Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- [ 0.000000] Linux version 5.4.158 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16399-c67509efd7)) #0 SMP Sun Dec 5 12:54:20 2021
- [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
- [ 0.000000] printk: bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
- [ 0.000000] MIPS: machine is FPT AP-AX1800C
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] VPE topology {2,2} total 4
- [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
- [ 0.000000] HighMem empty
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
- [ 0.000000] percpu: Embedded 14 pages/cpu s26768 r8192 d22384 u57344
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
- [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
- [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
- [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
- [ 0.000000] Writing ErrCtl register=00004820
- [ 0.000000] Readback ErrCtl register=00004820
- [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
- [ 0.000000] Memory: 244776K/262144K available (6061K kernel code, 209K rwdata, 744K rodata, 7308K init, 238K bss, 17368K reserved, 0K cma-reserved, 0K highmem)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
- [ 0.000000] rcu: Hierarchical RCU implementation.
- [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
- [ 0.000000] NR_IRQS: 256
- [ 0.000000] random: get_random_bytes called from 0x806dda3c with crng_init=0
- [ 0.000000] CPU Clock: 880MHz
- [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
- [ 0.000008] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
- [ 0.007815] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360)
- [ 0.042008] pid_max: default: 32768 minimum: 301
- [ 0.046788] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.054015] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.064489] rcu: Hierarchical SRCU implementation.
- [ 0.069938] smp: Bringing up secondary CPUs ...
- [ 8.812584] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 8.812595] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 8.812608] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
- [ 8.812708] CPU1 revision is: 0001992f (MIPS 1004Kc)
- [ 0.102700] Synchronize counters for CPU 1: done.
- [ 8.531994] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 8.532002] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 8.532010] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
- [ 8.532067] CPU2 revision is: 0001992f (MIPS 1004Kc)
- [ 0.167410] Synchronize counters for CPU 2: done.
- [ 8.595353] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 8.595362] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 8.595371] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
- [ 8.595430] CPU3 revision is: 0001992f (MIPS 1004Kc)
- [ 0.225263] Synchronize counters for CPU 3: done.
- [ 0.255136] smp: Brought up 1 node, 4 CPUs
- [ 0.263365] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
- [ 0.273044] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
- [ 0.280071] pinctrl core: initialized pinctrl subsystem
- [ 0.286924] NET: Registered protocol family 16
- [ 0.314707] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
- [ 0.326376] clocksource: Switched to clocksource GIC
- [ 0.332815] thermal_sys: Registered thermal governor 'step_wise'
- [ 0.333308] NET: Registered protocol family 2
- [ 0.343746] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
- [ 0.351783] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
- [ 0.360104] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
- [ 0.367703] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
- [ 0.374789] TCP: Hash tables configured (established 2048 bind 2048)
- [ 0.381230] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
- [ 0.387711] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
- [ 0.394933] NET: Registered protocol family 1
- [ 0.399248] PCI: CLS 0 bytes, default 32
- [ 8.162365] 4 CPUs re-calibrate udelay(lpj = 1163264)
- [ 8.169215] workingset: timestamp_bits=14 max_order=16 bucket_order=2
- [ 8.180226] random: fast init done
- [ 8.190883] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 8.196649] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 8.209977] mt7621_gpio 1e000600.gpio: registering 32 gpios
- [ 8.215862] mt7621_gpio 1e000600.gpio: registering 32 gpios
- [ 8.221676] mt7621_gpio 1e000600.gpio: registering 32 gpios
- [ 8.228052] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 8.237911] printk: console [ttyS0] disabled
- [ 8.242218] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
- [ 8.251208] printk: console [ttyS0] enabled
- [ 8.251208] printk: console [ttyS0] enabled
- [ 8.259467] printk: bootconsole [early0] disabled
- [ 8.259467] printk: bootconsole [early0] disabled
- [ 8.271242] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388
- [ 8.278802] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xdc
- [ 8.285145] nand: Macronix MX30LF4G18AC
- [ 8.288981] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
- [ 8.296540] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
- [ 8.303094] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134
- [ 8.310396] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134
- [ 8.317693] Scanning device for bad blocks
- [ 13.526754] 7 fixed-partitions partitions found on MTD device mt7621-nand
- [ 13.533528] Creating 7 MTD partitions on "mt7621-nand":
- [ 13.538765] 0x000000000000-0x000000080000 : "Bootloader"
- [ 13.545398] 0x000000080000-0x000000100000 : "Config"
- [ 13.551779] 0x000000100000-0x000000180000 : "Factory"
- [ 13.558170] 0x000000180000-0x000003180000 : "firmware"
- [ 13.564970] 0x000003180000-0x000006180000 : "firmware2"
- [ 13.571780] 0x000006180000-0x000006980000 : "aei_data_ext"
- [ 13.578813] 0x000006980000-0x000006d80000 : "aei_data"
- [ 13.586704] libphy: Fixed MDIO Bus: probed
- [ 13.616775] libphy: mdio: probed
- [ 13.620298] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
- [ 13.628749] mtk_soc_eth 1e100000.ethernet: generated random MAC address 36:08:b3:71:3e:04
- [ 13.637867] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
- [ 13.647327] i2c-mt7621 1e000900.i2c: clock 100 kHz
- [ 13.653551] mt7621-pci 1e140000.pcie: Parsing DT failed
- [ 13.661409] NET: Registered protocol family 10
- [ 13.667387] Segment Routing with IPv6
- [ 13.671250] NET: Registered protocol family 17
- [ 13.675791] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
- [ 13.688990] 8021q: 802.1Q VLAN Support v1.8
- [ 13.695173] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
- [ 13.761162] libphy: dsa slave smi: probed
- [ 13.765646] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY]
- [ 13.775469] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY]
- [ 13.785773] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
- [ 13.797016] DSA: tree 0 setup
- [ 13.800346] rt2880-pinmux pinctrl: pcie is already enabled
- [ 13.805990] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
- [ 13.813579] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
- [ 13.920750] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
- [ 13.926354] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
- [ 14.031609] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
- [ 14.038564] mt7621-pci 1e140000.pcie: PCIE0 enabled
- [ 14.043439] mt7621-pci 1e140000.pcie: PCIE1 enabled
- [ 14.048319] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
- [ 14.057787] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
- [ 14.064163] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
- [ 14.071034] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
- [ 14.077901] pci_bus 0000:00: root bus resource [bus 00-ff]
- [ 14.083427] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
- [ 14.089461] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
- [ 14.095730] pci 0000:00:00.0: reg 0x14: [mem 0x60600000-0x6060ffff]
- [ 14.102058] pci 0000:00:00.0: supports D1
- [ 14.106070] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
- [ 14.112196] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
- [ 14.118236] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
- [ 14.124506] pci 0000:00:01.0: reg 0x14: [mem 0x60610000-0x6061ffff]
- [ 14.130829] pci 0000:00:01.0: supports D1
- [ 14.134843] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
- [ 14.142135] pci 0000:01:00.0: [14c3:7916] type 00 class 0x000280
- [ 14.148232] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
- [ 14.155463] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
- [ 14.162692] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
- [ 14.170026] pci 0000:01:00.0: supports D1 D2
- [ 14.174297] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
- [ 14.180944] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
- [ 14.196074] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
- [ 14.201319] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
- [ 14.207410] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
- [ 14.214190] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref]
- [ 14.221410] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
- [ 14.228242] pci 0000:02:00.0: [14c3:7915] type 00 class 0x000280
- [ 14.234314] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
- [ 14.241562] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
- [ 14.248792] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
- [ 14.256126] pci 0000:02:00.0: supports D1 D2
- [ 14.260398] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
- [ 14.267047] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
- [ 14.282179] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
- [ 14.287426] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
- [ 14.293515] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff]
- [ 14.300298] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref]
- [ 14.307517] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
- [ 14.314167] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
- [ 14.320776] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
- [ 14.327734] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
- [ 14.334351] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
- [ 14.341303] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
- [ 14.348087] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref]
- [ 14.355304] pci 0000:00:01.0: BAR 8: assigned [mem 0x60300000-0x603fffff]
- [ 14.362086] pci 0000:00:01.0: BAR 9: assigned [mem 0x60400000-0x605fffff pref]
- [ 14.369303] pci 0000:00:00.0: BAR 1: assigned [mem 0x60600000-0x6060ffff]
- [ 14.376093] pci 0000:00:01.0: BAR 1: assigned [mem 0x60610000-0x6061ffff]
- [ 14.382881] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
- [ 14.389663] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
- [ 14.396455] pci 0000:01:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref]
- [ 14.404203] pci 0000:01:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref]
- [ 14.411960] pci 0000:01:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref]
- [ 14.419706] pci 0000:00:00.0: PCI bridge to [bus 01]
- [ 14.424670] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
- [ 14.431454] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
- [ 14.438233] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref]
- [ 14.445457] pci 0000:02:00.0: BAR 0: assigned [mem 0x60400000-0x604fffff 64bit pref]
- [ 14.453206] pci 0000:02:00.0: BAR 2: assigned [mem 0x60500000-0x60503fff 64bit pref]
- [ 14.460955] pci 0000:02:00.0: BAR 4: assigned [mem 0x60504000-0x60504fff 64bit pref]
- [ 14.468699] pci 0000:00:01.0: PCI bridge to [bus 02]
- [ 14.473663] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
- [ 14.480445] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff]
- [ 14.487226] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref]
- [ 14.495210] hctosys: unable to open rtc device (rtc0)
- [ 14.527165] Freeing unused kernel memory: 7308K
- [ 14.531743] This architecture does not have kernel memory protection.
- [ 14.538170] Run /init as init process
- [ 14.542420] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
- [ 15.209208] init: Console is alive
- [ 15.213203] init: - watchdog -
- [ 15.233551] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 15.250101] usbcore: registered new interface driver usbfs
- [ 15.255769] usbcore: registered new interface driver hub
- [ 15.261210] usbcore: registered new device driver usb
- [ 15.269591] Button Hotplug driver version 0.4.1
- [ 15.285504] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator
- [ 15.294251] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
- [ 15.303232] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
- [ 15.308573] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
- [ 15.322542] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010
- [ 15.331769] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
- [ 15.338913] hub 1-0:1.0: USB hub found
- [ 15.342836] hub 1-0:1.0: 2 ports detected
- [ 15.347576] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
- [ 15.352931] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
- [ 15.360418] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
- [ 15.366966] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
- [ 15.375982] hub 2-0:1.0: USB hub found
- [ 15.379859] hub 2-0:1.0: 1 port detected
- [ 15.389091] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 15.398725] init: - preinit -
- [ 15.533776] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
- [ 15.542100] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
- [ 15.550587] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
- [ 15.629663] random: jshn: uninitialized urandom read (4 bytes read)
- [ 15.695374] random: jshn: uninitialized urandom read (4 bytes read)
- [ 15.735757] random: jshn: uninitialized urandom read (4 bytes read)
- [ 15.979670] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
- [ 15.986719] 8021q: adding VLAN 0 to HW filter on device lan1
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 20.128177] procd: - early -
- [ 20.131186] procd: - watchdog -
- [ 20.686520] procd: - watchdog -
- [ 20.690085] procd: - ubus -
- [ 20.699802] urandom_read: 6 callbacks suppressed
- [ 20.699814] random: ubusd: uninitialized urandom read (4 bytes read)
- [ 20.749984] procd: - init -
- Please press Enter to activate this console.
- [ 21.081228] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 21.161851] i2c /dev entries driver
- [ 21.178407] hidraw: raw HID events driver (C) Jiri Kosina
- [ 21.186124] Loading modules backported from Linux version v5.10.68-0-g4d8524048a35
- [ 21.193717] Backport generated by backports.git v5.10.68-1-0-ga4f9ba32
- [ 21.207401] lib80211: common routines for IEEE802.11 drivers
- [ 21.225508] urngd: v1.0.2 started.
- [ 21.227101] xt_time: kernel timezone is -0000
- [ 21.285044] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=23
- [ 21.290546] pci 0000:00:00.0: enabling device (0006 -> 0007)
- [ 21.296220] mt7915e_hif 0000:01:00.0: enabling device (0000 -> 0002)
- [ 21.303079] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=24
- [ 21.308546] pci 0000:00:01.0: enabling device (0006 -> 0007)
- [ 21.314217] mt7915e 0000:02:00.0: enabling device (0000 -> 0002)
- [ 21.340226] mt7915e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20201105222230a
- [ 21.340226]
- [ 21.366224] random: crng init done
- [ 21.367939] mt7915e 0000:02:00.0: WM Firmware Version: ____000000, Build Time: 20201105222304
- [ 21.408206] mt7915e 0000:02:00.0: WA Firmware Version: DEV_000000, Build Time: 20201105222323
- [ 21.557076] PPP generic driver version 2.4.2
- [ 21.563193] NET: Registered protocol family 24
- [ 21.579072] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 39.584700] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
- [ 39.602697] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
- [ 39.610917] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
- [ 39.614305] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
- [ 39.626711] 8021q: adding VLAN 0 to HW filter on device lan1
- [ 39.636019] br-lan: port 1(lan1) entered blocking state
- [ 39.641369] br-lan: port 1(lan1) entered disabled state
- [ 39.648152] device lan1 entered promiscuous mode
- [ 39.652922] device eth0 entered promiscuous mode
- [ 39.661378] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
- [ 39.685120] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
- [ 39.693831] 8021q: adding VLAN 0 to HW filter on device lan2
- [ 39.703105] br-lan: port 2(lan2) entered blocking state
- [ 39.708404] br-lan: port 2(lan2) entered disabled state
- [ 39.715099] device lan2 entered promiscuous mode
- == ETH PLUGGED IN ==
- [ 62.234868] mt7530 mdio-bus:1f lan2: Link is Up - 1Gbps/Full - flow control rx/tx
- [ 62.242414] br-lan: port 2(lan2) entered blocking state
- [ 62.247650] br-lan: port 2(lan2) entered forwarding state
- [ 62.254008] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
- [ 63.162880] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control off
- [ 63.170245] br-lan: port 1(lan1) entered blocking state
- [ 63.175487] br-lan: port 1(lan1) entered forwarding state
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement