Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- ▒
- __ __ _ _
- | \/ | __ _ _ ____ _____| | |
- | |\/| |/ _` | '__\ \ / / _ \ | |
- | | | | (_| | | \ V / __/ | |
- |_| |_|\__,_|_| \_/ \___|_|_|
- _ _ ____ _
- | | | | | __ ) ___ ___ | |_
- | | | |___| _ \ / _ \ / _ \| __|
- | |_| |___| |_) | (_) | (_) | |_
- \___/ |____/ \___/ \___/ \__|
- ** MARVELL BOARD: DB-88F6282A-BP LE
- U-Boot 1.1.4 (Jul 18 2013 - 10:47:29) Marvell version: 3.5.9
- U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
- Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz
- SysClock = 533Mhz , TClock = 200Mhz
- DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 24 tRCD=8
- DRAM CS[0] base 0x00000000 size 512MB
- DRAM Total size 512MB 16bit width
- Addresses 10M - 0M are saved for the U-Boot usage.
- Mem malloc Initialization (10M - 7M): Done
- NAND:128 MB
- Flash: 0 kB
- CPU : Marvell Feroceon (Rev 1)
- Kernel address is 0x4640000.
- Streaming disabled
- Write allocate disabled
- USB 0: host mode
- [BlueDBG] reseting SoC Pex[0] 0 ...
- PEX 0: PCI Express Root Complex Interface
- PEX interface detected Link X1
- [BlueDBG] reseting SoC Pex[1] 0 ...
- [BlueDBG] reseting SoC Pex[1] 1 ...
- [BlueDBG] reseting SoC Pex[1] 2 ...
- [BlueDBG] reseting SoC Pex[1] 3 ...
- [BlueDBG] reseting SoC Pex[1] 4 ...
- [BlueDBG] reseting SoC Pex[1] 5 ...
- [BlueDBG] reseting SoC Pex[1] 6 ...
- [BlueDBG] reseting SoC Pex[1] 7 ...
- [BlueDBG] reseting SoC Pex[1] 8 ...
- [BlueDBG] reseting SoC Pex[1] 9 ...
- [BlueDBG] reseting SoC Pex[1] 10 ...
- PEX 1: interface detected no Link.
- Net: egiga0 [PRIME]
- Hit any key to stop autoboot: 0
- Marvell>> printenv
- bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
- bootdelay=2
- baudrate=115200
- loads_echo=0
- ipaddr=10.4.52.165
- serverip=10.4.52.7
- rootpath=/srv/ubuntu
- netmask=255.255.255.0
- nandEcc=1bit
- MODEL_ID=AE03
- PRODUCT_NAME=NSA-325v2
- FEATURE_BIT=00
- CONTRY_TYPE=FF
- VENDOR_NAME=MitraStar Technology Corp.
- run_diag=yes
- arcNumber=4495
- bootargs_stock=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
- bootargs_linux=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8
- bootcmd_linux=setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /uImage; ext2load usb 0:1 0x01100000 /uInitrd; bootm $(loadaddr) 0x01100000
- bootcmd_stock=setenv bootargs $(bootargs_stock); nand read.e $(loadaddr) $(kernel_addr) 0xA00000; bootm $(loadadr)
- to_stock=setenv mainlineLinux no; setenv bootcmd \'run bootcmd_stock\'; saveenv; reset
- to_linux=setenv mainlineLinux yes; setenv bootcmd \'run bootcmd_linux\'; saveenv; reset
- console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)
- ethprime=egiga0
- bootargs_root=root=/dev/nfs rw
- bootargs_end=:::orion:eth0:none
- image_name=uImage
- standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
- lcd0_enable=0
- lcd0_params=640x480-16@60
- ethaddr=00:50:43:00:02:02
- ethmtu=1500
- mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
- mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
- usb0Mode=host
- yuk_ethaddr=00:00:00:EE:51:81
- netretry=no
- rcvrip=169.254.100.100
- loadaddr=0x02000000
- autoload=no
- image_multi=yes
- ethact=egiga0
- bootcmd='run bootcmd_linux'
- stdin=serial
- stdout=serial
- stderr=serial
- mainlineLinux=yes
- enaMonExt=no
- enaCpuStream=no
- enaWrAllo=no
- pexMode=RC
- disL2Cache=no
- setL2CacheWT=yes
- disL2Prefetch=yes
- enaICPref=yes
- enaDCPref=yes
- sata_dma_mode=yes
- netbsd_en=no
- vxworks_en=no
- disaMvPnp=no
- enaAutoRecovery=yes
- kernel_addr=0x4640000
- pcieTune=no
- pcieTune1=no
- Environment size: 2494/131068 bytes
- Marvell>> boot
- (Re)start USB...
- USB: scanning bus for devices... 2 USB Device(s) found
- Waiting for storage device(s) to settle before scanning...
- 0 Storage Device(s) found
- ** Bad partition 1 **
- ** Bad partition 1 **
- ## Booting image at 02000000 ...
- Bad Magic Number
- Marvell>>
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement