Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- smartctl 6.6 2017-11-05 r4594 [i686-w64-mingw32-win7(64)-sp1] (sf-6.6-1)
- Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Model Family: Hitachi/HGST Travelstar Z5K500
- Device Model: HGST HTS545050A7E680
- Serial Number: RBF52AAH1S7PNP
- LU WWN Device Id: 5 000cca 8aad8a8f0
- Firmware Version: GR2OA230
- User Capacity: 500107862016 bytes [500 GB]
- Sector Sizes: 512 bytes logical, 4096 bytes physical
- Rotation Rate: 5400 rpm
- Form Factor: 2.5 inches
- Device is: In smartctl database [for details use: -P show]
- ATA Version is: ATA8-ACS T13/1699-D revision 6
- SATA Version is: SATA 2.6, 6.0 Gb/s (current: 1.5 Gb/s)
- Local Time is: Wed Jun 20 16:57:30 2018
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- AAM feature is: Unavailable
- APM level is: 128 (minimum power consumption without standby)
- Rd look-ahead is: Enabled
- Write cache is: Enabled
- DSN feature is: Unavailable
- ATA Security is: Disabled, NOT FROZEN [SEC1]
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x00) Offline data collection activity
- was never started.
- Auto Offline Data Collection: Disabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: ( 45) seconds.
- Offline data collection
- capabilities: (0x5b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- No Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 2) minutes.
- Extended self-test routine
- recommended polling time: ( 120) minutes.
- SCT capabilities: (0x003d) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
- 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0
- 2 Throughput_Performance P-S--- 100 100 040 - 0
- 3 Spin_Up_Time POS--- 253 253 033 - 1
- 4 Start_Stop_Count -O--C- 099 099 000 - 2493
- 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0
- 7 Seek_Error_Rate PO-R-- 100 100 067 - 0
- 8 Seek_Time_Performance P-S--- 100 100 040 - 0
- 9 Power_On_Hours -O--C- 083 083 000 - 7716
- 10 Spin_Retry_Count PO--C- 100 100 060 - 0
- 12 Power_Cycle_Count -O--CK 099 099 000 - 2493
- 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0
- 192 Power-Off_Retract_Count -O--CK 089 089 000 - 2365
- 193 Load_Cycle_Count -O--C- 045 045 000 - 555436
- 194 Temperature_Celsius -O---- 206 206 000 - 29 (Min/Max 15/41)
- 196 Reallocated_Event_Count -O--CK 100 100 000 - 0
- 197 Current_Pending_Sector -O---K 100 100 000 - 0
- 198 Offline_Uncorrectable ---R-- 100 100 000 - 0
- 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0
- 223 Load_Retry_Count -O-R-- 100 100 000 - 0
- ||||||_ K auto-keep
- |||||__ C event count
- ||||___ R error rate
- |||____ S speed/performance
- ||_____ O updated online
- |______ P prefailure warning
- ATA_READ_LOG_EXT (addr=0x00:0x00, page=0, n=1) failed: 48-bit ATA commands not implemented [JMicron]
- Read GP Log Directory failed
- SMART Log Directory Version 1 [multi-sector log support]
- Address Access R/W Size Description
- 0x00 SL R/O 1 Log Directory
- 0x01 SL R/O 1 Summary SMART error log
- 0x02 SL R/O 1 Comprehensive SMART error log
- 0x06 SL R/O 1 SMART self-test log
- 0x09 SL R/W 1 Selective self-test log
- 0x80-0x9f SL R/W 16 Host vendor specific log
- 0xe0 SL R/W 1 SCT Command/Status
- 0xe1 SL R/W 1 SCT Data Transfer
- SMART Extended Comprehensive Error Log (GP Log 0x03) not supported
- SMART Error Log Version: 1
- ATA Error Count: 12 (device log contains only the most recent five errors)
- CR = Command Register [HEX]
- FR = Features Register [HEX]
- SC = Sector Count Register [HEX]
- SN = Sector Number Register [HEX]
- CL = Cylinder Low Register [HEX]
- CH = Cylinder High Register [HEX]
- DH = Device/Head Register [HEX]
- DC = Device Command Register [HEX]
- ER = Error register [HEX]
- ST = Status register [HEX]
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 12 occurred at disk power-on lifetime: 7716 hours (321 days + 12 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 10 51 08 00 00 00 00 Error: IDNF 8 sectors at LBA = 0x00000000 = 0
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 08 00 00 00 e0 00 00:01:45.928 READ DMA EXT
- e5 00 00 00 00 00 a0 00 00:01:45.926 CHECK POWER MODE
- ef 03 46 00 00 00 a0 00 00:01:45.926 SET FEATURES [Set transfer mode]
- 25 00 08 00 00 00 00 04 00:01:45.896 READ DMA EXT
- 25 00 08 00 00 00 e0 00 00:01:27.274 READ DMA EXT
- Error 11 occurred at disk power-on lifetime: 7716 hours (321 days + 12 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 10 51 08 00 00 00 00 Error: IDNF 8 sectors at LBA = 0x00000000 = 0
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 08 00 00 00 e0 00 00:01:27.274 READ DMA EXT
- 25 00 08 18 30 1c e0 00 00:01:27.096 READ DMA EXT
- 25 00 08 28 60 38 e0 00 00:01:25.960 READ DMA EXT
- e5 00 00 00 00 00 a0 00 00:01:25.960 CHECK POWER MODE
- ef 03 46 00 00 00 a0 00 00:01:25.959 SET FEATURES [Set transfer mode]
- Error 10 occurred at disk power-on lifetime: 7716 hours (321 days + 12 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 10 51 08 00 00 00 00 Error: IDNF 8 sectors at LBA = 0x00000000 = 0
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 08 00 00 00 e0 00 00:01:07.550 READ DMA EXT
- e5 00 00 00 00 00 a0 00 00:01:07.549 CHECK POWER MODE
- ef 03 46 00 00 00 a0 00 00:01:07.548 SET FEATURES [Set transfer mode]
- 25 00 08 40 00 00 00 04 00:01:07.518 READ DMA EXT
- 25 00 08 40 00 00 e0 00 00:00:48.164 READ DMA EXT
- Error 9 occurred at disk power-on lifetime: 7716 hours (321 days + 12 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 10 51 08 40 00 00 00 Error: IDNF 8 sectors at LBA = 0x00000040 = 64
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 08 40 00 00 e0 00 00:00:48.164 READ DMA EXT
- 25 00 08 00 00 00 e0 00 00:00:48.164 READ DMA EXT
- 25 00 08 00 00 00 e0 00 00:00:47.066 READ DMA EXT
- e5 00 00 00 00 00 a0 00 00:00:45.954 CHECK POWER MODE
- e5 00 00 00 00 00 a0 00 00:00:37.777 CHECK POWER MODE
- Error 8 occurred at disk power-on lifetime: 7711 hours (321 days + 7 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 10 51 08 00 00 00 00 Error: IDNF 8 sectors at LBA = 0x00000000 = 0
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 08 00 00 00 e0 00 00:00:35.544 READ DMA EXT
- e5 00 00 00 00 00 a0 00 00:00:35.544 CHECK POWER MODE
- ef 03 46 00 00 00 a0 00 00:00:35.543 SET FEATURES [Set transfer mode]
- 25 00 08 00 00 00 00 04 00:00:35.513 READ DMA EXT
- 25 00 08 00 00 00 e0 00 00:00:09.128 READ DMA EXT
- SMART Extended Self-test Log (GP Log 0x07) not supported
- SMART Self-test log structure revision number 1
- No self-tests have been logged. [To run self-tests, use: smartctl -t]
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
- SCT Status Version: 3
- SCT Version (vendor specific): 256 (0x0100)
- SCT Support Level: 1
- Device State: Active (0)
- Current Temperature: 29 Celsius
- Power Cycle Min/Max Temperature: 27/29 Celsius
- Lifetime Min/Max Temperature: 15/41 Celsius
- Lifetime Average Temperature: 28 Celsius
- Under/Over Temperature Limit Count: 0/0
- SCT Temperature History Version: 2
- Temperature Sampling Period: 1 minute
- Temperature Logging Interval: 1 minute
- Min/Max recommended Temperature: 0/60 Celsius
- Min/Max Temperature Limit: -40/65 Celsius
- Temperature History Size (Index): 128 (93)
- Index Estimated Time Temperature Celsius
- 94 2018-06-20 14:50 39 ********************
- 95 2018-06-20 14:51 39 ********************
- 96 2018-06-20 14:52 38 *******************
- 97 2018-06-20 14:53 38 *******************
- 98 2018-06-20 14:54 39 ********************
- ... ..( 4 skipped). .. ********************
- 103 2018-06-20 14:59 39 ********************
- 104 2018-06-20 15:00 38 *******************
- ... ..( 2 skipped). .. *******************
- 107 2018-06-20 15:03 38 *******************
- 108 2018-06-20 15:04 39 ********************
- 109 2018-06-20 15:05 38 *******************
- 110 2018-06-20 15:06 38 *******************
- 111 2018-06-20 15:07 39 ********************
- 112 2018-06-20 15:08 38 *******************
- 113 2018-06-20 15:09 39 ********************
- 114 2018-06-20 15:10 39 ********************
- 115 2018-06-20 15:11 38 *******************
- 116 2018-06-20 15:12 39 ********************
- ... ..( 2 skipped). .. ********************
- 119 2018-06-20 15:15 39 ********************
- 120 2018-06-20 15:16 38 *******************
- 121 2018-06-20 15:17 39 ********************
- 122 2018-06-20 15:18 39 ********************
- 123 2018-06-20 15:19 38 *******************
- 124 2018-06-20 15:20 38 *******************
- 125 2018-06-20 15:21 39 ********************
- 126 2018-06-20 15:22 39 ********************
- 127 2018-06-20 15:23 38 *******************
- 0 2018-06-20 15:24 38 *******************
- 1 2018-06-20 15:25 39 ********************
- 2 2018-06-20 15:26 39 ********************
- 3 2018-06-20 15:27 38 *******************
- 4 2018-06-20 15:28 39 ********************
- ... ..( 11 skipped). .. ********************
- 16 2018-06-20 15:40 39 ********************
- 17 2018-06-20 15:41 38 *******************
- 18 2018-06-20 15:42 39 ********************
- 19 2018-06-20 15:43 39 ********************
- 20 2018-06-20 15:44 39 ********************
- 21 2018-06-20 15:45 38 *******************
- 22 2018-06-20 15:46 39 ********************
- 23 2018-06-20 15:47 38 *******************
- 24 2018-06-20 15:48 38 *******************
- 25 2018-06-20 15:49 38 *******************
- 26 2018-06-20 15:50 37 ******************
- 27 2018-06-20 15:51 36 *****************
- 28 2018-06-20 15:52 36 *****************
- 29 2018-06-20 15:53 35 ****************
- 30 2018-06-20 15:54 35 ****************
- 31 2018-06-20 15:55 34 ***************
- 32 2018-06-20 15:56 34 ***************
- 33 2018-06-20 15:57 34 ***************
- 34 2018-06-20 15:58 33 **************
- ... ..( 3 skipped). .. **************
- 38 2018-06-20 16:02 33 **************
- 39 2018-06-20 16:03 32 *************
- ... ..( 5 skipped). .. *************
- 45 2018-06-20 16:09 32 *************
- 46 2018-06-20 16:10 31 ************
- 47 2018-06-20 16:11 32 *************
- 48 2018-06-20 16:12 32 *************
- 49 2018-06-20 16:13 31 ************
- 50 2018-06-20 16:14 32 *************
- 51 2018-06-20 16:15 31 ************
- ... ..( 4 skipped). .. ************
- 56 2018-06-20 16:20 31 ************
- 57 2018-06-20 16:21 32 *************
- 58 2018-06-20 16:22 31 ************
- ... ..( 15 skipped). .. ************
- 74 2018-06-20 16:38 31 ************
- 75 2018-06-20 16:39 32 *************
- 76 2018-06-20 16:40 32 *************
- 77 2018-06-20 16:41 33 **************
- 78 2018-06-20 16:42 34 ***************
- 79 2018-06-20 16:43 34 ***************
- 80 2018-06-20 16:44 34 ***************
- 81 2018-06-20 16:45 35 ****************
- 82 2018-06-20 16:46 35 ****************
- 83 2018-06-20 16:47 36 *****************
- 84 2018-06-20 16:48 36 *****************
- 85 2018-06-20 16:49 37 ******************
- 86 2018-06-20 16:50 37 ******************
- 87 2018-06-20 16:51 36 *****************
- 88 2018-06-20 16:52 35 ****************
- 89 2018-06-20 16:53 35 ****************
- 90 2018-06-20 16:54 34 ***************
- 91 2018-06-20 16:55 ? -
- 92 2018-06-20 16:56 27 ********
- 93 2018-06-20 16:57 29 **********
- Write SCT (Get) Error Recovery Control Command failed: Read of ATA output registers not implemented [JMicron]
- SCT (Get) Error Recovery Control command failed
- Device Statistics (GP/SMART Log 0x04) not supported
- ATA_READ_LOG_EXT (addr=0x11:0x00, page=0, n=1) failed: 48-bit ATA commands not implemented [JMicron]
- Read SATA Phy Event Counters failed
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement