G2A Many GEOs
SHARE
TWEET

UDOO HDMI issue2

casperl Oct 31st, 2013 464 Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1.  
  2. U-Boot 2009.08-svn89 (Oct 29 2013 - 16:13:13)
  3.  
  4. CPU: Freescale i.MX6 family TO1.2 at 792 MHz
  5. Thermal sensor with ratio = 181
  6. Temperature:   19 C, calibration data 0x5784ed69
  7. mx6q pll1: 792MHz
  8. mx6q pll2: 528MHz
  9. mx6q pll3: 480MHz
  10. mx6q pll8: 50MHz
  11. ipg clock     : 66000000Hz
  12. ipg per clock : 66000000Hz
  13. uart clock    : 80000000Hz
  14. cspi clock    : 60000000Hz
  15. ahb clock     : 132000000Hz
  16. axi clock   : 264000000Hz
  17. emi_slow clock: 132000000Hz
  18. ddr clock     : 528000000Hz
  19. usdhc1 clock  : 198000000Hz
  20. usdhc2 clock  : 198000000Hz
  21. usdhc3 clock  : 198000000Hz
  22. usdhc4 clock  : 198000000Hz
  23. nfc clock     : 24000000Hz
  24. Board: i.MX6Q-UDOO: unknown-board Board: 0x63012 [POR]
  25. Boot Device: NOR
  26. I2C:   ready
  27. DRAM:   1 GB
  28. MMC:   FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2,FSL_USDHC: 3
  29. *** Warning - bad CRC or MMC, using default environment
  30.  
  31. In:    serial
  32. Out:   serial
  33. Err:   serial
  34. Net:   got MAC address from IIM: 00:c0:08:88:16:8a
  35. FEC0
  36. Hit any key to stop autoboot:  0
  37. mmc2 is current device
  38. Loading file "/boot/uImage" from mmc device 2:1 (xxc1)
  39. 4119096 bytes read
  40. ## Booting kernel from Legacy Image at 10800000 ...
  41.    Image Name:   Linux-3.0.35
  42.    Created:      2013-10-28  14:41:41 UTC
  43.    Image Type:   ARM Linux Kernel Image (uncompressed)
  44.    Data Size:    4119032 Bytes =  3.9 MB
  45.    Load Address: 10008000
  46.    Entry Point:  10008000
  47.    Verifying Checksum ... OK
  48.    Loading Kernel Image ... OK
  49. OK
  50.  
  51. Starting kernel ...
  52.  
  53. [    0.000000] Linux version 3.0.35 (udoo@ubuntu) (gcc version 4.4.4 (4.4.4_09.06.2010) ) #1 SMP PREEMPT Mon Oct 28 15:41:34 CET 2013
  54. [    0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
  55. [    0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
  56. [    0.000000] Machine: SECO i.Mx6 UDOO Board
  57. [    0.000000] Kernel ver: v. 87
  58. [    0.000000] Ignoring unrecognised tag 0x41000901
  59. [    0.000000] Memory policy: ECC disabled, Data cache writealloc
  60. [    0.000000] CPU identified as i.MX6Q, silicon rev 1.2
  61. [    0.000000] PERCPU: Embedded 7 pages/cpu @8c008000 s5440 r8192 d15040 u32768
  62. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 227328
  63. [    0.000000] Kernel command line: console=ttymxc1,115200 root=/dev/mmcblk0p1 rootwait rw fixrtc rootflags=barrier=1 mem=1024M arm_freq=996 video=mxcfb0:dev=hdmi,1920x1080M@60,bpp=32
  64. [    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
  65. [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  66. [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  67. [    0.000000] Memory: 640MB 256MB = 896MB total
  68. [    0.000000] Memory: 896384k/896384k available, 152192k reserved, 0K highmem
  69. [    0.000000] Virtual kernel memory layout:
  70. [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
  71. [    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
  72. [    0.000000]     DMA     : 0xf4600000 - 0xffe00000   ( 184 MB)
  73. [    0.000000]     vmalloc : 0xc0800000 - 0xf2000000   ( 792 MB)
  74. [    0.000000]     lowmem  : 0x80000000 - 0xc0000000   (1024 MB)
  75. [    0.000000]     pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
  76. [    0.000000]     modules : 0x7f000000 - 0x7fe00000   (  14 MB)
  77. [    0.000000]       .init : 0x80008000 - 0x80038000   ( 192 kB)
  78. [    0.000000]       .text : 0x80038000 - 0x80b03e8c   (11056 kB)
  79. [    0.000000]       .data : 0x80b04000 - 0x80b63b00   ( 383 kB)
  80. [    0.000000]        .bss : 0x80b63b24 - 0x80bb2480   ( 315 kB)
  81. [    0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
  82. [    0.000000] Preemptible hierarchical RCU implementation.
  83. [    0.000000] NR_IRQS:624
  84. [    0.000000] MXC GPIO hardware
  85. [    0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
  86. [    0.000000] arm_max_freq=1GHz
  87. [    0.000000] MXC_Early serial console at MMIO 0x21e8000 (options '115200')
  88. [    0.000000] bootconsole [ttymxc1] enabled
  89. [    0.000000] Console: colour dummy device 80x30
  90. [    0.223168] Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
  91. [    0.311505] pid_max: default: 32768 minimum: 301
  92. [    0.316390] Mount-cache hash table entries: 512
  93. [    0.321606] CPU: Testing write buffer coherency: ok
  94. [    0.326759] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
  95. [    0.427287] CPU1: Booted secondary processor
  96. [    0.507283] CPU2: Booted secondary processor
  97. [    0.587299] CPU3: Booted secondary processor
  98. [    0.626793] Brought up 4 CPUs
  99. [    0.642618] SMP: Total of 4 processors activated (6324.22 BogoMIPS).
  100. [    0.666175] print_constraints: dummy:
  101. [    0.670167] NET: Registered protocol family 16
  102. [    0.678941] print_constraints: vddpu: 725 <--> 1300 mV at 700 mV fast normal
  103. [    0.686396] print_constraints: vddcore: 725 <--> 1300 mV at 1150 mV fast normal
  104. [    0.694143] print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal
  105. [    0.701838] print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal
  106. [    0.709603] print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal
  107. [    0.717257] print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal
  108. [    0.726240]
  109. [    0.726246] > UDOO quad
  110. [    0.730038] > rev C Called set_gpios_direction
  111. [    0.734697] Test and set gpios directions and values by Gionji feat. Ekirei test
  112. [    0.765797] Resetting ethernet physical layer.
  113. [    0.813303] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
  114. [    0.820138] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
  115. [    0.827498] hw-breakpoint: maximum watchpoint size is 4 bytes.
  116. [    0.833384] L310 cache controller enabled
  117. [    0.837426] l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x02070000, Cache size: 1048576 B
  118. [    0.870974] bio: create slab <bio-0> at 0
  119. [    0.878251] mxs-dma mxs-dma-apbh: initialized
  120. [    0.882933] print_constraints: vmmc: 3300 mV
  121. [    0.888015] vgaarb: loaded
  122. [    0.891553] SCSI subsystem initialized
  123. [    0.896405] usbcore: registered new interface driver usbfs
  124. [    0.902061] usbcore: registered new interface driver hub
  125. [    0.907563] usbcore: registered new device driver usb
  126. [    0.912632] Freescale USB OTG Driver loaded, $Revision: 1.55 $
  127. [    0.936788] imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
  128. [    0.956794] imx-ipuv3 imx-ipuv3.1: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
  129. [    0.964671] MIPI CSI2 driver module loaded
  130. [    0.969007] Advanced Linux Sound Architecture Driver Version 1.0.24.
  131. [    0.976223] Bluetooth: Core ver 2.16
  132. [    0.979944] NET: Registered protocol family 31
  133. [    0.984401] Bluetooth: HCI device and connection manager initialized
  134. [    0.990786] Bluetooth: HCI socket layer initialized
  135. [    0.995680] Bluetooth: L2CAP socket layer initialized
  136. [    1.000829] Bluetooth: SCO socket layer initialized
  137. [    1.006146] cfg80211: Calling CRDA to update world regulatory domain
  138. [    1.013579] i2c-core: driver [max17135] using legacy suspend method
  139. [    1.019880] i2c-core: driver [max17135] using legacy resume method
  140. [    1.026097] Switching to clocksource mxc_timer1
  141. [    1.043098] NET: Registered protocol family 2
  142. [    1.047652] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
  143. [    1.055580] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
  144. [    1.064921] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
  145. [    1.072661] TCP: Hash tables configured (established 131072 bind 65536)
  146. [    1.079296] TCP reno registered
  147. [    1.082470] UDP hash table entries: 512 (order: 2, 16384 bytes)
  148. [    1.088437] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  149. [    1.095182] NET: Registered protocol family 1
  150. [    1.099838] RPC: Registered named UNIX socket transport module.
  151. [    1.105806] RPC: Registered udp transport module.
  152. [    1.110527] RPC: Registered tcp transport module.
  153. [    1.115261] RPC: Registered tcp NFSv4.1 backchannel transport module.
  154. [    1.122585] PMU: registered new PMU device of type 0
  155. [    1.127691] Static Power Management for Freescale i.MX6
  156. [    1.132956] wait mode is enabled for i.MX6
  157. [    1.137247] cpaddr = c0880000 suspend_iram_base=c08fc000
  158. [    1.142695] PM driver module loaded
  159. [    1.146579] IMX usb wakeup probe
  160. [    1.150267] add wake up source irq 75
  161. [    1.157553] IMX usb wakeup probe
  162. [    1.161076] cpu regulator mode:ldo_enable
  163. [    1.165348] i.MXC CPU frequency driver
  164. [    1.195379] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
  165. [    1.202051] msgmni has been set to 1750
  166. [    1.207441] alg: No test for stdrng (krng)
  167. [    1.211712] io scheduler noop registered
  168. [    1.215650] io scheduler deadline registered
  169. [    1.220018] io scheduler cfq registered (default)
  170. [    1.225808] MIPI DSI driver module loaded
  171. [    1.230001] mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver hdmi
  172. [    1.236522] mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0xa:0xa0:0xc1
  173. [    1.243444] fbcvt: 1920x1080@60: CVT Name - 2.073M9
  174. [    1.261052] imx-ipuv3 imx-ipuv3.0: WARNING: adapt panel end blank lines
  175. [    1.280755] imx-ipuv3 imx-ipuv3.0: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
  176. [    1.314066] imx-ipuv3 imx-ipuv3.0: WARNING: adapt panel end blank lines
  177. [    1.347449] Console: switching to colour frame buffer device 160x64
  178. [    1.395546] mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver ldb
  179. [    1.401961] _regulator_get: get() with no identifier
  180. [    1.410860] mxc_hdmi mxc_hdmi: Read EDID again
  181. [    1.415408] mxc_hdmi mxc_hdmi: No modes read from edid
  182. [    1.420563] mxc_hdmi mxc_hdmi: create default modelist
  183. [    1.428073] fbcvt: 1920x1080@60: CVT Name - 2.073M9
  184. [    1.433421] mxc_sdc_fb mxc_sdc_fb.2: register mxc display driver ldb
  185. [    1.444607] imx-sdma imx-sdma: loaded firmware 1.1
  186. [    1.448763] imx-sdma imx-sdma: initialized
  187. [    1.577481] imx-ipuv3 imx-ipuv3.0: WARNING: adapt panel end blank lines
  188. [    1.672157] Serial: IMX driver
  189. [    1.672271] imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
  190. [    1.672643] imx-uart.1: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX
  191. [    1.714234] console [ttymxc1] enabled, bootconsole disabled
  192. [    1.714234] console [ttymxc1] enabled, bootconsole disabled
  193. [    1.725905] imx-uart.3: ttymxc3 at MMIO 0x21f0000 (irq = 61) is a IMX
  194. [    1.737796] loop: module loaded
  195. [    1.740965] request BOSSA_CLK IRQ
  196. [    1.744282] registering IRQ 419 for BOSSAC Arduino erase/reset operation
  197. [    1.794611] No sata disk.
  198. [    1.798486] GPMI NAND driver registered. (IMX)
  199. [    1.803909] vcan: Virtual CAN interface driver
  200. [    1.808357] CAN device driver interface
  201. [    1.812210] flexcan netdevice driver
  202. [    1.815939] FEC Ethernet Driver
  203. [    1.821264] fec_enet_mii_bus: probed
  204. [    1.831621] usbcore: registered new interface driver rt2800usb
  205. [    1.837459] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  206. [    1.844125] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
  207. [    1.850780] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
  208. [    1.880712] fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000
  209. [    1.900716] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
  210. [    1.906946] hub 1-0:1.0: USB hub found
  211. [    1.910723] hub 1-0:1.0: 1 port detected
  212. [    1.914826] add wake up source irq 72
  213. [    1.918525] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
  214. [    1.925169] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
  215. [    1.960707] fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200
  216. [    1.980697] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
  217. [    1.986843] hub 2-0:1.0: USB hub found
  218. [    1.990605] hub 2-0:1.0: 1 port detected
  219. [    1.994901] Initializing USB Mass Storage driver...
  220. [    1.999936] usbcore: registered new interface driver usb-storage
  221. [    2.005958] USB Mass Storage support registered.
  222. [    2.010910] usbcore: registered new interface driver usbserial
  223. [    2.016851] USB Serial support registered for generic
  224. [    2.022041] usbcore: registered new interface driver usbserial_generic
  225. [    2.028571] usbserial: USB Serial Driver core
  226. [    2.033047] USB Serial support registered for debug
  227. [    2.038048] usbcore: registered new interface driver debug
  228. [    2.043549] ARC USBOTG Device Controller driver (1 August 2005)
  229. [    2.050253] mousedev: PS/2 mouse device common for all mice
  230. [    2.056856] i2c-core: driver [isl29023] using legacy suspend method
  231. [    2.063141] i2c-core: driver [isl29023] using legacy resume method
  232. [    2.070010] snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc0
  233. [    2.076693] i2c /dev entries driver
  234. [    2.081031] Linux video capture interface: v2.00
  235. [    2.086011] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16
  236. [    2.093628] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17
  237. [    2.101241] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video18
  238. [    2.108849] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video19
  239. [    2.116473] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video20
  240. [    2.124276] vivi-000: V4L2 device registered as video0
  241. [    2.129421] Video Technology Magazine Virtual Video Capture Board ver 0.8.0 successfully loaded.
  242. [    2.138598] i2c-core: driver [mag3110] using legacy suspend method
  243. [    2.144796] i2c-core: driver [mag3110] using legacy resume method
  244. [    2.151300] imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
  245. [    2.159406] Bluetooth: Virtual HCI driver ver 1.3
  246. [    2.164334] Bluetooth: HCI UART driver ver 2.2
  247. [    2.168781] Bluetooth: HCIATH3K protocol initialized
  248. [    2.173760] Bluetooth: Generic Bluetooth USB driver ver 0.6
  249. [    2.179468] usbcore: registered new interface driver btusb
  250. [    2.185115] sdhci: Secure Digital Host Controller Interface driver
  251. [    2.191310] sdhci: Copyright(c) Pierre Ossman
  252. [    2.195985] mmc0: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA
  253. [    2.203343] mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
  254. [    2.214543] VPU initialized
  255. [    2.218332] mxc_asrc registered
  256. [    2.238552] Thermal calibration data is 0x5784ed69
  257. [    2.243375] Thermal sensor with ratio = 181
  258. [    2.261381] Anatop Thermal registered as thermal_zone0
  259. [    2.266706] anatop_thermal_probe: default cooling device is cpufreq!
  260. [    2.282898] usbcore: registered new interface driver usbhid
  261. [    2.288473] usbhid: USB HID core driver
  262. [    2.292745] usbcore: registered new interface driver snd-usb-audio
  263. [    2.299469] mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio
  264. [    2.304932] Cirrus Logic CS42888 ALSA SoC Codec Driver
  265. [    2.310180] i2c-core: driver [cs42888] using legacy suspend method
  266. [    2.310714] usb 2-1: new high speed USB device number 2 using fsl-ehci
  267. [    2.323001] i2c-core: driver [cs42888] using legacy resume method
  268. [    2.355582] mmc0: new high speed SDHC card at address 9fb9
  269. [    2.361469] mmcblk0: mmc0:9fb9 SU08G 7.40 GiB
  270. [    2.367556]  mmcblk0: p1
  271. [    2.411631] audio_codec_ac97_cold_reset
  272. [    2.492076] hub 2-1:1.0: USB hub found
  273. [    2.493354] Found Audio codec AC97 vt1613, [ID = 5649 - 4123]
  274. [    2.501782] hub 2-1:1.0: 4 ports detected
  275. [    2.511499] asoc: vt1613 <-> imx-ssi.0 mapping ok
  276. [    2.517662] imx_3stack asoc driver
  277. [    2.522701] asoc: mxc-hdmi-soc <-> imx-hdmi-soc-dai.0 mapping ok
  278. [    2.529343] ALSA device list:
  279. [    2.532326]   #0: vt1613-audio
  280. [    2.535381]   #1: imx-hdmi-soc
  281. [    2.538634] NET: Registered protocol family 26
  282. [    2.543602] TCP cubic registered
  283. [    2.546834] NET: Registered protocol family 17
  284. [    2.551299] can: controller area network core (rev 20090105 abi 8)
  285. [    2.557544] NET: Registered protocol family 29
  286. [    2.561999] can: raw protocol (rev 20090105)
  287. [    2.566271] can: broadcast manager protocol (rev 20090105 t)
  288. [    2.572034] Bluetooth: RFCOMM TTY layer initialized
  289. [    2.576921] Bluetooth: RFCOMM socket layer initialized
  290. [    2.582071] Bluetooth: RFCOMM ver 1.11
  291. [    2.585822] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  292. [    2.591142] Bluetooth: BNEP filters: protocol multicast
  293. [    2.596368] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  294. [    2.602434] lib80211: common routines for IEEE802.11 drivers
  295. [    2.608130] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
  296. [    2.616165] Bus freq driver module loaded
  297. [    2.620194] Bus freq driver Enabled
  298. [    2.625468] mxc_dvfs_core_probe
  299. [    2.628814] DVFS driver module loaded
  300. [    2.634006] snvs_rtc snvs_rtc.0: setting system clock to 1970-01-01 00:00:00 UTC (0)
  301. [    2.785337] usb 2-1.3: new high speed USB device number 3 using fsl-ehci
  302. [   22.642317] kjournald starting.  Commit interval 5 seconds
  303. [   22.647263] EXT3-fs (mmcblk0p1): using internal journal
  304. [   22.647569] EXT3-fs (mmcblk0p1): 4 orphan inodes deleted
  305. [   22.647575] EXT3-fs (mmcblk0p1): recovery complete
  306. [   23.219335] EXT3-fs (mmcblk0p1): mounted filesystem with writeback data mode
  307. [   23.226431] VFS: Mounted root (ext3 filesystem) on device 179:1.
  308. [   23.232504] Freeing init memory: 192K
  309. [............] Loading cpufreq kernel modules   ...done.
  310.  * Starting bluetooth                                                    [ OK ]
  311.  * PulseAudio configured for per-user sessions
  312. [   41.364992] imx-ipuv3 imx-ipuv3.0: WARNING: adapt panel end blank lines
  313.  
  314. Ubuntu 11.10 imx6-qsdl ttymxc1
  315.  
  316. imx6-qsdl login:
RAW Paste Data
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy. OK, I Understand
Top