ((Jared Lyall))
[2018-09-03 23:44:58] [Output] : ★ Jared Lyall loosens the retaining clip on the PDK wiring harness and removes the PDK wiring -
[2018-09-03 23:45:00] [Output] : ★ - harness from the clips.      ((Jared Lyall))
[2018-09-03 23:45:20] [Output] : ★ Jared Lyall disconnects the parking lock cable from the ball joint on the transmission.
[2018-09-03 23:45:30] [Output] : ★ Jared Lyall lifts the parking lock cable out of the support and secures it towards the top.
[2018-09-03 23:45:40] [Output] : ★ Jared Lyall removes the heat protection panel between the universal joint for the steering gear -
[2018-09-03 23:45:47] [Output] : ★ - and the primary catalytic converter.      ((Jared Lyall))
[2018-09-03 23:45:55] [Output] : ★ Jared Lyall removes the fastening screws on the heat protection panel then removes it.
[2018-09-03 23:46:13] [Output] : ★ Jared Lyall pulls off the universal power joint connecter.
[2018-09-03 23:46:24] [Output] : ★ Jared Lyall loosens the clamping screw and slides the universal joint and lower part of steering -
[2018-09-03 23:46:31] [Output] : ★ column upwards.      ((Jared Lyall))
[2018-09-03 23:47:03] [Output] : ★ Jared Lyall loosens supply and return hose for the ATF transmission fluid cooler and drains the -
[2018-09-03 23:47:04] [Output] : ★ - fluid.      ((Jared Lyall))
[2018-09-03 23:47:30] [Output] : ★ Jared Lyall places all the assembly drivers to the correct sequential positions.
[2018-09-03 23:48:19] [Output] : ★ The assembly drivers being that of a Master Gear unit elevating platform.      ((Jared Lyall))
[2018-09-03 23:48:55] [Output] : ★ Jared Lyall places the transmission bracket onto the transmission mount.
[2018-09-03 23:49:20] [Output] : ★ Jared Lyall mounts the assembly driver on the cross panel.
[2018-09-03 23:49:32] [Output] : ★ Jared Lyall secures the axles using the wheel hub holder.
[2018-09-03 23:50:11] [Output] : ★ Jared Lyall uses the fourth bracket in conjunction with the wheel hub holder, protecting the axles.
[2018-09-03 23:50:24] [Output] : ★ Jared Lyall places the assembly driver bracket onto the front-axle carrier.
[2018-09-03 23:50:39] [Output] : ★ Jared Lyall places the front-axle carrier support bracket onto the rear of the front-axle carrier.
[2018-09-03 23:51:01] [Output] : ★ Jared Lyall gets the elevating platform ready.
[2018-09-03 23:51:14] [Output] : ★ Jared Lyall moves the elevating platform to the jacking points on the front axle.
[2018-09-03 23:51:29] [Output] : ★ Jared Lyall sets the height of the drivers and makes sure they are supported.
[2018-09-03 23:51:33] [Output] : ★ Jared Lyall removes the bolts on the lower arms.
[2018-09-03 23:51:44] [Output] : ★ Jared Lyall raises the elevating platform slightly.
[2018-09-03 23:51:51] [Output] : ★ This relieves the pressure on the bolts on the lower control arms.      ((Jared Lyall))
[2018-09-03 23:52:01] [Output] : ★ Jared Lyall pulls out the bolts on the lower control arm on both sides.
[2018-09-03 23:52:10] [Output] : ★ Jared Lyall removes the safety hooks for the upper control arms.
[2018-09-03 23:52:17] [Output] : ★ Jared Lyall detaches the front-axle carrier.
[2018-09-03 23:52:36] [Output] : ★ Jared Lyall removes the fastening screws on the front-axle carrier to the longtitudinal members.
[2018-09-03 23:52:51] [Output] : ★ Jared Lyall removes the fastening screws securing the anti-roll bar mount to the supporting plates.
[2018-09-03 23:53:09] [Output] : ★ Jared Lyall presses the rear wheel housing cover down and removes the traverse strut -
[2018-09-03 23:53:16] [Output] : ★ - between the supporting plate and door sill.      ((Jared Lyall))
[2018-09-03 23:53:28] [Output] : ★ Jared Lyall removes the transverse strut between the supporting plate and door sill.
[2018-09-03 23:53:40] [Output] : ★ Jared Lyall fits the wheel hub holder at both sides using the assembly pins on the wheel hub.
[2018-09-03 23:53:53] [Output] : ★ Jared Lyall removes the fastening screws on the rear transmission mount.
[2018-09-03 23:54:10] [Output] : ★ Jared Lyall slowly lowers the elevating platform.
[2018-09-03 23:54:25] [Output] : ★ Jared Lyall guides the air-conditioning lines along.
[2018-09-03 23:54:38] [Output] : ★ Jared Lyall moves the engine out from under the vehicle using the elevating platform eventually.
[2018-09-03 23:54:46] [Output] : ★ Jared Lyall disconnects the transmission and removes it as well.
[2018-09-03 23:55:01] [Output] : ★ Jared Lyall removes the wheels of the Porsche as well (just as he removed the first one).