Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- beign to init dram
- DRAM DRIVE INFO: V1.1
- DRAM Type =7 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
- DRAM normal_mode value: 00000001
- DRAM CLK =732 MHZ
- rsb_send_initseq: rsb clk 400Khz -> 3Mhz
- PMU: AXP81X
- ddr voltage = 1200 mv
- using ic A83T
- using axp AXP813
- DRAM zq value: 00003bfb
- init dram ok
- [ 3.930]
- U-Boot 2011.09-rc1-dirty (Nov 05 2015 - 23:11:51) Allwinner Technology
- [ 3.938]version: 2.1.0
- normal mode
- [ 4.014]pmbus: normal or secure os
- ready
- [ 4.018]PMU: AXP81X
- [ 4.020]PMU: AXP81X found
- bat_vol=0, ratio=100
- [ 4.026]PMU: dcdc2 900
- [ 4.028]PMU: pll1 1008 Mhz
- AXI0=336 Mhz,PLL_PERIPH =1200 Mhz AHB1=200 Mhz, APB1=100 Mhz
- set power on vol to default
- dcdc1_vol = 3300, onoff=1
- dcdc2_vol = 900, onoff=1
- dcdc3_vol = 900, onoff=1
- dcdc4_vol = 900, onoff=1
- dcdc6_vol = 900, onoff=1
- aldo1_vol = 1800, onoff=0
- aldo2_vol = 1800, onoff=1
- aldo3_vol = 3000, onoff=1
- eldo2_vol = 1800, onoff=0
- dldo1_vol = 3300, onoff=0
- dldo2_vol = 3300, onoff=0
- dldo3_vol = 2500, onoff=1
- dldo4_vol = 2800, onoff=0
- fldo2_vol = 900, onoff=1
- find power_sply to end
- supply=dcdc1
- axp=axp81x, supply=dcdc1, vol=3300
- reg addr=0x1c20b04, value=0xd, pmu_vol=3300
- supply=dcdc1
- axp=axp81x, supply=dcdc1, vol=3300
- reg addr=0x1c20b08, value=0xd, pmu_vol=3300
- supply=dldo3
- axp=axp81x, supply=dldo3, vol=1800
- reg addr=0x1c20b0c, value=0x0, pmu_vol=1800
- supply=dcdc1
- axp=axp81x, supply=dcdc1, vol=3300
- reg addr=0x1c20b10, value=0xd, pmu_vol=3300
- supply=dcdc1
- axp=axp81x, supply=dcdc1, vol=3300
- reg addr=0x1c20b14, value=0xd, pmu_vol=3300
- supply=dcdc1
- axp=axp81x, supply=dcdc1, vol=3300
- reg addr=0x1c20b18, value=0xd, pmu_vol=3300
- supply=dcdc1
- axp=axp81x, supply=dcdc1, vol=3300
- reg addr=0x1c20b1c, value=0xd, pmu_vol=3300
- supply=aldo3
- axp=axp81x, supply=aldo3, vol=3000
- reg addr=0x1f02f00, value=0xa, pmu_vol=3000
- config gpio bias voltage finish
- vbus exist
- no battery, limit to dc
- ac100 reg 0x00 = 0x101
- ac100 reg 0xd0 = 0x0
- ac100 reg 0xd1 = 0x0
- dram_para_set start
- dram_para_set end
- [ 4.234]DRAM: 512 MiB
- relocation Offset is: 15af9000
- gic: normal or no secure os mode
- workmode = 16
- NAND_UbootProbe start
- NB1 : enter phy init
- NandHwInit: Start Nand Hardware initializing .....
- uboot:physical version: 2 20 20141023 1122
- [NAND] channel cnt is 1
- ndfc version: 1
- ndfc dma mode: MBUS DMA
- Reset NDFC 0
- NFC Randomizer start.
- NFC_ResetChip: 0x101, 0x100 0x10095
- NFC_ResetChip: 0xff, ch: 0
- [PHY_DBG] CH 0 Nand flash chip id is:0x0 0x0 0x0 0x0 0x0 0x0
- nand id of two channel is not the same, set to 1 channel mode
- [SCAN_DBG] Nand flash chip id is:0x0 0x0 0x0 0x0 0x0 0x0
- [SCAN_ERR] search nand physical architecture parameter failed!
- [ERR]NandHwInit: SCN_AnalyzeNandSystem() failed!
- NandHwInit: End Nand Hardware initializing ..... FAIL!
- NB1 : nand phy init fail
- NB1 : enter phy Exit
- nand release dma:0
- NAND_UbootProbe end: 0xffffffff
- try nand fail
- [ 4.351][mmc]: mmc driver ver 2015-04-13 14:50:00
- [ 4.356][mmc]: get sdc_phy_wipe fail.
- [ 4.360][mmc]: get sdc0 sdc_erase fail.
- [ 4.364][mmc]: get sdc_2xmode ok, val = 1
- [ 4.368][mmc]: get sdc_ddrmode ok, val = 1
- [ 4.372][mmc]: get sdc_f_max fail,use default 50000000Hz
- [ 4.378][mmc]: get card_line ok, card_line = 8
- [ 4.383][mmc]: get sdc_ex_dly_used fail,use default
- [ 4.388][mmc]: SUNXI SD/MMC: 2
- [ 4.401][mmc]: *Try SD card 2*
- [ 4.404][mmc]: mmc 2 cmd 8 err 100
- [ 4.410][mmc]: mmc send if cond failed
- [ 4.414][mmc]: mmc 2 cmd 55 err 100
- [ 4.419][mmc]: send app cmd failed
- [ 4.422][mmc]: *Try MMC card 2*
- [ 4.489][mmc]: mmc re-update_phase
- [ 4.494][mmc]: mmc re-update_phase
- [ 4.499][mmc]: mmc re-update_phase
- [ 4.504][mmc]: ddr8
- [ 4.506][mmc]: mmc re-update_phase
- [ 4.519][mmc]: CID 0x1501004d 0x38473147 0x4303dc0d 0xb061506f
- [ 4.524][mmc]: MMC ver 4.5
- [ 4.527][mmc]: mmc clk 50000000
- [ 4.530][mmc]: SD/MMC Card: 8bit, capacity: 7456MB
- [ 4.535][mmc]: boot0 capacity: 4000KB,boot1 capacity: 4000KB
- [ 4.541][mmc]: ***SD/MMC 2 init OK!!!***
- [ 4.546][mmc]: erase_grp_size:0x400WrBlk * 0x200 = 0x80000 Byte
- [ 4.552][mmc]: secure_feature 0x55
- [ 4.555][mmc]: secure_removal_type 0x0
- read flash error
- out of usb burn from boot: not boot mode
- In: serial
- Out: serial
- Err: serial
- --------fastboot partitions--------
- mbr not exist
- [ 4.573]Hit any key to stop autoboot: 0
- work mode=0x10
- run usb efex
- buf queue page size = 65536
- delay time 2500
- usb init ok
- set address 0x19
- SUNXI_EFEX_ERASE_TAG
- erase_flag = 0x1
- FEX_CMD_fes_verify_status
- FEX_CMD_fes_verify last err=0
- the 0 mbr table is ok
- the 1 mbr table is ok
- the 2 mbr table is ok
- the 3 mbr table is ok
- *************MBR DUMP***************
- total mbr part 11
- part[0] name :bootloader
- part[0] classname :DISK
- part[0] addrlo :0x8000
- part[0] lenlo :0x8000
- part[0] user_type :32768
- part[0] keydata :0
- part[0] ro :0
- part[1] name :env
- part[1] classname :DISK
- part[1] addrlo :0x10000
- part[1] lenlo :0x8000
- part[1] user_type :32768
- part[1] keydata :0
- part[1] ro :0
- part[2] name :boot
- part[2] classname :DISK
- part[2] addrlo :0x18000
- part[2] lenlo :0x8000
- part[2] user_type :32768
- part[2] keydata :0
- part[2] ro :0
- part[3] name :system
- part[3] classname :DISK
- part[3] addrlo :0x20000
- part[3] lenlo :0x300000
- part[3] user_type :32768
- part[3] keydata :0
- part[3] ro :0
- part[4] name :misc
- part[4] classname :DISK
- part[4] addrlo :0x320000
- part[4] lenlo :0x8000
- part[4] user_type :32768
- part[4] keydata :0
- part[4] ro :0
- part[5] name :recovery
- part[5] classname :DISK
- part[5] addrlo :0x328000
- part[5] lenlo :0x10000
- part[5] user_type :32768
- part[5] keydata :0
- part[5] ro :0
- part[6] name :cache
- part[6] classname :DISK
- part[6] addrlo :0x338000
- part[6] lenlo :0x180000
- part[6] user_type :32768
- part[6] keydata :0
- part[6] ro :0
- part[7] name :metadata
- part[7] classname :DISK
- part[7] addrlo :0x4b8000
- part[7] lenlo :0x8000
- part[7] user_type :32768
- part[7] keydata :0
- part[7] ro :0
- part[8] name :private
- part[8] classname :DISK
- part[8] addrlo :0x4c0000
- part[8] lenlo :0x8000
- part[8] user_type :32768
- part[8] keydata :0
- part[8] ro :0
- part[9] name :alog
- part[9] classname :DISK
- part[9] addrlo :0x4c8000
- part[9] lenlo :0x28000
- part[9] user_type :32768
- part[9] keydata :0
- part[9] ro :0
- part[10] name :UDISK
- part[10] classname :DISK
- part[10] addrlo :0x4f0000
- part[10] lenlo :0x0
- part[10] user_type :33024
- part[10] keydata :0
- part[10] ro :0
- total part: 12
- mbr 0, 8000, 8000
- bootloader 1, 8000, 8000
- env 2, 8000, 8000
- boot 3, 8000, 8000
- system 4, 300000, 8000
- misc 5, 8000, 8000
- recovery 6, 10000, 8000
- cache 7, 180000, 8000
- metadata 8, 8000, 8000
- private 9, 8000, 8000
- alog 10, 28000, 8000
- UDISK 11, 0, 8100
- do need erase flash
- private part exist
- the 0 mbr table is bad
- the mbr on flash is bad
- [ 7.750][mmc]: mmc start mass pro boot part...
- [ 7.758][mmc]: mmc re-update_phase
- [ 7.762][mmc]: mmc re-update_phase
- [ 7.766][mmc]: mmc re-update_phase
- [ 7.778][mmc]: mmc re-update_phase
- [ 7.782][mmc]: mmc start write user part after write boot part...
- erase boot0, size:32k, write 0x00
- erase env part
- [ 7.795][mmc]: erase from: 106496, to: 139263, cnt: 32768, erase_group: 1024
- [ 7.808][mmc]: mmc_send_cmd: cmd 38 wait rsp busy 0x85a us
- erase boot part
- [ 7.815][mmc]: erase from: 139264, to: 172031, cnt: 32768, erase_group: 1024
- [ 7.827][mmc]: mmc_send_cmd: cmd 38 wait rsp busy 0x767 us
- erase system part
- [ 7.835][mmc]: erase from: 172032, to: 3317759, cnt: 3145728, erase_group: 1024
- [ 8.127][mmc]: mmc_send_cmd: cmd 38 wait rsp busy 0x19b14 us
- erase misc part
- [ 8.134][mmc]: erase from: 3317760, to: 3350527, cnt: 32768, erase_group: 1024
- [ 8.147][mmc]: mmc_send_cmd: cmd 38 wait rsp busy 0x766 us
- erase recovery part
- [ 8.154][mmc]: erase from: 3350528, to: 3416063, cnt: 65536, erase_group: 1024
- [ 8.170][mmc]: mmc_send_cmd: cmd 38 wait rsp busy 0xb97 us
- erase cache part
- [ 8.177][mmc]: erase from: 3416064, to: 4988927, cnt: 1572864, erase_group: 1024
- [ 8.332][mmc]: mmc_send_cmd: cmd 38 wait rsp busy 0xd40a us
- erase metadata part
- [ 8.339][mmc]: erase from: 4988928, to: 5021695, cnt: 32768, erase_group: 1024
- [ 8.352][mmc]: mmc_send_cmd: cmd 38 wait rsp busy 0x766 us
- erase private part
- [ 8.359][mmc]: erase from: 5021696, to: 5054463, cnt: 32768, erase_group: 1024
- [ 8.372][mmc]: mmc_send_cmd: cmd 38 wait rsp busy 0x766 us
- erase alog part
- [ 8.379][mmc]: erase from: 5054464, to: 5218303, cnt: 163840, erase_group: 1024
- [ 8.403][mmc]: mmc_send_cmd: cmd 38 wait rsp busy 0x1829 us
- erase UDISK part
- sunxi_sprite_mmc_phyerase: @nr is 0, erase from @from to end
- [ 8.416][mmc]: erase from: 5218304, to: 15268863, cnt: 10050560, erase_group: 1024
- [ 9.021][mmc]: mmc_send_cmd: cmd 38 wait rsp busy 0x35d0d us
- [ 9.026][mmc]: mmc_mmc_erase: some sectors in emmc are ignored!
- [ 9.032][mmc]: --0: from15268864 nr1023
- write zeros-0: from 0xe8fc00 to 0xe8fffe
- [ 9.040][mmc]: mmc start mass pro boot part...
- [ 9.045][mmc]: boot0 start address 15268864
- card erase all
- SUNXI_EFEX_MBR_TAG
- mbr size = 0x10000
- begin to write standard mbr
- [ 9.090][mmc]: mmc start mass pro boot part...
- [ 9.095][mmc]: boot0 start address 1
- [ 9.100][mmc]: mmc start mass pro boot part...
- [ 9.104][mmc]: boot0 start address 2
- [ 9.109][mmc]: mmc start mass pro boot part...
- [ 9.113][mmc]: boot0 start address 3
- [ 9.118][mmc]: mmc start mass pro boot part...
- [ 9.123][mmc]: boot0 start address 4
- [ 9.127][mmc]: mmc start mass pro boot part...
- [ 9.132][mmc]: boot0 start address 5
- [ 9.137][mmc]: mmc start mass pro boot part...
- [ 9.141][mmc]: boot0 start address 6
- [ 9.146][mmc]: mmc start mass pro boot part...
- [ 9.150][mmc]: boot0 start address 7
- [ 9.155][mmc]: mmc start mass pro boot part...
- [ 9.160][mmc]: boot0 start address 8
- [ 9.165][mmc]: mmc start mass pro boot part...
- [ 9.169][mmc]: boot0 start address 9
- [ 9.174][mmc]: mmc start mass pro boot part...
- [ 9.178][mmc]: boot0 start address 0
- successed to write standard mbr
- FEX_CMD_fes_verify_status
- FEX_CMD_fes_verify last err=0
- flash sectors: 0xe90000
- FEX_CMD_fes_verify_value, start 0x8000, size high 0x0:low 0x6f6400
- FEX_CMD_fes_verify_value 0x7f81840e
- FEX_CMD_fes_verify_value, start 0x10000, size high 0x0:low 0x20000
- FEX_CMD_fes_verify_value 0x338e87e9
- FEX_CMD_fes_verify_value, start 0x18000, size high 0x0:low 0xce2800
- FEX_CMD_fes_verify_value 0xf80f8cdc
- FEX_CMD_fes_verify_value, start 0x328000, size high 0x0:low 0xdc4000
- FEX_CMD_fes_verify_value 0x75875e50
- SUNXI_EFEX_BOOT1_TAG
- boot1 size = 0xd4000
- uboot size = 0xd4000
- storage type = 2
- mmc down uboot
- [ 86.152][mmc]: mmc start mass pro boot part...
- [ 86.156][mmc]: boot0 start address 32800
- FEX_CMD_fes_verify_status
- FEX_CMD_fes_verify last err=0
- SUNXI_EFEX_BOOT0_TAG
- boot0 size = 0x8000
- dram para[0] = 2dc
- dram para[1] = 7
- dram para[2] = 3bfb
- dram para[3] = 1
- dram para[4] = 10f40800
- dram para[5] = 1000
- dram para[6] = 0
- dram para[7] = c3
- dram para[8] = a
- dram para[9] = 2
- dram para[10] = 49a25a
- dram para[11] = 1b1b290
- dram para[12] = 4d02c
- dram para[13] = 0
- dram para[14] = 0
- dram para[15] = 0
- dram para[16] = 0
- dram para[17] = 0
- dram para[18] = 1
- dram para[19] = 5008888
- dram para[20] = 8888
- dram para[21] = 5005
- dram para[22] = 0
- dram para[23] = c01
- dram para[24] = 0
- dram para[25] = 0
- dram para[26] = 0
- dram para[27] = 0
- dram para[28] = 0
- dram para[29] = 0
- dram para[30] = 0
- dram para[31] = 0
- storage type = 2
- [ 86.263][mmc]: mmc start mass pro boot part...
- [ 86.268][mmc]: mmc re-update_phase
- [ 86.271][mmc]: mmc re-update_phase
- [ 86.275][mmc]: mmc re-update_phase
- [ 86.282][mmc]: mmc re-update_phase
- [ 86.285][mmc]: mmc start write user part after write boot part...
- FEX_CMD_fes_verify_status
- FEX_CMD_fes_verify last err=0
- sunxi_efex_next_action=2
- exit usb
- next work 2
- SUNXI_UPDATE_NEXT_ACTION_REBOOT
- set next mode 14
- drv_disp_exit
- [ 86.345][mmc]: mmc exit start
- [ 86.357][mmc]: mmc 2 cmd 8 err 100
- [ 86.362][mmc]: mmc send if cond failed
- [ 86.366][mmc]: mmc 2 cmd 55 err 100
- [ 86.371][mmc]: send app cmd failed
- [ 86.383][mmc]: get sdc_phy_wipe fail.
- [ 86.387][mmc]: get sdc0 sdc_erase fail.
- [ 86.391][mmc]: get sdc_2xmode ok, val = 1
- [ 86.395][mmc]: get sdc_ddrmode ok, val = 1
- [ 86.399][mmc]: get sdc_f_max fail,use default 50000000Hz
- [ 86.404][mmc]: get card_line ok, card_line = 8
- [ 86.409][mmc]: get sdc_ex_dly_used fail,use default
- [ 86.414][mmc]: mmc 2 exit ok
- HELLO! BOOT0 is starting!
- boot0 version : 4.0.0
- rtc[1] value = 0x00010000
- rtc[2] value = 0x00020000
- rtc[3] value = 0x00030000
- DRAM DRIVE INFO: V1.1
- DRAM Type =7 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
- DRAM normal_mode value: 00000001
- DRAM CLK =732 MHZ
- rsb_send_initseq: rsb clk 400Khz -> 3Mhz
- PMU: AXP81X
- ddr voltage = 1200 mv
- ID CHECK VERSION: V0.2
- using ic A83T
- using axp AXP813
- DRAM zq value: 00003bfb
- dram size =2048
- card boot number = 2
- card no is 2
- sdcard 2 line count 8
- [mmc]: mmc driver ver 2015-04-13 16:05:39
- [mmc]: ***Try SD card 2***
- [mmc]: mmc 2 cmd 8 err 00000100
- [mmc]: mmc 2 cmd 8 err 00000100
- [mmc]: mmc 2 send if cond failed
- [mmc]: mmc 2 cmd 55 err 00000100
- [mmc]: mmc 2 cmd 55 err 00000100
- [mmc]: mmc 2 send app cmd failed
- [mmc]: ***Try MMC card 2***
- [mmc]: mmc re-update_phase
- [mmc]: mmc re-update_phase
- [mmc]: 8bit ddr!!!
- [mmc]: mmc re-update_phase
- [mmc]: MMC ver 4.5
- [mmc]: SD/MMC Card: 8bit, capacity: 7456MB
- [mmc]: vendor: Man 00150100 Snr 03dc0db0
- [mmc]: product: M8G1G
- [mmc]: revision: 4.3
- [mmc]: ***SD/MMC 2 init OK!!!***
- sdcard 2 init ok
- The size of uboot is 000d4000.
- sum=d800d490
- src_sum=d800d490
- set_mmc_para,sdly 50M 0
- set_mmc_para,sdly 25M 0
- Succeed in loading uboot from sdmmc flash.
- Ready to disable icache.
- Jump to secend Boot.
- [ 0.204]
- U-Boot 2011.09-rc1-dirty (Nov 05 2015 - 23:11:51) Allwinner Technology
- [ 0.212]version: 2.1.0
- normal mode
- [ 0.288]pmbus: normal or secure os
- ready
- [ 0.292]PMU: AXP81X
- [ 0.294]PMU: AXP81X found
- bat_vol=0, ratio=100
- [ 0.300]PMU: dcdc2 900
- [ 0.302]PMU: pll1 1008 Mhz
- AXI0=336 Mhz,PLL_PERIPH =1200 Mhz AHB1=200 Mhz, APB1=100 Mhz
- set power on vol to default
- dcdc1_vol = 3300, onoff=1
- dcdc2_vol = 900, onoff=1
- dcdc3_vol = 900, onoff=1
- dcdc4_vol = 900, onoff=1
- dcdc6_vol = 900, onoff=1
- aldo1_vol = 1800, onoff=0
- aldo2_vol = 1800, onoff=1
- aldo3_vol = 3000, onoff=1
- eldo2_vol = 1800, onoff=0
- dldo1_vol = 3300, onoff=0
- dldo2_vol = 3300, onoff=0
- dldo3_vol = 2500, onoff=1
- dldo4_vol = 2800, onoff=0
- fldo2_vol = 900, onoff=1
- find power_sply to end
- supply=dcdc1
- axp=axp81x, supply=dcdc1, vol=3300
- reg addr=0x1c20b04, value=0xd, pmu_vol=3300
- supply=dcdc1
- axp=axp81x, supply=dcdc1, vol=3300
- reg addr=0x1c20b08, value=0xd, pmu_vol=3300
- supply=dldo3
- axp=axp81x, supply=dldo3, vol=1800
- reg addr=0x1c20b0c, value=0x0, pmu_vol=1800
- supply=dcdc1
- axp=axp81x, supply=dcdc1, vol=3300
- reg addr=0x1c20b10, value=0xd, pmu_vol=3300
- supply=dcdc1
- axp=axp81x, supply=dcdc1, vol=3300
- reg addr=0x1c20b14, value=0xd, pmu_vol=3300
- supply=dcdc1
- axp=axp81x, supply=dcdc1, vol=3300
- reg addr=0x1c20b18, value=0xd, pmu_vol=3300
- supply=dcdc1
- axp=axp81x, supply=dcdc1, vol=3300
- reg addr=0x1c20b1c, value=0xd, pmu_vol=3300
- supply=aldo3
- axp=axp81x, supply=aldo3, vol=3000
- reg addr=0x1f02f00, value=0xa, pmu_vol=3000
- config gpio bias voltage finish
- vbus exist
- no battery, limit to dc
- ac100 reg 0x00 = 0x101
- ac100 reg 0xd0 = 0x0
- ac100 reg 0xd1 = 0x0
- fel key old mode
- run key detect
- no key found
- no key input
- dram_para_set start
- dram_para_set end
- [ 0.524]DRAM: 2 GiB
- relocation Offset is: 75af9000
- gic: normal or no secure os mode
- script config pll_de to 504 Mhz
- script config pll_video1 to 297 Mhz
- Not Found clk pll_video in script
- enable power vcc-hdmi-18, ret=0
- DRV_DISP_Init end
- [ 0.685]boot_disp.output_disp=1
- [ 0.688]boot_disp.output_type=3
- [ 0.692]boot_disp.output_mode=5
- [ 0.695]fetch script data boot_disp.auto_hpd fail
- disp1 device type(4) enable
- attched ok, mgr1<-->device1, type=4, mode=5----
- ready to set mode
- workmode = 0
- MMC: 2
- [ 0.710][mmc]: mmc driver ver 2015-04-13 14:50:00
- [ 0.715][mmc]: get sdc_phy_wipe fail.
- [ 0.719][mmc]: get sdc0 sdc_erase fail.
- [ 0.723][mmc]: get sdc_2xmode ok, val = 1
- [ 0.727][mmc]: get sdc_ddrmode ok, val = 1
- [ 0.731][mmc]: get sdc_f_max fail,use default 50000000Hz
- [ 0.737][mmc]: get card_line ok, card_line = 8
- [ 0.741][mmc]: get sdc_ex_dly_used fail,use default
- [ 0.747][mmc]: SUNXI SD/MMC: 2
- [ 0.760][mmc]: *Try SD card 2*
- [ 0.763][mmc]: mmc 2 cmd 8 err 100
- [ 0.769][mmc]: mmc send if cond failed
- [ 0.773][mmc]: mmc 2 cmd 55 err 100
- [ 0.778][mmc]: send app cmd failed
- [ 0.781][mmc]: *Try MMC card 2*
- [ 0.821][mmc]: mmc re-update_phase
- [ 0.826][mmc]: mmc re-update_phase
- [ 0.831][mmc]: mmc re-update_phase
- [ 0.836][mmc]: ddr8
- [ 0.838][mmc]: mmc re-update_phase
- [ 0.851][mmc]: CID 0x1501004d 0x38473147 0x4303dc0d 0xb061506f
- [ 0.856][mmc]: MMC ver 4.5
- [ 0.859][mmc]: mmc clk 50000000
- [ 0.862][mmc]: SD/MMC Card: 8bit, capacity: 7456MB
- [ 0.867][mmc]: boot0 capacity: 4000KB,boot1 capacity: 4000KB
- [ 0.873][mmc]: ***SD/MMC 2 init OK!!!***
- [ 0.878][mmc]: erase_grp_size:0x400WrBlk * 0x200 = 0x80000 Byte
- [ 0.883][mmc]: secure_feature 0x55
- [ 0.887][mmc]: secure_removal_type 0x0
- [ 0.891]sunxi flash init ok
- the secure storage map is empty
- no item name key_burned_flag in the map
- sunxi secure storage has no flag
- [ 0.904]usb burn from boot
- delay time 0
- [ 0.975]usb prepare ok
- usb sof ok
- vbus pc exist ,limit to pc
- [ 1.187]usb probe ok
- [ 1.189]usb setup ok
- set address 0x14
- sunxi usb error: received bytes 0x20 is not equal cbw struct size 0x1f
- [ 4.191]timer occur
- [ 4.227]do_burn_from_boot usb : have no handshake
- In: serial
- Out: serial
- Err: serial
- --------fastboot partitions--------
- -total partitions:11-
- -name- -start- -size-
- bootloader : 1000000 1000000
- env : 2000000 1000000
- boot : 3000000 1000000
- system : 4000000 60000000
- misc : 64000000 1000000
- recovery : 65000000 2000000
- cache : 67000000 30000000
- metadata : 97000000 1000000
- private : 98000000 1000000
- alog : 99000000 5000000
- UDISK : 9e000000 0
- -----------------------------------
- base bootcmd=run setargs_nand boot_normal
- bootcmd set setargs_mmc
- key 0
- recovery key high 10, low 8
- cant find fstbt value
- misc partition found
- to be run cmd=run setargs_mmc boot_normal
- ** Unable to use sunxi_flash 8:0 for fatload **
- load file(sn.txt) error
- serial is: 00000000000000000000
- mount part name bootloader
- cant open script.bin, maybe it is not exist
- WORK_MODE_BOOT
- board_status_probe
- [ 4.329]pre sys mode
- sunxi_bmp_logo_display
- [ 4.366][mmc]: blkcnt should not be 0
- [ 4.385]fetch script data boot_disp.output_disp fail
- [ 4.390]screen_id =1, screen_width =1280, screen_height =720
- [ 4.395]frame buffer address 46400000
- [ 4.399]Hit any key to stop autoboot: 0
- read boot or recovery all
- [ 4.574]sunxi flash read :offset 3000000, 14556211 bytes OK
- [ 4.586]ready to boot
- [ 4.588][mmc]: mmc exit start
- [ 4.601][mmc]: mmc 2 cmd 8 err 100
- [ 4.606][mmc]: mmc send if cond failed
- [ 4.610][mmc]: mmc 2 cmd 55 err 100
- [ 4.615][mmc]: send app cmd failed
- [ 4.627][mmc]: get sdc_phy_wipe fail.
- [ 4.631][mmc]: get sdc0 sdc_erase fail.
- [ 4.635][mmc]: get sdc_2xmode ok, val = 1
- [ 4.639][mmc]: get sdc_ddrmode ok, val = 1
- [ 4.643][mmc]: get sdc_f_max fail,use default 50000000Hz
- [ 4.648][mmc]: get card_line ok, card_line = 8
- [ 4.653][mmc]: get sdc_ex_dly_used fail,use default
- [ 4.658][mmc]: mmc 2 exit ok
- [ 4.661]
- Starting kernel ...
- [sun8i_fixup]: From boot, get meminfo:
- Start: 0x40000000
- Size: 2048MB
- ion_carveout reserve: 96m 128m
- ion_reserve_common: ion reserve: [0xb8000000, 0xc0000000]!
- ion_cma reserve: 120m 176m 512m
- ion_reserve_common: ion reserve: [0xa0000000, 0xc0000000]!
- ------sun8i_smp_init_ops----37-----
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement