SHARE
TWEET

Untitled

a guest Nov 19th, 2012 190 Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. U-Boot 2009.08 (Jul 05 2012 - 15:37:27)
  2.  
  3. CPU:   Freescale i.MX 6 family 0.0V at 792 MHz
  4. Temperature:   can't get valid data!
  5. mx6q pll1: 792MHz
  6. mx6q pll2: 528MHz
  7. mx6q pll3: 480MHz
  8. mx6q pll8: 50MHz
  9. ipg clock     : 66000000Hz
  10. ipg per clock : 66000000Hz
  11. uart clock    : 80000000Hz
  12. cspi clock    : 60000000Hz
  13. ahb clock     : 132000000Hz
  14. axi clock   : 264000000Hz
  15. emi_slow clock: 29333333Hz
  16. ddr clock     : 528000000Hz
  17. usdhc1 clock  : 200000000Hz
  18. usdhc2 clock  : 200000000Hz
  19. usdhc3 clock  : 200000000Hz
  20. usdhc4 clock  : 200000000Hz
  21. nfc clock     : 24000000Hz
  22. Board: MX6Q-SABRELITE:[ POR]
  23. Boot Device: I2C
  24. I2C:   ready
  25. DRAM:   1 GB
  26. MMC:   FSL_USDHC: 0,FSL_USDHC: 1
  27. JEDEC ID: 0xbf:0x25:0x41
  28. Reading SPI NOR flash 0xc0000 [0x2000 bytes] -> ram 0x276009b8
  29. SUCCESS
  30.  
  31. In:    serial
  32. Out:   serial
  33. Err:   serial
  34. Net:   got MAC address from IIM: 00:19:b8:00:fd:4e
  35. FEC0 [PRIME]
  36. Warning: FEC0 MAC addresses don't match:
  37. Address in SROM is         00:19:b8:00:fd:4e
  38. Address in environment is  00:01:02:03:04:05
  39.  
  40. Hit any key to stop autoboot:  0
  41. mmc0 is current device
  42. reading /6q_bootscript
  43.  
  44. ** Unable to read "/6q_bootscript" from mmc 0:1 **
  45. Loading file "/6q_bootscript" from mmc device 0:1 (xxa1)
  46. 583 bytes read
  47. ## Executing script at 10008000
  48. Loading file "/boot/uImage" from mmc device 0:1 (xxa1)
  49. 3605880 bytes read
  50. ## Booting kernel from Legacy Image at 10800000 ...
  51.    Image Name:   Linux-3.0.15-01386-g5c661b1
  52.    Image Type:   ARM Linux Kernel Image (uncompressed)
  53.    Data Size:    3605816 Bytes =  3.4 MB
  54.    Load Address: 10008000
  55.    Entry Point:  10008000
  56.    Verifying Checksum ... OK
  57.    Loading Kernel Image ... OK
  58. OK
  59.  
  60. Starting kernel ...
  61.  
  62. Uncompressing Linux... done, booting the kernel.
  63. Linux version 3.0.15-01386-g5c661b1 (ericn@ericsony) (gcc version 4.4.4 (4.4.4_09.06.2010) ) #64 SMP PREEMPT Tue Jun 26 11:16:43 MST 2012
  64. CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
  65. CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
  66. Machine: Freescale i.MX 6Quad Sabre-Lite Board
  67. Memory policy: ECC disabled, Data cache writealloc
  68. PERCPU: Embedded 7 pages/cpu @8c008000 s5440 r8192 d15040 u32768
  69. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 227328
  70. Kernel command line: console=ttymxc1,115200 vmalloc=400M root=/dev/mmcblk0p1 rootwait fixrtc consoleblank=0 video=mxcfb0:dev=hdmi,1280x720M@60,if=RGB24 video=mxcfb1:dev=lcd,800x480M@60,if=RGB666 fbmem=28M,10M
  71. PID hash table entries: 4096 (order: 2, 16384 bytes)
  72. Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  73. Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  74. Memory: 640MB 256MB = 896MB total
  75. Memory: 897764k/897764k available, 150812k reserved, 0K highmem
  76. Virtual kernel memory layout:
  77.     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
  78.     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
  79.     DMA     : 0xf4600000 - 0xffe00000   ( 184 MB)
  80.     vmalloc : 0xc0800000 - 0xf2000000   ( 792 MB)
  81.     lowmem  : 0x80000000 - 0xc0000000   (1024 MB)
  82.     pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
  83.     modules : 0x7f000000 - 0x7fe00000   (  14 MB)
  84.       .init : 0x80008000 - 0x80035000   ( 180 kB)
  85.       .text : 0x80035000 - 0x809eba64   (9947 kB)
  86.       .data : 0x809ec000 - 0x80a2f0a0   ( 269 kB)
  87.        .bss : 0x80a2f0c4 - 0x80a59e78   ( 172 kB)
  88. SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
  89. Preemptible hierarchical RCU implementation.
  90. NR_IRQS:496
  91. MXC GPIO hardware
  92. sched_clock: 32 bits at 6MHz, resolution 166ns, wraps every 715827ms
  93. MXC_Early serial console at MMIO 0x21e8000 (options '115200')
  94. bootconsole [ttymxc1] enabled
  95. Console: colour dummy device 80x30
  96. Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
  97. pid_max: default: 32768 minimum: 301
  98. Mount-cache hash table entries: 512
  99. CPU: Testing write buffer coherency: ok
  100. hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
  101. CPU1: Booted secondary processor
  102. CPU2: Booted secondary processor
  103. CPU3: Booted secondary processor
  104. Brought up 4 CPUs
  105. SMP: Total of 4 processors activated (6324.22 BogoMIPS).
  106. print_constraints: dummy:
  107. NET: Registered protocol family 16
  108. print_constraints: vddpu: 725 <--> 1300 mV at 1100 mV fast normal
  109. print_constraints: vddcore: 725 <--> 1300 mV at 1100 mV fast normal
  110. print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal
  111. print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal
  112. print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal
  113. print_constraints: vdd3p0: 2800 <--> 3150 mV at 3000 mV fast normal
  114. ------------ Board type Sabre Lite
  115. hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
  116. hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
  117. hw-breakpoint: maximum watchpoint size is 4 bytes.
  118. L310 cache controller enabled
  119. l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x02070000, Cache size: 1048576 B
  120. IMX usb wakeup probe
  121. IMX usb wakeup probe
  122. bio: create slab <bio-0> at 0
  123. print_constraints: VDDA: 2500 mV
  124. print_constraints: VDDIO: 3300 mV
  125. machine_constraints_voltage: VDDD: unsupportable voltage constraints
  126. reg-fixed-voltage reg-fixed-voltage.2: Failed to register regulator: -22
  127. reg-fixed-voltage: probe of reg-fixed-voltage.2 failed with error -22
  128. print_constraints: vmmc: 3300 mV
  129. SCSI subsystem initialized
  130. spi_imx imx6q-ecspi.0: probed
  131. usbcore: registered new interface driver usbfs
  132. usbcore: registered new interface driver hub
  133. usbcore: registered new device driver usb
  134. Freescale USB OTG Driver loaded, $Revision: 1.55 $
  135. add wake up source irq 75
  136. imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
  137. imx-ipuv3 imx-ipuv3.1: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
  138. mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 driver probed
  139. mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 dphy version is 0x3130302a
  140. MIPI CSI2 driver module loaded
  141. Advanced Linux Sound Architecture Driver Version 1.0.24.
  142. cfg80211: Calling CRDA to update world regulatory domain
  143. i2c-core: driver [max17135] using legacy suspend method
  144. i2c-core: driver [max17135] using legacy resume method
  145. Switching to clocksource mxc_timer1
  146. Switched to NOHz mode on CPU #0
  147. Switched to NOHz mode on CPU #2
  148. Switched to NOHz mode on CPU #1
  149. Switched to NOHz mode on CPU #3
  150. NET: Registered protocol family 2
  151. IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
  152. TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
  153. TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
  154. TCP: Hash tables configured (established 131072 bind 65536)
  155. TCP reno registered
  156. UDP hash table entries: 512 (order: 2, 16384 bytes)
  157. UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  158. NET: Registered protocol family 1
  159. RPC: Registered named UNIX socket transport module.
  160. RPC: Registered udp transport module.
  161. RPC: Registered tcp transport module.
  162. RPC: Registered tcp NFSv4.1 backchannel transport module.
  163. Static Power Management for Freescale i.MX6
  164. cpaddr = c0884000 suspend_iram_base=c0932000
  165. PM driver module loaded
  166. i.MXC CPU frequency driver
  167. JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
  168. msgmni has been set to 1753
  169. io scheduler noop registered
  170. io scheduler deadline registered
  171. io scheduler cfq registered (default)
  172. MIPI DSI driver module loaded
  173. mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver hdmi
  174. mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0xa:0xa0:0xc1
  175. fbcvt: 1280x720@60: CVT Name - .921M9
  176. imx-ipuv3 imx-ipuv3.0: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
  177. Console: switching to colour frame buffer device 160x45
  178. mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver lcd
  179. fbcvt: 800x480@60: CVT Name - .384M9
  180. imx-ipuv3 imx-ipuv3.0: ext di clk already in use, go back to internal clk
  181. mxc_sdc_fb mxc_sdc_fb.2: register mxc display driver ldb
  182. _regulator_get: get() with no identifier
  183. mxc_sdc_fb mxc_sdc_fb.3: register mxc display driver ldb
  184. fbcvt: 1280x720@60: CVT Name - .921M9
  185. imx-ipuv3 imx-ipuv3.0: WARNING: adapt panel end blank lines
  186. imx-sdma imx-sdma: loaded firmware 1.1
  187. imx-sdma imx-sdma: initialized
  188. Serial: IMX driver
  189. imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
  190. imx-uart.1: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX
  191. old_ufcr=a81 new_ufcr=b01, old_ucr2=4027 new_ucr2=4027, old_ubir=f num=1f7, old_ubmr=15b denom=c34
  192. clk=80000000 div=7 num=504 denom=3125 baud=115200
  193. console [ttymxc1] enabled, bootconsole disabled
  194. console [ttymxc1] enabled, bootconsole disabled
  195. loop: module loaded
  196. Can't recover from RESET HBA!
  197. No sata disk.
  198. m25p80 spi0.0: sst25vf016b (2048 Kbytes)
  199. Creating 2 MTD partitions on "m25p80":
  200. 0x000000000000-0x000000040000 : "bootloader"
  201. 0x000000040000-0x000000200000 : "kernel"
  202. vcan: Virtual CAN interface driver
  203. CAN device driver interface
  204. flexcan netdevice driver
  205. flexcan imx6q-flexcan.0: device registered (reg_base=c09a8000, irq=142)
  206. FEC Ethernet Driver
  207. fec_enet_mii_bus: probed
  208. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  209. fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
  210. fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
  211. fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000
  212. fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
  213. usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
  214. usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  215. usb usb1: Product: Freescale On-Chip EHCI Host Controller
  216. usb usb1: Manufacturer: Linux 3.0.15-01386-g5c661b1 ehci_hcd
  217. usb usb1: SerialNumber: fsl-ehci.0
  218. hub 1-0:1.0: USB hub found
  219. hub 1-0:1.0: 1 port detected
  220. add wake up source irq 72
  221. fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
  222. fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
  223. fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200
  224. fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
  225. usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
  226. usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  227. usb usb2: Product: Freescale On-Chip EHCI Host Controller
  228. usb usb2: Manufacturer: Linux 3.0.15-01386-g5c661b1 ehci_hcd
  229. usb usb2: SerialNumber: fsl-ehci.1
  230. hub 2-0:1.0: USB hub found
  231. hub 2-0:1.0: 1 port detected
  232. Initializing USB Mass Storage driver...
  233. usbcore: registered new interface driver usb-storage
  234. USB Mass Storage support registered.
  235. ARC USBOTG Device Controller driver (1 August 2005)
  236. mousedev: PS/2 mouse device common for all mice
  237. input: gpio-keys as /devices/platform/gpio-keys/input/input0
  238. tsc2004_prepare_for_reading: write_cmd -5
  239. tsc2004: probe of 2-0048 failed with error -5
  240. egalax_ts 2-0004: egalax_ts: failed to read firmware version
  241. egalax_ts: probe of 2-0004 failed with error -5
  242. i2c-core: driver [isl29023] using legacy suspend method
  243. i2c-core: driver [isl29023] using legacy resume method
  244. snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc0
  245. i2c /dev entries driver
  246. Linux video capture interface: v2.00
  247. mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16
  248. mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17
  249. mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video18
  250. mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video19
  251. mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video20
  252. mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video21
  253. i2c-core: driver [mag3110] using legacy suspend method
  254. i2c-core: driver [mag3110] using legacy resume method
  255. imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
  256. sdhci: Secure Digital Host Controller Interface driver
  257. sdhci: Copyright(c) Pierre Ossman
  258. mmc0: Unknown controller version (3). You may experience problems.
  259. mmc0: SDHCI controller on platform [sdhci-esdhc-imx.2] using ADMA
  260. sdhci sdhci-esdhc-imx.3: no write-protect pin available!
  261. mmc1: Unknown controller version (3). You may experience problems.
  262. mmc1: SDHCI controller on platform [sdhci-esdhc-imx.3] using ADMA
  263. mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
  264. VPU initialized
  265. mxc_asrc registered
  266. Anatop Thermal registered as thermal_zone0
  267. usb 2-1: new high speed USB device number 2 using fsl-ehci
  268. anatop_thermal_probe: default cooling device is cpufreq!
  269. usbcore: registered new interface driver usbhid
  270. usbhid: USB HID core driver
  271. mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio
  272. sgtl5000 0-000a: Failed to get supply 'VDDD': -19
  273. print_constraints: 0-000a: 850 <--> 1600 mV at 1200 mV normal
  274. sgtl5000 0-000a: sgtl5000 revision 17
  275. mmc0: new SDHC card at address 0001
  276. mmcblk0: mmc0:0001 00000 7.46 GiB
  277.  mmcblk0: p1
  278. asoc: sgtl5000 <-> imx-ssi.1 mapping ok
  279. asoc: mxc-hdmi-soc <-> imx-hdmi-soc-dai.0 mapping ok
  280. ALSA device list:
  281.   #0: sgtl5000-audio
  282.   #1: imx-hdmi-soc
  283. NET: Registered protocol family 26
  284. TCP cubic registered
  285. NET: Registered protocol family 17
  286. can: controller area network core (rev 20090105 abi 8)
  287. NET: Registered protocol family 29
  288. can: raw protocol (rev 20090105)
  289. can: broadcast manager protocol (rev 20090105 t)
  290. lib80211: common routines for IEEE802.11 drivers
  291. VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
  292. Bus freq driver module loaded
  293. mxc_dvfs_core_probe
  294. DVFS driver module loaded
  295. snvs_rtc snvs_rtc.0: setting system clock to 1970-01-01 00:00:00 UTC (0)
  296. EXT3-fs: barriers not enabled
  297. usb 2-1: New USB device found, idVendor=0424, idProduct=2513
  298. usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
  299. hub 2-1:1.0: USB hub found
  300. hub 2-1:1.0: 3 ports detected
  301. kjournald starting.  Commit interval 5 seconds
  302. EXT3-fs (mmcblk0p1): using internal journal
  303. EXT3-fs (mmcblk0p1): recovery complete
  304. EXT3-fs (mmcblk0p1): mounted filesystem with writeback data mode
  305. VFS: Mounted root (ext3 filesystem) on device 179:1.
  306. Freeing init memory: 180K
  307. Thermal: fuse data 0x58e5523a
  308. anatop_thermal_counting_ratio: raw25c=1422 raw_hot=1362 hot_temp=58
  309. usb 2-1.1: new low speed USB device number 3 using fsl-ehci
  310. usb 2-1.1: New USB device found, idVendor=09da, idProduct=0260
  311. usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
  312. usb 2-1.1: Product: USB Keyboard
  313. usb 2-1.1: Manufacturer:  
  314. input:   USB Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.1/2-1.1:1.0/input/input1
  315. generic-usb 0003:09DA:0260.0001: input,hidraw0: USB HID v1.10 Keyboard [  USB Keyboard] on usb-fsl-ehci.1-1.1/input0
  316. input:   USB Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.1/2-1.1:1.1/input/input2
  317. generic-usb 0003:09DA:0260.0002: input,hidraw1: USB HID v1.10 Device [  USB Keyboard] on usb-fsl-ehci.1-1.1/input1
  318. usb 2-1.1: USB disconnect, device number 3
RAW Paste Data
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy. OK, I Understand
 
Top