API tools faq
paste
Advertisement
Guest User

Untitled

a guest
Jan 27th, 2012
549
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 9.01 KB | None | 0 0
raw download clone embed print report
  1. RouterBOOT booter 2.26
  2.  
  3. RouterBoard 411
  4.  
  5. CPU frequency: 300 MHz
  6. Memory size: 32 MB
  7.  
  8. Press any key within 2 seconds to enter setup..
  9. kernel not found
  10. trying dhcp protocol... OK
  11. resolved mac address 6C:62:6D:2B:81:1F
  12. transfer started ................................... transfer ok, time=2.04s
  13. setting up elf image... OK
  14. jumping to kernel code
  15. [ 0.000000] Linux version 2.6.39.4 (nop@blackbox) (gcc version 4.5.4 20120105 (prerelease) (Linaro GCC 4.5-2012.01) ) #1 Thu Jan 26 18:45:02 VOLT 2012
  16. [ 0.000000] bootconsole [early0] enabled
  17. [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
  18. [ 0.000000] SoC: Atheros AR7130 rev 2
  19. [ 0.000000] Clocks: CPU:300.000MHz, DDR:300.000MHz, AHB:150.000MHz, Ref:40.000MHz
  20. [ 0.000000] Determined physical RAM map:
  21. [ 0.000000] memory: 02000000 @ 00000000 (usable)
  22. [ 0.000000] User-defined physical RAM map:
  23. [ 0.000000] memory: 02000000 @ 00000000 (usable)
  24. [ 0.000000] Initrd not found or empty - disabling initrd
  25. [ 0.000000] Zone PFN ranges:
  26. [ 0.000000] Normal 0x00000000 -> 0x00002000
  27. [ 0.000000] Movable zone start PFN for each node
  28. [ 0.000000] early_node_map[1] active PFN ranges
  29. [ 0.000000] 0: 0x00000000 -> 0x00002000
  30. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
  31. [ 0.000000] Kernel command line: console=ttyS0,115200 gpio=4031 HZ=150000000 mem=32M kmac=00:0C:42:24:E7:5F board=411 boot=1 mlc=2 rootfstype=squashfs,yaffs,jffs2 noinitrd
  32. [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
  33. [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
  34. [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
  35. [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  36. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  37. [ 0.000000] Writing ErrCtl register=00000000
  38. [ 0.000000] Readback ErrCtl register=00000000
  39. [ 0.000000] Memory: 27456k/32768k available (2146k kernel code, 5312k reserved, 438k data, 1908k init, 0k highmem)
  40. [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  41. [ 0.000000] NR_IRQS:80
  42. [ 0.000000] Calibrating delay loop... 199.06 BogoMIPS (lpj=995328)
  43. [ 0.080000] pid_max: default: 32768 minimum: 301
  44. [ 0.080000] Mount-cache hash table entries: 512
  45. [ 0.090000] NET: Registered protocol family 16
  46. [ 0.100000] MIPS: machine is MikroTik RouterBOARD 411/A/AH
  47. [ 0.600000] registering PCI controller with io_map_base unset
  48. [ 0.610000] bio: create slab <bio-0> at 0
  49. [ 0.620000] pci 0000:00:12.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
  50. [ 0.630000] pci 0000:00:12.0: BAR 0: set to [mem 0x10000000-0x1000ffff] (PCI address [0x10000000-0x1000ffff])
  51. [ 0.630000] PCI: mapping irq 72 to pin1@0000:00:12.0
  52. [ 0.640000] Switching to clocksource MIPS
  53. [ 0.640000] NET: Registered protocol family 2
  54. [ 0.650000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  55. [ 0.650000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
  56. [ 0.660000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  57. [ 0.660000] TCP: Hash tables configured (established 1024 bind 1024)
  58. [ 0.670000] TCP reno registered
  59. [ 0.670000] UDP hash table entries: 256 (order: 0, 4096 bytes)
  60. [ 0.680000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  61. [ 0.690000] NET: Registered protocol family 1
  62. [ 5.270000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  63. [ 5.280000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  64. [ 5.290000] msgmni has been set to 53
  65. [ 5.290000] io scheduler noop registered
  66. [ 5.300000] io scheduler deadline registered (default)
  67. [ 5.300000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
  68. [ 5.330000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
  69. [ 5.340000] console [ttyS0] enabled, bootconsole disabled
  70. [ 5.340000] console [ttyS0] enabled, bootconsole disabled
  71. [ 5.350000] Atheros AR71xx SPI Controller driver version 0.2.4
  72. [ 5.360000] m25p80 spi0.0: pm25lv512 (64 Kbytes)
  73. [ 5.360000] Creating 4 MTD partitions on "spi0.0":
  74. [ 5.370000] 0x000000000000-0x00000000b000 : "routerboot"
  75. [ 5.380000] 0x00000000b000-0x00000000c000 : "hard_config"
  76. [ 5.380000] 0x00000000d000-0x00000000f000 : "bios"
  77. [ 5.390000] 0x00000000f000-0x000000010000 : "soft_config"
  78. [ 5.400000] NAND flash driver for RouterBoard 4xx series version 0.2.0
  79. [ 5.410000] NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
  80. [ 5.410000] Scanning device for bad blocks
  81. [ 5.590000] Bad eraseblock 817 at 0x000000cc4000
  82. [ 5.860000] Bad eraseblock 2055 at 0x00000201c000
  83. [ 6.020000] Bad eraseblock 2817 at 0x000002c04000
  84. [ 6.300000] Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
  85. [ 6.300000] 0x000000000000-0x000000040000 : "booter"
  86. [ 6.310000] 0x000000040000-0x000000600000 : "kernel"
  87. [ 6.320000] 0x000000600000-0x000004000000 : "rootfs"
  88. [ 6.330000] mtd: partition "rootfs" set to be root filesystem
  89. [ 6.330000] split_squashfs: no squashfs found in "NAND 64MiB 3,3V 8-bit"
  90. [ 6.350000] ag71xx_mdio: probed
  91. [ 6.350000] eth0: Atheros AG71xx at 0xb9000000, irq 4
  92. [ 6.660000] Atheros AR71xx hardware watchdog driver version 0.1.0
  93. [ 6.660000] TCP westwood registered
  94. [ 6.670000] NET: Registered protocol family 17
  95. [ 6.670000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  96. [ 6.680000] All bugs added by David S. Miller <davem@redhat.com>
  97. [ 6.700000] Freeing unused kernel memory: 1908k freed
  98. [ 7.580000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
  99. [ 7.610000] Button Hotplug driver version 0.4.1
  100. - preinit -
  101. Press the [f] key and hit [enter] to enter failsafe mode
  102. [ 8.660000] eth0: link up (100Mbps/Full duplex)
  103. - regular preinit -
  104. [ 10.900000] eth0: link down
  105. - init -
  106. [ 11.330000] Compat-wireless backport release: compat-wireless-2011-11-29
  107. [ 11.340000] Backport based on wireless-testing.git master-2011-12-01
  108. [ 11.490000] cfg80211: Calling CRDA to update world regulatory domain
  109. [ 11.890000] NET: Registered protocol family 10
  110. [ 11.900000] cfg80211: World regulatory domain updated:
  111. [ 11.910000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  112. [ 11.920000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  113. [ 11.920000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  114. [ 11.930000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  115. [ 11.940000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  116. [ 11.950000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  117. [ 12.370000] PCI: Enabling device 0000:00:12.0 (0000 -> 0002)
  118. [ 12.380000] ath5k 0000:00:12.0: registered as 'phy0'
  119. [ 13.010000] ath5k phy0: Atheros AR5414 chip found (MAC: 0xa5, PHY: 0x61)
  120. [ 13.020000] cfg80211: Calling CRDA for country: US
  121. [ 13.220000] cfg80211: Regulatory domain changed to country: US
  122. [ 13.230000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  123. [ 13.240000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
  124. [ 13.240000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
  125. [ 13.250000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  126. [ 13.260000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  127. [ 13.270000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  128. [ 13.280000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
  129. [ 13.540000] PPP generic driver version 2.4.2
  130. [ 14.140000] tun: Universal TUN/TAP device driver, 1.6
  131. [ 14.150000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  132. [ 14.280000] IPv4 over IPv4 tunneling driver
  133. [ 14.320000] IPv6 over IPv4 tunneling driver
  134. [ 14.520000] GRE over IPv4 demultiplexor driver
  135. [ 14.570000] GRE over IPv4 tunneling driver
  136. [ 14.690000] ip_tables: (C) 2000-2006 Netfilter Core Team
  137. [ 14.890000] NET: Registered protocol family 24
  138. [ 15.060000] nf_conntrack version 0.5.0 (458 buckets, 1832 max)
  139. [ 15.560000] ip6_tables: (C) 2000-2006 Netfilter Core Team
  140.  
  141. Please press Enter to activate this console. [ 17.700000] ADDRCONF(NETDEV_UP): eth0: link is not ready
  142. [ 18.040000] device eth0 entered promiscuous mode
  143. [ 18.050000] eth0: link up (100Mbps/Full duplex)
  144. [ 18.050000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  145. [ 18.100000] br-lan: port 1(eth0) entering forwarding state
  146. [ 18.100000] br-lan: port 1(eth0) entering forwarding state
  147. [ 20.980000] device eth0 left promiscuous mode
  148. [ 20.990000] br-lan: port 1(eth0) entering forwarding state
  149. [ 21.490000] device eth0 entered promiscuous mode
  150. [ 21.500000] br-lan: port 1(eth0) entering forwarding state
  151. [ 21.500000] br-lan: port 1(eth0) entering forwarding state
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!