Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 2012.07 [ ,uart_en] (Nov 02 2017 - 17:14:39)
- smem ram ptable found: ver: 0 len: 5
- DRAM: 494 MiB
- NAND: SF: Unsupported manufacturer 00
- ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
- 256 MiB
- PCI0 Link Intialized
- PCI1 Link Intialized
- In: serial
- Out: serial
- Err: serial
- cdp: get part failed for 0:HLOS
- cdp: get part failed for rootfs
- Net: MAC1 addr:40:31:3c:dc:1e:b2
- athrs17_reg_init: complete
- athrs17_vlan_config ...done
- S17c init done
- MAC2 addr:40:31:3c:dc:1e:b3
- eth0, eth1
- Hit any key to stop autoboot: 0
- NAND read: device 0 offset 0x800000, size 0x400000
- 4194304 bytes read: OK
- Image Name: ARM OpenWrt Linux-5.4.154
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 2942027 Bytes = 2.8 MiB
- Load Address: 42208000
- Entry Point: 42208000
- Verifying Checksum ... OK
- Loading Kernel Image ... OK
- OK
- device nand0 <nand>, # parts = 9
- #: name size offset mask_flags
- 0: Bdata 0x00080000 0x00600000 0
- 1: crash 0x00080000 0x00680000 0
- 2: crash_syslog 0x00080000 0x00700000 0
- 3: rsvd 0x00080000 0x00780000 0
- 4: kernel0 0x00400000 0x00800000 0
- 5: kernel1 0x00400000 0x00c00000 0
- 6: rootfs0 0x02800000 0x01000000 0
- 7: rootfs1 0x02800000 0x03800000 0
- 8: overlay 0x0a000000 0x06000000 0
- active partition: nand0,0 - (Bdata) 0x00080000 @ 0x00600000
- defaults:
- mtdids : none
- mtdparts: none
- Setting up atags for msm partition: Bdata
- Setting up atags for msm partition: crash
- Setting up atags for msm partition: crash_syslog
- Setting up atags for msm partition: rsvd
- Setting up atags for msm partition: kernel0
- Setting up atags for msm partition: kernel1
- Setting up atags for msm partition: rootfs0
- Setting up atags for msm partition: rootfs1
- Setting up atags for msm partition: overlay
- Using machid 0x1260 from environment
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0
- [ 0.000000] Linux version 5.4.154 (droid@droid-vm) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16325-88151b8303)) #0 SMP Sun Oct 24 09:01:35 2021
- [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
- [ 0.000000] CPU: div instructions available: patching division code
- [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
- [ 0.000000] OF: fdt: Machine model: Xiaomi Mi Router HD (R3D)
- [ 0.000000] printk: debug: ignoring loglevel setting.
- [ 0.000000] Memory policy: Data cache writealloc
- [ 0.000000] On node 0 totalpages: 120832
- [ 0.000000] Normal zone: 1080 pages used for memmap
- [ 0.000000] Normal zone: 0 pages reserved
- [ 0.000000] Normal zone: 120832 pages, LIFO batch:31
- [ 0.000000] percpu: Embedded 15 pages/cpu s30156 r8192 d23092 u61440
- [ 0.000000] pcpu-alloc: s30156 r8192 d23092 u61440 alloc=15*4096
- [ 0.000000] pcpu-alloc: [0] 0 [0] 1
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 119752
- [ 0.000000] Kernel command line: rootfstype=squashfs noinitrd ignore_loglevel nosmt nosmp
- [ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8 uart_en=1
- [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
- [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
- [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
- [ 0.000000] Memory: 468724K/483328K available (6233K kernel code, 235K rwdata, 1632K rodata, 1024K init, 229K bss, 14604K reserved, 0K cma-reserved, 0K highmem)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] rcu: Hierarchical RCU implementation.
- [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
- [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
- [ 0.000000] random: get_random_bytes called from start_kernel+0x340/0x4ec with crng_init=0
- [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
- [ 0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
- [ 0.000024] Switching to timer-based delay loop, resolution 160ns
- [ 0.000253] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
- [ 0.000272] pid_max: default: 32768 minimum: 301
- [ 0.000486] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.000504] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.001560] CPU: Testing write buffer coherency: ok
- [ 0.002700] Setting up static identity map for 0x42300000 - 0x42300060
- [ 0.002876] rcu: Hierarchical SRCU implementation.
- [ 0.004765] smp: Bringing up secondary CPUs ...
- [ 0.004785] smp: Brought up 1 node, 1 CPU
- [ 0.004799] SMP: Total of 1 processors activated (12.50 BogoMIPS).
- [ 0.004809] CPU: All CPU(s) started in SVC mode.
- [ 0.015448] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
- [ 0.015604] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.015631] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
- [ 0.015776] pinctrl core: initialized pinctrl subsystem
- [ 0.016980] NET: Registered protocol family 16
- [ 0.017309] DMA: preallocated 256 KiB pool for atomic coherent allocations
- [ 0.018416] cpuidle: using governor ladder
- [ 0.018432] cpuidle: using governor menu
- [ 0.048977] usbcore: registered new interface driver usbfs
- [ 0.049055] usbcore: registered new interface driver hub
- [ 0.049123] usbcore: registered new device driver usb
- [ 0.049184] pps_core: LinuxPPS API ver. 1 registered
- [ 0.049199] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- [ 0.049240] PTP clock support registered
- [ 0.050024] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
- [ 0.051196] clocksource: Switched to clocksource dg_timer
- [ 0.052255] thermal_sys: Registered thermal governor 'step_wise'
- [ 0.054656] NET: Registered protocol family 2
- [ 0.054819] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
- [ 0.055486] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
- [ 0.055526] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
- [ 0.055570] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
- [ 0.055623] TCP: Hash tables configured (established 4096 bind 4096)
- [ 0.055726] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
- [ 0.055753] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
- [ 0.055996] NET: Registered protocol family 1
- [ 0.056055] PCI: CLS 0 bytes, default 64
- [ 0.057468] workingset: timestamp_bits=14 max_order=17 bucket_order=3
- [ 0.064228] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.064244] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.104865] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator
- [ 0.104996] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator
- [ 0.105108] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator
- [ 0.105368] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
- [ 0.105397] qcom-pcie 1b500000.pci: Parsing ranges property...
- [ 0.105444] qcom-pcie 1b500000.pci: IO 0x0fe00000..0x0fefffff -> 0x0fe00000
- [ 0.105481] qcom-pcie 1b500000.pci: MEM 0x08000000..0x0fdfffff -> 0x08000000
- [ 0.327155] qcom-pcie 1b500000.pci: Link up
- [ 0.327320] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
- [ 0.327344] pci_bus 0000:00: root bus resource [bus 00-ff]
- [ 0.327364] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
- [ 0.327382] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
- [ 0.327399] pci_bus 0000:00: scanning bus
- [ 0.327452] pci 0000:00:00.0: [17cb:0101] type 01 class 0xff0000
- [ 0.327616] pci 0000:00:00.0: supports D1
- [ 0.327633] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
- [ 0.327654] pci 0000:00:00.0: PME# disabled
- [ 0.331861] pci_bus 0000:00: fixups for bus
- [ 0.331890] PCI: bus0: Fast back to back transfers disabled
- [ 0.331912] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
- [ 0.332066] pci_bus 0000:01: scanning bus
- [ 0.332250] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000
- [ 0.332601] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
- [ 0.333733] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
- [ 0.333780] pci 0000:01:00.0: PME# disabled
- [ 0.338052] pci_bus 0000:01: fixups for bus
- [ 0.338127] PCI: bus1: Fast back to back transfers disabled
- [ 0.338144] pci_bus 0000:01: bus scan returning with max=01
- [ 0.338167] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
- [ 0.338193] pci_bus 0000:00: bus scan returning with max=ff
- [ 0.338229] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
- [ 0.338254] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
- [ 0.338381] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
- [ 0.338408] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
- [ 0.338613] pcieport 0000:00:00.0: assign IRQ: got 35
- [ 0.339172] pcieport 0000:00:00.0: AER: enabled with IRQ 36
- [ 0.339736] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator
- [ 0.339872] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator
- [ 0.339986] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator
- [ 0.340232] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
- [ 0.340256] qcom-pcie 1b700000.pci: Parsing ranges property...
- [ 0.340299] qcom-pcie 1b700000.pci: IO 0x31e00000..0x31efffff -> 0x31e00000
- [ 0.340330] qcom-pcie 1b700000.pci: MEM 0x2e000000..0x31dfffff -> 0x2e000000
- [ 0.568576] qcom-pcie 1b700000.pci: Link up
- [ 0.568733] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
- [ 0.568754] pci_bus 0001:00: root bus resource [bus 00-ff]
- [ 0.568772] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
- [ 0.568788] pci_bus 0001:00: scanning bus
- [ 0.568833] pci 0001:00:00.0: [17cb:0101] type 01 class 0xff0000
- [ 0.568974] pci 0001:00:00.0: supports D1
- [ 0.568989] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
- [ 0.569008] pci 0001:00:00.0: PME# disabled
- [ 0.573166] pci_bus 0001:00: fixups for bus
- [ 0.573190] PCI: bus0: Fast back to back transfers disabled
- [ 0.573209] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
- [ 0.573348] pci_bus 0001:01: scanning bus
- [ 0.573546] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000
- [ 0.573920] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
- [ 0.575142] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
- [ 0.575192] pci 0001:01:00.0: PME# disabled
- [ 0.575449] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0001:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
- [ 0.579499] pci_bus 0001:01: fixups for bus
- [ 0.579578] PCI: bus1: Fast back to back transfers disabled
- [ 0.579594] pci_bus 0001:01: bus scan returning with max=01
- [ 0.579615] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
- [ 0.579636] pci_bus 0001:00: bus scan returning with max=ff
- [ 0.579664] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
- [ 0.579687] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
- [ 0.579819] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
- [ 0.579840] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
- [ 0.580034] pcieport 0001:00:00.0: assign IRQ: got 37
- [ 0.580555] pcieport 0001:00:00.0: AER: enabled with IRQ 38
- [ 0.583128] L2 @ QSB rate. Forcing new rate.
- [ 0.583349] L2 @ 384000 KHz
- [ 0.583522] CPU0 @ 800000 KHz
- [ 0.583535] CPU1 @ QSB rate. Forcing new rate.
- [ 0.583610] CPU1 @ 384000 KHz
- [ 0.587179] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
- [ 0.589260] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
- [ 0.590058] msm_serial 16340000.serial: msm_serial: detected port #0
- [ 0.590108] msm_serial 16340000.serial: uartclk = 7372800
- [ 0.590175] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 39, base_baud = 460800) is a MSM
- [ 0.590213] msm_serial: console setup on port #0
- [ 1.531535] printk: console [ttyMSM0] enabled
- [ 1.536520] msm_serial: driver initialized
- [ 1.545721] loop: module loaded
- [ 1.547275] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xaa
- [ 1.547672] nand: Macronix MX30UF2G18AC
- [ 1.554362] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
- [ 1.558000] 19 fixed-partitions partitions found on MTD device qcom_nand.0
- [ 1.565569] Creating 19 MTD partitions on "qcom_nand.0":
- [ 1.572415] 0x000000000000-0x000000040000 : "SBL1"
- [ 1.579173] 0x000000040000-0x0000000c0000 : "MIBIB"
- [ 1.584174] 0x0000000c0000-0x000000140000 : "SBL2"
- [ 1.588861] 0x000000140000-0x0000001c0000 : "SBL3"
- [ 1.593781] 0x0000001c0000-0x000000240000 : "DDRCONFIG"
- [ 1.598504] 0x000000240000-0x0000002c0000 : "SSD"
- [ 1.603665] 0x0000002c0000-0x000000340000 : "TZ"
- [ 1.607487] random: fast init done
- [ 1.612446] 0x000000340000-0x0000003c0000 : "RPM"
- [ 1.616369] 0x0000003c0000-0x0000004c0000 : "APPSBL"
- [ 1.622047] 0x0000004c0000-0x000000540000 : "APPSBLENV"
- [ 1.626168] 0x000000540000-0x0000005c0000 : "ART"
- [ 1.631124] 0x0000005c0000-0x000000600000 : "BOOTCONFIG"
- [ 1.635686] 0x000000600000-0x000000680000 : "bdata"
- [ 1.641373] 0x000000680000-0x000000700000 : "crash"
- [ 1.646026] 0x000000700000-0x000000780000 : "crash_syslog"
- [ 1.650841] 0x000000780000-0x000000800000 : "rsvd"
- [ 1.656477] 0x000000800000-0x000000c00000 : "kernel_dup"
- [ 1.666732] 0x000000c00000-0x000001000000 : "kernel"
- [ 1.674046] 0x000001000000-0x000010000000 : "ubi"
- [ 1.940085] random: crng init done
- [ 2.053408] libphy: ipq8064_mdio_bus: probed
- [ 2.068429] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii
- [ 2.887557] ar8327: qca,phy-rgmii-en is not specified
- [ 2.888092] libphy: Fixed MDIO Bus: probed
- [ 2.892307] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found
- [ 2.895588] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found
- [ 2.903653] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
- [ 2.909699] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
- [ 2.915850] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000
- [ 2.923266] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
- [ 2.929008] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
- [ 2.936820] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
- [ 2.944724] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
- [ 2.950445] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
- [ 2.957907] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
- [ 2.964683] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
- [ 2.972215] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
- [ 2.979176] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
- [ 2.986272] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
- [ 2.994116] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
- [ 3.001223] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
- [ 3.007820] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
- [ 3.014111] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000
- [ 3.021543] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
- [ 3.027269] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
- [ 3.035070] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
- [ 3.042970] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
- [ 3.048711] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
- [ 3.056157] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
- [ 3.062933] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
- [ 3.070411] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
- [ 3.077522] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
- [ 3.084670] i2c /dev entries driver
- [ 3.094576] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
- [ 3.095607] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
- [ 3.103468] sdhci: Secure Digital Host Controller Interface driver
- [ 3.110077] sdhci: Copyright(c) Pierre Ossman
- [ 3.116415] sdhci-pltfm: SDHCI platform and OF driver helper
- [ 3.123053] NET: Registered protocol family 10
- [ 3.127772] Segment Routing with IPv6
- [ 3.130831] NET: Registered protocol family 17
- [ 3.134672] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
- [ 3.139066] 8021q: 802.1Q VLAN Support v1.8
- [ 3.152129] Registering SWP/SWPB emulation handler
- [ 3.176608] qcom_rpm 108000.rpm: RPM firmware 3.0.16777372
- [ 3.189783] s1a: Bringing 0uV into 1050000-1050000uV
- [ 3.190048] s1a: supplied by regulator-dummy
- [ 3.194037] s1b: Bringing 0uV into 1050000-1050000uV
- [ 3.198257] s1b: supplied by regulator-dummy
- [ 3.203231] s2a: Bringing 0uV into 800000-800000uV
- [ 3.207480] s2a: supplied by regulator-dummy
- [ 3.212080] s2b: Bringing 0uV into 800000-800000uV
- [ 3.216500] s2b: supplied by regulator-dummy
- [ 3.228211] UBI: auto-attach mtd18
- [ 3.228232] ubi0: attaching mtd18
- [ 6.100228] ubi0: scanning is finished
- [ 6.110377] ubi0: attached mtd18 (name "ubi", size 240 MiB)
- [ 6.110397] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- [ 6.114832] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- [ 6.121759] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
- [ 6.128547] ubi0: good PEBs: 1919, bad PEBs: 1, corrupted PEBs: 0
- [ 6.135379] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
- [ 6.141627] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1641775890
- [ 6.148691] ubi0: available PEBs: 0, total reserved PEBs: 1919, PEBs reserved for bad PEB handling: 39
- [ 6.158814] block ubiblock0_0: created from ubi0:0(rootfs)
- [ 6.167150] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
- [ 6.172619] hctosys: unable to open rtc devi▒[ 6.187560] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
- [ 6.188198] Freeing unused kernel memory: 1024K
- [ 6.211670] Run /sbin/init as init process
- [ 6.461207] init: Console is alive
- [ 6.461338] init: - watchdog -
- [ 7.385289] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 7.468485] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 7.472512] SCSI subsystem initialized
- [ 7.478782] libata version 3.00 loaded.
- [ 7.480740] ahci 29000000.sata: 29000000.sata supply ahci not found, using dummy regulator
- [ 7.481565] ahci 29000000.sata: 29000000.sata supply phy not found, using dummy regulator
- [ 7.489873] ahci 29000000.sata: 29000000.sata supply target not found, using dummy regulator
- [ 7.500195] ahci 29000000.sata: forcing port_map 0x0 -> 0x1
- [ 7.506611] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
- [ 7.511880] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
- [ 7.520953] scsi host0: ahci
- [ 7.528933] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 26
- [ 7.864006] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
- [ 7.865079] ata1.00: ATA-8: ST1000VM002-1SD102, SC11, max UDMA/133
- [ 7.869093] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32)
- [ 7.890776] ata1.00: configured for UDMA/133
- [ 7.891192] scsi 0:0:0:0: Direct-Access ATA ST1000VM002-1SD1 SC11 PQ: 0 ANSI: 5
- [ 7.898650] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
- [ 7.902275] sd 0:0:0:0: [sda] 4096-byte physical blocks
- [ 7.909788] sd 0:0:0:0: [sda] Write Protect is off
- [ 7.914860] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
- [ 7.919945] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- [ 7.974027] sda: sda1
- [ 7.976311] sd 0:0:0:0: [sda] Attached SCSI disk
- [ 7.980525] ehci-fsl: Freescale EHCI Host controller driver
- [ 7.982594] ehci-platform: EHCI generic platform driver
- [ 8.000369] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 8.001821] ohci-platform: OHCI generic platform driver
- [ 8.008265] dwc3-qcom 110f8800.usb3: IRQ hs_phy_irq not found
- [ 8.010632] dwc3-qcom 110f8800.usb3: IRQ dp_hs_phy_irq not found
- [ 8.016542] dwc3-qcom 110f8800.usb3: IRQ dm_hs_phy_irq not found
- [ 8.022592] dwc3-qcom 110f8800.usb3: IRQ ss_phy_irq not found
- [ 8.030208] dwc3-qcom 100f8800.usb3: IRQ hs_phy_irq not found
- [ 8.034260] dwc3-qcom 100f8800.usb3: IRQ dp_hs_phy_irq not found
- [ 8.039956] dwc3-qcom 100f8800.usb3: IRQ dm_hs_phy_irq not found
- [ 8.046050] dwc3-qcom 100f8800.usb3: IRQ ss_phy_irq not found
- [ 8.054136] dwc3 11000000.dwc3: Failed to get clk 'ref': -2
- [ 8.121977] dwc3 10000000.dwc3: Failed to get clk 'ref': -2
- [ 8.197031] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
- [ 8.197081] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
- [ 8.201645] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
- [ 8.209089] xhci-hcd xhci-hcd.0.auto: irq 42, io mem 0x11000000
- [ 8.218617] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
- [ 8.224319] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
- [ 8.229801] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
- [ 8.238115] hub 1-0:1.0: USB hub found
- [ 8.244062] hub 1-0:1.0: 1 port detected
- [ 8.248083] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
- [ 8.252199] hub 2-0:1.0: USB hub found
- [ 8.259930] hub 2-0:1.0: 1 port detected
- [ 8.263736] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
- [ 8.267475] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
- [ 8.272965] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
- [ 8.280341] xhci-hcd xhci-hcd.1.auto: irq 43, io mem 0x10000000
- [ 8.289903] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
- [ 8.295667] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
- [ 8.301150] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
- [ 8.309224] hub 3-0:1.0: USB hub found
- [ 8.315399] hub 3-0:1.0: 1 port detected
- [ 8.319357] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
- [ 8.323507] hub 4-0:1.0: USB hub found
- [ 8.331295] hub 4-0:1.0: 1 port detected
- [ 8.338624] usbcore: registered new interface driver usb-storage
- [ 8.339587] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 8.355430] init: - preinit -
- strings: standard output: Broken pipe
- [ 9.824995] dwmac1000: Master AXI performs any burst length
- [ 9.825028] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
- [ 9.829377] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
- [ 9.837557] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
- [ 9.846457] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
- [ 9.853849] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
- [ 9.862344] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 14.050097] mount_root: loading kmods from internal overlay
- [ 14.065483] kmodloader: loading kernel modules from //etc/modules-boot.d/*
- [ 14.066905] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
- [ 14.840261] UBIFS (ubi0:1): Mounting in unauthenticated mode
- [ 14.919403] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 153
- [ 14.977127] UBIFS (ubi0:1): recovery needed
- [ 15.175648] UBIFS (ubi0:1): recovery completed
- [ 15.175734] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
- [ 15.178979] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
- [ 15.186954] UBIFS (ubi0:1): FS size: 226017280 bytes (215 MiB, 1780 LEBs), journal size 11300864 bytes (10 MiB, 89 LEBs)
- [ 15.196830] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
- [ 15.207758] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 7E9F431F-F8ED-445A-8F1F-B35865EF75A0, small LPT model
- [ 15.217398] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
- [ 15.232044] block: extroot: not configured
- [ 15.232360] UBIFS (ubi0:1): un-mount UBI device 0
- [ 15.236451] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
- [ 15.244473] UBIFS (ubi0:1): Mounting in unauthenticated mode
- [ 15.301769] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 154
- [ 15.490984] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
- [ 15.491009] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
- [ 15.497853] UBIFS (ubi0:1): FS size: 226017280 bytes (215 MiB, 1780 LEBs), journal size 11300864 bytes (10 MiB, 89 LEBs)
- [ 15.507763] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
- [ 15.518690] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 7E9F431F-F8ED-445A-8F1F-B35865EF75A0, small LPT model
- [ 15.529715] mount_root: loading kmods from internal overlay
- [ 15.550313] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
- [ 15.552099] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
- [ 16.235564] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
- [ 16.241405] block: extroot: not configured
- [ 16.243651] mount_root: switching to ubifs overlay
- [ 16.254553] urandom-seed: Seeding with /etc/urandom.seed
- [ 16.299808] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
- [ 16.336543] procd: - early -
- [ 16.336637] procd: - watchdog -
- [ 16.928188] procd: - watchdog -
- [ 16.936386] procd: - ubus -
- [ 16.993329] procd: - init -
- Please press Enter to activate this console.
- [ 17.657184] urngd: v1.0.2 started.
- [ 17.674731] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 17.785677] Key type cifs.idmap registered
- [ 17.790636] ntfs: driver 2.1.32 [Flags: R/O MODULE].
- [ 17.800743] tun: Universal TUN/TAP device driver, 1.6
- [ 17.812648] l2tp_core: L2TP core driver, V2.0
- [ 17.814099] l2tp_netlink: L2TP netlink interface
- [ 17.817603] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
- [ 17.822983] gre: GRE over IPv4 demultiplexor driver
- [ 17.827848] ip_gre: GRE over IPv4 tunneling driver
- [ 17.834822] ip6_gre: GRE over IPv6 tunneling driver
- [ 17.900586] i2c-gpio i2c_gpio_0: using lines 496 (SDA) and 497 (SCL)
- [ 17.900905] i2c-gpio i2c_gpio_1: using lines 467 (SDA) and 468 (SCL)
- [ 17.917227] Bridge firewalling registered
- [ 17.919090] Loading modules backported from Linux version v5.10.68-0-g4d8524048a35
- [ 17.920212] Backport generated by backports.git v5.10.68-1-0-ga4f9ba32
- [ 17.955990] xt_time: kernel timezone is -0000
- [ 17.995017] emc2305 0-002f: emc2301 detected
- [ 18.001834] lm75 1-0048: hwmon1: sensor 'tmp75'
- [ 18.068628] PPP generic driver version 2.4.2
- [ 18.070657] PPP MPPE Compression module registered
- [ 18.073665] NET: Registered protocol family 24
- [ 18.078164] PPTP driver version 0.8.5
- [ 18.108721] ath10k_pci 0000:01:00.0: assign IRQ: got 35
- [ 18.117099] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
- [ 18.117185] ath10k_pci 0000:01:00.0: enabling bus mastering
- [ 18.122798] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
- [ 19.535156] ath10k_pci 0000:01:00.0: Unknown FW IE: 30
- [ 19.535188] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
- [ 19.539187] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
- [ 19.551085] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl crc32 7ea63dc5
- [ 21.889728] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 85498734
- [ 25.564236] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
- [ 25.653113] ath: EEPROM regdomain sanitized
- [ 25.653152] ath: EEPROM regdomain: 0x64
- [ 25.656108] ath: EEPROM indicates we should expect a direct regpair map
- [ 25.659948] ath: Country alpha2 being used: 00
- [ 25.666671] ath: Regpair used: 0x64
- [ 25.681374] ath10k_pci 0001:01:00.0: assign IRQ: got 37
- [ 25.684446] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
- [ 25.685465] ath10k_pci 0001:01:00.0: enabling bus mastering
- [ 25.692337] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
- [ 26.106063] ath10k_pci 0001:01:00.0: Unknown FW IE: 30
- [ 26.106095] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
- [ 26.110093] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
- [ 26.121133] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9980-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl crc32 b36a12bf
- [ 26.192573] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:2 crc32 08fa09f2
- [ 27.449122] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
- [ 27.543102] ath: EEPROM regdomain sanitized
- [ 27.543141] ath: EEPROM regdomain: 0x64
- [ 27.546097] ath: EEPROM indicates we should expect a direct regpair map
- [ 27.549937] ath: Country alpha2 being used: 00
- [ 27.556662] ath: Regpair used: 0x64
- [ 27.572943] l2tp_ppp: PPPoL2TP kernel driver, V2.0
- [ 27.574218] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 32.325903] dwmac1000: Master AXI performs any burst length
- [ 32.325933] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
- [ 32.330281] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
- [ 32.338443] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
- [ 32.347369] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
- [ 32.355324] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
- [ 32.368131] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
- [ 32.403091] br-lan: port 1(eth1.1) entered blocking state
- [ 32.403119] br-lan: port 1(eth1.1) entered disabled state
- [ 32.407620] device eth1.1 entered promiscuous mode
- [ 32.412934] device eth1 entered promiscuous mode
- [ 32.428137] br-lan: port 1(eth1.1) entered blocking state
- [ 32.428164] br-lan: port 1(eth1.1) entered forwarding state
- [ 32.454705] dwmac1000: Master AXI performs any burst length
- [ 32.454738] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
- [ 32.459085] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
- [ 32.467346] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
- [ 32.476172] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
- [ 32.483916] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
- [ 32.507316] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
- [ 33.371685] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Add Comment
Please, Sign In to add comment