API tools faq
paste
Advertisement
Guest User

Sane clockspeed/voltage settings for H3 SoC (Orange Pi PC)

a guest
Nov 18th, 2015
732
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 49.86 KB | None | 0 0
raw download clone embed print report
  1. ;Attempt to provide sane clockspeed/voltage settings for H3 SoC (Orange Pi PC)
  2. ;---------------------------------------------------------------------------------------------------------
  3.  
  4. [product]
  5. version = "100"
  6. machine = "orangepi-pc"
  7.  
  8. ;---------------------------------------------------------------------------------------------------------
  9. ; eraseflag - 1 erase data partition, 0 - do not erase data partition
  10. ; next_work - action after burn, 0x0 by config, 0x1, normal, 0x2 reboot 0x3 ,shutdown,0x4 reupdate ,0x5 boot
  11. ;---------------------------------------------------------------------------------------------------------
  12. [platform]
  13. debug_mode = 1
  14. eraseflag = 1
  15. next_work = 2
  16.  
  17. ;----------------------------------------------------------------------------------
  18. ;[target] system bootup configuration
  19. ;boot_clock = CPU boot frequency, Unit: MHz
  20. ;storage_type = boot medium, 0-nand, 1-card0, 2-card2, -1(defualt)auto scan
  21. ;----------------------------------------------------------------------------------
  22. [target]
  23. boot_clock = 1008
  24. storage_type = -1
  25.  
  26. ;---------------------------------------------------------------------------------
  27. ; uboot key detect enable
  28. ; 当keyen_flag = 1 时，支持按键检测
  29. ; 当keyen_flag = 0 时，不支持
  30. ;---------------------------------------------------------------------------------
  31. [key_detect_en]
  32. keyen_flag = 0
  33.  
  34. ;---------------------------------------------------------------------------------
  35. ;"一键进烧写功能"的按键值配置，按住位于min~max范围内的按键都可以强制进烧写
  36. ; fel_key_max用于配置按键的最大键值
  37. ; fel_key_min用于配置按键的最小键值
  38. ;---------------------------------------------------------------------------------
  39. [fel_key]
  40. fel_key_max =07
  41. fel_key_min =02
  42.  
  43. ;----------------------------------------------------------------------------------
  44. ;card boot
  45. ;logical_start用于配置启动卡上mbr的位置相对于SD卡sector 0的偏移，单位为sector(512byte)
  46. ;sprite_gpio0用于配置卡量产时指示灯所用的gpio
  47. ;----------------------------------------------------------------------------------
  48. ;-------------------------------------------------------------------------------
  49. ; sprite_work_delay :
  50. ; sprite_err_delay :
  51. ; sprite_gpio0 ： 卡量产、一键recovery状态指示灯
  52. ; next_work ： 卡量产完成，工作状态(默认关机)
  53. ;-------------------------------------------------------------------------------
  54. [card_boot]
  55. logical_start = 40960
  56. sprite_work_delay = 500
  57. sprite_err_delay = 200
  58. sprite_gpio0 = port:PA15<1><default><default><default>
  59. next_work = 3
  60.  
  61. ;---------------------------------------------------------------------------------
  62. ; used : 1: used this config, 0: not
  63. ; start_type : 1: start system directly when power supply, 0: wait IR/KEY to power on
  64. ; irkey_used : 1: ir key used, 0: not
  65. ; pmukey_used: 1: physical button used, 0: not
  66. ; led_power : 1: light, 0: off
  67. ; led_state : 1: light, 0: off
  68. ;---------------------------------------------------------------------------------
  69. [box_start_os]
  70. used = 1
  71. start_type = 1
  72. irkey_used = 1
  73. pmukey_used = 1
  74. pmukey_num = 3
  75. led_power = 0
  76. led_state = 0
  77.  
  78. ;-------------------------------------------------------------------------------
  79. ; boot阶段上电初始化GPIO
  80. ; used :模块使能端 置1：开启模块 置0：关闭模块
  81. ; gpiox ：上电初始化gpio （名称自定，但不能重复，并且GPIO允许可以多个）
  82. ; PH06 : 系统显示LED GPIO
  83. ;-------------------------------------------------------------------------------
  84. [boot_init_gpio]
  85. used = 1
  86. gpio0 = port:PA15<1><default><default><1>
  87. gpio1 = port:PG11<1><default><default><1>
  88.  
  89. ;----------------------------------------------------------------------------------
  90. ; used: 模块使能端 1：开启模块 0：关闭模块
  91. ; mode: 模式选择 1：一键进入OTA升级 2：一键恢复（通过sysrecovery分区来恢复） 其他值：无效
  92. ; recovery_key ： 按键配置 （例如：recovery_key= port:PH16<0><default>）
  93. ;----------------------------------------------------------------------------------
  94. [recovery_para]
  95. used = 1
  96. mode = 2
  97. recovery_key = port:PL04<0><default><default><default>
  98.  
  99.  
  100. ;---------------------------------------------------------------------------------------------------------
  101. ; if 1 == standby_mode, then support super standby;
  102. ; else, support normal standby.
  103. ;---------------------------------------------------------------------------------------------------------
  104. [pm_para]
  105. standby_mode = 1
  106.  
  107. [card0_boot_para]
  108. card_ctrl = 0
  109. card_high_speed = 1
  110. card_line = 4
  111. sdc_d1 = port:PF00<2><1><2><default>
  112. sdc_d0 = port:PF01<2><1><2><default>
  113. sdc_clk = port:PF02<2><1><2><default>
  114. sdc_cmd = port:PF03<2><1><2><default>
  115. sdc_d3 = port:PF04<2><1><2><default>
  116. sdc_d2 = port:PF05<2><1><2><default>
  117.  
  118. [card2_boot_para]
  119. card_ctrl = 2
  120. card_high_speed = 1
  121. card_line = 8
  122. sdc_cmd = port:PC06<3><1><2><default>
  123. sdc_clk = port:PC05<3><1><2><default>
  124. sdc_d0 = port:PC08<3><1><2><default>
  125. sdc_d1 = port:PC09<3><1><2><default>
  126. sdc_d2 = port:PC10<3><1><2><default>
  127. sdc_d3 = port:PC11<3><1><2><default>
  128. sdc_d4 = port:PC12<3><1><2><default>
  129. sdc_d5 = port:PC13<3><1><2><default>
  130. sdc_d6 = port:PC14<3><1><2><default>
  131. sdc_d7 = port:PC15<3><1><2><default>
  132. sdc_2xmode = 1
  133. sdc_ddrmode = 1
  134.  
  135. [twi_para]
  136. twi_port = 0
  137. twi_scl = port:PA11<2><default><default><default>
  138. twi_sda = port:PA12<2><default><default><default>
  139.  
  140. [uart_para]
  141. uart_debug_port = 0
  142. uart_debug_tx = port:PA04<2><1><default><default>
  143. uart_debug_rx = port:PA05<2><1><default><default>
  144.  
  145. [force_uart_para]
  146. force_uart_port = 0
  147. force_uart_tx = port:PF02<3><1><default><default>
  148. force_uart_rx = port:PF04<3><1><default><default>
  149.  
  150. [jtag_para]
  151. jtag_enable = 0
  152. jtag_ms = port:PA00<3><default><default><default>
  153. jtag_ck = port:PA01<3><default><default><default>
  154. jtag_do = port:PA02<3><default><default><default>
  155. jtag_di = port:PA03<3><default><default><default>
  156.  
  157. [clock]
  158. pll_video = 297
  159. pll_ve = 402
  160. pll_periph0 = 600
  161. pll_gpu = 576
  162. pll_periph1 = 600
  163. pll_de = 864
  164.  
  165. ;*****************************************************************************
  166. ;sdram configuration
  167. ;
  168. ;dram_para2 = 0x00001200 ;Representative enable dram Dual
  169. ;
  170. ;dram_para2 = 0x00001100 ;on behalf of a single channel is enabled dram
  171. ;
  172. ;*****************************************************************************
  173. [dram_para]
  174. dram_clk = 480
  175. dram_type = 3
  176. dram_zq = 0x3b3bfb
  177. dram_odt_en = 0x1
  178. dram_para1 = 0x10E40000
  179. dram_para2 = 0x0000
  180. dram_mr0 = 0x1840
  181. dram_mr1 = 0x40
  182. dram_mr2 = 0x18
  183. dram_mr3 = 0x2
  184. dram_tpr0 = 0x0048A192
  185. dram_tpr1 = 0x01C2418D
  186. dram_tpr2 = 0x00076051
  187. dram_tpr3 = 0
  188. dram_tpr4 = 0
  189. dram_tpr5 = 0
  190. dram_tpr6 = 100
  191. dram_tpr7 = 0
  192. dram_tpr8 = 0
  193. dram_tpr9 = 0
  194. dram_tpr10 = 0
  195. dram_tpr11 = 0x6aaa0000
  196. dram_tpr12 = 0x7979
  197. dram_tpr13 = 0x800800
  198. ;----------------------------------------------------------------------------------
  199. ;os life cycle para configuration
  200. ;----------------------------------------------------------------------------------
  201.  
  202. ;---------------------------------------------------------------------------------------------------------
  203. ; wakeup_src_para:
  204. ; sometimes, u would like to add more wakeup src in standby mode, these para will be
  205. ; help;
  206. ; u need to make sure the standby mode support the wakeup src. Also, some hw
  207. ; condition must be guaranteed.
  208. ; including:
  209. ; cpu_en: power on or off.
  210. ; 1: mean power on
  211. ; 0: mean power off
  212. ; cpu_freq: indicating lowest freq. unit is Mhz;
  213. ; dram selfresh_en: selfresh or not.
  214. ; 1: enable enter selfresh
  215. ; 0: disable enter selfresh
  216. ; dram_pll: if not enter selfresh, indicating lowest freq. unit is Mhz;
  217. ; wakeup_src: to make the scenario work, the wakeup src is needed.
  218. ;---------------------------------------------------------------------------------------------------------
  219. [wakeup_src_para]
  220. cpu_en = 0
  221. cpu_freq = 48
  222. ; (cpu:apb:ahb)
  223. pll_ratio = 0x111
  224. dram_selfresh_en = 1
  225. dram_freq = 36
  226. wakeup_src0 =
  227. wakeup_src_wl = port:PG10<4><default><default><0>
  228. ;wakeup_src_bt = port:PL03<6><default><default><0>
  229.  
  230. ;----------------------------------------------------------------------------------
  231. ;i2c configuration
  232. ;----------------------------------------------------------------------------------
  233. [twi0]
  234. twi_used = 1
  235. twi_scl = port:PA11<2><default><default><default>
  236. twi_sda = port:PA12<2><default><default><default>
  237.  
  238. [twi1]
  239. twi_used = 1
  240. twi_scl = port:PA18<3><default><default><default>
  241. twi_sda = port:PA19<3><default><default><default>
  242.  
  243. [twi2]
  244. twi_used = 0
  245. twi_scl = port:PE12<3><default><default><default>
  246. twi_sda = port:PE13<3><default><default><default>
  247.  
  248. ;----------------------------------------------------------------------------------
  249. ;uart configuration
  250. ;uart_type --- 2 (2 wire), 4 (4 wire), 8 (8 wire, full function)
  251. ;----------------------------------------------------------------------------------
  252. [uart0]
  253. uart_used = 1
  254. uart_port = 0
  255. uart_type = 2
  256. uart_tx = port:PA04<2><1><default><default>
  257. uart_rx = port:PA05<2><1><default><default>
  258.  
  259. [uart1]
  260. uart_used = 0
  261. uart_port = 1
  262. uart_type = 2
  263. uart_tx = port:PG06<2><1><default><default>
  264. uart_rx = port:PG07<2><1><default><default>
  265. uart_rts = port:PG08<2><1><default><default>
  266. uart_cts = port:PG09<2><1><default><default>
  267.  
  268. [uart2]
  269. uart_used = 1
  270. uart_port = 2
  271. uart_type = 4
  272. uart_tx = port:PA00<2><1><default><default>
  273. uart_rx = port:PA01<2><1><default><default>
  274. uart_rts = port:PA02<2><1><default><default>
  275. uart_cts = port:PA03<2><1><default><default>
  276.  
  277. [uart3]
  278. uart_used = 1
  279. uart_port = 3
  280. uart_type = 2
  281. uart_tx = port:PA13<3><1><default><default>
  282. uart_rx = port:PA14<3><1><default><default>
  283. uart_rts = port:PA15<3><1><default><default>
  284. uart_cts = port:PA16<3><1><default><default>
  285.  
  286. ;----------------------------------------------------------------------------------
  287. ;SPI controller configuration
  288. ;----------------------------------------------------------------------------------
  289. [spi0]
  290. spi_used = 1
  291. spi_cs_bitmap = 1
  292. spi_mosi = port:PC00<3><default><default><default>
  293. spi_miso = port:PC01<3><default><default><default>
  294. spi_sclk = port:PC02<3><default><default><default>
  295. spi_cs0 = port:PC03<3><1><default><default>
  296.  
  297. [spi1]
  298. spi_used = 0
  299. spi_cs_bitmap = 1
  300. spi_cs0 = port:PA13<2><1><default><default>
  301. spi_sclk = port:PA14<2><default><default><default>
  302. spi_mosi = port:PA15<2><default><default><default>
  303. spi_miso = port:PA16<2><default><default><default>
  304.  
  305. ;----------------------------------------------------------------------------------
  306. ;SPI device configuration
  307. ;----------------------------------------------------------------------------------
  308. [spi_devices]
  309. spi_dev_num = 1
  310.  
  311. [spi_board0]
  312. modalias = "spidev"
  313. max_speed_hz = 33000000
  314. bus_num = 0
  315. chip_select = 0
  316. mode = 0
  317. full_duplex = 1
  318. manual_cs = 0
  319.  
  320. ;----------------------------------------------------------------------------------
  321. ;userspace gpio interface
  322. ; ** COMMENT THE PINS USED IN OTHER INTERFACES (I2C, SPI, 1-WIRE...)
  323. ;----------------------------------------------------------------------------------
  324. [gpio_para]
  325. gpio_used = 1
  326. ;gpio_num = 30
  327. ;gpio_pin_1 = port:PL10<1><default><default><1>
  328. ;gpio_pin_2 = port:PA15<1><default><default><0>
  329. ;gpio_pin_3 = port:PA12<1><default><default><0>
  330. ;gpio_pin_4 = port:PA11<1><default><default><0>
  331. ;gpio_pin_5 = port:PA06<1><default><default><0>
  332. ;gpio_pin_6 = port:PA13<1><default><default><0>
  333. ;gpio_pin_7 = port:PA14<1><default><default><0>
  334. ;gpio_pin_8 = port:PA01<1><default><default><0>
  335. ;gpio_pin_9 = port:PD14<1><default><default><0>
  336. ;gpio_pin_10 = port:PA00<1><default><default><0>
  337. ;gpio_pin_11 = port:PA03<1><default><default><0>
  338. ;gpio_pin_12 = port:PC04<1><default><default><0>
  339. ;gpio_pin_13 = port:PC07<1><default><default><0>
  340. ;gpio_pin_14 = port:PC00<1><default><default><0>
  341. ;gpio_pin_15 = port:PC01<1><default><default><0>
  342. ;gpio_pin_16 = port:PA02<1><default><default><0>
  343. ;gpio_pin_17 = port:PC02<1><default><default><0>
  344. ;gpio_pin_18 = port:PC03<1><default><default><0>
  345. ;gpio_pin_19 = port:PA21<1><default><default><0>
  346. ;gpio_pin_20 = port:PA19<1><default><default><0>
  347. ;gpio_pin_21 = port:PA18<1><default><default><0>
  348. ;gpio_pin_22 = port:PA07<1><default><default><0>
  349. ;gpio_pin_23 = port:PA08<1><default><default><0>
  350. ;gpio_pin_24 = port:PG08<1><default><default><0>
  351. ;gpio_pin_25 = port:PA09<1><default><default><0>
  352. ;gpio_pin_26 = port:PA10<1><default><default><0>
  353. ;gpio_pin_27 = port:PG09<1><default><default><0>
  354. ;gpio_pin_28 = port:PA20<1><default><default><0>
  355. ;gpio_pin_29 = port:PG06<1><default><default><0>
  356. ;gpio_pin_30 = port:PG07<1><default><default><0>
  357.  
  358. gpio_num = 19
  359. gpio_pin_1 = port:PL10<1><default><default><0>
  360. gpio_pin_2 = port:PA15<1><default><default><1>
  361. gpio_pin_3 = port:PA06<1><default><default><0>
  362. gpio_pin_4 = port:PA13<1><default><default><0>
  363. gpio_pin_5 = port:PA14<1><default><default><0>
  364. gpio_pin_6 = port:PD14<1><default><default><0>
  365. gpio_pin_7 = port:PA03<1><default><default><0>
  366. gpio_pin_8 = port:PC04<1><default><default><0>
  367. gpio_pin_9 = port:PC07<1><default><default><0>
  368. gpio_pin_10 = port:PC03<1><default><default><0>
  369. gpio_pin_11 = port:PA21<1><default><default><0>
  370. gpio_pin_12 = port:PA07<1><default><default><0>
  371. gpio_pin_13 = port:PA08<1><default><default><0>
  372. gpio_pin_14 = port:PG08<1><default><default><0>
  373. gpio_pin_15 = port:PA09<1><default><default><0>
  374. gpio_pin_16 = port:PA10<1><default><default><0>
  375. gpio_pin_17 = port:PG09<1><default><default><0>
  376. gpio_pin_18 = port:PG06<1><default><default><0>
  377. gpio_pin_19 = port:PG07<1><default><default><0>
  378.  
  379. [led_assign]
  380. normal_led = "gpio_pin_2"
  381. standby_led = "gpio_pin_1"
  382.  
  383. ;----------------------------------------------------------------------------------
  384. ;thermal configuration
  385. ;ths_trip_count : temperature trigger number
  386. ;ths_trip_0 : first temperature trigger
  387. ;ths_trip_1 : second temperature trigger
  388. ;ths_trip_2 : third temperature trigger, when upto this temperature, system shutdown
  389. ;ths_trip_0_min : first temperature trigger's min freq
  390. ;ths_trip_0_max : first temperature trigger's max freq
  391. ;ths_trip_1_min : second temperature trigger's min freq
  392. ;ths_trip_1_max : second temperature trigger's max freq
  393. ;----------------------------------------------------------------------------------
  394. [ths_para]
  395. ths_used = 1
  396. ths_trip1_count = 5
  397. ths_trip1_0 = 75
  398. ths_trip1_1 = 80
  399. ths_trip1_2 = 85
  400. ths_trip1_3 = 90
  401. ths_trip1_4 = 95
  402. ths_trip1_5 = 0
  403. ths_trip1_6 = 0
  404. ths_trip1_7 = 0
  405. ths_trip1_0_min = 0
  406. ths_trip1_0_max = 1
  407. ths_trip1_1_min = 1
  408. ths_trip1_1_max = 2
  409. ths_trip1_2_min = 2
  410. ths_trip1_2_max = 3
  411. ths_trip1_3_min = 3
  412. ths_trip1_3_max = 4
  413. ths_trip1_4_min = 4
  414. ths_trip1_4_max = 4
  415. ths_trip1_5_min = 0
  416. ths_trip1_5_max = 0
  417. ths_trip1_6_min = 0
  418. ths_trip1_6_max = 0
  419. ths_trip2_count = 1
  420. ths_trip2_0 = 95
  421. ;----------------------------------------------------------------------------------
  422. ;cooler_table cooler_count <=32
  423. ;----------------------------------------------------------------------------------
  424. [cooler_table]
  425. cooler_count = 5
  426. cooler0 = "1536000 4 4294967295 0"
  427. cooler1 = "1200000 4 4294967295 0"
  428. cooler2 = "1008000 4 4294967295 0"
  429. cooler3 = "816000 3 4294967295 0"
  430. cooler4 = "504000 1 4294967295 0"
  431.  
  432. [nand0_para]
  433. nand_support_2ch = 0
  434.  
  435. nand0_used = 0
  436. nand0_we = port:PC00<2><default><default><default>
  437. nand0_ale = port:PC01<2><default><default><default>
  438. nand0_cle = port:PC02<2><default><default><default>
  439. nand0_ce1 = port:PC03<2><default><default><default>
  440. nand0_ce0 = port:PC04<2><default><default><default>
  441. nand0_nre = port:PC05<2><default><default><default>
  442. nand0_rb0 = port:PC06<2><default><default><default>
  443. nand0_rb1 = port:PC07<2><default><default><default>
  444. nand0_d0 = port:PC08<2><default><default><default>
  445. nand0_d1 = port:PC09<2><default><default><default>
  446. nand0_d2 = port:PC10<2><default><default><default>
  447. nand0_d3 = port:PC11<2><default><default><default>
  448. nand0_d4 = port:PC12<2><default><default><default>
  449. nand0_d5 = port:PC13<2><default><default><default>
  450. nand0_d6 = port:PC14<2><default><default><default>
  451. nand0_d7 = port:PC15<2><default><default><default>
  452. nand0_ndqs = port:PC16<2><default><default><default>
  453.  
  454.  
  455. ;-----------------------------------------------------------------
  456. ;auto_hpd - 1:need hotplud for hdmi/tv; 0:don't hotplud for lcd
  457. ;output_type - 0:none; 1:lcd; 2:tv; 4:hdmi; 8:vga (as default config in homlet)
  458. ;hdmi_channel- the display channel for hdmi (as default config in homlet)
  459. ;cvbs_channel- the display channel for cvbs (as default config in homlet)
  460. ;hdmi_mode - as default config for output of hdmi in homlet
  461. ;cvbs_mode - as default config for output of tv in homlet. 11:PAL; 14:NTSC
  462. ;check the definition(of hdmi/cvbs_mode) of disp_tv_mode in sunxi_display2.h
  463. ;hdmi_mode_check - disable/enable the function of checking hdmi mode, 0 is disable, 1 is enable
  464. ;-----------------------------------------------------------------
  465. [boot_disp]
  466. advert_disp = 0
  467. auto_hpd = 1
  468. output_type = 4
  469. hdmi_channel = 0
  470. hdmi_mode = 4
  471. cvbs_channel = 1
  472. cvbs_mode = 11
  473. output_full = 1
  474. hdmi_mode_check = 1
  475.  
  476. ;----------------------------------------------------------------------------------
  477. ;disp init configuration
  478. ;
  479. ;disp_mode (0:screen0<screen0,fb0>; 1:screen1<screen1,fb0>)
  480. ;screenx_output_type (0:none; 1:lcd; 3:hdmi;)
  481. ;screenx_output_mode (used for hdmi output, 0:480i 1:576i 2:480p 3:576p 4:720p50)
  482. ; (5:720p60 6:1080i50 7:1080i60 8:1080p24 9:1080p50 10:1080p60)
  483. ;fbx format (0:ARGB 1:ABGR 2:RGBA 3:BGRA 5:RGB565 8:RGB888 12:ARGB4444 16:ARGB1555 18:RGBA5551)
  484. ;fbx_width,fbx_height (framebuffer horizontal/vertical pixels, fix to output resolution while equal 0)
  485. ;lcdx_backlight (lcd init backlight,the range:[0,256],default:197
  486. ;----------------------------------------------------------------------------------
  487. [disp_init]
  488. disp_init_enable = 1
  489. disp_mode = 0
  490.  
  491. screen0_output_type = 3
  492. screen0_output_mode = 10
  493.  
  494. screen1_output_type = 3
  495. screen1_output_mode = 10
  496.  
  497. fb0_format = 0
  498. fb0_width = 0
  499. fb0_height = 0
  500.  
  501. fb1_format = 0
  502. fb1_width = 0
  503. fb1_height = 0
  504.  
  505. fb0_framebuffer_num = 3
  506. sunxi_fb_mem_reserve = 32
  507.  
  508. ;----------------------------------------------------------------------------------
  509. ;hdmi configuration
  510. ;----------------------------------------------------------------------------------
  511. [hdmi_para]
  512. hdmi_used = 1
  513. hdmi_power = "vcc-hdmi-18"
  514. ;-------------------------------------
  515. ; set to 0 for hdmi->dvi compatibility
  516. ;-------------------------------------
  517. ;hdcp_enable = 0
  518. ;hdmi_cts_compatibility = 1
  519.  
  520. [tv_para]
  521. tv_used = 1
  522. tv_dac_used = 1
  523. tv_dac_src0 = 0
  524.  
  525. ;----------------------------------------------------------------------------------
  526. ;pwm config
  527. ;----------------------------------------------------------------------------------
  528. [pwm0_para]
  529. pwm_used = 0
  530. pwm_positive = port:PA05<3><0><default><default>
  531.  
  532. ;------------------------------------------------------------------------------;
  533. ; 10/100/100Mbps Ethernet MAC Controller Configure ;
  534. ;------------------------------------------------------------------------------;
  535. ; Options: ;
  536. ; gmac_used --- 0: not used, 1: external phy, 2: internal phy ;
  537. ; gmac_powerx -- A[:B] A: axp channel, B: voltage value ;
  538. ; If set gamc_phy to use internal PHY, do not config port ;
  539. ;------------------------------------------------------------------------------;
  540. ; MII RMII MII RMII MII RMII ;
  541. ; PD00 * PD06 * * PD12 * * ;
  542. ; PD01 * PD07 * PD13 * * ;
  543. ; PD02 * * PD08 * PD14 * ;
  544. ; PD03 * * PD09 * * PD15 * ;
  545. ; PD04 * PD10 * * PD16 * * ;
  546. ; PD05 * PD11 * * PD17 * * ;
  547. ;------------------------------------------------------------------------------;
  548. [gmac0]
  549. gmac_used = 2
  550. ;gmac_rxd3 = port:PD00<2><default><3><default>
  551. ;gmac_rxd2 = port:PD01<2><default><3><default>
  552. ;gmac_rxd1 = port:PD02<2><default><3><default>
  553. ;gmac_rxd0 = port:PD03<2><default><3><default>
  554. ;gmac_rxclk = port:PD04<2><default><3><default>
  555. ;gmac_rxdv = port:PD05<2><default><3><default>
  556. ;gmac_rxerr = port:PD06<2><default><3><default>
  557. ;gmac_txd3 = port:PD07<2><default><3><default>
  558. ;gmac_txd2 = port:PD08<2><default><3><default>
  559. ;gmac_txd1 = port:PD09<2><default><3><default>
  560. ;gmac_txd0 = port:PD10<2><default><3><default>
  561. ;gmac_crs = port:PD11<2><default><3><default>
  562. ;gmac_txclk = port:PD12<2><default><3><default>
  563. ;gmac_txen = port:PD13<2><default><3><default>
  564. ;gmac_txerr = port:PD14<2><default><3><default>
  565. ;gmac_col = port:PD15<2><default><3><default>
  566. ;gmac_mdc = port:PD16<2><default><3><default>
  567. ;gmac_mdio = port:PD17<2><default><3><default>
  568. gmac_power1 =
  569.  
  570. ;--------------------------------------------------------------------------------
  571. ;vip (video input port) configuration
  572. ;vip_used: 0:disable 1:enable
  573. ;vip_mode: 0:sample one interface to one buffer 1:sample two interface to one buffer
  574. ;vip_dev_qty: The quantity of devices linked to capture bus
  575. ;
  576. ;vip_define_sensor_list: If you want use sensor detect function, please set vip_define_sensor_list = 1, and
  577. ; verify that file /system/etc/hawkview/sensor_list_cfg.ini is properly configured!
  578. ;
  579. ;vip_dev(x)_pos: sensor position, "rear" or "front", if vip_define_sensor_list = 1,
  580. ;vip_dev(x)_pos must be configured!
  581. ;
  582. ;vip_dev(x)_isp_used 0:not use isp 1:use isp
  583. ;vip_dev(x)_fmt: 0:yuv 1:bayer raw rgb
  584. ;vip_dev(x)_stby_mode: 0:not shut down power at standby 1:shut down power at standby
  585. ;vip_dev(x)_vflip: flip in vertical direction 0:disable 1:enable
  586. ;vip_dev(x)_hflip: flip in horizontal direction 0:disable 1:enable
  587. ;vip_dev(x)_iovdd: camera module io power handle string, pmu power supply
  588. ;vip_dev(x)_iovdd_vol: camera module io power voltage, pmu power supply
  589. ;vip_dev(x)_avdd: camera module analog power handle string, pmu power supply
  590. ;vip_dev(x)_avdd_vol: camera module analog power voltage, pmu power supply
  591. ;vip_dev(x)_dvdd: camera module core power handle string, pmu power supply
  592. ;vip_dev(x)_dvdd_vol: camera module core power voltage, pmu power supply
  593. ;vip_dev(x)_afvdd: camera module vcm power handle string, pmu power supply
  594. ;vip_dev(x)_afvdd_vol: camera module vcm power voltage, pmu power supply
  595. ;x indicates the index of the devices which are linked to the same capture bus
  596. ;fill voltage in uV, e.g. iovdd = 2.8V, vip_devx_iovdd_vol = 2800000
  597. ;fill handle string as below:
  598. ;axp22_eldo3
  599. ;axp22_dldo4
  600. ;axp22_eldo2
  601. ;fill handle string "" when not using any pmu power supply
  602. ;--------------------------------------------------------------------------------
  603.  
  604. [csi0]
  605.  
  606. vip_used = 1
  607. vip_mode = 0
  608. vip_dev_qty = 1
  609. vip_define_sensor_list = 0
  610.  
  611. vip_csi_pck = port:PE00<2><default><default><default>
  612. vip_csi_mck = port:PE01<2><default><default><default>
  613. vip_csi_hsync = port:PE02<2><default><default><default>
  614. vip_csi_vsync = port:PE03<2><default><default><default>
  615. vip_csi_d0 = port:PE04<2><default><default><default>
  616. vip_csi_d1 = port:PE05<2><default><default><default>
  617. vip_csi_d2 = port:PE06<2><default><default><default>
  618. vip_csi_d3 = port:PE07<2><default><default><default>
  619. vip_csi_d4 = port:PE08<2><default><default><default>
  620. vip_csi_d5 = port:PE09<2><default><default><default>
  621. vip_csi_d6 = port:PE10<2><default><default><default>
  622. vip_csi_d7 = port:PE11<2><default><default><default>
  623. vip_csi_sck = port:PE12<2><default><default><default>
  624. vip_csi_sda = port:PE13<2><default><default><default>
  625.  
  626. vip_dev0_mname = "gc2035"
  627. vip_dev0_pos = "front"
  628. vip_dev0_lane = 1
  629. vip_dev0_twi_id = 2
  630. vip_dev0_twi_addr = 0x78
  631. vip_dev0_isp_used = 0
  632. vip_dev0_fmt = 0
  633. vip_dev0_stby_mode = 0
  634. vip_dev0_vflip = 1
  635. vip_dev0_hflip = 1
  636. vip_dev0_iovdd = ""
  637. vip_dev0_iovdd_vol = 2800000
  638. vip_dev0_avdd = ""
  639. vip_dev0_avdd_vol = 2800000
  640. vip_dev0_dvdd = ""
  641. vip_dev0_dvdd_vol = 1800000
  642. vip_dev0_afvdd = ""
  643. vip_dev0_afvdd_vol = 2800000
  644. vip_dev0_power_en = port:PA17<1><default><default><1>
  645. vip_dev0_reset = port:PE14<1><default><default><1>
  646. vip_dev0_pwdn = port:PE15<1><default><default><0>
  647. vip_dev0_flash_en =
  648. vip_dev0_flash_mode =
  649. vip_dev0_af_pwdn =
  650.  
  651. vip_dev0_act_used = 0
  652. vip_dev0_act_name = "ad5820_act"
  653. vip_dev0_act_slave = 0x18
  654.  
  655.  
  656. vip_dev1_mname = ""
  657. vip_dev1_pos = "rear"
  658. vip_dev1_lane = 1
  659. vip_dev1_twi_id = 0
  660. vip_dev1_twi_addr =
  661. vip_dev1_isp_used = 0
  662. vip_dev1_fmt = 1
  663. vip_dev1_stby_mode = 0
  664. vip_dev1_vflip = 0
  665. vip_dev1_hflip = 0
  666. vip_dev1_iovdd = ""
  667. vip_dev1_iovdd_vol = 2800000
  668. vip_dev1_avdd = ""
  669. vip_dev1_avdd_vol = 2800000
  670. vip_dev1_dvdd = ""
  671. vip_dev1_dvdd_vol = 1500000
  672. vip_dev1_afvdd = ""
  673. vip_dev1_afvdd_vol = 2800000
  674. vip_dev1_power_en =
  675. vip_dev1_reset =
  676. vip_dev1_pwdn =
  677. vip_dev1_flash_en =
  678. vip_dev1_flash_mode =
  679. vip_dev1_af_pwdn =
  680.  
  681.  
  682. ;--------------------------------------------------------------------------------
  683. ;tv configuration
  684. ;
  685. ;--------------------------------------------------------------------------------
  686. [tvout_para]
  687. tvout_used =
  688. tvout_channel_num =
  689. tv_en =
  690.  
  691. [tvin_para]
  692. tvin_used =
  693. tvin_channel_num =
  694.  
  695. ;----------------------------------------------------------------------------------
  696. ;DE-Interlace configuration
  697. ;----------------------------------------------------------------------------------
  698. [di_para]
  699. di_used = 1
  700.  
  701. ;--------------------------------------------------------------------------------
  702. ; SDMMC PINS MAPPING |
  703. ; ------------------------------------------------------------------------------|
  704. ; Config Guide |
  705. ; sdc_used: 1-enable card, 0-disable card |
  706. ; sdc_detmode: card detect mode |
  707. ; 1-detect card by gpio polling |
  708. ; 2-detect card by gpio irq(must use IO with irq function) |
  709. ; 3-no detect, always in for boot card |
  710. ; 4-manually insert and remove by /proc/driver/sunxi-mmc.x/insert|
  711. ; sdc_buswidth: card bus width, 1-1bit, 4-4bit, 8-8bit |
  712. ; sdc_use_wp: 1-with write protect IO, 0-no write protect IO |
  713. ; sdc_isio: for sdio card |
  714. ; sdc_regulator: power control.if card supports UHS-I/DDR and HS200 timing for|
  715. ; SD3.0 or eMMC4.5, regulator must be configured. the value is |
  716. ; the ldo name of AXP221, eg: sdc_regulator = "axp22_eldo2" |
  717. ; other: GPIO Mapping configuration |
  718. ; ------------------------------------------------------------------------------|
  719. ; Note: |
  720. ; 1 if detmode=2, sdc_det's config=6 |
  721. ; else if detmode=1, sdc_det's config=0 |
  722. ; else sdc_det IO is not necessary |
  723. ; 2 if the customer wants to support UHS-I and HS200 features, he must provide|
  724. ; an independent power supply for the card. This is only used in platforms |
  725. ; that supports SD3.0 cards and eMMC4.4+ flashes |
  726. ;--------------------------------------------------------------------------------
  727. [mmc0_para]
  728. sdc_used = 1
  729. sdc_detmode = 1
  730. sdc_buswidth = 4
  731. sdc_clk = port:PF02<2><1><2><default>
  732. sdc_cmd = port:PF03<2><1><2><default>
  733. sdc_d0 = port:PF01<2><1><2><default>
  734. sdc_d1 = port:PF00<2><1><2><default>
  735. sdc_d2 = port:PF05<2><1><2><default>
  736. sdc_d3 = port:PF04<2><1><2><default>
  737. sdc_det = port:PF06<0><1><2><default>
  738. sdc_use_wp = 0
  739. sdc_wp =
  740. sdc_isio = 0
  741. sdc_regulator = "none"
  742. sdc_power_supply = "none"
  743.  
  744. [mmc1_para]
  745. sdc_used = 1
  746. sdc_detmode = 4
  747. sdc_buswidth = 4
  748. sdc_clk = port:PG00<2><1><3><default>
  749. sdc_cmd = port:PG01<2><1><3><default>
  750. sdc_d0 = port:PG02<2><1><3><default>
  751. sdc_d1 = port:PG03<2><1><3><default>
  752. sdc_d2 = port:PG04<2><1><3><default>
  753. sdc_d3 = port:PG05<2><1><3><default>
  754. sdc_det =
  755. sdc_use_wp = 0
  756. sdc_wp =
  757. sdc_isio = 1
  758. sdc_regulator = "none"
  759. sdc_power_supply = "none"
  760. sdc_2xmode = 1
  761. sdc_ddrmode = 1
  762.  
  763. [mmc2_para]
  764. sdc_used = 0
  765. sdc_detmode = 3
  766. sdc_buswidth = 8
  767. sdc_clk = port:PC05<3><1><2><default>
  768. sdc_cmd = port:PC06<3><1><2><default>
  769. sdc_d0 = port:PC08<3><1><2><default>
  770. sdc_d1 = port:PC09<3><1><2><default>
  771. sdc_d2 = port:PC10<3><1><2><default>
  772. sdc_d3 = port:PC11<3><1><2><default>
  773. sdc_d4 = port:PC12<3><1><2><default>
  774. sdc_d5 = port:PC13<3><1><2><default>
  775. sdc_d6 = port:PC14<3><1><2><default>
  776. sdc_d7 = port:PC15<3><1><2><default>
  777. emmc_rst = port:PC16<3><1><2><default>
  778. sdc_det =
  779. sdc_use_wp = 0
  780. sdc_wp =
  781. sdc_isio = 0
  782. sdc_regulator = "none"
  783. sdc_power_supply = "none"
  784. sdc_2xmode = 1
  785. sdc_ddrmode = 1
  786.  
  787. ; ------------------------------------------------------------------------------|
  788. ; sim card configuration
  789. ;--------------------------------------------------------------------------------
  790. [smc_para]
  791. smc_used = 0
  792. smc_rst = port:PA09<2><default><default><default>
  793. smc_vppen = port:PA20<3><default><default><default>
  794. smc_vppp = port:PA21<3><default><default><default>
  795. smc_det = port:PA10<2><default><default><default>
  796. smc_vccen = port:PA06<2><default><default><default>
  797. smc_sck = port:PA07<2><default><default><default>
  798. smc_sda = port:PA08<2><default><default><default>
  799.  
  800.  
  801. ;--------------------------------
  802. ; [usbc0]: Controller 0 configuration.
  803. ; usb used: USB enable flag. Set, indicating that the system USB module is available, is set to 0, it means that the system USB is disabled.
  804. ; usb_port_type: USB port usage. 0: device only; 1: host only; 2: OTG
  805. ; usb_detect_type: USB port of checking. 0: not detected; 1: vbus / id checks; 2: id / dpdm check
  806. ; usb_id_gpio: USB ID pin pin configuration. For details, please refer gpio configuration instructions.
  807. ; usb_det_vbus_gpio: USB DET_VBUS pin pin configuration. For details, please refer gpio configuration instructions.
  808. ; usb_drv_vbus_gpio: USB DRY_VBUS pin pin configuration. For details, please refer gpio configuration instructions.
  809. ; usb_det_vbus_gpio: "axp_ctrl", represents axp offer
  810. ; usb_restrict_gpio: usb limiting control pin
  811. ; usb_restric_flag: usb limiting standard set
  812. ;--------------------------------
  813. ;--------------------------------
  814. ;--- USB0控制标志
  815. ;--------------------------------
  816. [usbc0]
  817. usb_used = 1
  818. ;usb_port_type = 2
  819. usb_port_type = 1
  820. ;usb_detect_type = 1
  821. usb_detect_type = 0
  822. usb_id_gpio = port:PG12<0><1><default><default>
  823. usb_det_vbus_gpio = port:PG12<0><1><default><default>
  824. usb_drv_vbus_gpio = port:PL02<1><0><default><0>
  825. usb_host_init_state = 1
  826. usb_restrict_gpio =
  827. usb_restric_flag = 0
  828. usb_restric_voltage = 3550000
  829. usb_restric_capacity= 5
  830. usb_regulator_io = "nocare"
  831. usb_regulator_vol = 0
  832. usb_not_suspend = 0
  833.  
  834. ;--------------------------------
  835. ;--- USB1控制标志
  836. ;--------------------------------
  837. [usbc1]
  838. usb_used = 1
  839. usb_drv_vbus_gpio =
  840. usb_restrict_gpio =
  841. usb_host_init_state = 1
  842. usb_restric_flag = 0
  843. usb_regulator_io = "nocare"
  844. usb_regulator_vol = 0
  845. usb_not_suspend = 0
  846.  
  847. ;--------------------------------
  848. ;--- USB2控制标志
  849. ;--------------------------------
  850. [usbc2]
  851. usb_used = 1
  852. usb_drv_vbus_gpio =
  853. usb_restrict_gpio =
  854. usb_host_init_state = 1
  855. usb_restric_flag = 0
  856. usb_regulator_io = "nocare"
  857. usb_regulator_vol = 0
  858. usb_not_suspend = 0
  859.  
  860. ;--------------------------------
  861. ;--- USB3控制标志
  862. ;--------------------------------
  863. [usbc3]
  864. usb_used = 1
  865. usb_drv_vbus_gpio =
  866. usb_restrict_gpio =
  867. usb_host_init_state = 1
  868. usb_restric_flag = 0
  869. usb_regulator_io = "nocare"
  870. usb_regulator_vol = 0
  871. usb_not_suspend = 0
  872.  
  873. ;--------------------------------
  874. ;--- USB Device
  875. ;--------------------------------
  876. [usb_feature]
  877. vendor_id = 0x18D1
  878. mass_storage_id = 0x0001
  879. adb_id = 0x0002
  880.  
  881. manufacturer_name = "USB Developer"
  882. product_name = "Android"
  883. serial_number = "20080411"
  884.  
  885. [msc_feature]
  886. vendor_name = "USB 2.0"
  887. product_name = "USB Flash Driver"
  888. release = 100
  889. luns = 3
  890.  
  891. [serial_feature]
  892. serial_unique = 0
  893.  
  894.  
  895. ;--------------------------------------------------------------------------------
  896. ;wifi/bt/fm/gps/nfc modules configuration
  897. ;module_num:
  898. ; 0- none
  899. ; 1- rtl8188eu(wifi)
  900. ; 2- rtl8723bs(wifi+bt)
  901. ; 3- ap6181(wifi)
  902. ; 4- ap6210(wifi+bt)
  903. ; 5- ap6330(wifi+bt)
  904. ; 6- ap6335(wifi)
  905. ; 7- rtl8189etv(wifi)
  906. ;module_power0: axp used by module, "axp22_dldo1" - use dldo1, not use keep it empty
  907. ;module_power0_vol: power0 voltage, mv;
  908. ;chip_en: enable chip io
  909. ;lpo_use_apclk: ""- not use, "losc_out"- a23/33/H3, "ac10032k1"、"ac10032k2"、"ac10032k3"- a80
  910. ;--------------------------------------------------------------------------------
  911. [module_para]
  912. module_num = 7
  913. module_power0 = "vcc-wifi-33"
  914. module_power0_vol = 0
  915. module_power1 =
  916. module_power1_vol =
  917. module_power2 =
  918. module_power2_vol =
  919. module_power3 =
  920. module_power3_vol =
  921. chip_en =
  922. lpo_use_apclk =
  923.  
  924. ;--------------------------------------------------------------------------------
  925. ;wifi configuration
  926. ;wifi_sdc_id: 0- SDC0, 1- SDC1, 2- SDC2, 3- SDC3
  927. ;wifi_usbc_id: 0- USB0, 1- USB1, 2- USB2
  928. ;wifi_usbc_type: 1- EHCI(speed 2.0), 2- OHCI(speed 1.0)
  929. ;wl_reg_on: wifi function enable pin
  930. ;wl_host_wake: wlan device wake-up host pin
  931. ;wl_host_wake_invert: whether wl_host_wake use inverter between ap and module
  932. ; 0: not used, 1: used
  933. ;--------------------------------------------------------------------------------
  934. [wifi_para]
  935. wifi_used = 0
  936. wifi_sdc_id = 1
  937. wifi_usbc_id = 5
  938. wifi_usbc_type = 1
  939. wl_reg_on = port:PL07<1><default><default><0>
  940. wl_host_wake = port:PG10<0><default><default><0>
  941. wl_host_wake_invert = 0
  942.  
  943. ;--------------------------------------------------------------------------------
  944. ;bluetooth configuration
  945. ;bt_used: 0- no used, 1- used
  946. ;bt_uard_id: 0- uart0, 1- uart1, 2- uart2
  947. ;bt_rst_n: bt function enable io
  948. ;bt_wake: host wake-up bluetooth device
  949. ;bt_host_wake: bt device wake-up host
  950. ;bt_host_wake_invert: whether bt_host_wake use inverter between ap and module
  951. ; 0: not used, 1: used
  952. ;--------------------------------------------------------------------------------
  953. [bt_para]
  954. bt_used = 0
  955. bt_uart_id = 1
  956. bt_rst_n =
  957. bt_wake =
  958. bt_host_wake =
  959. bt_host_wake_invert = 0
  960.  
  961. ;--------------------------------------------------------------------------------
  962. ;daudio_master:1: SND_SOC_DAIFMT_CBM_CFM(codec clk & FRM master) use
  963. ; 2: SND_SOC_DAIFMT_CBS_CFM(codec clk slave & FRM master) not use
  964. ; 3: SND_SOC_DAIFMT_CBM_CFS(codec clk master & frame slave) not use
  965. ; 4: SND_SOC_DAIFMT_CBS_CFS(codec clk & FRM slave) use
  966. ;daudio_select:0 is pcm.1 is i2s
  967. ;audio_format: 1:SND_SOC_DAIFMT_I2S(standard i2s format). use
  968. ; 2:SND_SOC_DAIFMT_RIGHT_J(right justfied format).
  969. ; 3:SND_SOC_DAIFMT_LEFT_J(left justfied format)
  970. ; 4:SND_SOC_DAIFMT_DSP_A(pcm. MSB is available on 2nd BCLK rising edge after LRC rising edge). use
  971. ; 5:SND_SOC_DAIFMT_DSP_B(pcm. MSB is available on 1nd BCLK rising edge after LRC rising edge)
  972. ;signal_inversion:1:SND_SOC_DAIFMT_NB_NF(normal bit clock + frame) use
  973. ; 2:SND_SOC_DAIFMT_NB_IF(normal BCLK + inv FRM)
  974. ; 3:SND_SOC_DAIFMT_IB_NF(invert BCLK + nor FRM) use
  975. ; 4:SND_SOC_DAIFMT_IB_IF(invert BCLK + FRM)
  976. ;over_sample_rate: support 128fs/192fs/256fs/384fs/512fs/768fs
  977. ;sample_resolution :16bits/20bits/24bits
  978. ;word_select_size :16bits/20bits/24bits/32bits
  979. ;pcm_sync_period :16/32/64/128/256
  980. ;msb_lsb_first :0: msb first; 1: lsb first
  981. ;sign_extend :0: zero pending; 1: sign extend
  982. ;slot_index :slot index: 0: the 1st slot - 3: the 4th slot
  983. ;slot_width :8 bit width / 16 bit width
  984. ;frame_width :0: long frame = 2 clock width; 1: short frame
  985. ;tx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
  986. ;rx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
  987. ;--------------------------------------------------------------------------------
  988. [pcm0]
  989. daudio_used = 0
  990. daudio_master = 4
  991. daudio_select = 1
  992. audio_format = 1
  993. signal_inversion = 1
  994. mclk_fs = 128
  995. sample_resolution = 16
  996. slot_width_select = 32
  997. ;pcm_sync_period = 256
  998. pcm_lrck_period = 32
  999. pcm_lrckr_period = 1
  1000. msb_lsb_first = 0
  1001. sign_extend = 0
  1002. slot_index = 0
  1003. slot_width = 32
  1004. frame_width = 0
  1005. tx_data_mode = 0
  1006. rx_data_mode = 0
  1007. i2s_mclk = port:PA18<2><1><default><default>
  1008. i2s_bclk = port:PA19<2><1><default><default>
  1009. i2s_dout0 = port:PA20<2><1><default><default>
  1010. i2s_din = port:PA21<2><1><default><default>
  1011.  
  1012.  
  1013. [pcm1]
  1014. daudio_used = 0
  1015. daudio_master = 4
  1016. daudio_select = 1
  1017. audio_format = 1
  1018. signal_inversion = 1
  1019. mclk_fs = 128
  1020. sample_resolution = 16
  1021. slot_width_select = 32
  1022. ;pcm_sync_period = 256
  1023. pcm_lrck_period = 32
  1024. pcm_lrckr_period = 1
  1025. msb_lsb_first = 0
  1026. sign_extend = 0
  1027. slot_index = 0
  1028. slot_width = 32
  1029. frame_width = 0
  1030. tx_data_mode = 0
  1031. rx_data_mode = 0
  1032. i2s_mclk = port:PG10<2><1><default><default>
  1033. i2s_bclk = port:PG11<2><1><default><default>
  1034. i2s_dout0 = port:PG12<2><1><default><default>
  1035. i2s_din = port:PG13<2><1><default><default>
  1036.  
  1037.  
  1038. [audio0]
  1039. audio_used = 1
  1040. lineout_vol = 0x1f
  1041. cap_vol = 0x5
  1042. audio_hp_ldo = "none"
  1043. adcagc_used = 0
  1044. adcdrc_used = 0
  1045. dacdrc_used = 0
  1046. adchpf_used = 0
  1047. dachpf_used = 0
  1048. audio_pa_ctrl = port:PA16<1><default><default><0>
  1049.  
  1050. [spdif0]
  1051. spdif_used = 0
  1052. spdif_dout = port:PA17<2><1><default><default>
  1053.  
  1054. [audiohub]
  1055. hub_used = 0
  1056. codec_used = 1
  1057. spdif_used = 1
  1058. hdmi_used = 1
  1059.  
  1060. ;----------------------------------------------------------------------------------
  1061. ;ir rx --- infra remote configuration
  1062. ;----------------------------------------------------------------------------------
  1063. [s_cir0]
  1064. ir_used = 1
  1065. ir_rx = port:PL11<2><1><default><default>
  1066. ir_power_key_code0 = 0x57
  1067. ir_addr_code0 = 0x9f00
  1068. ir_power_key_code1 = 0x1a
  1069. ir_addr_code1 = 0xfb04
  1070. ir_power_key_code2 = 0x14
  1071. ir_addr_code2 = 0x7F80
  1072. ir_power_key_code3 = 0x15
  1073. ir_addr_code3 = 0x7F80
  1074. ir_power_key_code4 = 0x0b
  1075. ir_addr_code4 = 0xF708
  1076. ir_power_key_code5 = 0x03
  1077. ir_addr_code5 = 0x00EF
  1078. ir_power_key_code6 = 0x9f
  1079. ir_addr_code6 = 0x4CB3
  1080. ir_power_key_code7 = 0x0a
  1081. ir_addr_code7 = 0x7748
  1082. ir_power_key_code8 = 0x45
  1083. ir_addr_code8 = 0xbd02
  1084. ir_power_key_code9 = 0x4d
  1085. ir_addr_code9 = 0xde21
  1086. ir_power_key_code10 = 0x18
  1087. ir_addr_code10 = 0xfe01
  1088. ir_power_key_code11 = 0x57
  1089. ir_addr_code11 = 0xff00
  1090. ir_power_key_code12 = 0x4d
  1091. ir_addr_code12 = 0xff40
  1092.  
  1093.  
  1094. ;----------------------------------------------------------------------------------
  1095. ;ir tx--- infra remote configuration
  1096. ;----------------------------------------------------------------------------------
  1097. [cir]
  1098. ir_used = 1
  1099. ir_tx = port:PH07<2><default><default><default>
  1100.  
  1101.  
  1102. ;----------------------------------------------------------------------------------
  1103. ; dvfs voltage-frequency table configuration
  1104. ;
  1105. ; pmuic_type:0:none, 1:gpio, 2:i2c
  1106. ; pmu_gpio0: gpio config.
  1107. ; pmu_levelx: 0~9999: voltage(mV), 10000~90000:gpio0 state. voltage form high to low.
  1108. ;
  1109. ; extremity_freq(Hz): cpu extremity frequency when run benckmark or demo apk
  1110. ; 1536MHz@1500mV with radiator, 1296MHz@1340mV without radiator
  1111. ; max_freq: cpu maximum frequency, based on Hz, can not be more than 1200MHz
  1112. ; min_freq: cpu minimum frequency, based on Hz, can not be less than 60MHz
  1113. ;
  1114. ; LV_count: count of LV_freq/LV_volt, must be < 16
  1115. ;
  1116. ; LV1: core vdd is 1.50v if cpu frequency is (1296Mhz, 1536Mhz]
  1117. ; LV2: core vdd is 1.34v if cpu frequency is (1200Mhz, 1296Mhz]
  1118. ; LV3: core vdd is 1.32v if cpu frequency is (1008Mhz, 1200Mhz]
  1119. ; LV4: core vdd is 1.20v if cpu frequency is (816Mhz, 1008Mhz]
  1120. ; LV5: core vdd is 1.10v if cpu frequency is (648Mhz, 816Mhz]
  1121. ; LV6: core vdd is 1.04v if cpu frequency is (0Mhz, 648Mhz]
  1122. ; LV7: core vdd is 1.04v if cpu frequency is (0Mhz, 648Mhz]
  1123. ; LV8: core vdd is 1.04v if cpu frequency is (0Mhz, 648Mhz]
  1124. ;
  1125. ;----------------------------------------------------------------------------------
  1126. [dvfs_table]
  1127. pmuic_type = 2
  1128. pmu_gpio0 = port:PL06<1><1><2><1>
  1129. pmu_level0 = 11300
  1130. pmu_level1 = 01100
  1131.  
  1132. extremity_freq = 1536000000
  1133. max_freq = 1200000000
  1134. min_freq = 60000000
  1135. LV_count = 8
  1136. LV1_freq = 1536000000
  1137. LV1_volt = 1500
  1138. LV2_freq = 1248000000
  1139. LV2_volt = 1260
  1140. LV3_freq = 1200000000
  1141. LV3_volt = 1240
  1142. LV4_freq = 1008000000
  1143. LV4_volt = 1140
  1144. LV5_freq = 816000000
  1145. LV5_volt = 1040
  1146. LV6_freq = 312000000
  1147. LV6_volt = 960
  1148. LV7_freq = 0
  1149. LV7_volt = 960
  1150. LV8_freq = 0
  1151. LV8_volt = 960
  1152.  
  1153. [gpu_dvfs_table]
  1154.  
  1155. G_LV_count = 3
  1156.  
  1157. G_LV0_freq = 312000000
  1158. G_LV0_volt = 1200000
  1159.  
  1160. G_LV1_freq = 384000000
  1161. G_LV1_volt = 1200000
  1162.  
  1163. G_LV2_freq = 456000000
  1164. G_LV2_volt = 1200000
  1165.  
  1166.  
  1167. ;----------------------------------------------------------------------------------
  1168. ;virtual device
  1169. ;virtual device for pinctrl testing
  1170. ;device have pin PA1 PA2
  1171. ;----------------------------------------------------------------------------------
  1172. [Vdevice]
  1173. Vdevice_used = 0
  1174. Vdevice_0 = port:PH10<5><1><2><default>
  1175. Vdevice_1 = port:PH11<5><1><2><default>
  1176.  
  1177. ;----------------------------------------------------------------------------------
  1178. ;s_uart0 config parameters
  1179. ;s_uart_used --s_uart0 whether used for arisc debugging
  1180. ;----------------------------------------------------------------------------------
  1181. [s_uart0]
  1182. s_uart_used = 0
  1183. s_uart_tx = port:PL02<2><default><default><default>
  1184. s_uart_rx = port:PL03<2><default><default><default>
  1185.  
  1186. ;----------------------------------------------------------------------------------
  1187. ;s_rsb0 config parameters
  1188. ;s_rsb_used --s_rsb0 whether used for arisc
  1189. ;----------------------------------------------------------------------------------
  1190. [s_rsb0]
  1191. s_rsb_used = 1
  1192. s_rsb_sck = port:PL00<2><1><2><default>
  1193. s_rsb_sda = port:PL01<2><1><2><default>
  1194.  
  1195. ;----------------------------------------------------------------------------------
  1196. ;s_jtag0 config parameters
  1197. ;s_jtag0_used --s_jtag0 whether used for arisc
  1198. ;
  1199. ;----------------------------------------------------------------------------------
  1200. [s_jtag0]
  1201. s_jtag_used = 0
  1202. s_jtag_tms = port:PL04<2><1><2><default>
  1203. s_jtag_tck = port:PL05<2><1><2><default>
  1204. s_jtag_tdo = port:PL06<2><1><2><default>
  1205. s_jtag_tdi = port:PL07<2><1><2><default>
  1206.  
  1207. ;----------------------------------------------------------------------------------
  1208. ;s_powchk cpus power check
  1209. ;s_powchk_used --power check whether used for arisc in super standby
  1210. ; bit31:enable power updat, bit1:wakeup when power state exception
  1211. ; bit0:wakeup when power consumption exception
  1212. ;s_power_reg the expected regs stand for power on/off state
  1213. ;s_system_power the limit maxmum power consumption when super standby (unit: mw)
  1214. ;
  1215. ;----------------------------------------------------------------------------------
  1216. [s_powchk]
  1217. s_powchk_used = 0x80000000
  1218. s_power_reg = 0x00000000
  1219. s_system_power = 50
  1220.  
  1221. ;----------------------------------------------------------------------------------
  1222. ;scr configuration
  1223. ;----------------------------------------------------------------------------------
  1224. [sim0]
  1225. scr_used = 0
  1226. scr_vccen = port:PA06<2><default><default><default>
  1227. scr_slk = port:PA07<2><default><default><default>
  1228. scr_sda = port:PA08<2><default><default><default>
  1229. scr_rst = port:PA09<2><default><default><default>
  1230. scr_det = port:PA10<2><default><default><default>
  1231.  
  1232.  
  1233. ;--------------------------------------------------------------------------------
  1234. ;tsc configuration
  1235. ;--------------------------------------------------------------------------------
  1236. [ts0]
  1237. tsc_used = 0
  1238. tsc_clk = port:PE00<3><default><default><default>
  1239. tsc_err = port:PE01<3><default><default><default>
  1240. tsc_sync = port:PE02<3><default><default><default>
  1241. tsc_dvld = port:PE03<3><default><default><default>
  1242. tsc_d0 = port:PE04<3><default><default><default>
  1243. tsc_d1 = port:PE05<3><default><default><default>
  1244. tsc_d2 = port:PE06<3><default><default><default>
  1245. tsc_d3 = port:PE07<3><default><default><default>
  1246. tsc_d4 = port:PE08<3><default><default><default>
  1247. tsc_d5 = port:PE09<3><default><default><default>
  1248. tsc_d6 = port:PE10<3><default><default><default>
  1249. tsc_d7 = port:PE11<3><default><default><default>
  1250.  
  1251. ;--------------------------------------------------------------------------------
  1252. ;gpio key
  1253. ;--------------------------------------------------------------------------------
  1254. [gpio_power_key]
  1255. key_used = 1
  1256. key_io = port:PL03<6><default><default><0>
  1257.  
  1258. ;----------------------------------------------------------------------------------
  1259. ; key para
  1260. ;
  1261. ; key_used --0:not used, 1:used
  1262. ; key_cnt --how many key button attach to keyadc.
  1263. ; key*_vol --the threshold of input voltage of key.
  1264. ;
  1265. ; For example: if key2_vol < $(keyadc value) < key3_vol, then key3 be reported.
  1266. ;----------------------------------------------------------------------------------
  1267. [key_para]
  1268. key_used = 0
  1269. key_cnt = 5
  1270. key1_vol = 222
  1271. key2_vol = 444
  1272. key3_vol = 666
  1273. key4_vol = 857
  1274. key5_vol = 2000
  1275.  
  1276.  
  1277. ;----------------------------------------------------------------------------------
  1278. ;display seven segment para
  1279. ;----------------------------------------------------------------------------------
  1280. [d7s_para]
  1281. d7s_used = 0
  1282. din_gpio = port:PD00<1><default><default><1>
  1283. clk_gpio = port:PD01<1><default><default><1>
  1284. stb_gpio = port:PD02<1><default><default><1>
  1285.  
  1286.  
  1287. ;----------------------------------------------------------------------------------
  1288. ;mali parameters
  1289. ;----------------------------------------------------------------------------------
  1290. [mali_para]
  1291. mali_used = 1
  1292. mali_clkdiv = 1
  1293. mali_extreme_freq = 600
  1294. mali_extreme_vol = 1400
  1295.  
  1296.  
  1297. ;----------------------------------------------------------------------------------
  1298. ;1wire parameters (default - PA20)
  1299. ;----------------------------------------------------------------------------------
  1300. [w1_para]
  1301. w1_used = 1
  1302. gpio = 20
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!