Guest User

Untitled

a guest
Jan 23rd, 2022
11
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 35.97 KB | None
  1.  
  2.  
  3. U-Boot 2012.07 [ ,uart_en] (Nov 02 2017 - 17:14:39)
  4.  
  5. smem ram ptable found: ver: 0 len: 5
  6. DRAM: 494 MiB
  7. NAND: SF: Unsupported manufacturer 00
  8. ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
  9. 256 MiB
  10. PCI0 Link Intialized
  11. PCI1 Link Intialized
  12. In: serial
  13. Out: serial
  14. Err: serial
  15. cdp: get part failed for 0:HLOS
  16. cdp: get part failed for rootfs
  17. Net: MAC1 addr:40:31:3c:dc:1e:b2
  18. athrs17_reg_init: complete
  19. athrs17_vlan_config ...done
  20. S17c init done
  21. MAC2 addr:40:31:3c:dc:1e:b3
  22. eth0, eth1
  23. Hit any key to stop autoboot: 0
  24.  
  25. NAND read: device 0 offset 0x800000, size 0x400000
  26. 4194304 bytes read: OK
  27. Image Name: ARM OpenWrt Linux-5.4.154
  28. Image Type: ARM Linux Kernel Image (uncompressed)
  29. Data Size: 2857847 Bytes = 2.7 MiB
  30. Load Address: 42208000
  31. Entry Point: 42208000
  32. Verifying Checksum ... OK
  33. Loading Kernel Image ... OK
  34. OK
  35.  
  36. device nand0 <nand>, # parts = 9
  37. #: name size offset mask_flags
  38. 0: Bdata 0x00080000 0x00600000 0
  39. 1: crash 0x00080000 0x00680000 0
  40. 2: crash_syslog 0x00080000 0x00700000 0
  41. 3: rsvd 0x00080000 0x00780000 0
  42. 4: kernel0 0x00400000 0x00800000 0
  43. 5: kernel1 0x00400000 0x00c00000 0
  44. 6: rootfs0 0x02800000 0x01000000 0
  45. 7: rootfs1 0x02800000 0x03800000 0
  46. 8: overlay 0x0a000000 0x06000000 0
  47.  
  48. active partition: nand0,0 - (Bdata) 0x00080000 @ 0x00600000
  49.  
  50. defaults:
  51. mtdids : none
  52. mtdparts: none
  53. Setting up atags for msm partition: Bdata
  54. Setting up atags for msm partition: crash
  55. Setting up atags for msm partition: crash_syslog
  56. Setting up atags for msm partition: rsvd
  57. Setting up atags for msm partition: kernel0
  58. Setting up atags for msm partition: kernel1
  59. Setting up atags for msm partition: rootfs0
  60. Setting up atags for msm partition: rootfs1
  61. Setting up atags for msm partition: overlay
  62. Using machid 0x1260 from environment
  63.  
  64. Starting kernel ...
  65.  
  66. [ 0.000000] Booting Linux on physical CPU 0x0
  67. [ 0.000000] Linux version 5.4.154 (droid@droid-vm) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16325-88151b8303)) #0 SMP Sun Oct 24 09:01:35 2021
  68. [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
  69. [ 0.000000] CPU: div instructions available: patching division code
  70. [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
  71. [ 0.000000] OF: fdt: Machine model: Xiaomi Mi Router HD (R3D)
  72. [ 0.000000] Memory policy: Data cache writealloc
  73. [ 0.000000] On node 0 totalpages: 122368
  74. [ 0.000000] Normal zone: 1080 pages used for memmap
  75. [ 0.000000] Normal zone: 0 pages reserved
  76. [ 0.000000] Normal zone: 122368 pages, LIFO batch:31
  77. [ 0.000000] percpu: Embedded 15 pages/cpu s30156 r8192 d23092 u61440
  78. [ 0.000000] pcpu-alloc: s30156 r8192 d23092 u61440 alloc=15*4096
  79. [ 0.000000] pcpu-alloc: [0] 0 [0] 1
  80. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121288
  81. [ 0.000000] Kernel command line: rootfstype=squashfs noinitrd
  82. [ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8 uart_en=1
  83. [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
  84. [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
  85. [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
  86. [ 0.000000] Memory: 474836K/489472K available (6108K kernel code, 193K rwdata, 1532K rodata, 1024K init, 231K bss, 14636K reserved, 0K cma-reserved, 0K highmem)
  87. [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  88. [ 0.000000] rcu: Hierarchical RCU implementation.
  89. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
  90. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
  91. [ 0.000000] random: get_random_bytes called from start_kernel+0x340/0x4ec with crng_init=0
  92. [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
  93. [ 0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
  94. [ 0.000023] Switching to timer-based delay loop, resolution 160ns
  95. [ 0.000264] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
  96. [ 0.000284] pid_max: default: 32768 minimum: 301
  97. [ 0.000487] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
  98. [ 0.000508] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
  99. [ 0.001547] CPU: Testing write buffer coherency: ok
  100. [ 0.002695] Setting up static identity map for 0x42300000 - 0x42300060
  101. [ 0.002880] rcu: Hierarchical SRCU implementation.
  102. [ 0.003368] smp: Bringing up secondary CPUs ...
  103. [ 0.005308] smp: Brought up 1 node, 2 CPUs
  104. [ 0.005327] SMP: Total of 2 processors activated (25.00 BogoMIPS).
  105. [ 0.005337] CPU: All CPU(s) started in SVC mode.
  106. [ 0.015833] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
  107. [ 0.015995] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  108. [ 0.016026] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
  109. [ 0.016168] pinctrl core: initialized pinctrl subsystem
  110. [ 0.017324] NET: Registered protocol family 16
  111. [ 0.017630] DMA: preallocated 256 KiB pool for atomic coherent allocations
  112. [ 0.018999] cpuidle: using governor ladder
  113. [ 0.019066] cpuidle: using governor menu
  114. [ 0.050623] usbcore: registered new interface driver usbfs
  115. [ 0.050704] usbcore: registered new interface driver hub
  116. [ 0.050772] usbcore: registered new device driver usb
  117. [ 0.050842] pps_core: LinuxPPS API ver. 1 registered
  118. [ 0.050855] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  119. [ 0.050896] PTP clock support registered
  120. [ 0.051858] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
  121. [ 0.052959] clocksource: Switched to clocksource dg_timer
  122. [ 0.053836] thermal_sys: Registered thermal governor 'step_wise'
  123. [ 0.056231] NET: Registered protocol family 2
  124. [ 0.056403] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
  125. [ 0.057077] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
  126. [ 0.057119] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
  127. [ 0.057164] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
  128. [ 0.057217] TCP: Hash tables configured (established 4096 bind 4096)
  129. [ 0.057322] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
  130. [ 0.057355] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
  131. [ 0.057608] NET: Registered protocol family 1
  132. [ 0.057665] PCI: CLS 0 bytes, default 64
  133. [ 0.059048] workingset: timestamp_bits=14 max_order=17 bucket_order=3
  134. [ 0.066148] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  135. [ 0.066165] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  136. [ 0.107395] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator
  137. [ 0.107545] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator
  138. [ 0.107664] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator
  139. [ 0.107932] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
  140. [ 0.107956] qcom-pcie 1b500000.pci: Parsing ranges property...
  141. [ 0.108007] qcom-pcie 1b500000.pci: IO 0x0fe00000..0x0fefffff -> 0x0fe00000
  142. [ 0.108045] qcom-pcie 1b500000.pci: MEM 0x08000000..0x0fdfffff -> 0x08000000
  143. [ 0.328625] qcom-pcie 1b500000.pci: Link up
  144. [ 0.328791] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
  145. [ 0.328814] pci_bus 0000:00: root bus resource [bus 00-ff]
  146. [ 0.328834] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
  147. [ 0.328850] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
  148. [ 0.328868] pci_bus 0000:00: scanning bus
  149. [ 0.328922] pci 0000:00:00.0: [17cb:0101] type 01 class 0xff0000
  150. [ 0.329090] pci 0000:00:00.0: supports D1
  151. [ 0.329105] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
  152. [ 0.329124] pci 0000:00:00.0: PME# disabled
  153. [ 0.333384] pci_bus 0000:00: fixups for bus
  154. [ 0.333411] PCI: bus0: Fast back to back transfers disabled
  155. [ 0.333431] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
  156. [ 0.333585] pci_bus 0000:01: scanning bus
  157. [ 0.333768] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000
  158. [ 0.334123] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
  159. [ 0.335267] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
  160. [ 0.335315] pci 0000:01:00.0: PME# disabled
  161. [ 0.339607] pci_bus 0000:01: fixups for bus
  162. [ 0.339683] PCI: bus1: Fast back to back transfers disabled
  163. [ 0.339699] pci_bus 0000:01: bus scan returning with max=01
  164. [ 0.339720] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
  165. [ 0.339741] pci_bus 0000:00: bus scan returning with max=ff
  166. [ 0.339779] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
  167. [ 0.339803] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
  168. [ 0.339934] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
  169. [ 0.339960] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
  170. [ 0.340173] pcieport 0000:00:00.0: assign IRQ: got 35
  171. [ 0.340944] pcieport 0000:00:00.0: AER: enabled with IRQ 36
  172. [ 0.341534] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator
  173. [ 0.341659] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator
  174. [ 0.341792] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator
  175. [ 0.342048] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
  176. [ 0.342071] qcom-pcie 1b700000.pci: Parsing ranges property...
  177. [ 0.342117] qcom-pcie 1b700000.pci: IO 0x31e00000..0x31efffff -> 0x31e00000
  178. [ 0.342152] qcom-pcie 1b700000.pci: MEM 0x2e000000..0x31dfffff -> 0x2e000000
  179. [ 0.570452] qcom-pcie 1b700000.pci: Link up
  180. [ 0.570610] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
  181. [ 0.570629] pci_bus 0001:00: root bus resource [bus 00-ff]
  182. [ 0.570645] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
  183. [ 0.570661] pci_bus 0001:00: scanning bus
  184. [ 0.570711] pci 0001:00:00.0: [17cb:0101] type 01 class 0xff0000
  185. [ 0.570860] pci 0001:00:00.0: supports D1
  186. [ 0.570875] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
  187. [ 0.570893] pci 0001:00:00.0: PME# disabled
  188. [ 0.575116] pci_bus 0001:00: fixups for bus
  189. [ 0.575141] PCI: bus0: Fast back to back transfers disabled
  190. [ 0.575160] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
  191. [ 0.575300] pci_bus 0001:01: scanning bus
  192. [ 0.575496] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000
  193. [ 0.575872] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
  194. [ 0.577104] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
  195. [ 0.577152] pci 0001:01:00.0: PME# disabled
  196. [ 0.577409] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0001:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
  197. [ 0.581497] pci_bus 0001:01: fixups for bus
  198. [ 0.581581] PCI: bus1: Fast back to back transfers disabled
  199. [ 0.581595] pci_bus 0001:01: bus scan returning with max=01
  200. [ 0.581617] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
  201. [ 0.581638] pci_bus 0001:00: bus scan returning with max=ff
  202. [ 0.581667] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
  203. [ 0.581690] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
  204. [ 0.581821] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
  205. [ 0.581845] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
  206. [ 0.582029] pcieport 0001:00:00.0: assign IRQ: got 37
  207. [ 0.582764] pcieport 0001:00:00.0: AER: enabled with IRQ 38
  208. [ 0.585408] L2 @ QSB rate. Forcing new rate.
  209. [ 0.585632] L2 @ 384000 KHz
  210. [ 0.585812] CPU0 @ 800000 KHz
  211. [ 0.585825] CPU1 @ QSB rate. Forcing new rate.
  212. [ 0.585950] CPU1 @ 384000 KHz
  213. [ 0.589619] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
  214. [ 0.591792] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
  215. [ 0.592616] msm_serial 16340000.serial: msm_serial: detected port #0
  216. [ 0.592667] msm_serial 16340000.serial: uartclk = 7372800
  217. [ 0.592738] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 39, base_baud = 460800) is a MSM
  218. [ 0.592776] msm_serial: console setup on port #0
  219. [ 1.526760] printk: console [ttyMSM0] enabled
  220. [ 1.531703] msm_serial: driver initialized
  221. [ 1.541084] loop: module loaded
  222. [ 1.542688] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xaa
  223. [ 1.543036] nand: Macronix MX30UF2G18AC
  224. [ 1.549738] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
  225. [ 1.553468] 19 fixed-partitions partitions found on MTD device qcom_nand.0
  226. [ 1.560832] Creating 19 MTD partitions on "qcom_nand.0":
  227. [ 1.567797] 0x000000000000-0x000000040000 : "SBL1"
  228. [ 1.574667] 0x000000040000-0x0000000c0000 : "MIBIB"
  229. [ 1.579486] 0x0000000c0000-0x000000140000 : "SBL2"
  230. [ 1.584340] 0x000000140000-0x0000001c0000 : "SBL3"
  231. [ 1.589104] 0x0000001c0000-0x000000240000 : "DDRCONFIG"
  232. [ 1.593995] 0x000000240000-0x0000002c0000 : "SSD"
  233. [ 1.599029] 0x0000002c0000-0x000000340000 : "TZ"
  234. [ 1.602866] random: fast init done
  235. [ 1.607862] 0x000000340000-0x0000003c0000 : "RPM"
  236. [ 1.611753] 0x0000003c0000-0x0000004c0000 : "APPSBL"
  237. [ 1.617460] 0x0000004c0000-0x000000540000 : "APPSBLENV"
  238. [ 1.621573] 0x000000540000-0x0000005c0000 : "ART"
  239. [ 1.626621] 0x0000005c0000-0x000000600000 : "BOOTCONFIG"
  240. [ 1.631015] 0x000000600000-0x000000680000 : "bdata"
  241. [ 1.636885] 0x000000680000-0x000000700000 : "crash"
  242. [ 1.641379] 0x000000700000-0x000000780000 : "crash_syslog"
  243. [ 1.646329] 0x000000780000-0x000000800000 : "rsvd"
  244. [ 1.651788] 0x000000800000-0x000000c00000 : "kernel_dup"
  245. [ 1.662321] 0x000000c00000-0x000001000000 : "kernel"
  246. [ 1.669839] 0x000001000000-0x000010000000 : "ubi"
  247. [ 1.942668] random: crng init done
  248. [ 2.058868] libphy: ipq8064_mdio_bus: probed
  249. [ 2.079486] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii
  250. [ 2.920980] ar8327: qca,phy-rgmii-en is not specified
  251. [ 2.921556] libphy: Fixed MDIO Bus: probed
  252. [ 2.925755] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found
  253. [ 2.929014] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found
  254. [ 2.937064] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
  255. [ 2.943295] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
  256. [ 2.949154] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000
  257. [ 2.956705] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
  258. [ 2.962432] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
  259. [ 2.970247] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
  260. [ 2.978119] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
  261. [ 2.983928] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
  262. [ 2.991250] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
  263. [ 2.998079] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
  264. [ 3.005642] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
  265. [ 3.012600] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
  266. [ 3.019747] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
  267. [ 3.027557] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
  268. [ 3.034724] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
  269. [ 3.041256] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
  270. [ 3.047518] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000
  271. [ 3.054941] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
  272. [ 3.060695] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
  273. [ 3.068495] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
  274. [ 3.076397] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
  275. [ 3.082134] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
  276. [ 3.089581] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
  277. [ 3.096360] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
  278. [ 3.103920] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
  279. [ 3.110865] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
  280. [ 3.118140] i2c /dev entries driver
  281. [ 3.128142] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
  282. [ 3.129027] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
  283. [ 3.136871] sdhci: Secure Digital Host Controller Interface driver
  284. [ 3.143594] sdhci: Copyright(c) Pierre Ossman
  285. [ 3.149749] sdhci-pltfm: SDHCI platform and OF driver helper
  286. [ 3.156525] NET: Registered protocol family 10
  287. [ 3.161266] Segment Routing with IPv6
  288. [ 3.164358] NET: Registered protocol family 17
  289. [ 3.167969] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
  290. [ 3.172455] 8021q: 802.1Q VLAN Support v1.8
  291. [ 3.185514] Registering SWP/SWPB emulation handler
  292. [ 3.214056] qcom_rpm 108000.rpm: RPM firmware 3.0.16777372
  293. [ 3.227800] s1a: Bringing 0uV into 1050000-1050000uV
  294. [ 3.228088] s1a: supplied by regulator-dummy
  295. [ 3.231966] s1b: Bringing 0uV into 1050000-1050000uV
  296. [ 3.236423] s1b: supplied by regulator-dummy
  297. [ 3.241165] s2a: Bringing 0uV into 800000-800000uV
  298. [ 3.245596] s2a: supplied by regulator-dummy
  299. [ 3.250035] s2b: Bringing 0uV into 800000-800000uV
  300. [ 3.254630] s2b: supplied by regulator-dummy
  301. [ 3.268983] UBI: auto-attach mtd18
  302. [ 3.269004] ubi0: attaching mtd18
  303. [ 6.376991] ubi0: scanning is finished
  304. [ 6.388149] ubi0: attached mtd18 (name "ubi", size 240 MiB)
  305. [ 6.388170] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
  306. [ 6.392519] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
  307. [ 6.399518] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
  308. [ 6.406399] ubi0: good PEBs: 1919, bad PEBs: 1, corrupted PEBs: 0
  309. [ 6.413091] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
  310. [ 6.419415] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1641775890
  311. [ 6.426536] ubi0: available PEBs: 0, total reserved PEBs: 1919, PEBs reserved for bad PEB handling: 39
  312. [ 6.436018] ubi0: background thread "ubi_bgt0d" started, PID 69
  313. [ 6.445596] block ubiblock0_0: created from ubi0:0(rootfs)
  314. [ 6.450675] ubiblock: device ubiblock0_0 (rootfs) set to be root filesâ–’[ 6.468319] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
  315. [ 6.469919] Freeing unused kernel memory: 1024K
  316. [ 6.503575] Run /sbin/init as init process
  317. [ 6.982873] init: Console is alive
  318. [ 6.983006] init: - watchdog -
  319. [ 8.899703] kmodloader: loading kernel modules from /etc/modules-boot.d/*
  320. [ 9.090463] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  321. [ 9.093725] SCSI subsystem initialized
  322. [ 9.100186] libata version 3.00 loaded.
  323. [ 9.102165] ahci 29000000.sata: 29000000.sata supply ahci not found, using dummy regulator
  324. [ 9.103502] ahci 29000000.sata: 29000000.sata supply phy not found, using dummy regulator
  325. [ 9.111746] ahci 29000000.sata: 29000000.sata supply target not found, using dummy regulator
  326. [ 9.120918] ahci 29000000.sata: forcing port_map 0x0 -> 0x1
  327. [ 9.128519] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
  328. [ 9.133797] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
  329. [ 9.143024] scsi host0: ahci
  330. [ 9.150859] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 26
  331. [ 9.486504] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
  332. [ 9.487755] ata1.00: ATA-8: ST1000VM002-1SD102, SC11, max UDMA/133
  333. [ 9.491596] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32)
  334. [ 9.513133] ata1.00: configured for UDMA/133
  335. [ 9.513548] scsi 0:0:0:0: Direct-Access ATA ST1000VM002-1SD1 SC11 PQ: 0 ANSI: 5
  336. [ 9.519709] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
  337. [ 9.524630] sd 0:0:0:0: [sda] 4096-byte physical blocks
  338. [ 9.532191] sd 0:0:0:0: [sda] Write Protect is off
  339. [ 9.537203] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
  340. [ 9.542080] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
  341. [ 9.585829] sda: sda1
  342. [ 9.588213] sd 0:0:0:0: [sda] Attached SCSI disk
  343. [ 9.589937] ehci-fsl: Freescale EHCI Host controller driver
  344. [ 9.593918] ehci-platform: EHCI generic platform driver
  345. [ 9.606859] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  346. [ 9.607380] ohci-platform: OHCI generic platform driver
  347. [ 9.613345] dwc3-qcom 110f8800.usb3: IRQ hs_phy_irq not found
  348. [ 9.617046] dwc3-qcom 110f8800.usb3: IRQ dp_hs_phy_irq not found
  349. [ 9.622949] dwc3-qcom 110f8800.usb3: IRQ dm_hs_phy_irq not found
  350. [ 9.629132] dwc3-qcom 110f8800.usb3: IRQ ss_phy_irq not found
  351. [ 9.636729] dwc3-qcom 100f8800.usb3: IRQ hs_phy_irq not found
  352. [ 9.640657] dwc3-qcom 100f8800.usb3: IRQ dp_hs_phy_irq not found
  353. [ 9.646464] dwc3-qcom 100f8800.usb3: IRQ dm_hs_phy_irq not found
  354. [ 9.652465] dwc3-qcom 100f8800.usb3: IRQ ss_phy_irq not found
  355. [ 9.661266] dwc3 11000000.dwc3: Failed to get clk 'ref': -2
  356. [ 9.723993] dwc3 10000000.dwc3: Failed to get clk 'ref': -2
  357. [ 9.799169] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  358. [ 9.799277] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
  359. [ 9.804020] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
  360. [ 9.811234] xhci-hcd xhci-hcd.0.auto: irq 42, io mem 0x11000000
  361. [ 9.821117] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  362. [ 9.826527] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
  363. [ 9.831971] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
  364. [ 9.840335] hub 1-0:1.0: USB hub found
  365. [ 9.846210] hub 1-0:1.0: 1 port detected
  366. [ 9.850160] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
  367. [ 9.855046] hub 2-0:1.0: USB hub found
  368. [ 9.861999] hub 2-0:1.0: 1 port detected
  369. [ 9.865889] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
  370. [ 9.869623] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
  371. [ 9.875122] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
  372. [ 9.882494] xhci-hcd xhci-hcd.1.auto: irq 43, io mem 0x10000000
  373. [ 9.892077] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
  374. [ 9.897810] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
  375. [ 9.903367] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
  376. [ 9.911316] hub 3-0:1.0: USB hub found
  377. [ 9.917552] hub 3-0:1.0: 1 port detected
  378. [ 9.921438] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
  379. [ 9.926891] hub 4-0:1.0: USB hub found
  380. [ 9.933429] hub 4-0:1.0: 1 port detected
  381. [ 9.939493] usbcore: registered new interface driver usb-storage
  382. [ 9.941062] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
  383. [ 9.956612] init: - preinit -
  384. [ 11.731347] dwmac1000: Master AXI performs any burst length
  385. [ 11.731405] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
  386. [ 11.735857] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
  387. [ 11.744048] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
  388. [ 11.752763] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
  389. [ 11.761211] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
  390. [ 11.761232] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
  391. Press the [f] key and hit [enter] to enter failsafe mode
  392. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  393. [ 15.958963] mount_root: loading kmods from internal overlay
  394. [ 15.975025] kmodloader: loading kernel modules from //etc/modules-boot.d/*
  395. [ 15.976464] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
  396. [ 16.843933] UBIFS (ubi0:1): Mounting in unauthenticated mode
  397. [ 16.844374] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 162
  398. [ 16.938542] UBIFS (ubi0:1): recovery needed
  399. [ 17.153131] UBIFS (ubi0:1): recovery completed
  400. [ 17.153235] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
  401. [ 17.156513] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
  402. [ 17.164414] UBIFS (ubi0:1): FS size: 226017280 bytes (215 MiB, 1780 LEBs), journal size 11300864 bytes (10 MiB, 89 LEBs)
  403. [ 17.174325] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
  404. [ 17.185251] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 70DD4A21-EA05-4DE9-926C-28601CEF8113, small LPT model
  405. [ 17.203952] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
  406. [ 17.210693] block: extroot: not configured
  407. [ 17.210865] UBIFS (ubi0:1): un-mount UBI device 0
  408. [ 17.214013] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
  409. [ 17.222462] UBIFS (ubi0:1): Mounting in unauthenticated mode
  410. [ 17.233535] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 163
  411. [ 17.410204] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
  412. [ 17.410234] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
  413. [ 17.417088] UBIFS (ubi0:1): FS size: 226017280 bytes (215 MiB, 1780 LEBs), journal size 11300864 bytes (10 MiB, 89 LEBs)
  414. [ 17.426999] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
  415. [ 17.437891] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 70DD4A21-EA05-4DE9-926C-28601CEF8113, small LPT model
  416. [ 17.448521] mount_root: loading kmods from internal overlay
  417. [ 17.472360] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
  418. [ 17.474489] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
  419. [ 18.178821] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
  420. [ 18.182801] block: extroot: not configured
  421. [ 18.188823] mount_root: switching to ubifs overlay
  422. [ 18.202649] urandom-seed: Seeding with /etc/urandom.seed
  423. [ 18.265763] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
  424. [ 18.324070] procd: - early -
  425. [ 18.324221] procd: - watchdog -
  426. [ 18.902575] procd: - watchdog -
  427. [ 18.906993] procd: - ubus -
  428. [ 18.967720] procd: - init -
  429. Please press Enter to activate this console.
  430. [ 19.465889] urngd: v1.0.2 started.
  431. [ 19.523134] kmodloader: loading kernel modules from /etc/modules.d/*
  432. [ 19.549284] Key type cifs.idmap registered
  433. [ 19.558780] ntfs: driver 2.1.32 [Flags: R/O MODULE].
  434. [ 19.564241] tun: Universal TUN/TAP device driver, 1.6
  435. [ 19.571031] l2tp_core: L2TP core driver, V2.0
  436. [ 19.571799] l2tp_netlink: L2TP netlink interface
  437. [ 19.575579] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
  438. [ 19.580231] gre: GRE over IPv4 demultiplexor driver
  439. [ 19.585591] ip_gre: GRE over IPv4 tunneling driver
  440. [ 19.591556] ip6_gre: GRE over IPv6 tunneling driver
  441. [ 19.640771] i2c-gpio i2c_gpio_0: using lines 496 (SDA) and 497 (SCL)
  442. [ 19.641083] i2c-gpio i2c_gpio_1: using lines 467 (SDA) and 468 (SCL)
  443. [ 19.648488] Bridge firewalling registered
  444. [ 19.653057] Loading modules backported from Linux version v5.10.68-0-g4d8524048a35
  445. [ 19.656552] Backport generated by backports.git v5.10.68-1-0-ga4f9ba32
  446. [ 19.687495] xt_time: kernel timezone is -0000
  447. [ 19.714372] emc2305 0-002f: emc2301 detected
  448. [ 19.717771] lm75 1-0048: hwmon1: sensor 'tmp75'
  449. [ 19.784850] PPP generic driver version 2.4.2
  450. [ 19.785797] PPP MPPE Compression module registered
  451. [ 19.788819] NET: Registered protocol family 24
  452. [ 19.793663] PPTP driver version 0.8.5
  453. [ 19.816585] ath10k_pci 0000:01:00.0: assign IRQ: got 35
  454. [ 19.816619] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46.
  455. [ 19.821123] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
  456. [ 19.828733] ath10k_pci 0000:01:00.0: enabling bus mastering
  457. [ 19.835229] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
  458. [ 22.164087] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
  459. [ 22.164121] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
  460. [ 22.174881] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5
  461. [ 24.500304] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 85498734
  462. [ 28.049019] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
  463. [ 28.049047] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
  464. [ 28.131541] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
  465. [ 28.132390] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
  466. [ 28.422014] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
  467. [ 28.515345] ath: EEPROM regdomain sanitized
  468. [ 28.515385] ath: EEPROM regdomain: 0x64
  469. [ 28.518340] ath: EEPROM indicates we should expect a direct regpair map
  470. [ 28.522176] ath: Country alpha2 being used: 00
  471. [ 28.528911] ath: Regpair used: 0x64
  472. [ 28.539126] ath10k_pci 0001:01:00.0: assign IRQ: got 37
  473. [ 28.539186] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x40.
  474. [ 28.544550] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
  475. [ 28.551246] ath10k_pci 0001:01:00.0: enabling bus mastering
  476. [ 28.557988] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
  477. [ 29.278969] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
  478. [ 29.279029] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
  479. [ 29.292393] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9980-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 b36a12bf
  480. [ 29.367074] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:2 crc32 08fa09f2
  481. [ 30.518708] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
  482. [ 30.518737] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
  483. [ 30.596830] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
  484. [ 30.597609] ath10k_pci 0001:01:00.0: wmi print 'free: 31080 iram: 23028 sram: 9596'
  485. [ 30.940470] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
  486. [ 31.035294] ath: EEPROM regdomain sanitized
  487. [ 31.035337] ath: EEPROM regdomain: 0x64
  488. [ 31.038293] ath: EEPROM indicates we should expect a direct regpair map
  489. [ 31.042129] ath: Country alpha2 being used: 00
  490. [ 31.048852] ath: Regpair used: 0x64
  491. [ 31.063799] l2tp_ppp: PPPoL2TP kernel driver, V2.0
  492. [ 31.067665] kmodloader: done loading kernel modules from /etc/modules.d/*
  493. [ 34.774517] dwmac1000: Master AXI performs any burst length
  494. [ 34.774554] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
  495. [ 34.778898] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
  496. [ 34.787126] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
  497. [ 34.796027] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
  498. [ 34.802945] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
  499. [ 34.808524] br-lan: port 1(eth1.1) entered blocking state
  500. [ 34.820318] br-lan: port 1(eth1.1) entered disabled state
  501. [ 34.825841] device eth1.1 entered promiscuous mode
  502. [ 34.830968] device eth1 entered promiscuous mode
  503. [ 34.836689] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
  504. [ 34.840834] br-lan: port 1(eth1.1) entered blocking state
  505. [ 34.846507] br-lan: port 1(eth1.1) entered forwarding state
  506. [ 34.858590] dwmac1000: Master AXI performs any burst length
  507. [ 34.858620] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
  508. [ 34.862985] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
  509. [ 34.871167] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
  510. [ 34.880070] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
  511. [ 34.887609] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
  512. [ 34.895608] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  513. [ 35.732489] ath: EEPROM regdomain: 0x824f
  514. [ 35.732518] ath: EEPROM indicates we should expect a country code
  515. [ 35.735565] ath: doing EEPROM country->regdmn map search
  516. [ 35.741545] ath: country maps to regdmn code: 0x10
  517. [ 35.746994] ath: Country alpha2 being used: PA
  518. [ 35.751534] ath: Regpair used: 0x10
  519. [ 35.756024] ath: regdomain 0x824f dynamically updated by user
  520. [ 35.759366] ath: EEPROM regdomain: 0x824f
  521. [ 35.765299] ath: EEPROM indicates we should expect a country code
  522. [ 35.769238] ath: doing EEPROM country->regdmn map search
  523. [ 35.775359] ath: country maps to regdmn code: 0x10
  524. [ 35.780693] ath: Country alpha2 being used: PA
  525. [ 35.785355] ath: Regpair used: 0x10
  526. [ 35.789721] ath: regdomain 0x824f dynamically updated by user
  527. [ 35.844848] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  528. [ 43.241837] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
  529. [ 43.241867] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
  530. [ 43.323974] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
  531. [ 43.324791] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
  532. [ 43.708238] ath10k_pci 0000:01:00.0: rts threshold -1
  533. [ 43.709862] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
  534. [ 43.731998] br-lan: port 2(wlan0-1) entered blocking state
  535. [ 43.732023] br-lan: port 2(wlan0-1) entered disabled state
  536. [ 43.736651] device wlan0-1 entered promiscuous mode
  537. [ 43.789859] ath10k_pci 0000:01:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
  538. [ 44.808133] ath10k_pci 0000:01:00.0: mac-vif-chan had error in htt_rx_h_vdev_channel, peer-id: 0 vdev-id: 0 peer-addr: 42:31:3c:dc:1e:b5.
  539. [ 44.870600] ath10k_pci 0000:01:00.0: rts threshold -1
  540. [ 46.501920] wlan0: authenticate with ec:41:18:f5:25:82
  541. [ 46.767764] wlan0: send auth to ec:41:18:f5:25:82 (try 1/3)
  542. [ 46.776174] wlan0: authenticated
  543. [ 46.783443] wlan0: associate with ec:41:18:f5:25:82 (try 1/3)
  544. [ 46.791384] wlan0: RX AssocResp from ec:41:18:f5:25:82 (capab=0x11 status=0 aid=1)
  545. [ 46.792386] ath10k_pci 0000:01:00.0: pdev param 0 not supported by firmware
  546. [ 46.797956] ath10k_pci 0000:01:00.0: failed to enable peer stats info: -95
  547. [ 46.805065] wlan0: associated
  548. [ 46.825959] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
  549. [ 46.826792] ath10k_pci 0000:01:00.0: Invalid peer id 0 or peer stats buffer, peer: 331228c0 sta: 00000000
  550. [ 46.893497] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
  551. [ 46.893647] br-lan: port 2(wlan0-1) entered blocking state
  552. [ 46.898931] br-lan: port 2(wlan0-1) entered forwarding state
  553.  
RAW Paste Data Copied