[    0.000000] Linux version 4.19.78 (builder@buildhost) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r11175-700e7a2eb9)) #0 Tue Oct 8 19:51:08 2019
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] MIPS: machine is D-Link DIR-842 C3
[    0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] On node 0 totalpages: 32768
[    0.000000]   Normal zone: 288 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] random: get_random_bytes called from start_kernel+0x98/0x4b0 with crng_init=0
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 122160K/131072K available (4507K kernel code, 181K rwdata, 1052K rodata, 1228K init, 214K bss, 8912K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] CPU clock: 775.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[    0.000007] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[    0.008218] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.074761] pid_max: default: 32768 minimum: 301
[    0.079819] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.086798] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.098462] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.108867] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.115428] pinctrl core: initialized pinctrl subsystem
[    0.123284] NET: Registered protocol family 16
[    0.134857] PCI host bridge /ahb/pcie-controller@18250000 ranges:
[    0.141350]  MEM 0x0000000012000000..0x0000000013ffffff
[    0.146851]   IO 0x0000000000000000..0x0000000000000000
[    0.170102] PCI host bridge to bus 0000:00
[    0.174487] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[    0.181729] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.187608] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.194759] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.203142] pci 0000:00:00.0: [168c:0056] type 00 class 0x028000
[    0.203199] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.203322] pci 0000:00:00.0: PME# supported from D0 D3hot
[    0.204271] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.204297] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[    0.215306] clocksource: Switched to clocksource MIPS
[    0.221662] NET: Registered protocol family 2
[    0.227125] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes)
[    0.235222] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.242624] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.249338] TCP: Hash tables configured (established 1024 bind 1024)
[    0.256166] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.262330] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.269288] NET: Registered protocol family 1
[    0.273924] PCI: CLS 0 bytes, default 32
[    0.276808] Crashlog allocated RAM at address 0x3f00000
[    0.283638] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.296446] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.302591] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.325095] io scheduler noop registered
[    0.329279] io scheduler deadline registered (default)
[    0.336906] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[    0.343926] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.352776] console [ttyS0] disabled
[    0.356616] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A
[    0.365720] console [ttyS0] enabled
[    0.373258] bootconsole [early0] disabled
[    0.400546] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.405486] 8 fixed-partitions partitions found on MTD device spi0.0
[    0.412047] Creating 8 MTD partitions on "spi0.0":
[    0.417035] 0x000000000000-0x000000040000 : "u-boot"
[    0.422939] 0x000000040000-0x000000050000 : "u-boot-env"
[    0.429173] 0x000000050000-0x000000060000 : "devdata"
[    0.435082] 0x000000060000-0x000000070000 : "devconf"
[    0.441057] 0x000000070000-0x000000080000 : "misc"
[    0.446791] 0x000000080000-0x000000fd0000 : "firmware"
[    0.457075] 2 seama-fw partitions found on MTD device firmware
[    0.463104] Creating 2 MTD partitions on "firmware":
[    0.468290] 0x000000000040-0x0000001d0000 : "kernel"
[    0.474134] 0x0000001d0000-0x000000f50000 : "rootfs"
[    0.479983] mtd: device 7 (rootfs) set to be root filesystem
[    0.487313] 1 squashfs-split partitions found on MTD device rootfs
[    0.493724] 0x000000460000-0x000000f50000 : "rootfs_data"
[    0.500110] 0x000000fd0000-0x000000fe0000 : "art"
[    0.505737] 0x000000fe0000-0x000001000000 : "reserved"
[    0.512732] libphy: Fixed MDIO Bus: probed
[    0.519995] ag71xx 19000000.eth: invalid MAC address, using random address
[    1.205686] libphy: ag71xx_mdio: probed
[    1.212692] switch0: Atheros AR8337 rev. 2 switch registered on mdio-bus.0
[    1.866780] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[    1.878445] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
[    1.887243] NET: Registered protocol family 10
[    1.897177] Segment Routing with IPv6
[    1.901060] NET: Registered protocol family 17
[    1.905782] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.919181] 8021q: 802.1Q VLAN Support v1.8
[    1.925100] hctosys: unable to open rtc device (rtc0)
[    1.937921] VFS: Mounted root (squashfs filesystem) readonly on device 31:7.
[    1.952079] Freeing unused kernel memory: 1228K
[    1.956789] This architecture does not have kernel memory protection.
[    1.963436] Run /sbin/init as init process
[    2.545332] random: fast init done
[    2.808412] init: Console is alive
[    2.812135] init: - watchdog -
[    4.211712] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.360005] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.377910] init: - preinit -
[    5.284647] random: jshn: uninitialized urandom read (4 bytes read)
[    5.396997] random: jshn: uninitialized urandom read (4 bytes read)
[    5.816870] random: jshn: uninitialized urandom read (4 bytes read)
[    7.121315] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    7.127475] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[    7.165655] urandom_read: 4 callbacks suppressed
[    7.165662] random: procd: uninitialized urandom read (4 bytes read)
[    8.186623] eth0: link up (1000Mbps/Full duplex)
[    8.191479] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    8.198326] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   10.463171] jffs2: notice: (537) jffs2_build_xattr_subsystem: complete building xattr subsystem, 10 of xdatum (2 unchecked, 8 orphan) and 23 of xref (8 dead, 0 orphan) found.
[   10.486932] mount_root: switching to jffs2 overlay
[   10.516261] overlayfs: upper fs does not support tmpfile.
[   10.528409] urandom-seed: Seeding with /etc/urandom.seed
[   10.628118] eth0: link down
[   10.648707] procd: - early -
[   10.651770] procd: - watchdog -
[   11.284168] procd: - watchdog -
[   11.287730] procd: - ubus -
[   11.312113] random: ubusd: uninitialized urandom read (4 bytes read)
[   11.341337] random: ubusd: uninitialized urandom read (4 bytes read)
[   11.349258] procd: - init -
[   11.999864] kmodloader: loading kernel modules from /etc/modules.d/*
[   12.064313] Loading modules backported from Linux version v5.3-rc4-0-gd45331b00ddb
[   12.072184] Backport generated by backports.git v5.3-rc4-1-0-g4ec72687
[   12.139900] xt_time: kernel timezone is -0000
[   12.153347] urngd: v1.0.0 started.
[   12.307548] PPP generic driver version 2.4.2
[   12.326421] NET: Registered protocol family 24
[   12.398721] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x56.
[   12.422332] random: crng init done
[   12.426879] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[   12.433673] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[   12.809544] firmware ath10k!fwcfg-pci-0000:00:00.0.txt: firmware_loading_store: map pages failed
[   13.001701] firmware ath10k!QCA9888!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[   13.196200] firmware ath10k!QCA9888!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[   13.386691] firmware ath10k!QCA9888!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[   14.192395] ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
[   14.201963] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   14.221991] ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9888-fW-012-54863dff api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 31e46a3c
[   14.557856] ath10k_pci 0000:00:00.0: board_file api 2 bmi_id 0:18 crc32 f228337a
[   16.607223] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   16.614961] ath10k_pci 0000:00:00.0: msdu-desc: 2500  skid: 32
[   16.645243] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   16.656614] ath10k_pci 0000:00:00.0: wmi print 'free: 117872 iram: 22788 sram: 26020'
[   16.867342] ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[   16.978198] ath: EEPROM regdomain: 0x0
[   16.978205] ath: EEPROM indicates default country code should be used
[   16.978208] ath: doing EEPROM country->regdmn map search
[   16.978221] ath: country maps to regdmn code: 0x3a
[   16.978226] ath: Country alpha2 being used: US
[   16.978229] ath: Regpair used: 0x3a
[   17.062093] ath: EEPROM regdomain: 0x0
[   17.062100] ath: EEPROM indicates default country code should be used
[   17.062103] ath: doing EEPROM country->regdmn map search
[   17.062115] ath: country maps to regdmn code: 0x3a
[   17.062119] ath: Country alpha2 being used: US
[   17.062122] ath: Regpair used: 0x3a
[   17.074044] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[   17.075545] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=2
[   17.167387] kmodloader: done loading kernel modules from /etc/modules.d/*
[   25.049757] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   25.068822] device eth0 entered promiscuous mode
[   25.080374] br-lan: port 1(eth0.1) entered blocking state
[   25.086009] br-lan: port 1(eth0.1) entered disabled state
[   25.091877] device eth0.1 entered promiscuous mode
[   25.131207] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   25.181972] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   26.107089] eth0: link up (1000Mbps/Full duplex)
[   26.111942] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   26.269608] br-lan: port 1(eth0.1) entered blocking state
[   26.275191] br-lan: port 1(eth0.1) entered forwarding state
[   26.281262] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   26.405574] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   29.881514] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   29.889294] ath10k_pci 0000:00:00.0: msdu-desc: 2500  skid: 32
[   29.919756] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   29.931077] ath10k_pci 0000:00:00.0: wmi print 'free: 117872 iram: 22788 sram: 26020'
[   30.221727] ath10k_pci 0000:00:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[   30.233309] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   30.890551] ath10k_pci 0000:00:00.0: NOTE:  Firmware DBGLOG output disabled in debug_mask: 0x10000000
[   30.924780] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   30.934395] br-lan: port 2(wlan1) entered blocking state
[   30.940023] br-lan: port 2(wlan1) entered disabled state
[   30.945891] device wlan1 entered promiscuous mode
[   30.950940] br-lan: port 2(wlan1) entered blocking state
[   30.956476] br-lan: port 2(wlan1) entered forwarding state
[   31.255417] br-lan: port 2(wlan1) entered disabled state
[   31.397019] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   31.403785] br-lan: port 2(wlan1) entered blocking state
[   31.409331] br-lan: port 2(wlan1) entered forwarding state
[   42.168972] wlan0: authenticate with 1a:5b:0e:2e:19:00
[   42.396252] wlan0: send auth to 1a:5b:0e:2e:19:00 (try 1/3)
[   42.406315] wlan0: authenticated
[   42.415481] wlan0: associate with 1a:5b:0e:2e:19:00 (try 1/3)
[   42.430400] ath10k_pci 0000:00:00.0: Invalid peer id 0 or peer stats buffer, peer:   (null)  sta:   (null)
[   42.440768] wlan0: RX AssocResp from 1a:5b:0e:2e:19:00 (capab=0x401 status=0 aid=1)
[   42.454406] wlan0: associated
[   42.462954] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 1849.532671] device wlan1 left promiscuous mode
[ 1849.537449] br-lan: port 2(wlan1) entered disabled state
[ 1850.287190] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 1850.330496] br-lan: port 2(wlan1) entered blocking state
[ 1850.336082] br-lan: port 2(wlan1) entered disabled state
[ 1850.341894] device wlan1 entered promiscuous mode
[ 1850.346898] br-lan: port 2(wlan1) entered blocking state
[ 1850.352403] br-lan: port 2(wlan1) entered forwarding state
[ 1850.692527] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 2322.209717] wlan0: AP 1a:5b:0e:2e:19:00 changed bandwidth, new config is 5180 MHz, width 2 (5190/0 MHz)
[ 3057.191468] wlan0: deauthenticating from 1a:5b:0e:2e:19:00 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 3057.201416] ath10k_pci 0000:00:00.0: peer-unmap-event: unknown peer id 1
[ 3060.251234] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[ 3060.258989] ath10k_pci 0000:00:00.0: msdu-desc: 2500  skid: 32
[ 3060.289396] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[ 3060.300803] ath10k_pci 0000:00:00.0: wmi print 'free: 117872 iram: 22788 sram: 26020'
[ 3060.593420] ath10k_pci 0000:00:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 3060.605138] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3067.930712] wlan0: authenticate with 1a:5b:0e:2e:19:00
[ 3068.155974] wlan0: send auth to 1a:5b:0e:2e:19:00 (try 1/3)
[ 3068.163370] wlan0: authenticated
[ 3068.170308] wlan0: associate with 1a:5b:0e:2e:19:00 (try 1/3)
[ 3068.193986] wlan0: associate with 1a:5b:0e:2e:19:00 (try 2/3)
[ 3068.212820] wlan0: associate with 1a:5b:0e:2e:19:00 (try 3/3)
[ 3068.229304] wlan0: association with 1a:5b:0e:2e:19:00 timed out
[ 3068.235670] ath10k_pci 0000:00:00.0: peer-unmap-event: unknown peer id 1
[ 3072.433651] wlan0: authenticate with 1a:5b:0e:2e:19:00
[ 3072.446664] wlan0: send auth to 1a:5b:0e:2e:19:00 (try 1/3)
[ 3072.457078] wlan0: authenticated
[ 3072.481147] wlan0: associate with 1a:5b:0e:2e:19:00 (try 1/3)
[ 3072.492013] wlan0: RX AssocResp from 1a:5b:0e:2e:19:00 (capab=0x401 status=0 aid=1)
[ 3072.510935] wlan0: associated
[ 3072.518915] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 3440.313374] ath10k_pci 0000:00:00.0: peer-unmap-event: unknown peer id 1
[ 3479.093765] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[ 3479.101597] ath10k_pci 0000:00:00.0: msdu-desc: 2500  skid: 32
[ 3479.131903] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[ 3479.143312] ath10k_pci 0000:00:00.0: wmi print 'free: 117872 iram: 22788 sram: 26020'
[ 3479.438517] ath10k_pci 0000:00:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 3479.450129] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3567.308469] wlan0: authenticate with 1a:5b:0e:2e:19:00
[ 3567.534075] wlan0: send auth to 1a:5b:0e:2e:19:00 (try 1/3)
[ 3567.541610] wlan0: authenticated
[ 3567.550324] wlan0: associate with 1a:5b:0e:2e:19:00 (try 1/3)
[ 3567.563893] wlan0: RX AssocResp from 1a:5b:0e:2e:19:00 (capab=0x401 status=0 aid=2)
[ 3567.573347] wlan0: associated
[ 3567.582112] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 4122.085603] wlan0: AP 1a:5b:0e:2e:19:00 changed bandwidth, new config is 5220 MHz, width 2 (5230/0 MHz)
[ 5509.730832] wlan0: deauthenticated from 1a:5b:0e:2e:19:00 (Reason: 6=CLASS2_FRAME_FROM_NONAUTH_STA)
[ 5509.740856] ath10k_pci 0000:00:00.0: peer-unmap-event: unknown peer id 1
[ 5509.814310] wlan0: authenticate with 1a:5b:0e:2e:19:00
[ 5510.038152] wlan0: send auth to 1a:5b:0e:2e:19:00 (try 1/3)
[ 5510.052394] wlan0: authenticated
[ 5510.065908] wlan0: associate with 1a:5b:0e:2e:19:00 (try 1/3)
[ 5510.185781] wlan0: associate with 1a:5b:0e:2e:19:00 (try 2/3)
[ 5510.194649] wlan0: RX AssocResp from 1a:5b:0e:2e:19:00 (capab=0x401 status=0 aid=1)
[ 5510.204236] wlan0: associated
[ 5562.607383] wlan0: deauthenticating from 1a:5b:0e:2e:19:00 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 5562.617394] ath10k_pci 0000:00:00.0: peer-unmap-event: unknown peer id 1
[ 5565.676853] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[ 5565.684596] ath10k_pci 0000:00:00.0: msdu-desc: 2500  skid: 32
[ 5565.715050] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[ 5565.726455] ath10k_pci 0000:00:00.0: wmi print 'free: 117872 iram: 22788 sram: 26020'
[ 5566.016505] ath10k_pci 0000:00:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 5566.028091] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 5569.336928] wlan0: authenticate with 1a:5b:0e:2e:19:00
[ 5569.561060] wlan0: send auth to 1a:5b:0e:2e:19:00 (try 1/3)
[ 5569.676064] wlan0: send auth to 1a:5b:0e:2e:19:00 (try 2/3)
[ 5569.684611] wlan0: authenticated
[ 5569.696111] wlan0: associate with 1a:5b:0e:2e:19:00 (try 1/3)
[ 5569.704858] wlan0: RX AssocResp from 1a:5b:0e:2e:19:00 (capab=0x401 status=0 aid=1)
[ 5569.714388] wlan0: associated
[ 5569.722757] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 5671.276382] ath10k_pci 0000:00:00.0: peer-unmap-event: unknown peer id 1
[ 5798.731507] wlan0: authenticate with 1a:5b:0e:2e:19:00
[ 5798.744330] wlan0: send auth to 1a:5b:0e:2e:19:00 (try 1/3)
[ 5798.751183] wlan0: authenticated
[ 5798.775710] wlan0: associate with 1a:5b:0e:2e:19:00 (try 1/3)
[ 5798.798089] wlan0: RX AssocResp from 1a:5b:0e:2e:19:00 (capab=0x401 status=0 aid=1)
[ 5798.827923] wlan0: associated
[ 6174.325438] wlan0: deauthenticating from 1a:5b:0e:2e:19:00 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6174.335470] ath10k_pci 0000:00:00.0: peer-unmap-event: unknown peer id 1
[ 6174.753802] ath: EEPROM regdomain: 0x82d4
[ 6174.758000] ath: EEPROM indicates we should expect a country code
[ 6174.764426] ath: doing EEPROM country->regdmn map search
[ 6174.769971] ath: country maps to regdmn code: 0x37
[ 6174.774994] ath: Country alpha2 being used: ES
[ 6174.779593] ath: Regpair used: 0x37
[ 6174.783234] ath: regdomain 0x82d4 dynamically updated by user
[ 6174.789266] ath: EEPROM regdomain: 0x82d4
[ 6174.793429] ath: EEPROM indicates we should expect a country code
[ 6174.799738] ath: doing EEPROM country->regdmn map search
[ 6174.805235] ath: country maps to regdmn code: 0x37
[ 6174.810179] ath: Country alpha2 being used: ES
[ 6174.814779] ath: Regpair used: 0x37
[ 6174.818447] ath: regdomain 0x82d4 dynamically updated by user
[ 6178.277914] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[ 6178.285787] ath10k_pci 0000:00:00.0: msdu-desc: 2500  skid: 32
[ 6178.316107] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[ 6178.327503] ath10k_pci 0000:00:00.0: wmi print 'free: 117872 iram: 22788 sram: 26020'
[ 6178.625631] ath10k_pci 0000:00:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 6178.637423] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6181.803691] wlan0: authenticate with 1a:5b:0e:2e:19:00
[ 6182.037301] wlan0: send auth to 1a:5b:0e:2e:19:00 (try 1/3)
[ 6182.052211] wlan0: authenticated
[ 6182.064444] wlan0: associate with 1a:5b:0e:2e:19:00 (try 1/3)
[ 6182.083023] wlan0: RX AssocResp from 1a:5b:0e:2e:19:00 (capab=0x401 status=0 aid=1)
[ 6182.093619] wlan0: associated
[ 6182.102175] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 6550.204035] wlan0: deauthenticating from 1a:5b:0e:2e:19:00 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6550.214114] ath10k_pci 0000:00:00.0: peer-unmap-event: unknown peer id 1
[ 6553.421807] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[ 6553.429621] ath10k_pci 0000:00:00.0: msdu-desc: 2500  skid: 32
[ 6553.460165] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[ 6553.471501] ath10k_pci 0000:00:00.0: wmi print 'free: 117872 iram: 22788 sram: 26020'
[ 6553.761446] ath10k_pci 0000:00:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 6553.773142] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6557.046393] wlan0: authenticate with 1a:5b:0e:2e:19:00
[ 6557.271672] wlan0: send auth to 1a:5b:0e:2e:19:00 (try 1/3)
[ 6557.285072] wlan0: authenticated
[ 6557.293172] wlan0: associate with 1a:5b:0e:2e:19:00 (try 1/3)
[ 6557.307374] wlan0: RX AssocResp from 1a:5b:0e:2e:19:00 (capab=0x401 status=0 aid=1)
[ 6557.317285] wlan0: associated
[ 6557.326221] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 7722.095937] wlan0: AP 1a:5b:0e:2e:19:00 changed bandwidth, new config is 5220 MHz, width 2 (5230/0 MHz)
[ 8236.781516] wlan0: deauthenticated from 1a:5b:0e:2e:19:00 (Reason: 6=CLASS2_FRAME_FROM_NONAUTH_STA)
[ 8236.791639] ath10k_pci 0000:00:00.0: peer-unmap-event: unknown peer id 1
[ 8236.866086] wlan0: authenticate with 1a:5b:0e:2e:19:00
[ 8237.089784] wlan0: send auth to 1a:5b:0e:2e:19:00 (try 1/3)
[ 8237.104036] wlan0: authenticated
[ 8237.120414] wlan0: associate with 1a:5b:0e:2e:19:00 (try 1/3)
[ 8237.133184] wlan0: RX AssocResp from 1a:5b:0e:2e:19:00 (capab=0x401 status=0 aid=1)
[ 8237.143180] wlan0: associated
[ 8257.726756] wlan0: deauthenticating from 1a:5b:0e:2e:19:00 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 8257.736777] ath10k_pci 0000:00:00.0: peer-unmap-event: unknown peer id 1
[ 8260.957496] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[ 8260.965317] ath10k_pci 0000:00:00.0: msdu-desc: 2500  skid: 32
[ 8260.995627] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[ 8261.006956] ath10k_pci 0000:00:00.0: wmi print 'free: 117872 iram: 22788 sram: 26020'
[ 8261.299781] ath10k_pci 0000:00:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 8261.311461] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 8264.620055] wlan0: authenticate with 1a:5b:0e:2e:19:00
[ 8264.845698] wlan0: send auth to 1a:5b:0e:2e:19:00 (try 1/3)
[ 8264.853295] wlan0: authenticated
[ 8264.865385] wlan0: associate with 1a:5b:0e:2e:19:00 (try 1/3)
[ 8264.881454] wlan0: RX AssocResp from 1a:5b:0e:2e:19:00 (capab=0x401 status=0 aid=1)
[ 8264.891684] wlan0: associated
[ 8264.897097] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[13122.099162] wlan0: AP 1a:5b:0e:2e:19:00 changed bandwidth, new config is 5220 MHz, width 2 (5230/0 MHz)
[14713.285680] wlan0: deauthenticating from 1a:5b:0e:2e:19:00 by local choice (Reason: 3=DEAUTH_LEAVING)
[14713.295629] ath10k_pci 0000:00:00.0: peer-unmap-event: unknown peer id 1
[14716.654731] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[14716.662602] ath10k_pci 0000:00:00.0: msdu-desc: 2500  skid: 32
[14716.693111] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[14716.704438] ath10k_pci 0000:00:00.0: wmi print 'free: 117872 iram: 22788 sram: 26020'
[14716.994660] ath10k_pci 0000:00:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[14717.006377] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[14744.123600] wlan0: authenticate with 1a:5b:0e:2e:19:00
[14744.349260] wlan0: send auth to 1a:5b:0e:2e:19:00 (try 1/3)
[14744.356750] wlan0: authenticated
[14744.367374] wlan0: associate with 1a:5b:0e:2e:19:00 (try 1/3)
[14744.380133] wlan0: RX AssocResp from 1a:5b:0e:2e:19:00 (capab=0x401 status=0 aid=2)
[14744.390103] wlan0: associated
[14744.398837] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[16722.021272] wlan0: AP 1a:5b:0e:2e:19:00 changed bandwidth, new config is 5180 MHz, width 2 (5190/0 MHz)