Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.02.17 13:55:39 =~=~=~=~=~=~=~=~=~=~=~=
- =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.02.17 14:03:06 =~=~=~=~=~=~=~=~=~=~=~=
- Please press Enter to activate this console.
- Please press Enter to activate this console.
- [ 894.650894] reboot: Restarting system
- U-Boot 1.1.7 (Dec 13 2011 - 13:49:42)
- Board: Ralink APSoC DRAM: 32 MB
- relocate_code Pointer at: 81fb4000
- ******************************
- Software System Reset Occurred
- ******************************
- spi_wait_nsec: 42
- spi device id: 7f 9d 46 7f 9d (9d467f9d)
- Warning: un-recognized chip ID, please update bootloader!
- raspi_read: from:30000 len:1000
- .*** Warning - bad CRC, using default environment
- ============================================
- Ralink UBoot Version: 3.6.0.0
- --------------------------------------------
- ASIC 5350_MP (Port5<->None)
- DRAM_CONF_FROM: Boot-Strapping
- DRAM_TYPE: SDRAM
- DRAM_SIZE: 256 Mbits
- DRAM_WIDTH: 16 bits
- DRAM_TOTAL_WIDTH: 16 bits
- TOTAL_MEMORY_SIZE: 32 MBytes
- Flash component: SPI Flash
- Date:Dec 13 2011 Time:13:49:42
- ============================================
- icache: sets:256, ways:4, linesz:32 ,total:32768
- dcache: sets:128, ways:4, linesz:32 ,total:16384
- ##### The CPU freq = 360 MHZ ####
- estimate memory size =32 Mbytes
- raspi_read: from:40028 len:6
- .
- raspi_read: from:0 len:30004
- ....*************Is_update = 0 plat = 1**************
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 7: Load Boot Loader code then write to Flash via Serial.
- 9: Load Boot Loader code then write to Flash via TFTP.
- 1 0
- 3: System Boot system code via Flash.
- ## Booting image at bc050000 ...
- raspi_read: from:50000 len:40
- . Image Name: MIPS LEDE Linux-4.4.61
- Created: 2017-04-17 16:15:53 UTC
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 1158946 Bytes = 1.1 MB
- Load Address: 80000000
- Entry Point: 80000000
- raspi_read: from:50040 len:11af22
- .................. Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80000000) ...
- ## Giving linux memsize in MB, 32
- Starting kernel ...
- [ 0.000000] Linux version 4.4.61 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3102-0224e32) ) #0 Sat Apr 15 16:13:45 2017
- [ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
- [ 0.000000] MIPS: machine is A5-V11
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 02000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
- [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
- [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
- [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Writing ErrCtl register=00069b50
- [ 0.000000] Readback ErrCtl register=00069b50
- [ 0.000000] Memory: 28612K/32768K available (2888K kernel code, 136K rwdata, 356K rodata, 196K init, 196K bss, 4156K reserved, 0K cma-reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:256
- [ 0.000000] CPU Clock: 360MHz
- [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
- [ 0.000000] systick: running - mult: 214748, shift: 32
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 10618113593 ns
- [ 0.000015] sched_clock: 32 bits at 180MHz, resolution 5ns, wraps every 11930464253ns
- [ 0.015682] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
- [ 0.090885] pid_max: default: 32768 minimum: 301
- [ 0.100300] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.113377] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.136776] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.156352] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 0.168557] pinctrl core: initialized pinctrl subsystem
- [ 0.181389] NET: Registered protocol family 16
- [ 0.200334] Can't analyze schedule() prologue at 8000ac9c
- [ 0.242016] rt2880_gpio 10000600.gpio: registering 22 gpios
- [ 0.253145] rt2880_gpio 10000600.gpio: registering 22 irq handlers
- [ 0.265840] rt2880_gpio 10000660.gpio: registering 6 gpios
- [ 0.276779] rt2880_gpio 10000660.gpio: registering 6 irq handlers
- [ 0.291439] clocksource: Switched to clocksource MIPS
- [ 0.303713] NET: Registered protocol family 2
- [ 0.314348] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.328238] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.340820] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.353680] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.365297] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.378265] NET: Registered protocol family 1
- [ 0.397344] rt-timer 10000100.timer: maximum frequency is 3662Hz
- [ 0.410813] Crashlog allocated RAM at address 0x1f00000
- [ 0.456873] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.468466] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.494140] io scheduler noop registered
- [ 0.501916] io scheduler deadline registered (default)
- [ 0.512472] ralink-usb-phy usbphy: invalid resource
- [ 0.523565] gpio-export gpio_export: 2 gpio(s) exported
- [ 0.534371] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 0.553962] console [ttyS0] disabled
- [ 0.561010] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
- [ 0.580836] console [ttyS0] enabled
- [ 0.580836] console [ttyS0] enabled
- [ 0.594607] bootconsole [early0] disabled
- [ 0.594607] bootconsole [early0] disabled
- [ 0.626196] spi spi0.0: force spi mode3
- [ 0.634854] m25p80 spi0.0: pm25lq032 (4096 Kbytes)
- [ 0.644602] 4 ofpart partitions found on MTD device spi0.0
- [ 0.655586] Creating 4 MTD partitions on "spi0.0":
- [ 0.665198] 0x000000000000-0x000000030000 : "u-boot"
- [ 0.678826] 0x000000030000-0x000000040000 : "u-boot-env"
- [ 0.693566] 0x000000040000-0x000000050000 : "factory"
- [ 0.707661] 0x000000050000-0x000000400000 : "firmware"
- [ 1.014205] 2 uimage-fw partitions found on MTD device firmware
- [ 1.026141] 0x000000050000-0x00000016af62 : "kernel"
- [ 1.039347] 0x00000016af62-0x000000400000 : "rootfs"
- [ 1.053284] mtd: device 5 (rootfs) set to be root filesystem
- [ 1.064901] 1 squashfs-split partitions found on MTD device rootfs
- [ 1.077323] 0x0000003a3000-0x000000400000 : "rootfs_data"
- [ 1.098410] rt3050-esw 10110000.esw: link changed 0x00
- [ 1.112433] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
- [ 1.130075] rt2880_wdt 10000120.watchdog: Initialized
- [ 1.142986] NET: Registered protocol family 10
- [ 1.160152] NET: Registered protocol family 17
- [ 1.169370] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 1.194618] 8021q: 802.1Q VLAN Support v1.8
- [ 1.225085] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
- [ 1.241366] Freeing unused kernel memory: 196K (8034f000 - 80380000)
- [ 3.555339] init: Console is alive
- [ 3.562823] init: - watchdog -
- [ 6.436738] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 6.607786] usbcore: registered new interface driver usbfs
- [ 6.619170] usbcore: registered new interface driver hub
- [ 6.630159] usbcore: registered new device driver usb
- [ 6.707424] SCSI subsystem initialized
- [ 6.726569] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 6.742928] ehci-platform: EHCI generic platform driver
- [ 6.764118] phy phy-usbphy.0: remote usb device wakeup disabled
- [ 6.775995] phy phy-usbphy.0: UTMI 16bit 30MHz
- [ 6.784984] ehci-platform 101c0000.ehci: EHCI Host Controller
- [ 6.796606] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
- [ 6.812754] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
- [ 6.841574] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
- [ 6.856415] hub 1-0:1.0: USB hub found
- [ 6.865116] hub 1-0:1.0: 1 port detected
- [ 6.878664] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 6.893904] ohci-platform: OHCI generic platform driver
- [ 6.904967] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
- [ 6.918749] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
- [ 6.934848] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
- [ 7.007558] hub 2-0:1.0: USB hub found
- [ 7.016177] hub 2-0:1.0: 1 port detected
- [ 7.036957] usbcore: registered new interface driver usb-storage
- [ 7.050529] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 7.075989] init: - preinit -
- [ 7.390072] usb 1-1: new high-speed USB device number 2 using ehci-platform
- [ 7.885518] random: procd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
- [ 7.904702] usb-storage 1-1:1.0: USB Mass Storage device detected
- [ 7.951695] scsi host0: usb-storage 1-1:1.0
- [ 8.356416] rt3050-esw 10110000.esw: link changed 0x00
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 8.953533] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Fit 1.00 PQ: 0 ANSI: 6
- [ 8.975988] sd 0:0:0:0: [sda] 62521344 512-byte logical blocks: (32.0 GB/29.8 GiB)
- [ 8.993626] sd 0:0:0:0: [sda] Write Protect is off
- [ 9.004908] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
- [ 9.033770] sda: sda1
- [ 9.046410] sd 0:0:0:0: [sda] Attached SCSI removable disk
- [ 10.225633] rt3050-esw 10110000.esw: link changed 0x01
- [ 11.902737] mount_root: loading kmods from internal overlay
- [ 11.960992] kmodloader: loading kernel modules from //etc/modules-boot.d/*
- [ 11.978815] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
- [ 14.580731] block: attempting to load /etc/config/fstab
- [ 14.592105] block: unable to load configuration (fstab: Entry not found)
- [ 14.605943] block: no usable configuration
- [ 14.615888] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
- [ 14.638535] urandom-seed: Seed file not found (/etc/urandom.seed)
- [ 14.838742] procd: - early -
- [ 14.845039] procd: - watchdog -
- [ 15.749920] procd: - ubus -
- [ 15.808840] random: ubusd: uninitialized urandom read (4 bytes read, 48 bits of entropy available)
- [ 15.952098] random: ubusd: uninitialized urandom read (4 bytes read, 48 bits of entropy available)
- [ 15.971221] random: ubusd: uninitialized urandom read (4 bytes read, 48 bits of entropy available)
- [ 15.989545] random: ubusd: uninitialized urandom read (4 bytes read, 48 bits of entropy available)
- [ 16.008608] random: ubusd: uninitialized urandom read (4 bytes read, 48 bits of entropy available)
- [ 16.026867] random: ubusd: uninitialized urandom read (4 bytes read, 48 bits of entropy available)
- [ 16.045590] random: ubusd: uninitialized urandom read (4 bytes read, 48 bits of entropy available)
- [ 16.064329] random: ubusd: uninitialized urandom read (4 bytes read, 48 bits of entropy available)
- [ 16.083544] procd: - init -
- Please press Enter to activate this console.
- [ 16.562903] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 16.667864] loop: module loaded
- [ 16.693219] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 16.748216] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
- [ 16.764344] Backport generated by backports.git backports-20160324-13-g24da7d3c
- [ 16.926195] batman_adv: B.A.T.M.A.N. advanced 2016.5 (compatibility version 15) loaded
- [ 16.969100] Bridge firewalling registered
- [ 17.008840] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 17.146343] nf_conntrack version 0.5.0 (450 buckets, 1800 max)
- [ 17.365719] xt_time: kernel timezone is -0000
- [ 17.456666] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
- [ 17.471238] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected
- [ 17.486782] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected
- [ 17.581953] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 19.129133] random: jshn: uninitialized urandom read (4 bytes read, 53 bits of entropy available)
- [ 24.279740] rt3050-esw 10110000.esw: link changed 0x00
- [ 26.344181] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
- [ 26.426560] rt3050-esw 10110000.esw: link changed 0x01
- [ 31.316375] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
- [ 31.366398] jffs2_build_filesystem(): unlocking the mtd device... done.
- [ 31.379746] jffs2_build_filesystem(): erasing all blocks after the end marker...
- [ 31.534411] device eth0 entered promiscuous mode
- [ 31.594901] br-lan: port 1(eth0) entered forwarding state
- [ 31.605905] br-lan: port 1(eth0) entered forwarding state
- [ 33.601530] br-lan: port 1(eth0) entered forwarding state
- [ 41.053338] done.
- [ 41.057259] jffs2: notice: (958) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 44.981546] random: nonblocking pool is initialized
- [ 46.082927] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
- [ 87.155663] Adding 32764k swap on /mnt/usb/external_fs/OpenWRT.swap. Priority:-1 extents:1 across:32764k
- [ 87.243750] EXT4-fs (loop0): couldn't mount as ext3 due to feature incompatibilities
- [ 87.274642] EXT4-fs (loop0): couldn't mount as ext2 due to feature incompatibilities
- [ 87.408128] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null)
- [ 105.642334] br-lan: port 1(eth0) entered disabled state
- [ 105.672026] device eth0 left promiscuous mode
- [ 105.680877] br-lan: port 1(eth0) entered disabled state
- [ 105.706319] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
- [ 110.074336] reboot: Restarting system
- U-Boot 1.1.7 (Dec 13 2011 - 13:49:42)
- Board: Ralink APSoC DRAM: 32 MB
- relocate_code Pointer at: 81fb4000
- ******************************
- Software System Reset Occurred
- ******************************
- spi_wait_nsec: 42
- spi device id: 7f 9d 46 7f 9d (9d467f9d)
- Warning: un-recognized chip ID, please update bootloader!
- raspi_read: from:30000 len:1000
- .*** Warning - bad CRC, using default environment
- ============================================
- Ralink UBoot Version: 3.6.0.0
- --------------------------------------------
- ASIC 5350_MP (Port5<->None)
- DRAM_CONF_FROM: Boot-Strapping
- DRAM_TYPE: SDRAM
- DRAM_SIZE: 256 Mbits
- DRAM_WIDTH: 16 bits
- DRAM_TOTAL_WIDTH: 16 bits
- TOTAL_MEMORY_SIZE: 32 MBytes
- Flash component: SPI Flash
- Date:Dec 13 2011 Time:13:49:42
- ============================================
- icache: sets:256, ways:4, linesz:32 ,total:32768
- dcache: sets:128, ways:4, linesz:32 ,total:16384
- ##### The CPU freq = 360 MHZ ####
- estimate memory size =32 Mbytes
- raspi_read: from:40028 len:6
- .
- raspi_read: from:0 len:30004
- ....*************Is_update = 0 plat = 1**************
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 7: Load Boot Loader code then write to Flash via Serial.
- 9: Load Boot Loader code then write to Flash via TFTP.
- 1 0
- 3: System Boot system code via Flash.
- ## Booting image at bc050000 ...
- raspi_read: from:50000 len:40
- . Image Name: MIPS LEDE Linux-4.4.61
- Created: 2017-04-17 16:15:53 UTC
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 1158946 Bytes = 1.1 MB
- Load Address: 80000000
- Entry Point: 80000000
- raspi_read: from:50040 len:11af22
- .................. Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80000000) ...
- ## Giving linux memsize in MB, 32
- Starting kernel ...
- [ 0.000000] Linux version 4.4.61 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3102-0224e32) ) #0 Sat Apr 15 16:13:45 2017
- [ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
- [ 0.000000] MIPS: machine is A5-V11
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 02000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
- [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
- [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
- [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Writing ErrCtl register=00069b50
- [ 0.000000] Readback ErrCtl register=00069b50
- [ 0.000000] Memory: 28612K/32768K available (2888K kernel code, 136K rwdata, 356K rodata, 196K init, 196K bss, 4156K reserved, 0K cma-reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:256
- [ 0.000000] CPU Clock: 360MHz
- [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
- [ 0.000000] systick: running - mult: 214748, shift: 32
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 10618113593 ns
- [ 0.000015] sched_clock: 32 bits at 180MHz, resolution 5ns, wraps every 11930464253ns
- [ 0.015682] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
- [ 0.090885] pid_max: default: 32768 minimum: 301
- [ 0.100299] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.113376] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.136774] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.156350] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 0.168554] pinctrl core: initialized pinctrl subsystem
- [ 0.181387] NET: Registered protocol family 16
- [ 0.200332] Can't analyze schedule() prologue at 8000ac9c
- [ 0.242020] rt2880_gpio 10000600.gpio: registering 22 gpios
- [ 0.253147] rt2880_gpio 10000600.gpio: registering 22 irq handlers
- [ 0.265844] rt2880_gpio 10000660.gpio: registering 6 gpios
- [ 0.276782] rt2880_gpio 10000660.gpio: registering 6 irq handlers
- [ 0.291442] clocksource: Switched to clocksource MIPS
- [ 0.303716] NET: Registered protocol family 2
- [ 0.314349] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.328239] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.340822] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.353681] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.365299] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.378266] NET: Registered protocol family 1
- [ 0.397348] rt-timer 10000100.timer: maximum frequency is 3662Hz
- [ 0.410816] Crashlog allocated RAM at address 0x1f00000
- [ 0.456876] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.468468] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.494142] io scheduler noop registered
- [ 0.501917] io scheduler deadline registered (default)
- [ 0.512474] ralink-usb-phy usbphy: invalid resource
- [ 0.523568] gpio-export gpio_export: 2 gpio(s) exported
- [ 0.534373] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 0.553966] console [ttyS0] disabled
- [ 0.561014] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
- [ 0.580841] console [ttyS0] enabled
- [ 0.580841] console [ttyS0] enabled
- [ 0.594612] bootconsole [early0] disabled
- [ 0.594612] bootconsole [early0] disabled
- [ 0.626200] spi spi0.0: force spi mode3
- [ 0.634856] m25p80 spi0.0: pm25lq032 (4096 Kbytes)
- [ 0.644606] 4 ofpart partitions found on MTD device spi0.0
- [ 0.655590] Creating 4 MTD partitions on "spi0.0":
- [ 0.665202] 0x000000000000-0x000000030000 : "u-boot"
- [ 0.678831] 0x000000030000-0x000000040000 : "u-boot-env"
- [ 0.693569] 0x000000040000-0x000000050000 : "factory"
- [ 0.707663] 0x000000050000-0x000000400000 : "firmware"
- [ 1.014209] 2 uimage-fw partitions found on MTD device firmware
- [ 1.026145] 0x000000050000-0x00000016af62 : "kernel"
- [ 1.039348] 0x00000016af62-0x000000400000 : "rootfs"
- [ 1.053285] mtd: device 5 (rootfs) set to be root filesystem
- [ 1.064903] 1 squashfs-split partitions found on MTD device rootfs
- [ 1.077324] 0x0000003a3000-0x000000400000 : "rootfs_data"
- [ 1.098408] rt3050-esw 10110000.esw: link changed 0x00
- [ 1.112430] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
- [ 1.130073] rt2880_wdt 10000120.watchdog: Initialized
- [ 1.142985] NET: Registered protocol family 10
- [ 1.160153] NET: Registered protocol family 17
- [ 1.169370] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 1.194620] 8021q: 802.1Q VLAN Support v1.8
- [ 1.225089] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
- [ 1.241371] Freeing unused kernel memory: 196K (8034f000 - 80380000)
- [ 3.555304] init: Console is alive
- [ 3.562787] init: - watchdog -
- [ 6.436342] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 6.607367] usbcore: registered new interface driver usbfs
- [ 6.618754] usbcore: registered new interface driver hub
- [ 6.629741] usbcore: registered new device driver usb
- [ 6.707009] SCSI subsystem initialized
- [ 6.726173] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 6.742535] ehci-platform: EHCI generic platform driver
- [ 6.763724] phy phy-usbphy.0: remote usb device wakeup disabled
- [ 6.775601] phy phy-usbphy.0: UTMI 16bit 30MHz
- [ 6.784590] ehci-platform 101c0000.ehci: EHCI Host Controller
- [ 6.796212] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
- [ 6.812358] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
- [ 6.841577] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
- [ 6.856418] hub 1-0:1.0: USB hub found
- [ 6.865122] hub 1-0:1.0: 1 port detected
- [ 6.878666] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 6.893894] ohci-platform: OHCI generic platform driver
- [ 6.904956] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
- [ 6.918738] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
- [ 6.934838] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
- [ 7.007560] hub 2-0:1.0: USB hub found
- [ 7.016179] hub 2-0:1.0: 1 port detected
- [ 7.037058] usbcore: registered new interface driver usb-storage
- [ 7.050632] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 7.076086] init: - preinit -
- [ 7.390053] usb 1-1: new high-speed USB device number 2 using ehci-platform
- [ 7.879898] random: procd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
- [ 7.902387] usb-storage 1-1:1.0: USB Mass Storage device detected
- [ 7.942947] scsi host0: usb-storage 1-1:1.0
- [ 8.355942] rt3050-esw 10110000.esw: link changed 0x00
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 8.953764] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Fit 1.00 PQ: 0 ANSI: 6
- [ 8.976212] sd 0:0:0:0: [sda] 62521344 512-byte logical blocks: (32.0 GB/29.8 GiB)
- [ 8.993726] sd 0:0:0:0: [sda] Write Protect is off
- [ 9.005008] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
- [ 9.034621] sda: sda1
- [ 9.047139] sd 0:0:0:0: [sda] Attached SCSI removable disk
- [ 10.438172] rt3050-esw 10110000.esw: link changed 0x01
- [ 11.902666] mount_root: loading kmods from internal overlay
- [ 11.960812] kmodloader: loading kernel modules from //etc/modules-boot.d/*
- [ 11.978676] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
- [ 14.435008] jffs2: notice: (377) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 14.467202] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
- [ 14.494005] block: extroot: not configured
- [ 14.574838] jffs2: notice: (374) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 16.376062] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
- [ 16.400046] block: extroot: not configured
- [ 16.410620] mount_root: switching to jffs2 overlay
- [ 16.435695] urandom-seed: Seed file not found (/etc/urandom.seed)
- [ 16.653348] procd: - early -
- [ 16.659387] procd: - watchdog -
- [ 17.572964] procd: - ubus -
- [ 17.630555] random: ubusd: uninitialized urandom read (4 bytes read, 77 bits of entropy available)
- [ 17.682609] random: ubusd: uninitialized urandom read (4 bytes read, 77 bits of entropy available)
- [ 17.721764] random: ubusd: uninitialized urandom read (4 bytes read, 77 bits of entropy available)
- [ 17.747572] random: ubusd: uninitialized urandom read (4 bytes read, 77 bits of entropy available)
- [ 17.766048] random: ubusd: uninitialized urandom read (4 bytes read, 77 bits of entropy available)
- [ 17.786207] random: ubusd: uninitialized urandom read (4 bytes read, 81 bits of entropy available)
- [ 17.806269] random: ubusd: uninitialized urandom read (4 bytes read, 82 bits of entropy available)
- [ 17.832782] procd: - init -
- Please press Enter to activate this console.
- [ 18.865242] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 19.015105] loop: module loaded
- [ 19.042051] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 19.090161] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
- [ 19.106347] Backport generated by backports.git backports-20160324-13-g24da7d3c
- [ 19.242333] batman_adv: B.A.T.M.A.N. advanced 2016.5 (compatibility version 15) loaded
- [ 19.279657] Bridge firewalling registered
- [ 19.318664] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 19.430057] nf_conntrack version 0.5.0 (450 buckets, 1800 max)
- [ 19.521610] random: nonblocking pool is initialized
- [ 19.632908] xt_time: kernel timezone is -0000
- [ 19.734917] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
- [ 19.749487] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected
- [ 19.765022] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected
- [ 19.837515] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 25.393866] rt3050-esw 10110000.esw: link changed 0x00
- [ 27.276685] rt3050-esw 10110000.esw: link changed 0x01
- [ 27.964407] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
- [ 28.355542] Adding 32764k swap on /mnt/usb/external_fs/OpenWRT.swap. Priority:-1 extents:1 across:32764k
- [ 28.493813] EXT4-fs (loop0): couldn't mount as ext3 due to feature incompatibilities
- [ 28.553628] EXT4-fs (loop0): couldn't mount as ext2 due to feature incompatibilities
- [ 28.667644] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null)
- [ 32.144679] device eth0 entered promiscuous mode
- [ 32.184848] br-lan: port 1(eth0) entered forwarding state
- [ 32.195847] br-lan: port 1(eth0) entered forwarding state
- [ 34.191494] br-lan: port 1(eth0) entered forwarding state
- [ 50.179178] br-lan: port 1(eth0) entered disabled state
- [ 50.212011] device eth0 left promiscuous mode
- [ 50.220860] br-lan: port 1(eth0) entered disabled state
- [ 50.246462] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
- [ 54.617943] reboot: Restarting system
- U-Boot 1.1.7 (Dec 13 2011 - 13:49:42)
- Board: Ralink APSoC DRAM: 32 MB
- relocate_code Pointer at: 81fb4000
- ******************************
- Software System Reset Occurred
- ******************************
- spi_wait_nsec: 42
- spi device id: 7f 9d 46 7f 9d (9d467f9d)
- Warning: un-recognized chip ID, please update bootloader!
- raspi_read: from:30000 len:1000
- .*** Warning - bad CRC, using default environment
- ============================================
- Ralink UBoot Version: 3.6.0.0
- --------------------------------------------
- ASIC 5350_MP (Port5<->None)
- DRAM_CONF_FROM: Boot-Strapping
- DRAM_TYPE: SDRAM
- DRAM_SIZE: 256 Mbits
- DRAM_WIDTH: 16 bits
- DRAM_TOTAL_WIDTH: 16 bits
- TOTAL_MEMORY_SIZE: 32 MBytes
- Flash component: SPI Flash
- Date:Dec 13 2011 Time:13:49:42
- ============================================
- icache: sets:256, ways:4, linesz:32 ,total:32768
- dcache: sets:128, ways:4, linesz:32 ,total:16384
- ##### The CPU freq = 360 MHZ ####
- estimate memory size =32 Mbytes
- raspi_read: from:40028 len:6
- .
- raspi_read: from:0 len:30004
- ....*************Is_update = 0 plat = 1**************
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 7: Load Boot Loader code then write to Flash via Serial.
- 9: Load Boot Loader code then write to Flash via TFTP.
- 1 0
- 3: System Boot system code via Flash.
- ## Booting image at bc050000 ...
- raspi_read: from:50000 len:40
- . Image Name: MIPS LEDE Linux-4.4.61
- Created: 2017-04-17 16:15:53 UTC
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 1158946 Bytes = 1.1 MB
- Load Address: 80000000
- Entry Point: 80000000
- raspi_read: from:50040 len:11af22
- .................. Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80000000) ...
- ## Giving linux memsize in MB, 32
- Starting kernel ...
- [ 0.000000] Linux version 4.4.61 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3102-0224e32) ) #0 Sat Apr 15 16:13:45 2017
- [ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
- [ 0.000000] MIPS: machine is A5-V11
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 02000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
- [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
- [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
- [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Writing ErrCtl register=00069b50
- [ 0.000000] Readback ErrCtl register=00069b50
- [ 0.000000] Memory: 28612K/32768K available (2888K kernel code, 136K rwdata, 356K rodata, 196K init, 196K bss, 4156K reserved, 0K cma-reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:256
- [ 0.000000] CPU Clock: 360MHz
- [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
- [ 0.000000] systick: running - mult: 214748, shift: 32
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 10618113593 ns
- [ 0.000015] sched_clock: 32 bits at 180MHz, resolution 5ns, wraps every 11930464253ns
- [ 0.015683] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
- [ 0.090885] pid_max: default: 32768 minimum: 301
- [ 0.100300] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.113376] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.136774] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.156350] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 0.168555] pinctrl core: initialized pinctrl subsystem
- [ 0.181389] NET: Registered protocol family 16
- [ 0.200336] Can't analyze schedule() prologue at 8000ac9c
- [ 0.242019] rt2880_gpio 10000600.gpio: registering 22 gpios
- [ 0.253147] rt2880_gpio 10000600.gpio: registering 22 irq handlers
- [ 0.265844] rt2880_gpio 10000660.gpio: registering 6 gpios
- [ 0.276782] rt2880_gpio 10000660.gpio: registering 6 irq handlers
- [ 0.291442] clocksource: Switched to clocksource MIPS
- [ 0.303716] NET: Registered protocol family 2
- [ 0.314349] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.328239] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.340822] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.353682] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.365299] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.378265] NET: Registered protocol family 1
- [ 0.397344] rt-timer 10000100.timer: maximum frequency is 3662Hz
- [ 0.410814] Crashlog allocated RAM at address 0x1f00000
- [ 0.456871] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.468463] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.494130] io scheduler noop registered
- [ 0.501907] io scheduler deadline registered (default)
- [ 0.512462] ralink-usb-phy usbphy: invalid resource
- [ 0.523555] gpio-export gpio_export: 2 gpio(s) exported
- [ 0.534361] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 0.553951] console [ttyS0] disabled
- [ 0.561000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
- [ 0.580826] console [ttyS0] enabled
- [ 0.580826] console [ttyS0] enabled
- [ 0.594596] bootconsole [early0] disabled
- [ 0.594596] bootconsole [early0] disabled
- [ 0.626181] spi spi0.0: force spi mode3
- [ 0.634837] m25p80 spi0.0: pm25lq032 (4096 Kbytes)
- [ 0.644585] 4 ofpart partitions found on MTD device spi0.0
- [ 0.655569] Creating 4 MTD partitions on "spi0.0":
- [ 0.665181] 0x000000000000-0x000000030000 : "u-boot"
- [ 0.678811] 0x000000030000-0x000000040000 : "u-boot-env"
- [ 0.693554] 0x000000040000-0x000000050000 : "factory"
- [ 0.707647] 0x000000050000-0x000000400000 : "firmware"
- [ 1.014190] 2 uimage-fw partitions found on MTD device firmware
- [ 1.026127] 0x000000050000-0x00000016af62 : "kernel"
- [ 1.039332] 0x00000016af62-0x000000400000 : "rootfs"
- [ 1.053272] mtd: device 5 (rootfs) set to be root filesystem
- [ 1.064890] 1 squashfs-split partitions found on MTD device rootfs
- [ 1.077311] 0x0000003a3000-0x000000400000 : "rootfs_data"
- [ 1.098408] rt3050-esw 10110000.esw: link changed 0x00
- [ 1.112430] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
- [ 1.130071] rt2880_wdt 10000120.watchdog: Initialized
- [ 1.142983] NET: Registered protocol family 10
- [ 1.160144] NET: Registered protocol family 17
- [ 1.169363] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 1.194612] 8021q: 802.1Q VLAN Support v1.8
- [ 1.225076] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
- [ 1.241358] Freeing unused kernel memory: 196K (8034f000 - 80380000)
- [ 3.555202] init: Console is alive
- [ 3.562693] init: - watchdog -
- [ 6.436530] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 6.607586] usbcore: registered new interface driver usbfs
- [ 6.618971] usbcore: registered new interface driver hub
- [ 6.629962] usbcore: registered new device driver usb
- [ 6.707746] SCSI subsystem initialized
- [ 6.726976] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 6.743317] ehci-platform: EHCI generic platform driver
- [ 6.764508] phy phy-usbphy.0: remote usb device wakeup disabled
- [ 6.776385] phy phy-usbphy.0: UTMI 16bit 30MHz
- [ 6.785374] ehci-platform 101c0000.ehci: EHCI Host Controller
- [ 6.796995] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
- [ 6.813143] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
- [ 6.841574] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
- [ 6.856414] hub 1-0:1.0: USB hub found
- [ 6.865123] hub 1-0:1.0: 1 port detected
- [ 6.878689] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 6.893923] ohci-platform: OHCI generic platform driver
- [ 6.904987] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
- [ 6.918767] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
- [ 6.934863] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
- [ 7.007553] hub 2-0:1.0: USB hub found
- [ 7.016181] hub 2-0:1.0: 1 port detected
- [ 7.036998] usbcore: registered new interface driver usb-storage
- [ 7.050589] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 7.076045] init: - preinit -
- [ 7.390058] usb 1-1: new high-speed USB device number 2 using ehci-platform
- [ 7.885689] random: procd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
- [ 7.904873] usb-storage 1-1:1.0: USB Mass Storage device detected
- [ 7.951636] scsi host0: usb-storage 1-1:1.0
- [ 8.356712] rt3050-esw 10110000.esw: link changed 0x00
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 8.953551] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Fit 1.00 PQ: 0 ANSI: 6
- [ 8.975978] sd 0:0:0:0: [sda] 62521344 512-byte logical blocks: (32.0 GB/29.8 GiB)
- [ 8.993397] sd 0:0:0:0: [sda] Write Protect is off
- [ 9.004669] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
- [ 9.033529] sda: sda1
- [ 9.046177] sd 0:0:0:0: [sda] Attached SCSI removable disk
- [ 10.307855] rt3050-esw 10110000.esw: link changed 0x01
- [ 11.908282] mount_root: loading kmods from internal overlay
- [ 11.966613] kmodloader: loading kernel modules from //etc/modules-boot.d/*
- [ 11.984637] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
- [ 14.435283] jffs2: notice: (377) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 14.467483] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
- [ 14.494612] block: extroot: not configured
- [ 14.569884] jffs2: notice: (374) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 16.371135] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
- [ 16.395540] block: extroot: not configured
- [ 16.406250] mount_root: switching to jffs2 overlay
- [ 16.429399] urandom-seed: Seed file not found (/etc/urandom.seed)
- [ 16.645824] procd: - early -
- [ 16.652014] procd: - watchdog -
- [ 17.564848] procd: - ubus -
- [ 17.723569] random: ubusd: uninitialized urandom read (4 bytes read, 80 bits of entropy available)
- [ 17.748869] random: ubusd: uninitialized urandom read (4 bytes read, 81 bits of entropy available)
- [ 17.768031] random: ubusd: uninitialized urandom read (4 bytes read, 82 bits of entropy available)
- [ 17.788529] random: ubusd: uninitialized urandom read (4 bytes read, 82 bits of entropy available)
- [ 17.808224] random: ubusd: uninitialized urandom read (4 bytes read, 82 bits of entropy available)
- [ 17.828535] random: ubusd: uninitialized urandom read (4 bytes read, 82 bits of entropy available)
- [ 17.849093] random: ubusd: uninitialized urandom read (4 bytes read, 82 bits of entropy available)
- [ 17.871597] procd: - init -
- Please press Enter to activate this console.
- [ 18.939535] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 19.093012] loop: module loaded
- [ 19.124358] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 19.178509] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
- [ 19.194634] Backport generated by backports.git backports-20160324-13-g24da7d3c
- [ 19.332535] batman_adv: B.A.T.M.A.N. advanced 2016.5 (compatibility version 15) loaded
- [ 19.367830] Bridge firewalling registered
- [ 19.395831] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 19.516705] nf_conntrack version 0.5.0 (450 buckets, 1800 max)
- [ 19.700552] xt_time: kernel timezone is -0000
- [ 19.745110] random: nonblocking pool is initialized
- [ 19.789522] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
- [ 19.804146] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected
- [ 19.819695] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected
- [ 19.858595] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 25.431931] rt3050-esw 10110000.esw: link changed 0x00
- [ 27.484580] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
- [ 27.726188] rt3050-esw 10110000.esw: link changed 0x01
- [ 28.110025] Adding 32764k swap on /mnt/usb/external_fs/OpenWRT.swap. Priority:-1 extents:1 across:32764k
- [ 28.233690] EXT4-fs (loop0): couldn't mount as ext3 due to feature incompatibilities
- [ 28.294614] EXT4-fs (loop0): couldn't mount as ext2 due to feature incompatibilities
- [ 28.411564] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null)
- [ 32.184628] device eth0 entered promiscuous mode
- [ 32.224856] br-lan: port 1(eth0) entered forwarding state
- [ 32.235864] br-lan: port 1(eth0) entered forwarding state
- [ 34.231551] br-lan: port 1(eth0) entered forwarding state
- [ 50.981023] br-lan: port 1(eth0) entered disabled state
- [ 51.012030] device eth0 left promiscuous mode
- [ 51.021173] br-lan: port 1(eth0) entered disabled state
- [ 51.048604] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
- [ 55.419728] reboot: Restarting system
- U-Boot 1.1.7 (Dec 13 2011 - 13:49:42)
- Board: Ralink APSoC DRAM: 32 MB
- relocate_code Pointer at: 81fb4000
- ******************************
- Software System Reset Occurred
- ******************************
- spi_wait_nsec: 42
- spi device id: 7f 9d 46 7f 9d (9d467f9d)
- Warning: un-recognized chip ID, please update bootloader!
- raspi_read: from:30000 len:1000
- .*** Warning - bad CRC, using default environment
- ============================================
- Ralink UBoot Version: 3.6.0.0
- --------------------------------------------
- ASIC 5350_MP (Port5<->None)
- DRAM_CONF_FROM: Boot-Strapping
- DRAM_TYPE: SDRAM
- DRAM_SIZE: 256 Mbits
- DRAM_WIDTH: 16 bits
- DRAM_TOTAL_WIDTH: 16 bits
- TOTAL_MEMORY_SIZE: 32 MBytes
- Flash component: SPI Flash
- Date:Dec 13 2011 Time:13:49:42
- ============================================
- icache: sets:256, ways:4, linesz:32 ,total:32768
- dcache: sets:128, ways:4, linesz:32 ,total:16384
- ##### The CPU freq = 360 MHZ ####
- estimate memory size =32 Mbytes
- raspi_read: from:40028 len:6
- .
- raspi_read: from:0 len:30004
- ....*************Is_update = 0 plat = 1**************
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 7: Load Boot Loader code then write to Flash via Serial.
- 9: Load Boot Loader code then write to Flash via TFTP.
- 1 0
- 3: System Boot system code via Flash.
- ## Booting image at bc050000 ...
- raspi_read: from:50000 len:40
- . Image Name: MIPS LEDE Linux-4.4.61
- Created: 2017-04-17 16:15:53 UTC
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 1158946 Bytes = 1.1 MB
- Load Address: 80000000
- Entry Point: 80000000
- raspi_read: from:50040 len:11af22
- .................. Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80000000) ...
- ## Giving linux memsize in MB, 32
- Starting kernel ...
- [ 0.000000] Linux version 4.4.61 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3102-0224e32) ) #0 Sat Apr 15 16:13:45 2017
- [ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
- [ 0.000000] MIPS: machine is A5-V11
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 02000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
- [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
- [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
- [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Writing ErrCtl register=00069b50
- [ 0.000000] Readback ErrCtl register=00069b50
- [ 0.000000] Memory: 28612K/32768K available (2888K kernel code, 136K rwdata, 356K rodata, 196K init, 196K bss, 4156K reserved, 0K cma-reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:256
- [ 0.000000] CPU Clock: 360MHz
- [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
- [ 0.000000] systick: running - mult: 214748, shift: 32
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 10618113593 ns
- [ 0.000015] sched_clock: 32 bits at 180MHz, resolution 5ns, wraps every 11930464253ns
- [ 0.015683] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
- [ 0.090885] pid_max: default: 32768 minimum: 301
- [ 0.100300] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.113377] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.136776] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.156352] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 0.168557] pinctrl core: initialized pinctrl subsystem
- [ 0.181389] NET: Registered protocol family 16
- [ 0.200335] Can't analyze schedule() prologue at 8000ac9c
- [ 0.242017] rt2880_gpio 10000600.gpio: registering 22 gpios
- [ 0.253145] rt2880_gpio 10000600.gpio: registering 22 irq handlers
- [ 0.265840] rt2880_gpio 10000660.gpio: registering 6 gpios
- [ 0.276779] rt2880_gpio 10000660.gpio: registering 6 irq handlers
- [ 0.291439] clocksource: Switched to clocksource MIPS
- [ 0.303713] NET: Registered protocol family 2
- [ 0.314348] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.328238] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.340821] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.353680] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.365297] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.378263] NET: Registered protocol family 1
- [ 0.397344] rt-timer 10000100.timer: maximum frequency is 3662Hz
- [ 0.410813] Crashlog allocated RAM at address 0x1f00000
- [ 0.456878] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.468471] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.494146] io scheduler noop registered
- [ 0.501922] io scheduler deadline registered (default)
- [ 0.512477] ralink-usb-phy usbphy: invalid resource
- [ 0.523570] gpio-export gpio_export: 2 gpio(s) exported
- [ 0.534375] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 0.553967] console [ttyS0] disabled
- [ 0.561015] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
- [ 0.580842] console [ttyS0] enabled
- [ 0.580842] console [ttyS0] enabled
- [ 0.594612] bootconsole [early0] disabled
- [ 0.594612] bootconsole [early0] disabled
- [ 0.626202] spi spi0.0: force spi mode3
- [ 0.634859] m25p80 spi0.0: pm25lq032 (4096 Kbytes)
- [ 0.644609] 4 ofpart partitions found on MTD device spi0.0
- [ 0.655593] Creating 4 MTD partitions on "spi0.0":
- [ 0.665205] 0x000000000000-0x000000030000 : "u-boot"
- [ 0.678834] 0x000000030000-0x000000040000 : "u-boot-env"
- [ 0.693570] 0x000000040000-0x000000050000 : "factory"
- [ 0.707662] 0x000000050000-0x000000400000 : "firmware"
- [ 1.014207] 2 uimage-fw partitions found on MTD device firmware
- [ 1.026143] 0x000000050000-0x00000016af62 : "kernel"
- [ 1.039347] 0x00000016af62-0x000000400000 : "rootfs"
- [ 1.053285] mtd: device 5 (rootfs) set to be root filesystem
- [ 1.064903] 1 squashfs-split partitions found on MTD device rootfs
- [ 1.077324] 0x0000003a3000-0x000000400000 : "rootfs_data"
- [ 1.098409] rt3050-esw 10110000.esw: link changed 0x00
- [ 1.112432] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
- [ 1.130075] rt2880_wdt 10000120.watchdog: Initialized
- [ 1.142988] NET: Registered protocol family 10
- [ 1.160155] NET: Registered protocol family 17
- [ 1.169374] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 1.194624] 8021q: 802.1Q VLAN Support v1.8
- [ 1.225090] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
- [ 1.241373] Freeing unused kernel memory: 196K (8034f000 - 80380000)
- [ 3.555380] init: Console is alive
- [ 3.562873] init: - watchdog -
- [ 6.436506] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 6.607643] usbcore: registered new interface driver usbfs
- [ 6.619030] usbcore: registered new interface driver hub
- [ 6.630019] usbcore: registered new device driver usb
- [ 6.707394] SCSI subsystem initialized
- [ 6.726574] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 6.742931] ehci-platform: EHCI generic platform driver
- [ 6.764123] phy phy-usbphy.0: remote usb device wakeup disabled
- [ 6.776000] phy phy-usbphy.0: UTMI 16bit 30MHz
- [ 6.784988] ehci-platform 101c0000.ehci: EHCI Host Controller
- [ 6.796611] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
- [ 6.812759] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
- [ 6.841573] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
- [ 6.856419] hub 1-0:1.0: USB hub found
- [ 6.865121] hub 1-0:1.0: 1 port detected
- [ 6.878701] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 6.893939] ohci-platform: OHCI generic platform driver
- [ 6.905002] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
- [ 6.918784] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
- [ 6.934879] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
- [ 7.007553] hub 2-0:1.0: USB hub found
- [ 7.016170] hub 2-0:1.0: 1 port detected
- [ 7.036988] usbcore: registered new interface driver usb-storage
- [ 7.050559] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 7.076024] init: - preinit -
- [ 7.390052] usb 1-1: new high-speed USB device number 2 using ehci-platform
- [ 7.885693] random: procd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
- [ 7.904877] usb-storage 1-1:1.0: USB Mass Storage device detected
- [ 7.951636] scsi host0: usb-storage 1-1:1.0
- [ 8.356899] rt3050-esw 10110000.esw: link changed 0x00
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 8.953540] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Fit 1.00 PQ: 0 ANSI: 6
- [ 8.975996] sd 0:0:0:0: [sda] 62521344 512-byte logical blocks: (32.0 GB/29.8 GiB)
- [ 8.993638] sd 0:0:0:0: [sda] Write Protect is off
- [ 9.004910] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
- [ 9.033771] sda: sda1
- [ 9.046292] sd 0:0:0:0: [sda] Attached SCSI removable disk
- [ 10.619339] rt3050-esw 10110000.esw: link changed 0x01
- [ 11.910046] mount_root: loading kmods from internal overlay
- [ 11.968644] kmodloader: loading kernel modules from //etc/modules-boot.d/*
- [ 11.986510] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
- [ 14.441931] jffs2: notice: (377) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 14.474116] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
- [ 14.499060] block: extroot: not configured
- [ 14.579082] jffs2: notice: (374) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 16.377008] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
- [ 16.400374] block: extroot: not configured
- [ 16.410922] mount_root: switching to jffs2 overlay
- [ 16.433425] urandom-seed: Seed file not found (/etc/urandom.seed)
- [ 16.650450] procd: - early -
- [ 16.656631] procd: - watchdog -
- [ 17.570829] procd: - ubus -
- [ 17.632869] random: ubusd: uninitialized urandom read (4 bytes read, 76 bits of entropy available)
- [ 17.681213] random: ubusd: uninitialized urandom read (4 bytes read, 76 bits of entropy available)
- [ 17.725089] random: ubusd: uninitialized urandom read (4 bytes read, 76 bits of entropy available)
- [ 17.757474] random: ubusd: uninitialized urandom read (4 bytes read, 80 bits of entropy available)
- [ 17.790931] random: ubusd: uninitialized urandom read (4 bytes read, 81 bits of entropy available)
- [ 17.820517] random: ubusd: uninitialized urandom read (4 bytes read, 83 bits of entropy available)
- [ 17.843536] random: ubusd: uninitialized urandom read (4 bytes read, 83 bits of entropy available)
- [ 17.863972] procd: - init -
- Please press Enter to activate this console.
- [ 18.892498] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 19.037898] loop: module loaded
- [ 19.066476] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 19.117062] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
- [ 19.133251] Backport generated by backports.git backports-20160324-13-g24da7d3c
- [ 19.261958] batman_adv: B.A.T.M.A.N. advanced 2016.5 (compatibility version 15) loaded
- [ 19.301594] Bridge firewalling registered
- [ 19.338745] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 19.448750] nf_conntrack version 0.5.0 (450 buckets, 1800 max)
- [ 19.603078] random: nonblocking pool is initialized
- [ 19.654600] xt_time: kernel timezone is -0000
- [ 19.758329] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
- [ 19.772920] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected
- [ 19.788451] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected
- [ 19.856601] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 25.395222] rt3050-esw 10110000.esw: link changed 0x00
- [ 27.469215] rt3050-esw 10110000.esw: link changed 0x01
- [ 27.994430] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
- [ 28.385559] Adding 32764k swap on /mnt/usb/external_fs/OpenWRT.swap. Priority:-1 extents:1 across:32764k
- [ 28.523890] EXT4-fs (loop0): couldn't mount as ext3 due to feature incompatibilities
- [ 28.583667] EXT4-fs (loop0): couldn't mount as ext2 due to feature incompatibilities
- [ 28.700294] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null)
- [ 32.184516] device eth0 entered promiscuous mode
- [ 32.214750] br-lan: port 1(eth0) entered forwarding state
- [ 32.225748] br-lan: port 1(eth0) entered forwarding state
- [ 34.221491] br-lan: port 1(eth0) entered forwarding state
- [ 316.103153] br-lan: port 1(eth0) entered disabled state
- [ 316.132020] device eth0 left promiscuous mode
- [ 316.140866] br-lan: port 1(eth0) entered disabled state
- [ 316.169928] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
- [ 320.513333] reboot: Restarting system
- U-Boot 1.1.7 (Dec 13 2011 - 13:49:42)
- Board: Ralink APSoC DRAM: 32 MB
- relocate_code Pointer at: 81fb4000
- ******************************
- Software System Reset Occurred
- ******************************
- spi_wait_nsec: 42
- spi device id: 7f 9d 46 7f 9d (9d467f9d)
- Warning: un-recognized chip ID, please update bootloader!
- raspi_read: from:30000 len:1000
- .*** Warning - bad CRC, using default environment
- ============================================
- Ralink UBoot Version: 3.6.0.0
- --------------------------------------------
- ASIC 5350_MP (Port5<->None)
- DRAM_CONF_FROM: Boot-Strapping
- DRAM_TYPE: SDRAM
- DRAM_SIZE: 256 Mbits
- DRAM_WIDTH: 16 bits
- DRAM_TOTAL_WIDTH: 16 bits
- TOTAL_MEMORY_SIZE: 32 MBytes
- Flash component: SPI Flash
- Date:Dec 13 2011 Time:13:49:42
- ============================================
- icache: sets:256, ways:4, linesz:32 ,total:32768
- dcache: sets:128, ways:4, linesz:32 ,total:16384
- ##### The CPU freq = 360 MHZ ####
- estimate memory size =32 Mbytes
- raspi_read: from:40028 len:6
- .
- raspi_read: from:0 len:30004
- ....*************Is_update = 0 plat = 1**************
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 7: Load Boot Loader code then write to Flash via Serial.
- 9: Load Boot Loader code then write to Flash via TFTP.
- 1 0
- 3: System Boot system code via Flash.
- ## Booting image at bc050000 ...
- raspi_read: from:50000 len:40
- . Image Name: MIPS LEDE Linux-4.4.61
- Created: 2017-04-17 16:15:53 UTC
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 1158946 Bytes = 1.1 MB
- Load Address: 80000000
- Entry Point: 80000000
- raspi_read: from:50040 len:11af22
- .................. Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80000000) ...
- ## Giving linux memsize in MB, 32
- Starting kernel ...
- [ 0.000000] Linux version 4.4.61 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3102-0224e32) ) #0 Sat Apr 15 16:13:45 2017
- [ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
- [ 0.000000] MIPS: machine is A5-V11
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 02000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
- [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
- [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
- [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Writing ErrCtl register=00069b50
- [ 0.000000] Readback ErrCtl register=00069b50
- [ 0.000000] Memory: 28612K/32768K available (2888K kernel code, 136K rwdata, 356K rodata, 196K init, 196K bss, 4156K reserved, 0K cma-reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:256
- [ 0.000000] CPU Clock: 360MHz
- [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
- [ 0.000000] systick: running - mult: 214748, shift: 32
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 10618113593 ns
- [ 0.000015] sched_clock: 32 bits at 180MHz, resolution 5ns, wraps every 11930464253ns
- [ 0.015682] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
- [ 0.090885] pid_max: default: 32768 minimum: 301
- [ 0.100300] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.113377] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.136776] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.156352] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 0.168557] pinctrl core: initialized pinctrl subsystem
- [ 0.181389] NET: Registered protocol family 16
- [ 0.200335] Can't analyze schedule() prologue at 8000ac9c
- [ 0.242017] rt2880_gpio 10000600.gpio: registering 22 gpios
- [ 0.253145] rt2880_gpio 10000600.gpio: registering 22 irq handlers
- [ 0.265840] rt2880_gpio 10000660.gpio: registering 6 gpios
- [ 0.276779] rt2880_gpio 10000660.gpio: registering 6 irq handlers
- [ 0.291440] clocksource: Switched to clocksource MIPS
- [ 0.303713] NET: Registered protocol family 2
- [ 0.314349] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.328239] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.340822] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.353680] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.365298] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.378265] NET: Registered protocol family 1
- [ 0.397344] rt-timer 10000100.timer: maximum frequency is 3662Hz
- [ 0.410813] Crashlog allocated RAM at address 0x1f00000
- [ 0.456878] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.468471] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.494146] io scheduler noop registered
- [ 0.501922] io scheduler deadline registered (default)
- [ 0.512478] ralink-usb-phy usbphy: invalid resource
- [ 0.523570] gpio-export gpio_export: 2 gpio(s) exported
- [ 0.534375] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 0.553967] console [ttyS0] disabled
- [ 0.561016] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
- [ 0.580842] console [ttyS0] enabled
- [ 0.580842] console [ttyS0] enabled
- [ 0.594612] bootconsole [early0] disabled
- [ 0.594612] bootconsole [early0] disabled
- [ 0.626200] spi spi0.0: force spi mode3
- [ 0.634857] m25p80 spi0.0: pm25lq032 (4096 Kbytes)
- [ 0.644607] 4 ofpart partitions found on MTD device spi0.0
- [ 0.655592] Creating 4 MTD partitions on "spi0.0":
- [ 0.665204] 0x000000000000-0x000000030000 : "u-boot"
- [ 0.678833] 0x000000030000-0x000000040000 : "u-boot-env"
- [ 0.693570] 0x000000040000-0x000000050000 : "factory"
- [ 0.707662] 0x000000050000-0x000000400000 : "firmware"
- [ 1.014203] 2 uimage-fw partitions found on MTD device firmware
- [ 1.026138] 0x000000050000-0x00000016af62 : "kernel"
- [ 1.039342] 0x00000016af62-0x000000400000 : "rootfs"
- [ 1.053282] mtd: device 5 (rootfs) set to be root filesystem
- [ 1.064899] 1 squashfs-split partitions found on MTD device rootfs
- [ 1.077320] 0x0000003a3000-0x000000400000 : "rootfs_data"
- [ 1.098407] rt3050-esw 10110000.esw: link changed 0x00
- [ 1.112429] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
- [ 1.130070] rt2880_wdt 10000120.watchdog: Initialized
- [ 1.142983] NET: Registered protocol family 10
- [ 1.160146] NET: Registered protocol family 17
- [ 1.169364] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 1.194613] 8021q: 802.1Q VLAN Support v1.8
- [ 1.225079] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
- [ 1.241360] Freeing unused kernel memory: 196K (8034f000 - 80380000)
- [ 3.555320] init: Console is alive
- [ 3.562805] init: - watchdog -
- [ 6.436667] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 6.607684] usbcore: registered new interface driver usbfs
- [ 6.619066] usbcore: registered new interface driver hub
- [ 6.630057] usbcore: registered new device driver usb
- [ 6.708212] SCSI subsystem initialized
- [ 6.727356] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 6.743747] ehci-platform: EHCI generic platform driver
- [ 6.764939] phy phy-usbphy.0: remote usb device wakeup disabled
- [ 6.776816] phy phy-usbphy.0: UTMI 16bit 30MHz
- [ 6.785805] ehci-platform 101c0000.ehci: EHCI Host Controller
- [ 6.797427] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
- [ 6.813573] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
- [ 6.841573] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
- [ 6.856414] hub 1-0:1.0: USB hub found
- [ 6.865123] hub 1-0:1.0: 1 port detected
- [ 6.878673] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 6.893900] ohci-platform: OHCI generic platform driver
- [ 6.904964] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
- [ 6.918745] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
- [ 6.934843] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
- [ 7.007554] hub 2-0:1.0: USB hub found
- [ 7.016181] hub 2-0:1.0: 1 port detected
- [ 7.037001] usbcore: registered new interface driver usb-storage
- [ 7.050591] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 7.076052] init: - preinit -
- [ 7.390047] usb 1-1: new high-speed USB device number 2 using ehci-platform
- [ 7.866238] random: procd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
- [ 7.885410] usb-storage 1-1:1.0: USB Mass Storage device detected
- [ 7.914586] scsi host0: usb-storage 1-1:1.0
- [ 8.352969] rt3050-esw 10110000.esw: link changed 0x00
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 8.923728] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Fit 1.00 PQ: 0 ANSI: 6
- [ 8.945918] sd 0:0:0:0: [sda] 62521344 512-byte logical blocks: (32.0 GB/29.8 GiB)
- [ 8.963706] sd 0:0:0:0: [sda] Write Protect is off
- [ 8.974974] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
- [ 9.004703] sda: sda1
- [ 9.017355] sd 0:0:0:0: [sda] Attached SCSI removable disk
- [ 10.123908] rt3050-esw 10110000.esw: link changed 0x01
- [ 11.907743] mount_root: loading kmods from internal overlay
- [ 11.966097] kmodloader: loading kernel modules from //etc/modules-boot.d/*
- [ 11.984123] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
- [ 14.438972] jffs2: notice: (378) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 14.471196] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
- [ 14.498296] block: extroot: not configured
- [ 14.575400] jffs2: notice: (375) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 16.373409] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
- [ 16.400545] block: extroot: not configured
- [ 16.411277] mount_root: switching to jffs2 overlay
- [ 16.433413] urandom-seed: Seed file not found (/etc/urandom.seed)
- [ 16.650352] procd: - early -
- [ 16.656539] procd: - watchdog -
- [ 17.568614] procd: - ubus -
- [ 17.728114] random: ubusd: uninitialized urandom read (4 bytes read, 80 bits of entropy available)
- [ 17.747977] random: ubusd: uninitialized urandom read (4 bytes read, 80 bits of entropy available)
- [ 17.767024] random: ubusd: uninitialized urandom read (4 bytes read, 80 bits of entropy available)
- [ 17.788476] random: ubusd: uninitialized urandom read (4 bytes read, 82 bits of entropy available)
- [ 17.807606] random: ubusd: uninitialized urandom read (4 bytes read, 83 bits of entropy available)
- [ 17.829109] random: ubusd: uninitialized urandom read (4 bytes read, 83 bits of entropy available)
- [ 17.849225] random: ubusd: uninitialized urandom read (4 bytes read, 84 bits of entropy available)
- [ 17.870656] procd: - init -
- Please press Enter to activate this console.
- [ 19.019308] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 19.167486] loop: module loaded
- [ 19.194403] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 19.250932] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
- [ 19.267102] Backport generated by backports.git backports-20160324-13-g24da7d3c
- [ 19.380290] batman_adv: B.A.T.M.A.N. advanced 2016.5 (compatibility version 15) loaded
- [ 19.409336] Bridge firewalling registered
- [ 19.436522] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 19.536688] random: nonblocking pool is initialized
- [ 19.572758] nf_conntrack version 0.5.0 (450 buckets, 1800 max)
- [ 19.750786] xt_time: kernel timezone is -0000
- [ 19.835385] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
- [ 19.850004] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected
- [ 19.865575] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected
- [ 19.902011] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 25.250914] rt3050-esw 10110000.esw: link changed 0x00
- [ 27.610831] rt3050-esw 10110000.esw: link changed 0x01
- [ 27.654493] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
- [ 28.056983] Adding 32764k swap on /mnt/usb/external_fs/OpenWRT.swap. Priority:-1 extents:1 across:32764k
- [ 28.183742] EXT4-fs (loop0): couldn't mount as ext3 due to feature incompatibilities
- [ 28.244669] EXT4-fs (loop0): couldn't mount as ext2 due to feature incompatibilities
- [ 28.372951] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null)
- [ 31.972279] device eth0 entered promiscuous mode
- [ 32.029456] br-lan: port 1(eth0) entered forwarding state
- [ 32.040458] br-lan: port 1(eth0) entered forwarding state
- [ 34.031559] br-lan: port 1(eth0) entered forwarding state
- [ 36.602561] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 36.640296] device wlan0 entered promiscuous mode
- [ 36.692741] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- [ 36.705920] br-lan: port 2(wlan0) entered forwarding state
- [ 36.717084] br-lan: port 2(wlan0) entered forwarding state
- [ 38.711468] br-lan: port 2(wlan0) entered forwarding state
- [ 151.311489] usb 1-1: reset high-speed USB device number 2 using ehci-platform
- [ 235.487355] br-lan: port 2(wlan0) entered disabled state
- [ 235.498222] br-lan: port 1(eth0) entered disabled state
- [ 235.993500] device eth0 left promiscuous mode
- [ 236.002502] br-lan: port 1(eth0) entered disabled state
- [ 236.032886] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
- [ 236.044920] device wlan0 left promiscuous mode
- [ 236.054095] br-lan: port 2(wlan0) entered disabled state
- [ 240.407150] reboot: Restarting system
- U-Boot 1.1.7 (Dec 13 2011 - 13:49:42)
- Board: Ralink APSoC DRAM: 32 MB
- relocate_code Pointer at: 81fb4000
- ******************************
- Software System Reset Occurred
- ******************************
- spi_wait_nsec: 42
- spi device id: 7f 9d 46 7f 9d (9d467f9d)
- Warning: un-recognized chip ID, please update bootloader!
- raspi_read: from:30000 len:1000
- .*** Warning - bad CRC, using default environment
- ============================================
- Ralink UBoot Version: 3.6.0.0
- --------------------------------------------
- ASIC 5350_MP (Port5<->None)
- DRAM_CONF_FROM: Boot-Strapping
- DRAM_TYPE: SDRAM
- DRAM_SIZE: 256 Mbits
- DRAM_WIDTH: 16 bits
- DRAM_TOTAL_WIDTH: 16 bits
- TOTAL_MEMORY_SIZE: 32 MBytes
- Flash component: SPI Flash
- Date:Dec 13 2011 Time:13:49:42
- ============================================
- icache: sets:256, ways:4, linesz:32 ,total:32768
- dcache: sets:128, ways:4, linesz:32 ,total:16384
- ##### The CPU freq = 360 MHZ ####
- estimate memory size =32 Mbytes
- raspi_read: from:40028 len:6
- .
- raspi_read: from:0 len:30004
- ....*************Is_update = 0 plat = 1**************
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 7: Load Boot Loader code then write to Flash via Serial.
- 9: Load Boot Loader code then write to Flash via TFTP.
- 1 0
- 3: System Boot system code via Flash.
- ## Booting image at bc050000 ...
- raspi_read: from:50000 len:40
- . Image Name: MIPS LEDE Linux-4.4.61
- Created: 2017-04-17 16:15:53 UTC
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 1158946 Bytes = 1.1 MB
- Load Address: 80000000
- Entry Point: 80000000
- raspi_read: from:50040 len:11af22
- .................. Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80000000) ...
- ## Giving linux memsize in MB, 32
- Starting kernel ...
- [ 0.000000] Linux version 4.4.61 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3102-0224e32) ) #0 Sat Apr 15 16:13:45 2017
- [ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
- [ 0.000000] MIPS: machine is A5-V11
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 02000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
- [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
- [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
- [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Writing ErrCtl register=00069b50
- [ 0.000000] Readback ErrCtl register=00069b50
- [ 0.000000] Memory: 28612K/32768K available (2888K kernel code, 136K rwdata, 356K rodata, 196K init, 196K bss, 4156K reserved, 0K cma-reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:256
- [ 0.000000] CPU Clock: 360MHz
- [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
- [ 0.000000] systick: running - mult: 214748, shift: 32
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 10618113593 ns
- [ 0.000015] sched_clock: 32 bits at 180MHz, resolution 5ns, wraps every 11930464253ns
- [ 0.015683] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
- [ 0.090885] pid_max: default: 32768 minimum: 301
- [ 0.100300] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.113376] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.136774] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.156350] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 0.168555] pinctrl core: initialized pinctrl subsystem
- [ 0.181389] NET: Registered protocol family 16
- [ 0.200336] Can't analyze schedule() prologue at 8000ac9c
- [ 0.242019] rt2880_gpio 10000600.gpio: registering 22 gpios
- [ 0.253147] rt2880_gpio 10000600.gpio: registering 22 irq handlers
- [ 0.265844] rt2880_gpio 10000660.gpio: registering 6 gpios
- [ 0.276782] rt2880_gpio 10000660.gpio: registering 6 irq handlers
- [ 0.291441] clocksource: Switched to clocksource MIPS
- [ 0.303715] NET: Registered protocol family 2
- [ 0.314349] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.328239] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.340822] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.353682] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.365299] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.378265] NET: Registered protocol family 1
- [ 0.397348] rt-timer 10000100.timer: maximum frequency is 3662Hz
- [ 0.410816] Crashlog allocated RAM at address 0x1f00000
- [ 0.456871] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.468464] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.494130] io scheduler noop registered
- [ 0.501906] io scheduler deadline registered (default)
- [ 0.512462] ralink-usb-phy usbphy: invalid resource
- [ 0.523555] gpio-export gpio_export: 2 gpio(s) exported
- [ 0.534361] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 0.553953] console [ttyS0] disabled
- [ 0.561001] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
- [ 0.580828] console [ttyS0] enabled
- [ 0.580828] console [ttyS0] enabled
- [ 0.594599] bootconsole [early0] disabled
- [ 0.594599] bootconsole [early0] disabled
- [ 0.626182] spi spi0.0: force spi mode3
- [ 0.634839] m25p80 spi0.0: pm25lq032 (4096 Kbytes)
- [ 0.644588] 4 ofpart partitions found on MTD device spi0.0
- [ 0.655572] Creating 4 MTD partitions on "spi0.0":
- [ 0.665183] 0x000000000000-0x000000030000 : "u-boot"
- [ 0.678813] 0x000000030000-0x000000040000 : "u-boot-env"
- [ 0.693554] 0x000000040000-0x000000050000 : "factory"
- [ 0.707646] 0x000000050000-0x000000400000 : "firmware"
- [ 1.014186] 2 uimage-fw partitions found on MTD device firmware
- [ 1.026122] 0x000000050000-0x00000016af62 : "kernel"
- [ 1.039327] 0x00000016af62-0x000000400000 : "rootfs"
- [ 1.053266] mtd: device 5 (rootfs) set to be root filesystem
- [ 1.064883] 1 squashfs-split partitions found on MTD device rootfs
- [ 1.077305] 0x0000003a3000-0x000000400000 : "rootfs_data"
- [ 1.098408] rt3050-esw 10110000.esw: link changed 0x00
- [ 1.112430] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
- [ 1.130072] rt2880_wdt 10000120.watchdog: Initialized
- [ 1.142985] NET: Registered protocol family 10
- [ 1.160153] NET: Registered protocol family 17
- [ 1.169371] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 1.194619] 8021q: 802.1Q VLAN Support v1.8
- [ 1.225085] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
- [ 1.241367] Freeing unused kernel memory: 196K (8034f000 - 80380000)
- [ 3.555257] init: Console is alive
- [ 3.562751] init: - watchdog -
- [ 6.436890] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 6.607865] usbcore: registered new interface driver usbfs
- [ 6.619250] usbcore: registered new interface driver hub
- [ 6.630240] usbcore: registered new device driver usb
- [ 6.708292] SCSI subsystem initialized
- [ 6.727500] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 6.743880] ehci-platform: EHCI generic platform driver
- [ 6.765069] phy phy-usbphy.0: remote usb device wakeup disabled
- [ 6.776946] phy phy-usbphy.0: UTMI 16bit 30MHz
- [ 6.785936] ehci-platform 101c0000.ehci: EHCI Host Controller
- [ 6.797559] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
- [ 6.813708] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
- [ 6.841573] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
- [ 6.856415] hub 1-0:1.0: USB hub found
- [ 6.865124] hub 1-0:1.0: 1 port detected
- [ 6.878685] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 6.893930] ohci-platform: OHCI generic platform driver
- [ 6.904995] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
- [ 6.918777] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
- [ 6.934874] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
- [ 7.007555] hub 2-0:1.0: USB hub found
- [ 7.016181] hub 2-0:1.0: 1 port detected
- [ 7.037043] usbcore: registered new interface driver usb-storage
- [ 7.050627] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 7.076088] init: - preinit -
- [ 7.390075] usb 1-1: new high-speed USB device number 2 using ehci-platform
- [ 7.876241] random: procd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
- [ 7.895411] usb-storage 1-1:1.0: USB Mass Storage device detected
- [ 7.925059] scsi host0: usb-storage 1-1:1.0
- [ 8.356863] rt3050-esw 10110000.esw: link changed 0x00
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 8.933735] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Fit 1.00 PQ: 0 ANSI: 6
- [ 8.956572] sd 0:0:0:0: [sda] 62521344 512-byte logical blocks: (32.0 GB/29.8 GiB)
- [ 8.973863] sd 0:0:0:0: [sda] Write Protect is off
- [ 8.985235] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
- [ 9.014596] sda: sda1
- [ 9.027237] sd 0:0:0:0: [sda] Attached SCSI removable disk
- [ 10.504619] rt3050-esw 10110000.esw: link changed 0x01
- [ 11.912091] mount_root: loading kmods from internal overlay
- [ 11.969822] kmodloader: loading kernel modules from //etc/modules-boot.d/*
- [ 11.987781] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
- [ 14.428953] jffs2: notice: (377) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 14.461386] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
- [ 14.488302] block: extroot: not configured
- [ 14.553431] jffs2: notice: (374) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 16.345971] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
- [ 16.372996] block: extroot: not configured
- [ 16.383827] mount_root: switching to jffs2 overlay
- [ 16.405220] urandom-seed: Seed file not found (/etc/urandom.seed)
- [ 16.621774] procd: - early -
- [ 16.627812] procd: - watchdog -
- [ 17.540244] procd: - ubus -
- [ 17.698783] random: ubusd: uninitialized urandom read (4 bytes read, 81 bits of entropy available)
- [ 17.719203] random: ubusd: uninitialized urandom read (4 bytes read, 81 bits of entropy available)
- [ 17.737993] random: ubusd: uninitialized urandom read (4 bytes read, 81 bits of entropy available)
- [ 17.759193] random: ubusd: uninitialized urandom read (4 bytes read, 81 bits of entropy available)
- [ 17.777983] random: ubusd: uninitialized urandom read (4 bytes read, 81 bits of entropy available)
- [ 17.797536] random: ubusd: uninitialized urandom read (4 bytes read, 81 bits of entropy available)
- [ 17.819116] random: ubusd: uninitialized urandom read (4 bytes read, 84 bits of entropy available)
- [ 17.840806] procd: - init -
- Please press Enter to activate this console.
- [ 18.957956] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 19.500850] loop: module loaded
- [ 19.534389] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 19.588508] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
- [ 19.604638] Backport generated by backports.git backports-20160324-13-g24da7d3c
- [ 19.733924] batman_adv: B.A.T.M.A.N. advanced 2016.5 (compatibility version 15) loaded
- [ 19.768820] Bridge firewalling registered
- [ 19.796714] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 19.923028] nf_conntrack version 0.5.0 (450 buckets, 1800 max)
- [ 19.934917] random: nonblocking pool is initialized
- [ 20.143862] xt_time: kernel timezone is -0000
- [ 20.235186] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
- [ 20.249774] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected
- [ 20.265312] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected
- [ 20.304896] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 25.499511] rt3050-esw 10110000.esw: link changed 0x00
- [ 27.457621] rt3050-esw 10110000.esw: link changed 0x01
- [ 27.754859] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
- [ 28.215709] Adding 32764k swap on /mnt/usb/external_fs/OpenWRT.swap. Priority:-1 extents:1 across:32764k
- [ 28.363592] EXT4-fs (loop0): couldn't mount as ext3 due to feature incompatibilities
- [ 28.404575] EXT4-fs (loop0): couldn't mount as ext2 due to feature incompatibilities
- [ 28.534744] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null)
- [ 32.233315] device eth0 entered promiscuous mode
- [ 32.264877] br-lan: port 1(eth0) entered forwarding state
- [ 32.275876] br-lan: port 1(eth0) entered forwarding state
- [ 34.271544] br-lan: port 1(eth0) entered forwarding state
- [ 36.826935] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 36.870334] device wlan0 entered promiscuous mode
- [ 36.915353] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- [ 36.928514] br-lan: port 2(wlan0) entered forwarding state
- [ 36.939679] br-lan: port 2(wlan0) entered forwarding state
- [ 38.931469] br-lan: port 2(wlan0) entered forwarding state
- [ 105.311534] usb 1-1: reset high-speed USB device number 2 using ehci-platform
- [ 114.734823] br-lan: port 2(wlan0) entered disabled state
- [ 114.745699] br-lan: port 1(eth0) entered disabled state
- [ 114.784937] device eth0 left promiscuous mode
- [ 114.793970] br-lan: port 1(eth0) entered disabled state
- [ 114.826255] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
- [ 114.838337] device wlan0 left promiscuous mode
- [ 114.847549] br-lan: port 2(wlan0) entered disabled state
- [ 119.405292] reboot: Restarting system
- U-Boot 1.1.7 (Dec 13 2011 - 13:49:42)
- Board: Ralink APSoC DRAM: 32 MB
- relocate_code Pointer at: 81fb4000
- ******************************
- Software System Reset Occurred
- ******************************
- spi_wait_nsec: 42
- spi device id: 7f 9d 46 7f 9d (9d467f9d)
- Warning: un-recognized chip ID, please update bootloader!
- raspi_read: from:30000 len:1000
- .*** Warning - bad CRC, using default environment
- ============================================
- Ralink UBoot Version: 3.6.0.0
- --------------------------------------------
- ASIC 5350_MP (Port5<->None)
- DRAM_CONF_FROM: Boot-Strapping
- DRAM_TYPE: SDRAM
- DRAM_SIZE: 256 Mbits
- DRAM_WIDTH: 16 bits
- DRAM_TOTAL_WIDTH: 16 bits
- TOTAL_MEMORY_SIZE: 32 MBytes
- Flash component: SPI Flash
- Date:Dec 13 2011 Time:13:49:42
- ============================================
- icache: sets:256, ways:4, linesz:32 ,total:32768
- dcache: sets:128, ways:4, linesz:32 ,total:16384
- ##### The CPU freq = 360 MHZ ####
- estimate memory size =32 Mbytes
- raspi_read: from:40028 len:6
- .
- raspi_read: from:0 len:30004
- ....*************Is_update = 0 plat = 1**************
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 7: Load Boot Loader code then write to Flash via Serial.
- 9: Load Boot Loader code then write to Flash via TFTP.
- 1 0
- 3: System Boot system code via Flash.
- ## Booting image at bc050000 ...
- raspi_read: from:50000 len:40
- . Image Name: MIPS LEDE Linux-4.4.61
- Created: 2017-04-17 16:15:53 UTC
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 1158946 Bytes = 1.1 MB
- Load Address: 80000000
- Entry Point: 80000000
- raspi_read: from:50040 len:11af22
- .................. Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80000000) ...
- ## Giving linux memsize in MB, 32
- Starting kernel ...
- [ 0.000000] Linux version 4.4.61 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3102-0224e32) ) #0 Sat Apr 15 16:13:45 2017
- [ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
- [ 0.000000] MIPS: machine is A5-V11
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 02000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
- [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
- [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
- [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
- [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Writing ErrCtl register=00069b50
- [ 0.000000] Readback ErrCtl register=00069b50
- [ 0.000000] Memory: 28612K/32768K available (2888K kernel code, 136K rwdata, 356K rodata, 196K init, 196K bss, 4156K reserved, 0K cma-reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:256
- [ 0.000000] CPU Clock: 360MHz
- [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
- [ 0.000000] systick: running - mult: 214748, shift: 32
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 10618113593 ns
- [ 0.000015] sched_clock: 32 bits at 180MHz, resolution 5ns, wraps every 11930464253ns
- [ 0.015682] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
- [ 0.090885] pid_max: default: 32768 minimum: 301
- [ 0.100300] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.113377] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.136776] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.156352] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 0.168557] pinctrl core: initialized pinctrl subsystem
- [ 0.181391] NET: Registered protocol family 16
- [ 0.200338] Can't analyze schedule() prologue at 8000ac9c
- [ 0.242017] rt2880_gpio 10000600.gpio: registering 22 gpios
- [ 0.253145] rt2880_gpio 10000600.gpio: registering 22 irq handlers
- [ 0.265840] rt2880_gpio 10000660.gpio: registering 6 gpios
- [ 0.276779] rt2880_gpio 10000660.gpio: registering 6 irq handlers
- [ 0.291439] clocksource: Switched to clocksource MIPS
- [ 0.303713] NET: Registered protocol family 2
- [ 0.314348] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.328238] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.340820] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.353680] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.365297] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.378263] NET: Registered protocol family 1
- [ 0.397344] rt-timer 10000100.timer: maximum frequency is 3662Hz
- [ 0.410813] Crashlog allocated RAM at address 0x1f00000
- [ 0.456877] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.468469] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.494144] io scheduler noop registered
- [ 0.501919] io scheduler deadline registered (default)
- [ 0.512476] ralink-usb-phy usbphy: invalid resource
- [ 0.523570] gpio-export gpio_export: 2 gpio(s) exported
- [ 0.534375] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 0.553967] console [ttyS0] disabled
- [ 0.561015] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
- [ 0.580842] console [ttyS0] enabled
- [ 0.580842] console [ttyS0] enabled
- [ 0.594613] bootconsole [early0] disabled
- [ 0.594613] bootconsole [early0] disabled
- [ 0.626202] spi spi0.0: force spi mode3
- [ 0.634859] m25p80 spi0.0: pm25lq032 (4096 Kbytes)
- [ 0.644609] 4 ofpart partitions found on MTD device spi0.0
- [ 0.655594] Creating 4 MTD partitions on "spi0.0":
- [ 0.665206] 0x000000000000-0x000000030000 : "u-boot"
- [ 0.678834] 0x000000030000-0x000000040000 : "u-boot-env"
- [ 0.693570] 0x000000040000-0x000000050000 : "factory"
- [ 0.707662] 0x000000050000-0x000000400000 : "firmware"
- [ 1.014207] 2 uimage-fw partitions found on MTD device firmware
- [ 1.026143] 0x000000050000-0x00000016af62 : "kernel"
- [ 1.039347] 0x00000016af62-0x000000400000 : "rootfs"
- [ 1.053284] mtd: device 5 (rootfs) set to be root filesystem
- [ 1.064902] 1 squashfs-split partitions found on MTD device rootfs
- [ 1.077323] 0x0000003a3000-0x000000400000 : "rootfs_data"
- [ 1.098410] rt3050-esw 10110000.esw: link changed 0x00
- [ 1.112433] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
- [ 1.130075] rt2880_wdt 10000120.watchdog: Initialized
- [ 1.142988] NET: Registered protocol family 10
- [ 1.160154] NET: Registered protocol family 17
- [ 1.169372] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 1.194621] 8021q: 802.1Q VLAN Support v1.8
- [ 1.225087] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
- [ 1.241369] Freeing unused kernel memory: 196K (8034f000 - 80380000)
- [ 3.555435] init: Console is alive
- [ 3.562928] init: - watchdog -
- [ 6.436519] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 6.607620] usbcore: registered new interface driver usbfs
- [ 6.619005] usbcore: registered new interface driver hub
- [ 6.629994] usbcore: registered new device driver usb
- [ 6.707206] SCSI subsystem initialized
- [ 6.726399] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 6.742748] ehci-platform: EHCI generic platform driver
- [ 6.763937] phy phy-usbphy.0: remote usb device wakeup disabled
- [ 6.775815] phy phy-usbphy.0: UTMI 16bit 30MHz
- [ 6.784803] ehci-platform 101c0000.ehci: EHCI Host Controller
- [ 6.796424] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
- [ 6.812570] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
- [ 6.841574] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
- [ 6.856418] hub 1-0:1.0: USB hub found
- [ 6.865120] hub 1-0:1.0: 1 port detected
- [ 6.878659] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 6.893891] ohci-platform: OHCI generic platform driver
- [ 6.904953] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
- [ 6.918734] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
- [ 6.934833] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
- [ 7.007555] hub 2-0:1.0: USB hub found
- [ 7.016177] hub 2-0:1.0: 1 port detected
- [ 7.037048] usbcore: registered new interface driver usb-storage
- [ 7.050616] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 7.076082] init: - preinit -
- [ 7.390049] usb 1-1: new high-speed USB device number 2 using ehci-platform
- [ 7.885540] random: procd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
- [ 7.904725] usb-storage 1-1:1.0: USB Mass Storage device detected
- [ 7.951730] scsi host0: usb-storage 1-1:1.0
- [ 8.355926] rt3050-esw 10110000.esw: link changed 0x00
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 8.953726] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Fit 1.00 PQ: 0 ANSI: 6
- [ 8.976165] sd 0:0:0:0: [sda] 62521344 512-byte logical blocks: (32.0 GB/29.8 GiB)
- [ 8.993813] sd 0:0:0:0: [sda] Write Protect is off
- [ 9.005098] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
- [ 9.034835] sda: sda1
- [ 9.047476] sd 0:0:0:0: [sda] Attached SCSI removable disk
- [ 10.487311] rt3050-esw 10110000.esw: link changed 0x01
- [ 11.902203] mount_root: loading kmods from internal overlay
- [ 11.959966] kmodloader: loading kernel modules from //etc/modules-boot.d/*
- [ 11.977776] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
- [ 14.413806] jffs2: notice: (377) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 14.445995] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
- [ 14.472177] block: extroot: not configured
- [ 14.531791] jffs2: notice: (374) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 16.324464] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
- [ 16.350538] block: extroot: not configured
- [ 16.361052] mount_root: switching to jffs2 overlay
- [ 16.382783] urandom-seed: Seed file not found (/etc/urandom.seed)
- [ 16.598615] procd: - early -
- [ 16.604806] procd: - watchdog -
- [ 17.518631] procd: - ubus -
- [ 17.678762] random: ubusd: uninitialized urandom read (4 bytes read, 79 bits of entropy available)
- [ 17.699677] random: ubusd: uninitialized urandom read (4 bytes read, 80 bits of entropy available)
- [ 17.719098] random: ubusd: uninitialized urandom read (4 bytes read, 80 bits of entropy available)
- [ 17.739575] random: ubusd: uninitialized urandom read (4 bytes read, 80 bits of entropy available)
- [ 17.758107] random: ubusd: uninitialized urandom read (4 bytes read, 81 bits of entropy available)
- [ 17.778526] random: ubusd: uninitialized urandom read (4 bytes read, 81 bits of entropy available)
- [ 17.798132] random: ubusd: uninitialized urandom read (4 bytes read, 81 bits of entropy available)
- [ 17.818892] procd: - init -
- Please press Enter to activate this console.
- [ 18.952814] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 19.502442] loop: module loaded
- [ 19.534550] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 19.588470] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
- [ 19.604600] Backport generated by backports.git backports-20160324-13-g24da7d3c
- [ 19.735223] batman_adv: B.A.T.M.A.N. advanced 2016.5 (compatibility version 15) loaded
- [ 19.768842] Bridge firewalling registered
- [ 19.796909] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 19.915371] nf_conntrack version 0.5.0 (450 buckets, 1800 max)
- [ 20.098053] xt_time: kernel timezone is -0000
- [ 20.146255] random: nonblocking pool is initialized
- [ 20.190958] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
- [ 20.205588] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected
- [ 20.221167] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected
- [ 20.256528] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 25.344800] rt3050-esw 10110000.esw: link changed 0x00
- [ 27.524075] rt3050-esw 10110000.esw: link changed 0x01
- [ 28.054358] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
- [ 28.446831] Adding 32764k swap on /mnt/usb/external_fs/OpenWRT.swap. Priority:-1 extents:1 across:32764k
- [ 28.583640] EXT4-fs (loop0): couldn't mount as ext3 due to feature incompatibilities
- [ 28.634788] EXT4-fs (loop0): couldn't mount as ext2 due to feature incompatibilities
- [ 28.759276] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null)
- [ 32.444624] device eth0 entered promiscuous mode
- [ 32.490723] br-lan: port 1(eth0) entered forwarding state
- [ 32.501726] br-lan: port 1(eth0) entered forwarding state
- [ 34.501562] br-lan: port 1(eth0) entered forwarding state
- [ 36.982231] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 37.025823] device wlan0 entered promiscuous mode
- [ 37.076977] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- [ 37.090152] br-lan: port 2(wlan0) entered forwarding state
- [ 37.101318] br-lan: port 2(wlan0) entered forwarding state
- [ 39.091453] br-lan: port 2(wlan0) entered forwarding state
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement