Starting Klippy...
Args: ['/home/capocchione/klipper/klippy/klippy.py', '/home/capocchione/printer_data/config/printer.cfg', '-I', '/home/capocchione/printer_data/comms/klippy.serial', '-l', '/home/capocchione/printer_data/logs/klippy.log', '-a', '/home/capocchione/printer_data/comms/klippy.sock']
Git version: 'v0.11.0-271-g5f990f93-dirty'
Modified files: scripts/install-octopi.sh
Branch: master
Remote: origin
Tracked URL: https://github.com/Klipper3d/klipper
CPU: 4 core ARMv7 Processor rev 4 (v7l)
Python: '3.9.2 (default, Mar 12 2021, 04:06:34) \n[GCC 10.2.1 20210110]'
Start printer at Mon Aug 28 23:20:37 2023 (1693257637.9 32.0)
===== Config file =====
[stepper_x]
step_pin = ar54
dir_pin = !ar55
enable_pin = !ar38
microsteps = 16
rotation_distance = 40
endstop_pin = ^!ar3
position_min = -5
position_endstop = -5
position_max = 210
homing_speed = 30
homing_retract_dist = 5
second_homing_speed = 10

[stepper_y]
step_pin = ar60
dir_pin = ar61
enable_pin = !ar56
microsteps = 16
rotation_distance = 40
endstop_pin = ^!ar42
position_endstop = 0
position_max = 210
homing_speed = 50
homing_retract_dist = 5
second_homing_speed = 10

[stepper_z]
step_pin = ar46
dir_pin = ar48
enable_pin = !ar62
microsteps = 16
rotation_distance = 8
endstop_pin = ^!ar18
position_endstop = 0.0
position_max = 205
homing_speed = 10
homing_retract_dist = 5
second_homing_speed = 3

[stepper_z1]
step_pin = ar36
dir_pin = ar34
endstop_pin = ^!ar43
enable_pin = !ar30
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = ar26
dir_pin = ar28
enable_pin = !ar24
control = pid
microsteps = 16
rotation_distance = 7.495
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = ar10
sensor_type = ATC Semitec 104GT-2
sensor_pin = analog13
min_temp = 0
max_temp = 285
max_extrude_only_distance = 150.0
smooth_time = 1
min_extrude_temp = 180
pressure_advance = 0.1
max_extrude_cross_section = 150
pid_kp = 26.839
pid_ki = 1.612
pid_kd = 111.716

[heater_fan extruder_fan]
pin = ar44

[heater_bed]
heater_pin = ar8
sensor_type = EPCOS 100K B57560G104F
sensor_pin = analog14
min_temp = 0
max_temp = 110
smooth_time = 1
control = pid
pid_kp = 73.627
pid_ki = 3.272
pid_kd = 414.154

[fan]
pin = ar9

[mcu]
serial = /dev/serial/by-id/usb-Silicon_Labs_CP2102_USB_to_UART_Bridge_Controller_0001-if00-port0

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 4000
max_accel_to_decel = 1500
max_z_velocity = 7
max_z_accel = 190
square_corner_velocity = 5

[heater_fan stepstick_fan]
pin = ar7

[safe_z_home]
home_xy_position = 100,100
speed = 150
z_hop = 5
z_hop_speed = 10

[bed_mesh]
speed = 50
horizontal_move_z = 5
mesh_min = 30,30
mesh_max = 180,180
probe_count = 5,5
fade_start = 1.0
fade_end = 10.0

[force_move]
enable_force_move = True

[virtual_sdcard]
path = ~/.octoprint/uploads/

[output_pin BEEPER_pin]
pin = ar31
pwm = True
value = 0
shutdown_value = 0
cycle_time = 0.001
scale = 1000

[gcode_macro M300]
gcode =
	{% set S = params.S|default(1000) %}
	{% set P = params.P|default(100) %}
	SET_PIN PIN=BEEPER_pin VALUE={S}
	G4 P{P}
	SET_PIN PIN=BEEPER_pin VALUE=0

[display_status]

[pause_resume]

[gcode_macro M600]
gcode =
	{% set X = params.X|default(50) %}
	{% set Y = params.Y|default(0) %}
	{% set Z = params.Z|default(10) %}
	SAVE_GCODE_STATE NAME=M600_state
	PAUSE
	G91
	G1 E-.8 F2700
	G1 Z{Z}
	G90
	G1 X{X} Y{Y} F3000
	G91
	G1 E-150 F1000
	M300 S299 P200
	M300 S299 P200
	M300 S299 P200
	M300 S299 P200
	M300 S299 P200
	RESTORE_GCODE_STATE NAME=M600_state

[gcode_macro PAUSE]
rename_existing = BASE_PAUSE
variable_extrude = 1.0
gcode =

	{% set E = printer["gcode_macro PAUSE"].extrude|float %}


	{% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}
	{% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}

	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% if act_z < (max_z - 2.0) %}
	{% set z_safe = 2.0 %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}

	SAVE_GCODE_STATE NAME=PAUSE_state
	BASE_PAUSE
	G91
	G1 E-{E} F2100
	G1 Z{z_safe} F900
	G90
	G1 X{x_park} Y{y_park} F6000

[gcode_macro RESUME]
rename_existing = BASE_RESUME
gcode =

	{% set E = printer["gcode_macro PAUSE"].extrude|float %}

	G91
	G1 E{E} F2100
	RESTORE_GCODE_STATE NAME=PAUSE_state
	BASE_RESUME

[gcode_macro CANCEL_PRINT]
rename_existing = BASE_CANCEL_PRINT
gcode =
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	SDCARD_RESET_FILE
	BASE_CANCEL_PRINT

[gcode_macro START_PRINT]
gcode =
	{% set BED_TEMP = params.BED_TEMP|default(60)|float %}
	{% set EXTRUDER_TEMP = params.EXTRUDER_TEMP|default(190)|float %}
	G21
	G90
	M82
	M107
	M190 S{BED_TEMP}
	M109 S{EXTRUDER_TEMP}
	M300 S1000 P500
	G28 X0 Y10 Z0
	M420 S1
	M420 Z5.0
	G0 Z0.15
	G0 Y10
	G92 E0
	G1 X50 E50 F500
	G92 E0
	G1 E-3 F500
	G1 X120 F4000

[gcode_macro END_PRINT]
gcode =
	M104 S0
	M140 S0
	M107
	G91
	G1 E-5 F300
	G1 Z+10
	G28 X0 Y0
	G1 Y180 F2000
	M84
	G90
	M300 S440 P200
	M300 S660 P250
	M300 S880 P300

[bed_mesh default]
version = 1
points =
	0.082500, 0.032500, 0.005000, 0.030000
	0.072500, -0.007500, -0.002500, -0.012500
	0.077500, 0.027500, -0.007500, 0.017500
	0.077500, 0.030000, 0.002500, 0.007500
tension = 0.2
min_x = 23.0
algo = bicubic
y_count = 4
mesh_y_pps = 2
min_y = 28.0
x_count = 4
max_y = 190.0
mesh_x_pps = 2
max_x = 189.97

[input_shaper]
shaper_type_x = 3hump_ei
shaper_freq_x = 73.0
shaper_type_y = 3hump_ei
shaper_freq_y = 60.0
=======================
Extruder max_extrude_ratio=62.362753
mcu 'mcu': Starting serial connect
Loaded MCU 'mcu' 112 commands (v0.11.0-271-g5f990f93-dirty-20230828_221435-raspberrypi / gcc: (GCC) 5.4.0 binutils: (GNU Binutils) 2.26.20160125)
MCU 'mcu' config: ADC_MAX=1023 BUS_PINS_spi=PB3,PB2,PB1 BUS_PINS_twi=PD0,PD1 CLOCK_FREQ=16000000 MCU=atmega2560 PWM_MAX=255 RECEIVE_WINDOW=192 RESERVE_PINS_serial=PE0,PE1 SERIAL_BAUD=250000 STATS_SUMSQ_BASE=256
Sending MCU 'mcu' printer configuration...
Config error
Traceback (most recent call last):
  File "/home/capocchione/klipper/klippy/mcu.py", line 707, in _send_config
    self._serial.send(c)
  File "/home/capocchione/klipper/klippy/serialhdl.py", line 256, in send
    cmd = self.msgparser.create_command(msg)
  File "/home/capocchione/klipper/klippy/msgproto.py", line 350, in create_command
    cmd = mp.encode_by_name(**argparts)
  File "/home/capocchione/klipper/klippy/msgproto.py", line 181, in encode_by_name
    t.encode(out, params[name])
  File "/home/capocchione/klipper/klippy/msgproto.py", line 108, in encode
    raise enumeration_error(self.enum_name, v)
msgproto.enumeration_error: Unknown value 'ar44' in enumeration 'pin'

During handling of the above exception, another exception occurred:

Traceback (most recent call last):
  File "/home/capocchione/klipper/klippy/klippy.py", line 180, in _connect
    cb()
  File "/home/capocchione/klipper/klippy/mcu.py", line 753, in _connect
    self._send_config(None)
  File "/home/capocchione/klipper/klippy/mcu.py", line 718, in _send_config
    raise self._printer.config_error(
configparser.Error: Pin 'ar44' is not a valid pin name on mcu 'mcu'
webhooks client 1965567424: New connection
webhooks client 1965567424: Client info {'program': 'Moonraker', 'version': 'v0.8.0-138-gfe12095'}