osmo-trx trace

---------osmo-trx trace-----------------------------------------------------------------------------------
[INFO] [MULTI_USRP] Setting master clock rate selection to 'manual'.
-- Setting B200/B210 EDGE mode (4 SPS TX/RX) (offset 0.0618462 ms = 16.75 samples)
ERR 140699087988544 19:41:56.3 UHDDevice.cpp:871:open: TS_OFFSET = 67 rx_rate = 1.08333e+06
ERR 140699087988544 19:41:56.3 UHDDevice.cpp:871:open: TS_OFFSET = 67 rx_rate = 1.08333e+06
INFO 140699087988544 19:41:56.3 UHDDevice.cpp:445:init_gains: Supported Tx gain range [0; 89.8]
INFO 140699087988544 19:41:56.3 UHDDevice.cpp:450:init_gains: Supported Rx gain range [0; 76]
INFO 140699087988544 19:41:56.3 UHDDevice.cpp:454:init_gains: Default setting Tx gain for channel 0 to 44.9
INFO 140699087988544 19:41:56.4 UHDDevice.cpp:461:init_gains: Default setting Rx gain for channel 0 to 38
INFO 140699087988544 19:41:56.4 UHDDevice.cpp:878:open:
Single USRP:
  Device: B-Series Device
  Mboard 0: B210
  RX Channel: 0
    RX DSP: 0
    RX Dboard: A
    RX Subdev: FE-RX1
  RX Channel: 1
    RX DSP: 1
    RX Dboard: A
    RX Subdev: FE-RX2
  TX Channel: 0
    TX DSP: 0
    TX Dboard: A
    TX Subdev: FE-TX1
  TX Channel: 1
    TX DSP: 1
    TX Dboard: A
    TX Subdev: FE-TX2
ALERT 140699087988544 19:41:57.4 UHDDevice.cpp:937:flush_recv: Device timed out
ALERT 140699087988544 19:41:57.4 UHDDevice.cpp:937:flush_recv: Device timed out
-- Transceiver active with 1 channel(s)
INFO 140699088361216 19:42:23.0 Transceiver.cpp:1040:writeClockInterface: ClockInterface: sending IND CLOCK 2513128
INFO 140699088361216 19:42:23.0 Transceiver.cpp:732:driveControl: command is CMD POWEROFF
INFO 140699088361216 19:42:23.1 Transceiver.cpp:1040:writeClockInterface: ClockInterface: sending IND CLOCK 2513128
INFO 140699088361216 19:42:23.1 Transceiver.cpp:732:driveControl: command is CMD POWEROFF
INFO 140699088361216 19:42:23.4 Transceiver.cpp:1040:writeClockInterface: ClockInterface: sending IND CLOCK 2513128
INFO 140699088361216 19:42:23.4 Transceiver.cpp:732:driveControl: command is CMD RXTUNE 880200
[INFO] SetFrequency using cache values vco:2, csw:141
INFO 140699088361216 19:42:23.4 UHDDevice.cpp:1301:set_freq:
Tune Result:
    Target RF  Freq: 880.200000 (MHz)
    Actual RF  Freq: 880.200000 (MHz)
    Target DSP Freq: 0.000000 (MHz)
    Actual DSP Freq: 0.000000 (MHz)

INFO 140699088361216 19:42:23.4 Transceiver.cpp:1040:writeClockInterface: ClockInterface: sending IND CLOCK 2513128
INFO 140699088361216 19:42:23.4 Transceiver.cpp:732:driveControl: command is CMD TXTUNE 925200
[INFO] SetFrequency using cache values vco:2, csw:202
INFO 140699088361216 19:42:23.4 UHDDevice.cpp:1301:set_freq:
Tune Result:
    Target RF  Freq: 925.200000 (MHz)
    Actual RF  Freq: 925.200000 (MHz)
    Target DSP Freq: -0.000000 (MHz)
    Actual DSP Freq: 0.000000 (MHz)

INFO 140699088361216 19:42:23.4 Transceiver.cpp:1040:writeClockInterface: ClockInterface: sending IND CLOCK 2513128
INFO 140699088361216 19:42:23.4 Transceiver.cpp:732:driveControl: command is CMD SETTSC 7
INFO 140699088361216 19:42:23.4 Transceiver.cpp:1040:writeClockInterface: ClockInterface: sending IND CLOCK 2513128
INFO 140699088361216 19:42:23.4 Transceiver.cpp:732:driveControl: command is CMD POWERON
NOTICE 140699088361216 19:42:23.4 Transceiver.cpp:254:start: Starting the transceiver
INFO 140699088361216 19:42:23.4 radioInterface.cpp:182:start: Starting radio device
INFO 140699088361216 19:42:23.4 UHDDevice.cpp:972:start: Starting USRP...
INFO 140699088361216 19:42:23.4 UHDDevice.cpp:947:flush_recv: Initial timestamp 22440
INFO 140699088361216 19:42:23.4 UHDDevice.cpp:992:start: The current time is 0.0216554 seconds
INFO 140699088361216 19:42:23.4 radioInterface.cpp:201:start: Radio started
INFO 140699088361216 19:42:23.4 Transceiver.cpp:1040:writeClockInterface: ClockInterface: sending IND CLOCK 2513128
INFO 140699088361216 19:42:23.4 Transceiver.cpp:1040:writeClockInterface: ClockInterface: sending IND CLOCK 2513128
INFO 140699088361216 19:42:23.4 Transceiver.cpp:732:driveControl: command is CMD SETPOWER 0
ERR 140699088295680 19:42:23.5 UHDDevice.cpp:1027:check_rx_md_err: No packet received, implementation timed-out
ERR 140699088295680 19:42:23.5 UHDDevice.cpp:1027:check_rx_md_err: No packet received, implementation timed-out
ALERT 140699088295680 19:42:23.5 UHDDevice.cpp:1031:check_rx_md_err: UHD: Receive timed out
ALERT 140699088295680 19:42:23.5 UHDDevice.cpp:1031:check_rx_md_err: UHD: Receive timed out
ALERT 140699088295680 19:42:23.5 radioInterface.cpp:374:pullBuffer: Receive error 0
ALERT 140699088295680 19:42:23.5 radioInterface.cpp:374:pullBuffer: Receive error 0
ERR 140699088295680 19:42:23.6 UHDDevice.cpp:1027:check_rx_md_err: No packet received, implementation timed-out
ERR 140699088295680 19:42:23.6 UHDDevice.cpp:1027:check_rx_md_err: No packet received, implementation timed-out
ALERT 140699088295680 19:42:23.6 UHDDevice.cpp:1031:check_rx_md_err: UHD: Receive timed out
ALERT 140699088295680 19:42:23.6 UHDDevice.cpp:1031:check_rx_md_err: UHD: Receive timed out
ALERT 140699088295680 19:42:23.6 radioInterface.cpp:374:pullBuffer: Receive error 0
ALERT 140699088295680 19:42:23.6 radioInterface.cpp:374:pullBuffer: Receive error 0
ERR 140699088295680 19:42:23.7 UHDDevice.cpp:1027:check_rx_md_err: No packet received, implementation timed-out
ERR 140699088295680 19:42:23.7 UHDDevice.cpp:1027:check_rx_md_err: No packet received, implementation timed-out
ALERT 140699088295680 19:42:23.7 UHDDevice.cpp:1031:check_rx_md_err: UHD: Receive timed out
ALERT 140699088295680 19:42:23.7 UHDDevice.cpp:1031:check_rx_md_err: UHD: Receive timed out
ALERT 140699088295680 19:42:23.7 radioInterface.cpp:374:pullBuffer: Receive error 0
ALERT 140699088295680 19:42:23.7 radioInterface.cpp:374:pullBuffer: Receive error 0