smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.1.79-Unraid] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUH721010AL4200
Revision:             A2R0
Compliance:           SPC-4
User Capacity:        9,931,038,130,176 bytes [9.93 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca2567b8c20
Serial number:        7GJ5YATK
Device type:          disk
Transport protocol:   SAS (SPL-4)
Local Time is:        Fri Apr  5 08:28:34 2024 CDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Disabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     40 C
Drive Trip Temperature:        85 C

Manufactured in week 04 of year 2017
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  113
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  990
Elements in grown defect list: 0

Vendor (Seagate Cache) information
  Blocks sent to initiator = 4309867544182784

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0       55         0        55   33197048     443267.350           0
write:         0        0         0         0      12720      44730.684           0
verify:        0        0         0         0     131975          0.000           0

Non-medium error count:        0

SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -    8434                 - [-   -    -]

Long (extended) Self-test duration: 74640 seconds [20.7 hours]

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 21259:14 [1275554 minutes]
    Number of background scans performed: 136,  scan progress: 0.00%
    Number of background medium scans performed: 136

General statistics and performance log page:
  General access statistics and performance:
    Number of read commands: 2454203680
    Number of write commands: 256888124
    number of logical blocks received: 10920577067
    number of logical blocks transmitted: 108219567969
    read command processing intervals: 0
    write command processing intervals: 0
    weighted number of read commands plus write commands: 0
    weighted read command processing plus write command processing: 0
  Idle time:
    Idle time intervals: 1396313066
      in seconds: 69815653.300
      in hours: 19393.237

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 2
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: hard reset
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca2567b8c21
    attached SAS address = 0x50030480186bdfff
    attached phy identifier = 10
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization count = 0
    Phy reset problem count = 0
relative target port id = 2
  generation code = 2
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: power on
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000cca2567b8c22
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization count = 0
    Phy reset problem count = 0