; Configuration file for Duet Maestro (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.5 on Thu Jan 09 2020 20:00:48 GMT+0100 (Mitteleuropäische Normalzeit)

; General preferences
G90                                     ; send absolute coordinates...
M83                                     ; ...but relative extruder moves
M550 P"Ender 3 Pro"                     ; set printer name
M918 P1 E4 F2000000                     ; configure direct-connect display

; Network
M552 P0.0.0.0 S1                        ; enable network and acquire dynamic address via DHCP
M586 P0 S1                              ; enable HTTP
M586 P1 S0                              ; disable FTP
M586 P2 S0                              ; disable Telnet

; Drives
M569 P0 S0                              ; physical drive 0 goes backwards
M569 P1 S0                              ; physical drive 1 goes backwards
M569 P2 S1                              ; physical drive 2 goes forwards
M569 P3 S0                              ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3                        ; set drive mapping
M350 X32 Y32 Z32 E32 I1                 ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z800.00 E815.00     ; set steps per mm
M566 X1200.00 Y1200.00 Z24.00 E300.00   ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z180.00 E6000.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E5000.00   ; set accelerations (mm/s^2)
M906 X700 Y600 Z600 E500 I50            ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                        ; set axis minima
M208 X235 Y235 Z260 S0                  ; set axis maxima

; Endstops
M574 X1 Y1 Z1 S1                        ; set active high endstops

; Z-Probe
M558 P9 H5 F120 T6000                   ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X0 Y0 Z2.5                     ; set Z probe trigger value, offset and trigger height
M557 X15:215 Y15:195 S20                ; define mesh grid

; Heaters
M307 H0 B0 S1.00                        ; disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4092 R2200             ; set thermistor + ADC parameters for heater 0
M143 H0 S150                            ; set temperature limit for heater 0 to 150C
M305 P1 T100000 B4092 R2200             ; set thermistor + ADC parameters for heater 1
M143 H1 S275                            ; set temperature limit for heater 1 to 275C

; Fans
M106 P0 S0 I0 F500 H-1                  ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45               ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1:0 T45             ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                        ; define tool 0
G10 P0 X0 Y0 Z0                         ; set tool 0 axis offsets
G10 P0 R0 S0                            ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined