Lexar USB Flash failure

1.688159] usb 1-8: new high-speed USB device number 4 using xhci_hcd
[    1.841864] usb 1-8: New USB device found, idVendor=05dc, idProduct=a83a
[    1.841865] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.841866] usb 1-8: Product: USB Flash Drive
[    1.841867] usb 1-8: Manufacturer: Lexar
[    1.841867] usb 1-8: SerialNumber: AA38A4ENI8E0XGSJMS
...
 3.041119] sd 4:0:0:0: [sde] 62517248 512-byte logical blocks: (32.0 GB/29.8 GiB)
[    3.041796] sd 4:0:0:0: [sde] Write Protect is off
[    3.041797] sd 4:0:0:0: [sde] Mode Sense: 43 00 00 00
[    3.042470] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.047455]  sde: sde1
[    3.049971] sd 4:0:0:0: [sde] Attached SCSI removable disk
...
 56.585976] usb 1-8: reset high-speed USB device number 4 using xhci_hcd
...
[  301.657732] sd 4:0:0:0: Device offlined - not ready after error recovery
[  301.657744] usb 1-8: USB disconnect, device number 4
[  301.657751] sd 4:0:0:0: [sde] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  301.657757] sd 4:0:0:0: [sde] tag#0 CDB: Write(10) 2a 00 00 40 0a 38 00 00 80 00
[  301.657760] print_req_error: I/O error, dev sde, sector 4196920
[  301.657770] Buffer I/O error on dev sde1, logical block 524359, lost async page write
[  301.657782] Buffer I/O error on dev sde1, logical block 524360, lost async page write
[  301.657787] Buffer I/O error on dev sde1, logical block 524361, lost async page write
[  301.657791] Buffer I/O error on dev sde1, logical block 524362, lost async page write
[  301.657796] Buffer I/O error on dev sde1, logical block 524363, lost async page write
[  301.657800] Buffer I/O error on dev sde1, logical block 524364, lost async page write
[  301.657805] Buffer I/O error on dev sde1, logical block 524365, lost async page write
[  301.657809] Buffer I/O error on dev sde1, logical block 524366, lost async page write
[  301.657813] Buffer I/O error on dev sde1, logical block 524367, lost async page write
[  301.657817] Buffer I/O error on dev sde1, logical block 524368, lost async page write
[  301.657844] sd 4:0:0:0: rejecting I/O to offline device
[  301.657850] sd 4:0:0:0: killing request
[  301.657856] sd 4:0:0:0: rejecting I/O to offline device
[  301.657861] sd 4:0:0:0: [sde] killing request
[  301.657923] sd 4:0:0:0: [sde] FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[  301.657927] sd 4:0:0:0: [sde] CDB: Write(10) 2a 00 00 40 0a c0 00 00 88 00
[  301.657930] print_req_error: I/O error, dev sde, sector 4197056
[  301.682215] print_req_error: I/O error, dev sde, sector 0
[  301.682220] JBD2: recovery failed
[  301.682221] EXT4-fs (sde1): error loading journal
[  330.606000] usb 1-8: new high-speed USB device number 5 using xhci_hcd
[  330.759443] usb 1-8: New USB device found, idVendor=05dc, idProduct=a83a
[  330.759448] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  330.759451] usb 1-8: Product: USB Flash Drive
[  330.759454] usb 1-8: Manufacturer: Lexar
[  330.759457] usb 1-8: SerialNumber: AA38A4ENI8E0XGSJMS
[  330.760849] usb-storage 1-8:1.0: USB Mass Storage device detected
[  330.761550] scsi host4: usb-storage 1-8:1.0
[  331.954042] scsi 4:0:0:0: Direct-Access     Lexar    USB Flash Drive  1100 PQ: 0 ANSI: 6
[  331.954652] sd 4:0:0:0: Attached scsi generic sg4 type 0
[  331.955359] sd 4:0:0:0: [sde] 62517248 512-byte logical blocks: (32.0 GB/29.8 GiB)
[  331.956036] sd 4:0:0:0: [sde] Write Protect is off
[  331.956040] sd 4:0:0:0: [sde] Mode Sense: 43 00 00 00
[  331.956683] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  331.961844]  sde: sde1
[  331.964967] sd 4:0:0:0: [sde] Attached SCSI removable disk
[  361.837066]  sde: sde1
[ 3675.774582] usb 1-8: reset high-speed USB device number 5 using xhci_hcd
[ 3676.534600] usb 1-8: USB disconnect, device number 5
[ 3676.534631] sd 4:0:0:0: Device offlined - not ready after error recovery
[ 3676.534649] sd 4:0:0:0: [sde] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 3676.534654] sd 4:0:0:0: [sde] tag#0 CDB: Write(10) 2a 00 00 00 00 00 00 00 f0 00
[ 3676.534658] print_req_error: I/O error, dev sde, sector 0
[ 3676.534666] buffer_io_error: 23 callbacks suppressed
[ 3676.534669] Buffer I/O error on dev sde, logical block 0, lost async page write
[ 3676.534687] Buffer I/O error on dev sde, logical block 1, lost async page write
[ 3676.534691] Buffer I/O error on dev sde, logical block 2, lost async page write
[ 3676.534696] Buffer I/O error on dev sde, logical block 3, lost async page write
[ 3676.534700] Buffer I/O error on dev sde, logical block 4, lost async page write
[ 3676.534705] Buffer I/O error on dev sde, logical block 5, lost async page write
[ 3676.534715] Buffer I/O error on dev sde, logical block 6, lost async page write
[ 3676.534720] Buffer I/O error on dev sde, logical block 7, lost async page write
[ 3676.534727] Buffer I/O error on dev sde, logical block 8, lost async page write
[ 3676.534732] Buffer I/O error on dev sde, logical block 9, lost async page write
[ 3676.542438] sd 4:0:0:0: [sde] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 3676.542440] sd 4:0:0:0: [sde] tag#0 CDB: Write(10) 2a 00 00 00 00 f0 00 00 f0 00
[ 3676.542442] print_req_error: I/O error, dev sde, sector 240
[14539.280515] perf: interrupt took too long (2515 > 2500), lowering kernel.perf_event_max_sample_rate to 79500
[18850.555651] perf: interrupt took too long (3168 > 3143), lowering kernel.perf_event_max_sample_rate to 63000
[20020.166862] usb 1-8: new high-speed USB device number 6 using xhci_hcd
[20020.320174] usb 1-8: New USB device found, idVendor=05dc, idProduct=a83a
[20020.320175] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[20020.320176] usb 1-8: Product: USB Flash Drive
[20020.320177] usb 1-8: Manufacturer: Lexar
[20020.320178] usb 1-8: SerialNumber: AA38A4ENI8E0XGSJMS
[20020.321402] usb-storage 1-8:1.0: USB Mass Storage device detected
[20020.321554] scsi host4: usb-storage 1-8:1.0
[20021.534910] scsi 4:0:0:0: Direct-Access     Lexar    USB Flash Drive  1100 PQ: 0 ANSI: 6
[20021.536312] sd 4:0:0:0: [sde] 62517248 512-byte logical blocks: (32.0 GB/29.8 GiB)
[20021.536921] sd 4:0:0:0: [sde] Write Protect is off
[20021.536925] sd 4:0:0:0: [sde] Mode Sense: 43 00 00 00
[20021.537529] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[20021.539187] sd 4:0:0:0: Attached scsi generic sg4 type 0
[20021.546165]  sde: sde1
[20021.548470] sd 4:0:0:0: [sde] Attached SCSI removable disk
[22731.018495]  sde: sde1
[22931.100377] usb 1-8: reset high-speed USB device number 6 using xhci_hcd
[88538.285684] sd 4:0:0:0: Device offlined - not ready after error recovery
[88538.285696] usb 1-8: USB disconnect, device number 6
[88538.285702] sd 4:0:0:0: [sde] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[88538.285708] sd 4:0:0:0: [sde] tag#0 CDB: Write(10) 2a 00 00 40 0a 38 00 00 80 00
[88538.285712] print_req_error: I/O error, dev sde, sector 4196920
[88538.285721] buffer_io_error: 50 callbacks suppressed
[88538.285723] Buffer I/O error on dev sde1, logical block 524359, lost async page write
[88538.285737] Buffer I/O error on dev sde1, logical block 524360, lost async page write
[88538.285742] Buffer I/O error on dev sde1, logical block 524361, lost async page write
[88538.285747] Buffer I/O error on dev sde1, logical block 524362, lost async page write
[88538.285752] Buffer I/O error on dev sde1, logical block 524363, lost async page write
[88538.285756] Buffer I/O error on dev sde1, logical block 524364, lost async page write
[88538.285761] Buffer I/O error on dev sde1, logical block 524365, lost async page write
[88538.285765] Buffer I/O error on dev sde1, logical block 524366, lost async page write
[88538.285770] Buffer I/O error on dev sde1, logical block 524367, lost async page write
[88538.285775] Buffer I/O error on dev sde1, logical block 524368, lost async page write
[88538.285810] sd 4:0:0:0: rejecting I/O to offline device
[88538.285815] sd 4:0:0:0: killing request
[88538.285916] sd 4:0:0:0: [sde] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[88538.285920] sd 4:0:0:0: [sde] tag#0 CDB: Write(10) 2a 00 00 40 0a c0 00 00 88 00
[88538.285923] print_req_error: I/O error, dev sde, sector 4197056
[88584.518158] usb 1-8: new high-speed USB device number 7 using xhci_hcd
[88584.671605] usb 1-8: New USB device found, idVendor=05dc, idProduct=a83a
[88584.671607] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[88584.671609] usb 1-8: Product: USB Flash Drive
[88584.671610] usb 1-8: Manufacturer: Lexar
[88584.671611] usb 1-8: SerialNumber: AA38A4ENI8E0XGSJMS
[88584.672896] usb-storage 1-8:1.0: USB Mass Storage device detected
[88584.673213] scsi host4: usb-storage 1-8:1.0
[88585.894322] scsi 4:0:0:0: Direct-Access     Lexar    USB Flash Drive  1100 PQ: 0 ANSI: 6
[88585.895096] sd 4:0:0:0: Attached scsi generic sg4 type 0
[88585.895883] sd 4:0:0:0: [sde] 62517248 512-byte logical blocks: (32.0 GB/29.8 GiB)
[88585.896550] sd 4:0:0:0: [sde] Write Protect is off
[88585.896555] sd 4:0:0:0: [sde] Mode Sense: 43 00 00 00
[88585.897174] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[88585.902972]  sde: sde1
[88585.906418] sd 4:0:0:0: [sde] Attached SCSI removable disk
[88621.759001] usb 1-8: reset high-speed USB device number 7 using xhci_hcd