AP99 (ar7241 - Virian) U-boot
DRAM:
sri
ar7240_ddr_initial_config(133): virian ddr1 init
#### TAP VALUE 1 = 0xf, 2 = 0x10 [0x0: 0x1f]
32 MB
id read 0x100000ff
sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
Virian MDC CFG Value ==> 4
: cfg1 0xf cfg2 0x7014
eth0: 00:03:7f:09:0b:ad
eth0 up
Virian MDC CFG Value ==> 4
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Autobooting in 1 seconds
ar7240> setenv ipaddr 192.168.0.160
ar7240> setenv serverip 192.168.0.10
ar7240> tftp # ath0 hint - pcie slot 0
Usage:
tftpboot- boot image via network using TFTP protocol

ar7240> h_fixup_size=4096
Unknown command 'h_fixup_size=4096' - try 'help'
ar7240> irmware"
Unknown command 'irmware"' - try 'help'
ar7240> tftp 0x80050000 /mr/boot/kernel/kernel
dup 1 speed 1000
Using eth1 device
TFTP from server 192.168.0.10; our IP address is 192.168.0.160
Filename '/mr/boot/kernel/kernel'.
Load address: 0x80050000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ############################
done
Bytes transferred = 5797566 (5876be hex)
ar7240> go 0x80050100
## Starting application at 0x80050100 ...
CPU platform: Atheros AR7241 rev 1
CPU Frequency=400 MHz
CPU DDR Frequency=400 MHz
CPU AHB Frequency=200 MHz
platform frequency: 400000000
arguments:
  a0 = 00000001
  a1 = 81f87d24
  a2 = 00000010
  a3 = fffffffe
Cmd line:argv is invalid
Environment:
envp is invalid
Cache info:
  picache_stride    = 4096
  picache_loopcount = 16
  pdcache_stride    = 4096
  pdcache_loopcount = 8
cpu0: MIPS Technologies processor v116.147
  MMU: Standard TLB, 16 entries
  L1 i-cache: 4 ways of 512 sets, 32 bytes per line
  L1 d-cache: 4 ways of 256 sets, 32 bytes per line
  Config1=0x9ee3519e<PerfCount,WatchRegs,MIPS16,EJTAG>
  Config3=0x20
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.0-CURRENT #135 r240866:241032M: Fri Sep 28 15:52:56 BRT 2012
    root@server01:/data/mr3220-aonet/obj/mips.mips/data/mr3220-aonet/src/sys/TP-MR3220 mips
WARNING: WITNESS option enabled, expect reduced performance.
MEMGUARD DEBUGGING ALLOCATOR INITIALIZED:
        MEMGUARD map base: 0xc0400000
        MEMGUARD map limit: 0xc34dc000
        MEMGUARD map size: 50032 KBytes
real memory  = 33554432 (32768K bytes)
avail memory = 25079808 (23MB)
random device not loaded; using insecure entropy
nexus0: <MIPS32 root nexus>
clock0: <Generic MIPS32 ticker> on nexus0
Timecounter "MIPS32" frequency 200000000 Hz quality 800
Event timer "MIPS32" frequency 200000000 Hz quality 800
argemdio0: <Atheros AR71xx built-in ethernet interface, MDIO controller> at mem 0x1a000000-0x1a000fff on nexus0
mdio0: <MDIO> on argemdio0
mdioproxy_identify: called: dev: mdio0
mdioproxy0: <MII/MDIO proxy, MDIO side> on mdio0
mdioproxy_attach: called mdio
rendevous_register_target: called: dev: mdioproxy0
rendevous_register_target: sizeof: 28
arswitch0: <Atheros AR7240 Integrated Ethernet Switch> on mdio0
miibus0: <MII bus> on arswitch0
ukphy0: <Generic IEEE 802.3u media interface> PHY 0 on miibus0
ukphy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus1: <MII bus> on arswitch0
ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus1
ukphy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus2: <MII bus> on arswitch0
ukphy2: <Generic IEEE 802.3u media interface> PHY 2 on miibus2
ukphy2:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus3: <MII bus> on arswitch0
ukphy3: <Generic IEEE 802.3u media interface> PHY 3 on miibus3
ukphy3:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
etherswitch0: <Switch controller> on arswitch0
mdio1: <MDIO> on arswitch0
mdioproxy_identify: called: dev: mdio1
mdioproxy1: <MII/MDIO proxy, MDIO side> on mdio1
mdioproxy_attach: called mdio
rendevous_register_target: called: dev: mdioproxy1
rendevous_register_target: sizeof: 28
apb0 at irq 4 on nexus0
uart0: <16550 or compatible> on apb0
uart0: console (115200,n,8,1)
gpio0: <Atheros AR71XX GPIO driver> on apb0
gpio0: [GIANT-LOCKED]
gpio0: gpio pinmask=0x1943
gpioc0: <GPIO controller> on gpio0
gpiobus0: <GPIO bus> on gpio0
gpioled0: <GPIO led> at pin(s) 0 on gpiobus0
gpioled1: <GPIO led> at pin(s) 1 on gpiobus0
gpioled2: <GPIO led> at pin(s) 8 on gpiobus0
ehci0: <AR71XX Integrated USB 2.0 controller> at mem 0x1b000100-0x1c0000ff irq 1 on nexus0
usbus0: set host controller mode
usbus0: EHCI version 1.0
usbus0: set host controller mode
usbus0 on ehci0
pcib0 at irq 0 on nexus0
pcib0: found EEPROM at 0x1fff1000 on 0.0.0
pcib0: EEPROM firmware: 0x1fff1000 @ 4096 bytes
pcib0: device EEPROM 'pcib.0.bus.0.0.0.eeprom_firmware' registered
pci0: <PCI bus> on pcib0
ath0: <Atheros 9285> at device 0.0 on pci0
ath0: ath_pci_attach: EEPROM firmware @ 0xc3524000
ath0: [HT] enabling HT modes
ath0: [HT] 1 RX streams; 1 TX streams
ath0: AR9285 mac 192.2 RF5133 phy 14.0
ath0: 2GHz radio: 0x0000; 5GHz radio: 0x00c0
arge0: <Atheros AR71xx built-in ethernet interface> at mem 0x19000000-0x19000fff irq 2 on nexus0
arge0: Overriding MAC from EEPROM
mii_attach_proxy: called arge0
miiproxy0: <MII/MDIO proxy, MII side> on arge0
miiproxy_attach: called: dev: miiproxy0
rendevous_register_proxy: called: name :mdioproxy1 dev: miiproxy0
rendevous_attach: called
miiproxy_rendevous_callback: mdio1
miiproxy0: attached to target mdio1
arge0: finishing attachment, phymask 0010, proxy set
miibus4: <MII bus> on miiproxy0
ukphy4: <Generic IEEE 802.3u media interface> PHY 4 on miibus4
ukphy4:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
arge0: Ethernet address: 90:f6:52:67:d2:10
arge1: <Atheros AR71xx built-in ethernet interface> at mem 0x1a000000-0x1a000fff irq 3 on nexus0
mii_attach_proxy: called arge1
arge1: finishing attachment, phymask 0000, proxy null
arge1: Ethernet address: 90:f6:52:67:d2:11
spi0: <AR71XX SPI> at mem 0x1f000000-0x1f00000f on nexus0
spibus0: <spibus bus> on spi0
mx25l0: <M25Pxx Flash Family> at cs 0 on spibus0
mx25l0: w25q32, sector 65536 bytes, 64 sectors
ar71xx_wdog0: <Atheros AR71XX watchdog timer> on nexus0
ar71xx_wdog0: Previous reset was due to watchdog timeout
Timecounters tick every 1.000 msec
arswitch0port1: link state changed to DOWN
arswitch0port2: link state changed to DOWN
arswitch0port3: link state changed to DOWN
arswitch0port4: link state changed to DOWN
usbus0: 480Mbps High Speed USB v2.0
ugen0.1: <Atheros> at usbus0
uhub0: <Atheros EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
bootpc_init: wired to interface 'arge0'
Sending DHCP Discover packet from interface arge0 (90:f6:52:67:d2:10)
arge0: link state changed to DOWN
uhub0: 1 port with 1 removable, self powered
arswitch0port1: link state changed to UP
ugen0.2: <vendor 0x1a40> at usbus0
uhub1: <vendor 0x1a40 USB 2.0 Hub MTT, class 9/0, rev 2.00/1.00, addr 2> on usbus0
uhub1: MTT enabled
arge0: link state changed to UP
uhub1: 4 ports with 4 removable, self powered
Received DHCP Offer packet on arge0 from 192.168.0.10 (accepted) (no root path)
Received DHCP Offer packet on arge0 from 192.168.0.10 (ignored) (no root path)
Received DHCP Offer packet on arge0 from 192.168.0.10 (ignored) (no root path)
ugen0.3: <hp> at usbus0
umass0: <hp v165w, class 0/0, rev 2.00/10.00, addr 3> on usbus0
umass0:  SCSI over Bulk-Only; quirks = 0x0100
umass0:0:0:-1: Attached to scbus0
da0 at umass-sim0 bus 0 scbus0 target 0 lun 0
da0: <hp v165w 1.00> Removable Direct Access SCSI-4 device
da0: 40.000MB/s transfers
da0: 7650MB (15667200 512 byte sectors: 255H 63S/T 975C)
Sending DHCP Request packet from interface arge0 (90:f6:52:67:d2:10)
Received DHCP Ack packet on arge0 from 192.168.0.10 (accepted) (got root path)
ugen0.4: <SanDisk> at usbus0
umass1: <SanDisk Cruzer Blade, class 0/0, rev 2.00/1.00, addr 4> on usbus0
umass1:  SCSI over Bulk-Only; quirks = 0x4100
umass1:1:1:-1: Attached to scbus1
da1 at umass-sim1 bus 1 scbus1 target 0 lun 0
da1: <SanDisk Cruzer Blade 1.00> Removable Direct Access SCSI-2 device
da1: 40.000MB/s transfers
da1: 3827MB (7837696 512 byte sectors: 255H 63S/T 487C)
ugen0.5: <SanDisk> at usbus0
umass2: <SanDisk Cruzer Blade, class 0/0, rev 2.00/1.00, addr 5> on usbus0
umass2:  SCSI over Bulk-Only; quirks = 0x4100
umass2:2:2:-1: Attached to scbus2
da2 at umass-sim2 bus 2 scbus2 target 0 lun 0
da2: <SanDisk Cruzer Blade 1.00> Removable Direct Access SCSI-2 device
da2: 40.000MB/s transfers
da2: 3827MB (7837696 512 byte sectors: 255H 63S/T 487C)
arge0 at 192.168.0.160 server 192.168.0.10 boot file /mr/boot/kernel/kernel
subnet mask 255.255.255.0 router 192.168.0.1 rootfs 192.168.0.10:/data/mr3220-aonet/nfsroot
Adjusted interface arge0
WARNING: WITNESS option enabled, expect reduced performance.
Trying to mount root from nfs: []...
NFS ROOT: 192.168.0.10:/data/mr3220-aonet/nfsroot
warning: no time-of-day clock registered, system time will not be set accurately
warning: no time-of-day clock registered, system time will not be set accurately
Interface arge0 IP-Address 192.168.0.160 Broadcast 192.168.0.255
Setting hostuuid: 1c538f4d-1dd2-11b2-842d-90f65267d210.
Setting hostid: 0x5d9891a9.
No suitable dump device was found.
Entropy harvesting:.
Starting file system checks:
mount_nfs: can't update /var/db/mounttab for 192.168.0.10:/data/mr3220-aonet/nfsroot
Mounting local file systems:.
Adding /usr/swap.00 as additional swap
Writing entropy file:.
Setting hostname: mr3220.
Starting Network: lo0.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
        options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
        inet 127.0.0.1 netmask 0xff000000
Starting devd.
devd: cannot open pid file: Operation not supported
Creating and/or trimming log files.
Starting syslogd.
syslogd: cannot open pid file: Operation not supported
realpath: /dev/dumpdev: No such file or directory
/etc/rc: WARNING: Dump device does not exist.  Savecore not run.
ELF ldconfig path: /lib /usr/lib /usr/lib/compat
Starting rpcbind.
Jan  1 00:00:39 mr3220 rpcbind: cannot create socket for udp6
Clearing /tmp (X related).
Starting statd.
Starting lockd.
Can't find or load kernel support for rpc.lockd - using non-kernel implementation
Updating motd:.
Starting ntpd.
PRNG is not seeded
PRNG is not seeded
PRNG is not seeded
PRNG is not seeded
Performing sanity check on sshd configuration.
PRNG is not seeded
/etc/rc: WARNING: failed precmd routine for sshd
Starting cron.

Thu Jan  1 00:00:50 UTC 1970

FreeBSD/mips (mr3220) (ttyu0)

login: