Honda Civic Work

2023-05-26 21:39:10 ★ Cletus Taylor pulls the Skyline into the garage, parking it in position between the legs of the ---
2023-05-26 21:39:23 ★ two post lift before hopping out.      ((Cletus Taylor))
2023-05-26 21:39:44 ★ Cletus Taylor goes to each side of the car, deploying out the lift legs of the hoist; guiding them into --
2023-05-26 21:39:51 ★ position underneath the Skyline's lift points.      ((Cletus Taylor))
2023-05-26 21:40:04 ★ Cletus Taylor walks over and grabs the impact wrench from the floor, then plugs it in.
2023-05-26 21:40:19 ★ Cletus Taylor heads over to the Nissan, proceeding to quickly go about loosening the lug nuts on each ---
2023-05-26 21:40:27 ★ of the four wheels prior to lifting the vehicle.      ((Cletus Taylor))
2023-05-26 21:40:42 ★ Cletus Taylor places the impact wrench down, then grabs the lever on the jack pressing it ---
2023-05-26 21:40:55 ★ up in order to lift the vehicle up a few feet.      ((Cletus Taylor))
2023-05-26 21:41:14 ★ Cletus Taylor grabs the impact wrench, proceeding to loosen each of the lug nuts the remainder of ---
2023-05-26 21:41:22 ★ the way, then places the impact on the floor.      ((Cletus Taylor))
2023-05-26 21:41:31 ★ Cletus Taylor grabs each wheel, one by one removing them and rolling them aside.
2023-05-26 21:42:04 ★ Cletus Taylor grabs a pair of adjustable wrenches, then heads back to the front-left corner of the ---
2023-05-26 21:42:20 ★ Skyline. He'd adjust one wrench to the nut and the other to the bolt itself, he'd hold ---      ((Cletus Taylor))
2023-05-26 21:42:47 ★ the nut still, then proceeds to loosen the bolt.      ((Cletus Taylor))
2023-05-26 21:43:07 ★ Cletus Taylor quickly cranks the bolt to the left, loosening it from the nut allowing the nut to fall off.
2023-05-26 21:43:34 ★ Cletus Taylor places the wrench into his pocket, then grabs the factory strut with both hands ---
2023-05-26 21:43:52 ★ pulling on the strut in order to pop it from its bracket on the lower control arm.      ((Cletus Taylor))
2023-05-26 21:44:07 ★ Cletus Taylor stands up and opens the driver's door, he'd pull the hood release lever and then presses ---
2023-05-26 21:44:15 ★ the trunk release button in before heading to the hood.      ((Cletus Taylor))
2023-05-26 21:44:39 ★ Cletus Taylor slides his hand under the hood and slips the latch aside, then lifts the hood open and ---
2023-05-26 21:44:45 ★ places the prop into position holding it up.      ((Cletus Taylor))
2023-05-26 21:45:04 ★ Cletus Taylor grabs the wrench, proceeding to go about loosening the four nuts on the top of ---
2023-05-26 21:45:27 ★ the factory strut assembly, thus freeing it from the strut tower.      ((Cletus Taylor))
2023-05-26 21:45:43 ★ Cletus Taylor crouches down and grabs the factory strut, pulling it out and yeets it across the shop.
2023-05-26 21:45:50 Cletus Taylor says: Piece of shit.
2023-05-26 21:46:10 ★ Cletus Taylor walks over to the passenger side of the car, proceeding to grab the other wrench.
2023-05-26 21:46:29 ★ Cletus Taylor crouches down in position, proceeding to hold the nut still with one wrench; then quickly --
2023-05-26 21:46:36 ★ goes about loosening the bolt itself with the other.      ((Cletus Taylor))
2023-05-26 21:46:56 ★ Cletus Taylor pockets the wrenches, then grabs the strut assembly and pulls it from its mounting ---
2023-05-26 21:47:02 ★ socket on the lower control arm.      ((Cletus Taylor))
2023-05-26 21:47:15 ★ Cletus Taylor stands up and grabs one of the wrenches from his pocket, he'd quickly loosen the ---
2023-05-26 21:47:39 ★ nuts on the upper section of the strut, thus freeing it from the tower.      ((Cletus Taylor))
2023-05-26 21:47:51 ★ Cletus Taylor crouches down and grabs the factory strut, pulling it out then tosses it aside.
2023-05-26 21:48:06 ★ Cletus Taylor walks to the back of the Nissan, proceeding to do the same; he'd grab the other ---
2023-05-26 21:48:19 ★ wrench and holds the nut still with it, quickly loosening the bolt from the lower section --      ((Cletus Taylor))
2023-05-26 21:48:22 ★ of the strut.      ((Cletus Taylor))
2023-05-26 21:48:49 ★ Cletus Taylor stands up and opens the trunk, he'd grab the carpet on each side pulling it to the center.
2023-05-26 21:49:13 ★ Cletus Taylor reaches to the corner of the trunk, proceeding to loosen each of the four nuts on ---
2023-05-26 21:49:26 ★ the upper section of the strut, thus freeing it from the chassis.      ((Cletus Taylor))
2023-05-26 21:49:41 ★ Cletus Taylor moves onto the opposite side, then crouches down and grabs the other wrench
2023-05-26 21:49:57 ★ Cletus Taylor holds the nut still, proceeding to quickly crank the wrench to the left, loosening the bolt.
2023-05-26 21:50:12 ★ Cletus Taylor grabs the lower strut section, pulling it from its place on the LCA; then pockets the wrench
2023-05-26 21:50:24 ★ Cletus Taylor grabs the rear-left strut, proceeding to pull it out then tosses it over his shoulder.
2023-05-26 21:50:39 ★ Cletus Taylor moves onto the other side of the Nissan, proceeding to grab the strut, popping it out.
2023-05-26 21:50:48 ★ Cletus Taylor drops the strut with the other three, then chuckles.
2023-05-26 21:50:52 Cletus Taylor says: No suspension at all...
2023-05-26 21:51:04 ★ Cletus Taylor walks over to the trunk, proceeding to open the BC Racing box.
2023-05-26 21:51:16 ★ Cletus Taylor grabs both rear coilovers, then heads over to the passenger side.
2023-05-26 21:51:34 ★ Cletus Taylor carefully sockets the coilover into place, grabbing the nut and bolt from the floor.
2023-05-26 21:51:53 ★ Cletus Taylor hand threads the bolt through the coilover, holding the nut still to loosely secure the ---
2023-05-26 21:52:12 ★ coilover in place. He'd guide the top of the coilover through the holes on the chassis, -      ((Cletus Taylor))
2023-05-26 21:52:28 ★ then stands up and goes to the trunk, carefully threading the nutes onto the top of the coil      ((Cletus Taylor))
2023-05-26 21:52:43 ★ Cletus Taylor walks over to the driver's side, proceeding to do the same; he'd socket the coilover ---
2023-05-26 21:53:01 ★ into place on the LCA, hand tightening the nut and bolt; then guides the top of the ---      ((Cletus Taylor))
2023-05-26 21:53:06 ★ coilover into the holes.      ((Cletus Taylor))
2023-05-26 21:53:16 ★ Cletus Taylor grabs the nuts from the trunk, hand threading them into place.
2023-05-26 21:53:36 ★ Cletus Taylor grabs the wrench, proceeding to tighten the bolts up top, then goes and crouches down ---
2023-05-26 21:53:53 ★ on the left-hand side of the car. He'd hold the nut in position, then quickly cranks the ---      ((Cletus Taylor))
2023-05-26 21:54:02 ★ bolt itself to the right tightening it down      ((Cletus Taylor))
2023-05-26 21:54:13 ★ Cletus Taylor grabs the front coilovers, then heads to the front of the Nissan.
2023-05-26 21:55:02 ★ Cletus Taylor slides the front-right coilover into position on the strut tower, then guides the bottom ---
2023-05-26 21:55:18 ★ of it into place on the LCA. He'd grab the nut and bolt, proceeding to thread them together      ((Cletus Taylor))
2023-05-26 21:55:35 ★ through their holes. Once done, he'd grab both wrenches, proceeding to hold the nut ----      ((Cletus Taylor))
2023-05-26 21:55:45 ★ still, then quickly cranks the bolt to the right tightening them togheter.      ((Cletus Taylor))
2023-05-26 21:57:00 ★ Cletus Taylor takes the final coilover, then heads to the driver's side of the car.
2023-05-26 21:57:10 ★ Cletus Taylor slides the front-left coilover into position on the strut tower, then guides the bottom ---
2023-05-26 21:57:17 ★ of it into place on the LCA. He'd grab the nut and bolt, proceeding to thread them together      ((Cletus Taylor))
2023-05-26 21:57:26 ★ through their holes. Once done, he'd grab both wrenches, proceeding to hold the nut ----      ((Cletus Taylor))
2023-05-26 21:57:33 ★ still, then quickly cranks the bolt to the right tightening them togheter.      ((Cletus Taylor))
2023-05-26 21:57:51 ★ Cletus Taylor walks over and grabs each of the four wheels, rolling them to their respective corners.
2023-05-26 21:58:12 ★ Cletus Taylor goes around one-by-one lifting the wheels up, sliding them onto the studs on the hub ---
2023-05-26 21:58:25 ★ assemblies, he'd grab the lug nuts from the floor and threads them on by hand.      ((Cletus Taylor))
2023-05-26 21:58:40 ★ Cletus Taylor walks over and grabs the lift control lever, lowering the lift down to the floor.
2023-05-26 21:58:59 ★ Cletus Taylor grabs the impact wrench, pressing the switch to the right to allow it to tighten instead ---
2023-05-26 21:59:05 ★ of loosening the nuts.      ((Cletus Taylor))
2023-05-26 21:59:22 ★ Cletus Taylor goes around the Nissan, tightening the lug nuts in a star-like pattern; then places it down.
2023-05-29 23:40:57 ★ Cletus Taylor yawns as he stretches, looking at the Honda.
2023-05-29 23:42:20 ★ Cletus Taylor heads over to the toolbox and grabs a ratchet set, along with a pair of gloves.
2023-05-29 23:42:32 ★ Cletus Taylor slips the gloves on, then continues to open the ratchet set.
2023-05-29 23:42:55 ★ Cletus Taylor grabs the ratchet from within the toolkit, then leans into the already opened ---
2023-05-29 23:43:06 ★ hood of the Honda, eyeing the exhaust header.      ((Cletus Taylor))
2023-05-29 23:43:55 ★ Cletus Taylor eyeballs the bolts on the header, sizing them up in his head. He'd place the socket ---
2023-05-29 23:45:08 ★ wrench down and then grabs an adjustable wrench from the ground from his ---      ((Cletus Taylor))
2023-05-29 23:45:13 ★ previous suspension work.      ((Cletus Taylor))
2023-05-29 23:45:30 ★ Cletus Taylor reaches for the O2 Sensor, adjusting the wrench to size; then twists the nut on the ---
2023-05-29 23:45:37 ★ sensor to the left, loosening it to remove it.      ((Cletus Taylor))
2023-05-29 23:45:48 ★ Cletus Taylor places the wrench in his pocket and hangs the O2 sensor aside.
2023-05-29 23:46:24 ★ Cletus Taylor grabs his ratchet, proceeding to one-by-one loosen each of the upper header bolts ---
2023-05-29 23:46:37 ★ from right to left, then heads to the control panel.      ((Cletus Taylor))
2023-05-29 23:46:50 ★ Cletus Taylor presses up on the lever, lifting the Honda up into the air.
2023-05-29 23:49:18 ★ Cletus Taylor steps underneath the lift and gazes up at the Header from underneath.
2023-05-29 23:50:12 ★ Cletus Taylor eyes the end of the header, then the catalytic converter.
2023-05-29 23:50:33 ★ Cletus Taylor steps over to the corner, grabbing a long plank of wood left over from the basement ---
2023-05-29 23:50:48 ★ renovations, then sticks it between the catalytic converter and the floor as a support.      ((Cletus Taylor))
2023-05-29 23:51:10 ★ Cletus Taylor grabs the wrench from his pocket, along with the ratchet from the floor; then reaches ---
2023-05-29 23:51:24 ★ up to one of the two bolts on the header.      ((Cletus Taylor))
2023-05-29 23:51:41 ★ Cletus Taylor holds the nut still with the wrench, proceeding to crank the bolt to the left with the ---
2023-05-29 23:51:53 ★ ratchet, he'd allow the bolt to fall to the floor then moves onto the other.      ((Cletus Taylor))
2023-05-29 23:52:06 ★ Cletus Taylor places both tools on the floor, proceeding to grip the header with both hands carefully ---
2023-05-29 23:52:20 ★ wiggling it through the engine bay, dropping it out then carries it aside.      ((Cletus Taylor))
2023-05-29 23:52:39 ★ Cletus Taylor places the stock header on the floor, proceeding to grab the fresh Stainless Yonaka ---
2023-05-29 23:52:48 ★ header, then heads back to the Honda.      ((Cletus Taylor))
2023-05-29 23:53:41 ★ Cletus Taylor grabs the nuts and bolts from the floor, proceeding to then lift the header up and ---
2023-05-29 23:53:57 ★ carefully slides it into the engine bay. He'd line the end of the header up with the ---      ((Cletus Taylor))
2023-05-29 23:54:16 ★ catalytic converter, then hand threads the bolt through to loosely hold it in place.      ((Cletus Taylor))
2023-05-29 23:54:36 ★ Cletus Taylor grips the nut, twisting both back into place one-by-one, then grips his wrench and ---
2023-05-29 23:54:44 ★ holds them still as he cranks both down with the ratchet.      ((Cletus Taylor))
2023-05-29 23:54:59 ★ Cletus Taylor steps out from underneath the lift, then lowers the car back down to floor lever.
2023-05-29 23:55:17 ★ Cletus Taylor steps infront of the car, proceeding to grab the Yonaka box as he removes the ---
2023-05-29 23:55:25 ★ shiny new polished hardware from within it.      ((Cletus Taylor))
2023-05-29 23:56:05 ★ Cletus Taylor slides the new polished bolts into their holes by hand, then slides the new gasket into place.
2023-05-29 23:56:39 ★ Cletus Taylor then grabs his ratchet and begins to crank the bolts down in an alternating pattern -
2023-05-29 23:56:57 ★ securing the header and the gasket into place on the cylinder head.      ((Cletus Taylor))
2023-05-29 23:57:16 ★ Cletus Taylor steps back to the control panel, proceeding to grab the lever pressing it up.
2023-05-29 23:57:39 ★ Cletus Taylor walks underneath the lift, then eyes the rear of the catalytic converter all the way back.
2023-05-29 23:59:28 ★ Cletus Taylor grabs the wrench and ratchet, sighing as he gets to work.
2023-05-29 23:59:47 ★ Cletus Taylor connects the ratchet to one of the two bolts at the rear of the cat, then ---
2023-05-30 00:00:11 ★ proceeds to hold the nut still with the wrench as he cranks the ratchet to the right.      ((Cletus Taylor))
2023-05-30 00:00:28 ★ Cletus Taylor drops the bolt and nut, then moves onto the other, loosening it too.
2023-05-30 00:01:10 ★ Cletus Taylor grabs the wooden plank, un-wedging it from the cat, then moves it out of the way.
2023-05-30 00:01:47 ★ Cletus Taylor goes back underneath the lift, proceeding to carefully wiggle the steel exhaust ---
2023-05-30 00:02:06 ★ hangars from the rubberized sockets on the chassis of the Honda.      ((Cletus Taylor))
2023-05-30 00:02:39 ★ Cletus Taylor continues to move towards the back of the Honda, working each exhaust hangar free.
2023-05-30 00:03:24 ★ The exhaust would be hanging from the muffler, as it goes over the rear-right LCA.      ((Cletus Taylor))
2023-05-30 00:03:39 ★ Cletus Taylor goes to the middle of the car and grabs his wrench and ratchet, then heads back.
2023-05-30 00:04:02 ★ Cletus Taylor connects the wrench to the nut, then takes the ratchet and begins to crank the bolt ---
2023-05-30 00:04:10 ★ to the left, loosening it until it falls.      ((Cletus Taylor))
2023-05-30 00:04:32 ★ As he removes the bolts, the entire middle section of the exhaust system would drop ---      ((Cletus Taylor))
2023-05-30 00:04:46 ★ and hit the floor, leaving just the muffler hanging from its hangar.      ((Cletus Taylor))
2023-05-30 00:04:56 ★ Cletus Taylor grabs the muffler, wiggling it free then places it aside.
2023-05-30 00:05:22 Cletus Taylor says: Alright, I should fire it up... straight pipe from the cat back.
2023-05-30 00:05:28 ★ Cletus Taylor chuckles, then shakes his head.
2023-05-30 00:05:31 Cletus Taylor says: Nahhh.
2023-05-30 00:05:54 ★ Cletus Taylor grabs the Yonaka box, opening it up as he'd then remove each piece of the Honda's ---
2023-05-30 00:06:13 ★ new exhaust system. He'd lay out the pipes piece by piece where they'd belong, then ---      ((Cletus Taylor))
2023-05-30 00:06:28 ★ takes out the fresh hardware and hand-threads them together in order to loosely ---      ((Cletus Taylor))
2023-05-30 00:06:32 ★ hold the pipes together.      ((Cletus Taylor))
2023-05-30 00:06:50 ★ Cletus Taylor grabs the wrench and his socket, then begins to tighten the fixtures together.
2023-05-30 00:07:11 ★ Cletus Taylor pockets both tools, then carefully picks up the polished 3-Inch exuast kit and carries ---
2023-05-30 00:07:28 ★ it over to the Honda. He'd grip the leftover wooden plank, carefully wedging it between ---      ((Cletus Taylor))
2023-05-30 00:07:42 ★ the exhaust and the floor in order to form a makeshift support.      ((Cletus Taylor))
2023-05-30 00:08:02 ★ Cletus Taylor grabs two bolts and a couple shiny nuts from his bag, then proceeds to thread the ---
2023-05-30 00:08:30 ★ bolt through the hole, thus loosely securing the midpipe to the catalytic converter.      ((Cletus Taylor))
2023-05-30 00:09:02 ★ Cletus Taylor walks back, carefully slides the hangards into their rubberized holes on the chassis, ---
2023-05-30 00:09:12 ★ carefully securing the pipes into place.      ((Cletus Taylor))
2023-05-30 00:09:28 ★ Cletus Taylor grabs the wrench and socket from his pocket, then heads back up front.
2023-05-30 00:09:45 ★ Cletus Taylor holds the nut in place, proceeding to quickly crank the bolt through securing the ---
2023-05-30 00:09:52 ★ midpipe to the catalytic converter.      ((Cletus Taylor))
2023-05-30 00:10:13 ★ Cletus Taylor grabs the new Yonaka muffle, then lifts it up and holds it in place as he hand-threads the -
2023-05-30 00:10:29 ★ bolt through the hole. He'd release the muffle, proceeding to then griip his wrench.      ((Cletus Taylor))
2023-05-30 00:10:54 ★ Cletus Taylor holds the nut still, proceeding to crank the bolt to the right with the wrench tightening --
2023-05-30 00:10:57 ★ them together.      ((Cletus Taylor))
2023-05-30 00:11:05 Cletus Taylor says: Alright... intake and I am done.
2023-05-30 00:14:07 ★ Cletus Taylor lowers the lift, then grabs the Injen box from the trunk.
2023-05-30 00:14:43 ★ Cletus Taylor grabs the O2 Sensor, twisting it back into the hole on the header; then grips the wrench.
2023-05-30 00:15:40 ★ Cletus Taylor tightens the O2 Sensor down, then focuses on the intake manifold.
2023-05-30 00:16:02 ★ Cletus Taylor reaches towards the intake manifold, then uses the wrench to loosen the hose clamp ---
2023-05-30 00:16:08 ★ on the factory intake tube.      ((Cletus Taylor))
2023-05-30 00:16:28 ★ Cletus Taylor grabs the entire factory intake tube and box, carefully pulling it out, then places it aside
2023-05-30 00:16:51 ★ Cletus Taylor unhooks the MAF Sensor, then hangs it aside as he proceeds to loosen the final ---
2023-05-30 00:17:00 ★ hose clamp on the stock intake.      ((Cletus Taylor))
2023-05-30 00:17:14 ★ Cletus Taylor grabs the elbow tube, taking it off then places it aside.
2023-05-30 00:17:37 ★ Cletus Taylor grabs the Injen Cold Air Intake and proceeds to pop the tubing into place. He'd carefully -
2023-05-30 00:17:50 ★ align the hose clamps, then cranks them down securing the intake.      ((Cletus Taylor))
2023-05-30 00:29:31 ★ Cletus Taylor grabs the drill from his toolbag, proceeding to swap over the bit for a hole saw drill bit.
2023-05-30 00:29:45 ★ Cletus Taylor goes behind the Honda to the rear bumper, proceeding to drill eight large holes in the ---
2023-05-30 00:30:15 ★ bumper, thus slightly reducing drag caused by the rear-bumper of the Honda.      ((Cletus Taylor))