DDR 9fffbe1e78 cym 24/02/04-10:09:20,fwver: v1.16
LPDDR5, 2400MHz
channel[0] BW=16 Col=10 Bk=16 CS0 Row=16 CS=1 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=16 CS0 Row=16 CS=1 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=16 CS0 Row=16 CS=1 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=16 CS0 Row=16 CS=1 Die BW=16 Size=2048MB
Manufacturer ID:0xff
CH0 RX Vref:26.3%, TX Vref:19.0%,0.0%
CH1 RX Vref:28.3%, TX Vref:21.0%,0.0%
CH2 RX Vref:27.1%, TX Vref:18.0%,0.0%
CH3 RX Vref:25.8%, TX Vref:18.0%,0.0%
change to F1: 534MHz
change to F2: 1320MHz
change to F3: 1968MHz
change to F0: 2400MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-orangepi (Aug 22 2024 - 17:22:05)
Trying to boot from MMC1
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(7612223b82...) + OK
## Checking uboot 0x00200000 ... sha256(c16ace5afe...) + OK
## Checking fdt 0x0031fd00 ... sha256(3b5978c23d...) + OK
## Checking atf-2 0xff100000 ... sha256(70505bb764...) + OK
## Checking atf-3 0x000f0000 ... sha256(b2af21b504...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 743.241 ms

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-868-g040d2de11:derrick.huang, fwver: v1.48
NOTICE:  BL31: Built : 15:02:44, Dec 19 2024
INFO:    spec: 0x1
INFO:    code: 0x88
INFO:    ext 32k is not valid
INFO:    ddr: stride-en 4CH
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0
INFO:    l3 cache partition cfg-0
INFO:    system boots from cpu-hwid-0
INFO:    disable memory repair
INFO:    idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO:    dfs DDR fsp_params[0].freq_mhz= 2400MHz
INFO:    dfs DDR fsp_params[1].freq_mhz= 534MHz
INFO:    dfs DDR fsp_params[2].freq_mhz= 1320MHz
INFO:    dfs DDR fsp_params[3].freq_mhz= 1968MHz
INFO:    BL31: Initialising Exception Handling Framework
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2017.09-armbian-2017.09-S47bf-P0ef3-H3d34-V2db7-Bb703-R448a (Apr 22 2025 - 17:22:24 -0500)

Model: RK3588 Orange Pi 5 Ultra
MPIDR: 0x0
PreSerial: 2, raw, 0xfeb50000
DRAM:  8 GiB
Sysmem: init
Relocation Offset: eda3f000
Relocation fdt: eb9f89e0 - eb9fece0
CR: M/C/I
Using default environment

DM: v2
mmc@fe2c0000: 1, mmc@fe2e0000: 0
Card did not respond to voltage select!
mmc_init: -95, time 14
switch to partitions #0, OK
mmc1 is current device
Boot from SDcard
Bootdev(scan): mmc 1
MMC1: Legacy, 52Mhz
PartType: EFI
No misc partition
boot mode: None
FIT: No boot partition
Failed to load DTB, ret=-2
No valid DTB, ret=-22
Failed to get kernel dtb, ret=-22
Model: RK3588 Orange Pi 5 Ultra
## Error: Can't overwrite "ethaddr"
## Error inserting "ethaddr" variable, errno=1
## Error: Can't overwrite "eth1addr"
## Error inserting "eth1addr" variable, errno=1
CLK: (sync kernel. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
  b0pll 24000 KHz
  b1pll 24000 KHz
  lpll 24000 KHz
  v0pll 24000 KHz
  aupll 24000 KHz
  cpll 1500000 KHz
  gpll 1188000 KHz
  npll 24000 KHz
  ppll 1100000 KHz
  aclk_center_root 702000 KHz
  pclk_center_root 100000 KHz
  hclk_center_root 396000 KHz
  aclk_center_low_root 500000 KHz
  aclk_top_root 750000 KHz
  pclk_top_root 100000 KHz
  aclk_low_top_root 396000 KHz
No misc partition
Net:   No ethernet found.
Hit key to stop autoboot('CTRL+C'):  0
starting USB...
Bus usb@fc800000: failed to get usb phy
Port not available.
Bus usb@fc840000: failed to get usb phy
Port not available.
Bus usb@fc880000: failed to get usb phy
Port not available.
Bus usb@fc8c0000: failed to get usb phy
Port not available.
USB is stopped. Please issue 'usb start' first.
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found U-Boot script /boot/boot.scr
4149 bytes read in 26 ms (155.3 KiB/s)
## Executing script at 00500000
Boot script loaded from mmc 1:1
200 bytes read in 24 ms (7.8 KiB/s)
17023944 bytes read in 1407 ms (11.5 MiB/s)
48073216 bytes read in 3902 ms (11.7 MiB/s)
** File not found /boot/dtb/rockchip/rk3588-orangepi-5-ultra.dtb **
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
No FDT memory address configured. Default at 0xeb9f89e0
Trying kaslrseed command... Info: Unknown command can be safely ignored since kaslrseed does not apply to all boards.
Unknown command 'kaslrseed' - try 'help'
Fdt Ramdisk skip relocation
No misc partition
## Loading init Ramdisk from Legacy Image at 0a200000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    17023880 Bytes = 16.2 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
ERROR: Did not find a cmdline Flattened Device Tree
Could not find a valid device tree
SCRIPT FAILED: continuing...

Device 0: unknown device

Device 1: unknown device
Card did not respond to voltage select!
mmc_init: -95, time 13

Device 2: Could not get clock for spi@fe2b0000: -2
unknown device

Device 1: Could not get clock for spi@fe2b0000: -2
unknown device

Device 0: unknown device
starting USB...
Bus usb@fc800000: "Synchronous Abort" handler, esr 0x96000004

* Reason:        Exception from a Data abort, from current exception level
* PC         =   000000000028b170
* LR         =   000000000028b170
* SP         =   00000000eb9f7aa0
* ESR_EL2    =   0000000096000004
* Reloc Off  =   00000000eda3f000

x0 : ffffffffffffffff x1 : 00000000edd10461
x2 : 00000000fffffffc x3 : 0000000000000000
x4 : 00000000edd0fe2b x5 : 000000000000006e
x6 : 00000000edd0ee95 x7 : 0000000000000000
x8 : 0000000000000044 x9 : 0000000000000008
x10: fffffffffffffff0 x11: 0000000000000000
x12: 00000000ebc47b48 x13: 0000000000000002
x14: 0000000000000004 x15: 0000000000000002
x16: 00000000edca567c x17: 0000000000000084
x18: 00000000eb9ffce8 x19: 00000000ebc4f2d0
x20: 00000000ebc4f140 x21: 0000000000000000
x22: 00000000ebc3ee30 x23: 00000000edd2792e
x24: 00000000edd5fc48 x25: 0000000000000000
x26: 0000000000000000 x27: 0000000000000000
x28: 00000000ebc4bd80 x29: 00000000eb9f7c80


Call trace:
  PC:   [< 0028b170 >]
  LR:   [< 0028b170 >]

Stack:
        [< 0028b170 >]
        [< 0023480c >]
        [< 00287340 >]
        [< 00213f58 >]
        [< 00213ff8 >]
        [< 0022ca7c >]
        [< 00219330 >]
        [< 002194bc >]
        [< 00218be4 >]
        [< 0022c010 >]
        [< 0022ca7c >]
        [< 00219330 >]
        [< 002194bc >]
        [< 00218be4 >]
        [< 0022c010 >]
        [< 0022ca7c >]
        [< 00219330 >]
        [< 002194bc >]
        [< 00218c20 >]
        [< 00219104 >]
        [< 00218fe0 >]
        [< 002194bc >]
        [< 00218be4 >]
        [< 0022c010 >]
        [< 0022ca7c >]
        [< 00219330 >]
        [< 002194bc >]
        [< 00218be4 >]
        [< 0022bf70 >]
        [< 00219b74 >]
        [< 00217634 >]
        [< 0021a20c >]
        [< 002974b4 >]
        [< 0021a440 >]
        [< 00201dc8 >]

Copy info from "Call trace..." to a file(eg. dump.txt), and run
command in your U-Boot project: ./scripts/stacktrace.sh dump.txt

Resetting CPU ...

### ERROR ### Please RESET the board ###