API tools faq
paste
Advertisement
Guest User

Untitled

a guest
May 8th, 2013
203
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 22.11 KB | None | 0 0
raw download clone embed print report
  1. __ __ _ _
  2. | \/ | __ _ _ ____ _____| | |
  3. | |\/| |/ _` | '__\ \ / / _ \ | |
  4. | | | | (_| | | \ V / __/ | |
  5. |_| |_|\__,_|_| \_/ \___|_|_|
  6. _ _ ____ _
  7. | | | | | __ ) ___ ___ | |_
  8. | | | |___| _ \ / _ \ / _ \| __|
  9. | |_| |___| |_) | (_) | (_) | |_
  10. \___/ |____/ \___/ \___/ \__|
  11. ** MARVELL BOARD: RD-88F6281A LE
  12.  
  13. U-Boot 1.1.4 (Jun 8 2011 - 18:48:37) Marvell version: 3.4.19
  14.  
  15. U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFEE0
  16.  
  17. Soc: 88F6281 A1 (DDR2)
  18. CPU running @ 1200Mhz L2 running @ 400Mhz
  19. SysClock = 400Mhz , TClock = 200Mhz
  20.  
  21. DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
  22. DRAM CS[0] base 0x00000000 size 256MB
  23. DRAM Total size 256MB 16bit width
  24. Addresses 10M - 0M are saved for the U-Boot usage.
  25. Mem malloc Initialization (10M - 7M): Done
  26. NAND:128 MB
  27. Flash: 0 kB
  28.  
  29. CPU : Marvell Feroceon (Rev 1)
  30. Kernel address is 0xc80000.
  31.  
  32. Streaming disabled
  33. Write allocate disabled
  34.  
  35. Module 0 is RGMII
  36. Module 1 is TDM
  37.  
  38. USB 0: host mode
  39. PEX 0: PCI Express Root Complex Interface
  40. PEX interface detected Link X1
  41. Net: egiga0, egiga1 [PRIME]
  42. Hit any key to stop autoboot: 0
  43.  
  44. Reset IDE:
  45. Marvell Serial ATA Adapter
  46. Integrated Sata device found
  47. [0 0 0]: Enable DMA mode (6)
  48. Device 0 @ 0 0:
  49. Model: ST9250315AS Firm: 0001SDM1 Ser#: 5VCK0T4C
  50. Type: Hard Disk
  51. Supports 48-bit addressing
  52. Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
  53.  
  54.  
  55. 3271488 bytes read
  56. ## Booting image at 02000000 ...
  57. Image Name: Linux-3.8.11-2-ARCH
  58. Created: 2013-05-07 19:55:04 UTC
  59. Image Type: ARM Linux Kernel Image (uncompressed)
  60. Data Size: 3271424 Bytes = 3.1 MB
  61. Load Address: 00008000
  62. Entry Point: 00008000
  63. Verifying Checksum ... OK
  64. OK
  65.  
  66. Starting kernel ...
  67.  
  68. Uncompressing Linux... done, booting the kernel.
  69. [ 0.000000] Booting Linux on physical CPU 0x0
  70. [ 0.000000] Initializing cgroup subsys cpuset
  71. [ 0.000000] Initializing cgroup subsys cpu
  72. [ 0.000000] Linux version 3.8.11-2-ARCH (root@alarmts) (gcc version 4.7.2 (GCC) ) #1 PREEMPT Tue May 7 14:54:32 CDT 2013
  73. [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
  74. [ 0.000000] CPU: VIVT data cache, VIVT instruction cache
  75. [ 0.000000] Machine: ZyXEL NSA310 1-Bay Power Media Server
  76. [ 0.000000] Memory policy: ECC disabled, Data cache writeback
  77. [ 0.000000] On node 0 totalpages: 65536
  78. [ 0.000000] free_area_init_node: node 0, pgdat c06699fc, node_mem_map c073b000
  79. [ 0.000000] Normal zone: 512 pages used for memmap
  80. [ 0.000000] Normal zone: 0 pages reserved
  81. [ 0.000000] Normal zone: 65024 pages, LIFO batch:15
  82. [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
  83. [ 0.000000] pcpu-alloc: [0] 0
  84. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
  85. [ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(
  86. rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/sda2 rw rootwait loglevel=8
  87. [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
  88. [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
  89. [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
  90. [ 0.000000] __ex_table already sorted, skipping sort
  91. [ 0.000000] Memory: 256MB = 256MB total
  92. [ 0.000000] Memory: 252452k/252452k available, 9692k reserved, 0K highmem
  93. [ 0.000000] Virtual kernel memory layout:
  94. [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  95. [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  96. [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
  97. [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
  98. [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
  99. [ 0.000000] .text : 0xc0008000 - 0xc05f8c80 (6084 kB)
  100. [ 0.000000] .init : 0xc05f9000 - 0xc0625dfc ( 180 kB)
  101. [ 0.000000] .data : 0xc0626000 - 0xc066dd98 ( 288 kB)
  102. [ 0.000000] .bss : 0xc066dd98 - 0xc073a680 ( 819 kB)
  103. [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  104. [ 0.000000] NR_IRQS:114
  105. [ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
  106. [ 0.000000] Console: colour dummy device 80x30
  107. [ 15.723259] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
  108. [ 15.813156] pid_max: default: 32768 minimum: 301
  109. [ 15.813265] Security Framework initialized
  110. [ 15.813287] AppArmor: AppArmor disabled by boot time parameter
  111. [ 15.813345] Mount-cache hash table entries: 512
  112. [ 15.813850] Initializing cgroup subsys cpuacct
  113. [ 15.813867] Initializing cgroup subsys devices
  114. [ 15.813879] Initializing cgroup subsys freezer
  115. [ 15.813888] Initializing cgroup subsys net_cls
  116. [ 15.813896] Initializing cgroup subsys blkio
  117. [ 15.813903] Initializing cgroup subsys perf_event
  118. [ 15.813920] Initializing cgroup subsys bfqio
  119. [ 15.814008] CPU: Testing write buffer coherency: ok
  120. [ 15.814325] Setting up static identity map for 0x468c10 - 0x468c4c
  121. [ 15.815630] devtmpfs: initialized
  122. [ 15.817546] pinctrl core: initialized pinctrl subsystem
  123. [ 15.817833] NET: Registered protocol family 16
  124. [ 15.818865] DMA: preallocated 1024 KiB pool for atomic coherent allocations
  125. [ 15.819529] Kirkwood: MV88F6281-A1, TCLK=200000000.
  126. [ 15.819546] Feroceon L2: Enabling L2
  127. [ 15.819580] Feroceon L2: Cache support initialised.
  128. [ 15.819952] initial MPP regs: 21111111 01003311 33331100 33003333 00000533 20202000 00000000
  129. [ 15.819984] final MPP regs: 01111111 00003311 00001100 00000000 00000000 00000000 00000000
  130. [ 15.825069] bio: create slab <bio-0> at 0
  131. [ 15.825430] vgaarb: loaded
  132. [ 15.825675] SCSI subsystem initialized
  133. [ 15.825821] libata version 3.00 loaded.
  134. [ 15.826020] usbcore: registered new interface driver usbfs
  135. [ 15.826080] usbcore: registered new interface driver hub
  136. [ 15.826174] usbcore: registered new device driver usb
  137. [ 15.826277] pps_core: LinuxPPS API ver. 1 registered
  138. [ 15.826286] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
  139. [ 15.826309] PTP clock support registered
  140. [ 15.826940] Switching to clocksource orion_clocksource
  141. [ 15.838882] FS-Cache: Loaded
  142. [ 15.847970] NET: Registered protocol family 2
  143. [ 15.848455] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
  144. [ 15.848511] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
  145. [ 15.848542] TCP: Hash tables configured (established 2048 bind 2048)
  146. [ 15.848599] TCP: reno registered
  147. [ 15.848612] UDP hash table entries: 256 (order: 0, 4096 bytes)
  148. [ 15.848634] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  149. [ 15.848836] NET: Registered protocol family 1
  150. [ 15.848871] PCI: CLS 0 bytes, default 32
  151. [ 15.849784] audit: initializing netlink socket (disabled)
  152. [ 15.849820] type=2000 audit(0.120:1): initialized
  153. [ 15.938630] VFS: Disk quotas dquot_6.5.2
  154. [ 15.938824] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  155. [ 15.940917] jffs2: version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
  156. [ 15.941781] aufs 3.8-20130311
  157. [ 15.941803] msgmni has been set to 493
  158. [ 15.943267] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
  159. [ 15.943279] io scheduler noop registered
  160. [ 15.943286] io scheduler deadline registered
  161. [ 15.943443] io scheduler cfq registered
  162. [ 15.943482] io scheduler bfq registered (default)
  163. [ 15.943591] mv_xor mv_xor.0: Marvell XOR driver
  164. [ 15.977024] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
  165. [ 16.017016] mv_xor mv_xor.0: Marvell XOR: ( xor fill cpy )
  166. [ 16.017144] mv_xor mv_xor.1: Marvell XOR driver
  167. [ 16.057016] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
  168. [ 16.097016] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
  169. [ 16.101023] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
  170. [ 16.121694] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
  171. [ 16.671673] console [ttyS0] enabled
  172. [ 16.681176] brd: module loaded
  173. [ 16.687223] loop: module loaded
  174. [ 16.690592] sata_mv sata_mv.0: version 1.28
  175. [ 16.694849] sata_mv sata_mv.0: cannot get optional clkdev
  176. [ 16.700380] sata_mv sata_mv.0: slots 32 ports 2
  177. [ 16.707537] scsi0 : sata_mv
  178. [ 16.710678] scsi1 : sata_mv
  179. [ 16.713695] ata1: SATA max UDMA/133 irq 21
  180. [ 16.717839] ata2: SATA max UDMA/133 irq 21
  181. [ 16.722708] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
  182. [ 16.734982] Scanning device for bad blocks
  183. [ 16.811883] Bad eraseblock 693 at 0x0000056a0000
  184. [ 16.840183] Bad eraseblock 919 at 0x0000072e0000
  185. [ 16.847821] Bad eraseblock 948 at 0x000007680000
  186. [ 16.860669] Creating 9 MTD partitions on "orion_nand":
  187. [ 16.865834] 0x000000000000-0x000000100000 : "uboot"
  188. [ 16.871086] 0x000000100000-0x000000180000 : "uboot_env"
  189. [ 16.876605] 0x000000180000-0x000000200000 : "key_store"
  190. [ 16.882129] 0x000000200000-0x000000280000 : "info"
  191. [ 16.887212] 0x000000280000-0x000000c80000 : "etc"
  192. [ 16.892201] 0x000000c80000-0x000001680000 : "kernel_1"
  193. [ 16.897648] 0x000001680000-0x000004640000 : "rootfs1"
  194. [ 16.903049] 0x000004640000-0x000005040000 : "kernel_2"
  195. [ 16.908498] 0x000005040000-0x000008000000 : "rootfs2"
  196. [ 16.914295] pch_gbe: EG20T PCH Gigabit Ethernet Driver - version 1.01
  197. [ 16.920894] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  198. [ 16.927521] orion-ehci orion-ehci.0: Marvell Orion EHCI
  199. [ 16.932790] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
  200. [ 16.940533] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
  201. [ 16.957006] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
  202. [ 16.963499] hub 1-0:1.0: USB hub found
  203. [ 16.967306] hub 1-0:1.0: 1 port detected
  204. [ 16.971531] ehci-pci: EHCI PCI platform driver
  205. [ 16.976098] Initializing USB Mass Storage driver...
  206. [ 16.981119] usbcore: registered new interface driver usb-storage
  207. [ 16.987164] USB Mass Storage support registered.
  208. [ 16.992116] mousedev: PS/2 mouse device common for all mice
  209. [ 16.998006] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
  210. [ 17.004273] orion_wdt: Initial timeout 21 sec
  211. [ 17.008773] cpuidle: using governor ladder
  212. [ 17.012971] cpuidle: using governor menu
  213. [ 17.017024] sdhci: Secure Digital Host Controller Interface driver
  214. [ 17.023230] sdhci: Copyright(c) Pierre Ossman
  215. [ 17.027667] sdhci-pltfm: SDHCI platform and OF driver helper
  216. [ 17.033384] leds-gpio leds-gpio: pins are not configured from the driver
  217. [ 17.040154] orion_gpio_is_valid: invalid GPIO 12
  218. [ 17.045823] usbcore: registered new interface driver r8712u
  219. [ 17.051788] gre: GRE over IPv4 demultiplexor driver
  220. [ 17.056805] TCP: cubic registered
  221. [ 17.060178] NET: Registered protocol family 17
  222. [ 17.064741] Key type dns_resolver registered
  223. [ 17.069695] registered taskstats version 1
  224. [ 17.074781] console [netcon0] enabled
  225. [ 17.078559] netconsole: network logging started
  226. [ 17.083405] input: gpio-keys as /devices/platform/gpio-keys/input/input0
  227. [ 17.090411] rtc-mv rtc-mv: setting system clock to 2013-05-08 15:25:12 UTC (1368026712)
  228. [ 17.236995] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
  229. [ 17.286991] usb 1-1: new high-speed USB device number 2 using orion-ehci
  230. [ 17.317026] ata1.00: ATA-8: ST9250315AS, 0001SDM1, max UDMA/133
  231. [ 17.322977] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
  232. [ 17.387029] ata1.00: configured for UDMA/133
  233. [ 17.407317] scsi 0:0:0:0: Direct-Access ATA ST9250315AS 0001 PQ: 0 ANSI: 5
  234. [ 17.415952] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
  235. [ 17.423728] sd 0:0:0:0: [sda] Write Protect is off
  236. [ 17.428987] sd 0:0:0:0: Attached scsi generic sg0 type 0
  237. [ 17.434394] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
  238. [ 17.440003] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
  239. [ 17.449790] hub 1-1:1.0: USB hub found
  240. [ 17.454283] hub 1-1:1.0: 4 ports detected
  241. [ 17.458708] sda: sda1 sda2
  242. [ 17.462935] sd 0:0:0:0: [sda] Attached SCSI disk
  243. [ 17.747297] usb 1-1.2: new high-speed USB device number 3 using orion-ehci
  244. [ 17.786987] ata2: SATA link down (SStatus 0 SControl F300)
  245. [ 17.862635] scsi2 : usb-storage 1-1.2:1.0
  246. [ 17.897586] EXT3-fs (sda2): error: couldn't mount because of unsupported optional features (240)
  247. [ 17.919626] EXT2-fs (sda2): error: couldn't mount because of unsupported optional features (240)
  248. [ 18.089437] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
  249. [ 18.097186] VFS: Mounted root (ext4 filesystem) on device 8:2.
  250. [ 18.134650] devtmpfs: mounted
  251. [ 18.138171] Freeing init memory: 176K
  252. [ 18.858388] scsi 2:0:0:0: Direct-Access TOSHIBA TransMemory PMAP PQ: 0 ANSI: 0 CCS
  253. [ 18.868720] sd 2:0:0:0: Attached scsi generic sg1 type 0
  254. [ 18.874590] sd 2:0:0:0: [sdb] 15622144 512-byte logical blocks: (7.99 GB/7.44 GiB)
  255. [ 18.884576] sd 2:0:0:0: [sdb] Write Protect is off
  256. [ 18.889626] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
  257. [ 18.895455] sd 2:0:0:0: [sdb] No Caching mode page present
  258. [ 18.901000] sd 2:0:0:0: [sdb] Assuming drive cache: write through
  259. [ 18.910816] sd 2:0:0:0: [sdb] No Caching mode page present
  260. [ 18.916342] sd 2:0:0:0: [sdb] Assuming drive cache: write through
  261. [ 18.924943] sdb: sdb1 sdb2
  262. [ 18.930443] sd 2:0:0:0: [sdb] No Caching mode page present
  263. [ 18.935959] sd 2:0:0:0: [sdb] Assuming drive cache: write through
  264. [ 18.942113] sd 2:0:0:0: [sdb] Attached SCSI removable disk
  265. [ 19.066809] systemd[1]: systemd 197 running in system mode. (+PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
  266.  
  267. Welcome to Arch Linux ARM!
  268.  
  269. [ 19.255564] systemd[1]: Inserted module 'autofs4'
  270. [ 19.289333] systemd[1]: Set hostname to <alarm>.
  271. [ 19.588876] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory. See system logs a
  272. nd 'systemctl status display-manager.service' for details.
  273. [ 19.611088] systemd[1]: Expecting device dev-ttyS0.device...
  274. Expecting device dev-ttyS0.device...
  275. [ 19.637113] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
  276. [ 19.645200] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
  277. [ 19.652933] systemd[1]: Starting Syslog Socket.
  278. [ OK ] Listening on Syslog Socket.
  279. [ 19.677073] systemd[1]: Listening on Syslog Socket.
  280. [ 19.682058] systemd[1]: Starting Remote File Systems.
  281. [ OK ] Reached target Remote File Systems.
  282. [ 19.707074] systemd[1]: Reached target Remote File Systems.
  283. [ 19.712765] systemd[1]: Starting Device-mapper event daemon FIFOs.
  284. [ OK ] Listening on Device-mapper event daemon FIFOs.
  285. [ 19.737073] systemd[1]: Listening on Device-mapper event daemon FIFOs.
  286. [ 19.743704] systemd[1]: Starting Delayed Shutdown Socket.
  287. [ OK ] Listening on Delayed Shutdown Socket.
  288. [ 19.767075] systemd[1]: Listening on Delayed Shutdown Socket.
  289. [ 19.772923] systemd[1]: Starting LVM2 metadata daemon socket.
  290. [ OK ] Listening on LVM2 metadata daemon socket.
  291. [ 19.797067] systemd[1]: Listening on LVM2 metadata daemon socket.
  292. [ 19.803260] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
  293. [ OK ] Listening on /dev/initctl Compatibility Named Pipe.
  294. [ 19.827077] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
  295. [ 19.834252] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
  296. [ OK ] Set up automount Arbitrary Executable File Formats F...utomount Point.
  297. [ 19.867086] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
  298. [ 19.876603] systemd[1]: Starting Encrypted Volumes.
  299. [ OK ] Reached target Encrypted Volumes.
  300. [ 19.897073] systemd[1]: Reached target Encrypted Volumes.
  301. [ 19.902592] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
  302. [ 19.910883] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
  303. [ 19.919259] systemd[1]: Starting udev Kernel Socket.
  304. [ OK ] Listening on udev Kernel Socket.
  305. [ 19.947080] systemd[1]: Listening on udev Kernel Socket.
  306. [ 19.952771] systemd[1]: Starting udev Control Socket.
  307. [ OK ] Listening on udev Control Socket.
  308. [ 19.977069] systemd[1]: Listening on udev Control Socket.
  309. [ 19.982565] systemd[1]: Starting Swap.
  310. [ OK ] Reached target Swap.
  311. [ 20.007071] systemd[1]: Reached target Swap.
  312. [ 20.011451] systemd[1]: Starting Journal Socket.
  313. [ OK ] Listening on Journal Socket.
  314. [ 20.037074] systemd[1]: Listening on Journal Socket.
  315. [ 20.042156] systemd[1]: Mounting Temporary Directory...
  316. Mounting Temporary Directory...
  317. [ 20.100708] systemd[1]: Starting udev Coldplug all Devices...
  318. Starting udev Coldplug all Devices...
  319. [ 20.355238] systemd[1]: Started Load Kernel Modules.
  320. [ 20.361804] systemd[1]: Started Set Up Additional Binary Formats.
  321. [ 20.368054] systemd[1]: Mounted Configuration File System.
  322. [ 20.383649] systemd[1]: Starting Apply Kernel Variables...
  323. Starting Apply Kernel Variables...
  324. [ 20.409356] systemd[1]: Mounted Huge Pages File System.
  325. [ 20.417034] systemd[1]: Mounting POSIX Message Queue File System...
  326. Mounting POSIX Message Queue File System...
  327. [ 20.450786] systemd[1]: Starting udev Kernel Device Manager...
  328. Starting udev Kernel Device Manager...
  329. [ 20.489461] systemd[1]: Mounting Debug File System...
  330. Mounting Debug File System...
  331. [ 20.522442] systemd[1]: Starting Setup Virtual Console...
  332. Starting Setup Virtual Console...
  333. [ 20.559359] systemd[1]: Mounted FUSE Control File System.
  334. [ 20.567504] systemd[1]: Starting Journal Service...
  335. Starting Journal Service...
  336. [ 20.579821] systemd-udevd[56]: starting version 197
  337. [ OK ] Started Journal Service.
  338. [ 20.607165] systemd[1]: Started Journal Service.
  339. [ 20.611982] systemd[1]: Starting Syslog.
  340. [ OK ] Reached target Syslog.
  341. [ 20.637166] systemd[1]: Reached target Syslog.
  342. [ 20.641801] systemd[1]: Started File System Check on Root Device.
  343. [ 20.648098] systemd[1]: Starting Remount Root and Kernel File Systems...
  344. Starting Remount Root and Kernel File Systems...
  345. [ OK ] Started udev Kernel Device Manager.
  346. [ 20.697150] systemd[1]: Started udev Kernel Device Manager.
  347. [ OK ] Mounted Temporary Directory.
  348. [ 20.728309] systemd[1]: Mounted Temporary Directory.
  349. [ OK ] Started Apply Kernel Variables.
  350. [ 20.767179] systemd[1]: Started Apply Kernel Variables.
  351. [ OK ] Mounted POSIX Message Queue File System.
  352. [ 20.787202] systemd[1]: Mounted POSIX Message Queue File System.
  353. [ OK ] Mounted Debug File System.
  354. [ 20.807226] systemd[1]: Mounted Debug File System.
  355. [ OK ] Started Remount Root and Kernel File Systems.
  356. [ 20.847128] systemd[1]: Started Remount Root and Kernel File Systems.
  357. [ OK ] Started udev Coldplug all Devices.
  358. [ 20.877099] systemd[1]: Started udev Coldplug all Devices.
  359. [ 20.882950] systemd[1]: Starting Local File Systems (Pre).
  360. [ OK ] Reached target Local File Systems (Pre).
  361. [ 20.907147] systemd[1]: Reached target Local File Systems (Pre).
  362. [ 20.913295] systemd[1]: Starting Load Random Seed...
  363. Starting Load Random Seed...
  364. [ 20.939377] systemd[1]: Starting Local File Systems.
  365. [ OK ] Reached target Local File Systems.
  366. [ 20.967100] systemd[1]: Reached target Local File Systems.
  367. [ 21.224256] systemd[1]: Starting Recreate Volatile Files and Directories...
  368. Starting Recreate Volatile Files and Directories...
  369. [ 21.249439] systemd[1]: Starting Trigger Flushing of Journal to Persistent Storage...
  370. Starting Trigger Flushing of Journal to Persistent Storage...
  371. [ OK ] Started Load Random Seed.
  372. [ 21.932587] systemd-journald[62]: Received SIGUSR1
  373. [ OK ] Started Recreate Volatile Files and Directories.
  374. [ OK ] Started Setup Virtual Console.
  375. [ OK ] Reached target System Initialization.
  376. [ OK ] Listening on D-Bus System Message Bus Socket.
  377. [ OK ] Reached target Sockets.
  378. [ OK ] Reached target Basic System.
  379. Starting Periodic Command Scheduler...
  380. [ 22.237515] systemd-journald[62]: File /var/log/journal/5c49cb5bf08724338eb09a6900092bb0/system.journal corrupted or uncleanly shut down, renaming and replacing.
  381. [ OK ] Started Periodic Command Scheduler.
  382. Starting Netcfg multi-profile daemon...
  383. Starting OpenSSH Daemon...
  384. [ OK ] Started OpenSSH Daemon.
  385. Starting Login Service...
  386. Starting D-Bus System Message Bus...
  387. [ OK ] Started D-Bus System Message Bus.
  388. Starting System Logger Daemon...
  389. [ 22.576757] nsa3xx-hwmon nsa3xx-hwmon: initialized
  390. [ OK ] Started System Logger Daemon.
  391. [ OK ] Started Trigger Flushing of Journal to Persistent Storage.
  392. Starting Permit User Sessions...
  393. [ OK ] Found device /dev/ttyS0.
  394. [ 24.282228] NET: Registered protocol family 10
  395. [ OK ] Started Permit User Sessions.
  396. Starting Getty on tty1...
  397. [ OK ] Started Getty on tty1.
  398. Starting Serial Getty on ttyS0...
  399. [ OK ] Started Serial Getty on ttyS0.
  400. [ OK ] Reached target Login Prompts.
  401. [ OK ] Started Login Service.
  402. [FAILED] Failed to start Netcfg multi-profile daemon.
  403. See 'systemctl status netcfg.service' for details.
  404. [ OK ] Reached target Network.
  405. Starting OpenNTP Daemon...
  406.  
  407. Arch Linux 3.8.11-2-ARCH (ttyS0)
  408.  
  409. alarm login: root
  410. Password:
  411. Last login: Wed May 8 10:18:29 on ttyS0
  412. [root@alarm ~]# i[ OK ] Started OpenNTP Daemon.
  413. [ OK ] Reached target Multi-User.
  414. [ OK ] Reached target Graphical Interface.
  415. fconfig
  416. lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
  417. inet 127.0.0.1 netmask 255.0.0.0
  418. inet6 ::1 prefixlen 128 scopeid 0x10<host>
  419. loop txqueuelen 0 (Local Loopback)
  420. RX packets 36 bytes 2564 (2.5 KiB)
  421. RX errors 0 dropped 0 overruns 0 frame 0
  422. TX packets 36 bytes 2564 (2.5 KiB)
  423. TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
  424.  
  425. [root@alarm ~]# ls /sys/class/net
  426. lo
  427. [root@alarm ~]# lsmod
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!