Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.5.13-arch1-1] (local build)
- Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.5.13-arch1-1] (local build)
- Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Device Model: WDC WD10SDRW-11A0XS0
- Serial Number: WD-WXG1A5934UJ6
- LU WWN Device Id: 5 0014ee 2bc034069
- Firmware Version: 01.01A01
- User Capacity: 1,000,171,331,584 bytes [1.00 TB]
- Sector Sizes: 512 bytes logical, 4096 bytes physical
- Rotation Rate: 5400 rpm
- Form Factor: 2.5 inches
- Device is: Not in smartctl database [for details use: -P showall]
- ATA Version is: ACS-3 T13/2161-D revision 5
- SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
- Local Time is: Mon Mar 30 22:39:51 2020 CDT
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x00) Offline data collection activity
- was never started.
- Auto Offline Data Collection: Disabled.
- Self-test execution status: ( 40) The self-test routine was interrupted
- by the host with a hard or soft reset.
- Total time to complete Offline
- data collection: ( 8700) seconds.
- Offline data collection
- capabilities: (0x51) SMART execute Offline immediate.
- No Auto Offline data collection support.
- Suspend Offline collection upon new
- command.
- No Offline surface scan supported.
- Self-test supported.
- No Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 2) minutes.
- Extended self-test routine
- recommended polling time: ( 156) minutes.
- SCT capabilities: (0x7035) SCT Status supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
- 1 Raw_Read_Error_Rate 0x002f 195 195 051 Pre-fail Always - 232
- 3 Spin_Up_Time 0x0027 170 160 021 Pre-fail Always - 2500
- 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 69
- 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
- 7 Seek_Error_Rate 0x002e 080 001 000 Old_age Always - 65535
- 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 157
- 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
- 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
- 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 55
- 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 40
- 193 Load_Cycle_Count 0x0032 199 199 000 Old_age Always - 4628
- 194 Temperature_Celsius 0x0022 118 085 000 Old_age Always - 25
- 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
- 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 50
- 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
- 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
- 200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
- SMART Error Log Version: 1
- ATA Error Count: 3
- CR = Command Register [HEX]
- FR = Features Register [HEX]
- SC = Sector Count Register [HEX]
- SN = Sector Number Register [HEX]
- CL = Cylinder Low Register [HEX]
- CH = Cylinder High Register [HEX]
- DH = Device/Head Register [HEX]
- DC = Device Command Register [HEX]
- ER = Error register [HEX]
- ST = Status register [HEX]
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 3 occurred at disk power-on lifetime: 102 hours (4 days + 6 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 04 61 00 00 00 00 00 Device Fault; Error: ABRT
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- ef 02 00 00 00 00 00 00 00:44:09.564 SET FEATURES [Enable write cache]
- ef 90 06 00 00 00 00 00 00:44:09.563 SET FEATURES [Disable SATA feature]
- e1 00 02 00 00 00 00 00 00:44:09.563 IDLE IMMEDIATE
- ec 00 01 00 00 00 00 00 00:44:09.563 IDENTIFY DEVICE
- Error 2 occurred at disk power-on lifetime: 102 hours (4 days + 6 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 04 61 06 00 00 00 00 Device Fault; Error: ABRT
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- ef 90 06 00 00 00 00 00 00:44:09.563 SET FEATURES [Disable SATA feature]
- e1 00 02 00 00 00 00 00 00:44:09.563 IDLE IMMEDIATE
- ec 00 01 00 00 00 00 00 00:44:09.563 IDENTIFY DEVICE
- Error 1 occurred at disk power-on lifetime: 102 hours (4 days + 6 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 04 61 02 00 00 00 00
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- e1 00 02 00 00 00 00 00 00:44:09.563 IDLE IMMEDIATE
- ec 00 01 00 00 00 00 00 00:44:09.563 IDENTIFY DEVICE
- SMART Self-test log structure revision number 1
- Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
- # 1 Extended offline Interrupted (host reset) 80% 157 -
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement