Guest User

Untitled

a guest
Jun 8th, 2020
472
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. U-Boot SPL 2020.04-00006-ga4741b534d-dirty (Jun 04 2020 - 12:52:55 +0300)
  2. Model: STM32MP1 OLinuXino
  3. RAM: DDR3-1066/888 bin G 2x4Gb 533MHz v1.45
  4. Init AXP209 PMIC
  5. ---------0------------
  6. Trying to boot from MMC1
  7.  
  8.  
  9. U-Boot 2020.04-00006-ga4741b534d-dirty (Jun 04 2020 - 12:52:55 +0300)
  10.  
  11. CPU: STM32MP157CAA Rev.B
  12. Model: STM32MP1 OLinuXino
  13. Board: stm32mp1 in basic mode (olimex,stm32mp1-olinuxino)
  14. DRAM: 1 GiB
  15. Clocks:
  16. - MPU : 650 MHz
  17. - MCU : 208.878 MHz
  18. - AXI : 266.500 MHz
  19. - PER : 24 MHz
  20. - DDR : 533 MHz
  21. NAND: 0 MiB
  22. MMC: STM32 SDMMC2: 0
  23. Loading Environment from EXT4... OK
  24. In: serial
  25. Out: serial
  26. Err: serial
  27. invalid MAC address in OTP 00:00:00:00:00:00
  28. Net:
  29. Error: ethernet@5800a000 address not set.
  30. No ethernet found.
  31.  
  32. Hit any key to stop autoboot: 0
  33. Boot over mmc0!
  34. switch to partitions #0, OK
  35. mmc0 is current device
  36. Scanning mmc 0:4...
  37. Found /extlinux/extlinux.conf
  38. Retrieving file: /extlinux/extlinux.conf
  39. 235 bytes read in 18 ms (12.7 KiB/s)
  40. Retrieving file: /splash.bmp
  41. 385078 bytes read in 34 ms (10.8 MiB/s)
  42. 1: cubemx-sdcard
  43. Retrieving file: /uImage
  44. 6656576 bytes read in 301 ms (21.1 MiB/s)
  45. append: root=/dev/mmcblk1p6 rootwait rw console=ttySTM0,115200
  46. Retrieving file: /stm32mp157a-visionsom-mx.dtb
  47. 71269 bytes read in 21 ms (3.2 MiB/s)
  48. ## Booting kernel from Legacy Image at c2000000 ...
  49. Image Name: Linux-4.19.94
  50. Created: 2020-01-09 9:19:10 UTC
  51. Image Type: ARM Linux Kernel Image (uncompressed)
  52. Data Size: 6656512 Bytes = 6.3 MiB
  53. Load Address: c2000040
  54. Entry Point: c2000040
  55. Verifying Checksum ... OK
  56. ## Flattened Device Tree blob at c4000000
  57. Booting using the fdt blob at 0xc4000000
  58. XIP Kernel Image
  59. Loading Device Tree to cffeb000, end cffff664 ... OK
  60. unrecognized JEDEC id bytes: 00, 00, 00
  61.  
  62. Starting kernel ...
  63.  
  64. [ 0.000000] Booting Linux on physical CPU 0x0
  65. [ 0.000000] Linux version 4.19.94 (oe-user@oe-host) (gcc version 8.2.0 (GCC)) #1 SMP PREEMPT Thu Jan 9 09:19:10 UTC 2020
  66. [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
  67. [ 0.000000] CPU: div instructions available: patching division code
  68. [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  69. [ 0.000000] OF: fdt: Machine model: STMicroelectronics custom STM32CubeMX board
  70. [ 0.000000] Memory policy: Data cache writealloc
  71. [ 0.000000] efi: Getting EFI parameters from FDT:
  72. [ 0.000000] efi: UEFI not found.
  73. [ 0.000000] cma: Reserved 128 MiB at 0xf5000000
  74. [ 0.000000] psci: probing for conduit method from DT.
  75. [ 0.000000] psci: PSCIv1.0 detected in firmware.
  76. [ 0.000000] psci: Using standard PSCI v0.2 function IDs
  77. [ 0.000000] psci: Trusted OS migration not required
  78. [ 0.000000] psci: SMC Calling Convention v1.0
  79. [ 0.000000] random: get_random_bytes called from start_kernel+0x9c/0x4b0 with crng_init=0
  80. [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536
  81. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 231744
  82. [ 0.000000] Kernel command line: root=/dev/mmcblk1p6 rootwait rw console=ttySTM0,115200
  83. [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  84. [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  85. [ 0.000000] Memory: 776968K/933888K available (10240K kernel code, 821K rwdata, 2900K rodata, 1024K init, 208K bss, 25848K reserved, 131072K cma-reserved, 81920K highmem)
  86. [ 0.000000] Virtual kernel memory layout:
  87. [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  88. [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
  89. [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
  90. [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
  91. [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  92. [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
  93. [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (11232 kB)
  94. [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB)
  95. [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 822 kB)
  96. [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 209 kB)
  97. [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  98. [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
  99. [ 0.000000] rcu: RCU event tracing is enabled.
  100. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
  101. [ 0.000000] Tasks RCU enabled.
  102. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
  103. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
  104. [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).
  105. [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
  106. [ 0.000010] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
  107. [ 0.000028] Switching to timer-based delay loop, resolution 41ns
  108. [ 0.002030] Console: colour dummy device 80x30
  109. [ 0.002087] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
  110. [ 0.002109] pid_max: default: 32768 minimum: 301
  111. [ 0.002330] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
  112. [ 0.002356] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
  113. [ 0.003358] CPU: Testing write buffer coherency: ok
  114. [ 0.003851] /cpus/cpu@0 missing clock-frequency property
  115. [ 0.003884] /cpus/cpu@1 missing clock-frequency property
  116. [ 0.003903] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
  117. [ 0.059755] Setting up static identity map for 0xc0100000 - 0xc0100060
  118. [ 0.079750] rcu: Hierarchical SRCU implementation.
  119. [ 0.103874] EFI services will not be available.
  120. [ 0.119891] smp: Bringing up secondary CPUs ...
  121. [ 0.200257] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
  122. [ 0.200481] smp: Brought up 1 node, 2 CPUs
  123. [ 0.200508] SMP: Total of 2 processors activated (96.00 BogoMIPS).
  124. [ 0.200519] CPU: All CPU(s) started in SVC mode.
  125. [ 0.201656] devtmpfs: initialized
  126. [ 0.228860] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
  127. [ 0.229384] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  128. [ 0.229418] futex hash table entries: 512 (order: 3, 32768 bytes)
  129. [ 0.235504] pinctrl core: initialized pinctrl subsystem
  130. [ 0.237092] DMI not present or invalid.
  131. [ 0.237683] NET: Registered protocol family 16
  132. [ 0.240883] DMA: preallocated 256 KiB pool for atomic coherent allocations
  133. [ 0.243434] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
  134. [ 0.243456] hw-breakpoint: maximum watchpoint size is 8 bytes.
  135. [ 0.243750] Serial: AMBA PL011 UART driver
  136. [ 0.246048] stm32-pm-domain pm_domain: domain core-ret-power-domain registered
  137. [ 0.246088] stm32-pm-domain pm_domain: subdomain core-power-domain registered
  138. [ 0.246104] stm32-pm-domain pm_domain: domains probed
  139. [ 0.252470] /soc/interrupt-controller@5000d000: bank0
  140. [ 0.252492] /soc/interrupt-controller@5000d000: bank1
  141. [ 0.252505] /soc/interrupt-controller@5000d000: bank2
  142. [ 0.260704] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOA bank added
  143. [ 0.261147] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOB bank added
  144. [ 0.261551] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOC bank added
  145. [ 0.261936] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOD bank added
  146. [ 0.262316] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOE bank added
  147. [ 0.262696] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOF bank added
  148. [ 0.263083] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOG bank added
  149. [ 0.263478] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOH bank added
  150. [ 0.263768] stm32mp157-pinctrl soc:pin-controller@50002000: Pinctrl STM32 initialized
  151. [ 0.264131] stm32mp157-pinctrl soc:pin-controller-z@54004000: No package detected, use default one
  152. [ 0.264323] stm32mp157-pinctrl soc:pin-controller-z@54004000: at least one GPIO bank is required
  153. [ 0.264508] stm32mp157-pinctrl: probe of soc:pin-controller-z@54004000 failed with error -22
  154. [ 0.284694] stm32-mdma 58000000.dma: STM32 MDMA driver registered
  155. [ 0.285591] regulator_vdd: mapping for mode 0 not defined
  156. [ 0.287113] REG11: supplied by vdd
  157. [ 0.287517] REG18: supplied by vdd
  158. [ 0.287851] USB33: supplied by regulator-dummy
  159. [ 0.290939] SCSI subsystem initialized
  160. [ 0.291721] usbcore: registered new interface driver usbfs
  161. [ 0.291804] usbcore: registered new interface driver hub
  162. [ 0.291946] usbcore: registered new device driver usb
  163. [ 0.292276] pps_core: LinuxPPS API ver. 1 registered
  164. [ 0.292290] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  165. [ 0.292324] PTP clock support registered
  166. [ 0.292593] EDAC MC: Ver: 3.0.0
  167. [ 0.293465] Advanced Linux Sound Architecture Driver Initialized.
  168. [ 0.295127] clocksource: Switched to clocksource arch_sys_counter
  169. [ 0.388236] NET: Registered protocol family 2
  170. [ 0.389421] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
  171. [ 0.389474] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
  172. [ 0.389585] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
  173. [ 0.389764] TCP: Hash tables configured (established 8192 bind 8192)
  174. [ 0.389933] UDP hash table entries: 512 (order: 2, 16384 bytes)
  175. [ 0.390001] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  176. [ 0.390332] NET: Registered protocol family 1
  177. [ 0.411312] RPC: Registered named UNIX socket transport module.
  178. [ 0.411334] RPC: Registered udp transport module.
  179. [ 0.411345] RPC: Registered tcp transport module.
  180. [ 0.411356] RPC: Registered tcp NFSv4.1 backchannel transport module.
  181. [ 0.412482] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
  182. [ 0.414657] Initialise system trusted keyrings
  183. [ 0.415005] workingset: timestamp_bits=14 max_order=18 bucket_order=4
  184. [ 0.426904] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  185. [ 0.428049] NFS: Registering the id_resolver key type
  186. [ 0.428096] Key type id_resolver registered
  187. [ 0.428110] Key type id_legacy registered
  188. [ 0.428341] ntfs: driver 2.1.32 [Flags: R/O].
  189. [ 0.428868] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
  190. [ 0.429710] fuse init (API version 7.27)
  191. [ 0.433596] NET: Registered protocol family 38
  192. [ 0.433627] Key type asymmetric registered
  193. [ 0.433641] Asymmetric key parser 'x509' registered
  194. [ 0.433736] bounce: pool size: 64 pages
  195. [ 0.433817] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
  196. [ 0.433834] io scheduler noop registered
  197. [ 0.433846] io scheduler deadline registered
  198. [ 0.434109] io scheduler cfq registered (default)
  199. [ 0.434126] io scheduler mq-deadline registered
  200. [ 0.434138] io scheduler kyber registered
  201. [ 0.435502] stm32-usbphyc 5a006000.usbphyc: Linked as a consumer to regulator.3
  202. [ 0.435647] stm32-usbphyc 5a006000.usbphyc: Linked as a consumer to regulator.4
  203. [ 0.435748] stm32-usbphyc 5a006000.usbphyc: Linked as a consumer to regulator.2
  204. [ 0.436371] stm32-usbphyc 5a006000.usbphyc: registered rev:1.0
  205. [ 0.439368] stm32-dma 48000000.dma: no dma pool: can't use MDMA: 0
  206. [ 0.441101] stm32-dma 48000000.dma: STM32 DMA driver registered
  207. [ 0.441297] stm32-dma 48001000.dma: no dma pool: can't use MDMA: 0
  208. [ 0.442898] stm32-dma 48001000.dma: STM32 DMA driver registered
  209. [ 0.524299] STM32 USART driver initialized
  210. [ 0.525769] stm32-usart 40010000.serial: Linked as a consumer to 48000000.dma
  211. [ 0.526049] 40010000.serial: ttySTM0 at MMIO 0x40010000 (irq = 23, base_baud = 4000000) is a stm32-usart
  212. [ 1.403747] console [ttySTM0] enabled
  213. [ 1.409323] stm32-usart 40018000.serial: Linked as a consumer to 48000000.dma
  214. [ 1.415295] 40018000.serial: ttySTM1 at MMIO 0x40018000 (irq = 24, base_baud = 4000000) is a stm32-usart
  215. [ 1.424788] serial serial0: tty port ttySTM1 registered
  216. [ 1.429876] genirq: irq_chip stm32-exti-h did not update eff. affinity mask of irq 63
  217. [ 1.438878] stm32-usart 40019000.serial: Linked as a consumer to 48000000.dma
  218. [ 1.444955] 40019000.serial: ttySTM2 at MMIO 0x40019000 (irq = 25, base_baud = 4000000) is a stm32-usart
  219. [ 1.459631] panel-simple panel: panel supply power not found, using dummy regulator
  220. [ 1.466089] panel-simple panel: Linked as a consumer to regulator.0
  221. [ 1.488082] brd: module loaded
  222. [ 1.502688] loop: module loaded
  223. [ 1.510772] libphy: Fixed MDIO Bus: probed
  224. [ 1.515354] CAN device driver interface
  225. [ 1.519835] stm32-dwmac 5800a000.ethernet: PTP uses main clock
  226. [ 1.524232] stm32-dwmac 5800a000.ethernet: no reset control found
  227. [ 1.531029] stm32-dwmac 5800a000.ethernet: User ID: 0x40, Synopsys ID: 0x42
  228. [ 1.537398] stm32-dwmac 5800a000.ethernet: DWMAC4/5
  229. [ 1.542291] stm32-dwmac 5800a000.ethernet: DMA HW capability register supported
  230. [ 1.549656] stm32-dwmac 5800a000.ethernet: RX Checksum Offload Engine supported
  231. [ 1.556977] stm32-dwmac 5800a000.ethernet: TX Checksum insertion supported
  232. [ 1.563840] stm32-dwmac 5800a000.ethernet: Wake-Up On Lan supported
  233. [ 1.570202] stm32-dwmac 5800a000.ethernet: TSO supported
  234. [ 1.575475] stm32-dwmac 5800a000.ethernet: Enable RX Mitigation via HW Watchdog Timer
  235. [ 1.583314] stm32-dwmac 5800a000.ethernet (unnamed net_device) (uninitialized): device MAC address a2:df:a4:b5:a9:a0
  236. [ 1.593881] stm32-dwmac 5800a000.ethernet: TSO feature enabled
  237. [ 1.599954] libphy: stmmac: probed
  238. [ 1.603406] mdio_bus stmmac-0: MDIO device at address 1 is missing.
  239. [ 1.611028] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
  240. [ 1.617131] usbcore: registered new interface driver pegasus
  241. [ 1.622722] usbcore: registered new interface driver asix
  242. [ 1.628157] usbcore: registered new interface driver ax88179_178a
  243. [ 1.634217] usbcore: registered new interface driver cdc_ether
  244. [ 1.640134] usbcore: registered new interface driver smsc75xx
  245. [ 1.645900] usbcore: registered new interface driver smsc95xx
  246. [ 1.651583] usbcore: registered new interface driver net1080
  247. [ 1.657289] usbcore: registered new interface driver cdc_subset
  248. [ 1.663184] usbcore: registered new interface driver zaurus
  249. [ 1.668851] usbcore: registered new interface driver cdc_ncm
  250. [ 1.674978] dwc2 49000000.usb-otg: 49000000.usb-otg supply vusb_d not found, using dummy regulator
  251. [ 1.683555] dwc2 49000000.usb-otg: Linked as a consumer to regulator.0
  252. [ 1.689980] dwc2 49000000.usb-otg: 49000000.usb-otg supply vusb_a not found, using dummy regulator
  253. [ 1.699832] dwc2 49000000.usb-otg: Linked as a consumer to regulator.5
  254. [ 1.705594] dwc2 49000000.usb-otg: EPs: 9, dedicated fifos, 952 entries in SPRAM
  255. [ 1.714604] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  256. [ 1.719785] ehci-platform: EHCI generic platform driver
  257. [ 1.725382] ehci-platform 5800d000.usbh-ehci: Linked as a consumer to regulator.1
  258. [ 1.732501] ehci-platform 5800d000.usbh-ehci: EHCI Host Controller
  259. [ 1.738712] ehci-platform 5800d000.usbh-ehci: new USB bus registered, assigned bus number 1
  260. [ 1.747364] ehci-platform 5800d000.usbh-ehci: irq 52, io mem 0x5800d000
  261. [ 1.775216] ehci-platform 5800d000.usbh-ehci: USB 2.0 started, EHCI 1.00
  262. [ 1.781758] hub 1-0:1.0: USB hub found
  263. [ 1.784282] hub 1-0:1.0: 2 ports detected
  264. [ 1.789761] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  265. [ 1.794558] ohci-platform: OHCI generic platform driver
  266. [ 1.800213] ohci-platform 5800c000.usbh-ohci: Generic Platform OHCI controller
  267. [ 1.807067] ohci-platform 5800c000.usbh-ohci: new USB bus registered, assigned bus number 2
  268. [ 1.815687] ohci-platform 5800c000.usbh-ohci: irq 51, io mem 0x5800c000
  269. [ 1.890383] hub 2-0:1.0: USB hub found
  270. [ 1.892736] hub 2-0:1.0: 2 ports detected
  271. [ 1.899111] usbcore: registered new interface driver usb-storage
  272. [ 1.908707] stm32_rtc 5c004000.rtc: rtc core: registered 5c004000.rtc as rtc0
  273. [ 1.914804] stm32_rtc 5c004000.rtc: Date/Time must be initialized
  274. [ 1.920586] stm32_rtc 5c004000.rtc: registered rev:1.2
  275. [ 1.926307] i2c /dev entries driver
  276. [ 1.949678] stm32f7-i2c 5c002000.i2c: using dma0chan0 (tx) and dma0chan1 (rx) for DMA transfers
  277. [ 1.958376] stm32f7-i2c 5c002000.i2c: STM32F7 I2C-0 bus adapter
  278. [ 1.967840] mmci-pl18x 48004000.sdmmc: allocated mmc-pwrseq
  279. [ 1.972202] mmci-pl18x 48004000.sdmmc: Linked as a consumer to regulator.2
  280. [ 1.979177] mmci-pl18x 48004000.sdmmc: mmc0: PL180 manf 53 rev1 at 0x48004000 irq 42,0 (pio)
  281. [ 2.015740] mmci-pl18x 58005000.sdmmc: Linked as a consumer to regulator.2
  282. [ 2.021292] mmci-pl18x 58005000.sdmmc: mmc1: PL180 manf 53 rev2 at 0x58005000 irq 46,0 (pio)
  283. [ 2.057913] mmci-pl18x 58007000.sdmmc: Linked as a consumer to regulator.2
  284. [ 2.063483] mmci-pl18x 58007000.sdmmc: mmc2: PL180 manf 53 rev2 at 0x58007000 irq 47,0 (pio)
  285. [ 2.070819] random: fast init done
  286. [ 2.098601] sdhci: Secure Digital Host Controller Interface driver
  287. [ 2.103407] sdhci: Copyright(c) Pierre Ossman
  288. [ 2.107746] Synopsys Designware Multimedia Card Interface Driver
  289. [ 2.110673] mmc1: host does not support reading read-only switch, assuming write-enable
  290. [ 2.114288] sdhci-pltfm: SDHCI platform and OF driver helper
  291. [ 2.128805] mmc1: new high speed SDHC card at address aaaa
  292. [ 2.133046] ledtrig-cpu: registered to indicate activity on CPUs
  293. [ 2.139919] usbcore: registered new interface driver usbhid
  294. [ 2.144520] usbhid: USB HID core driver
  295. [ 2.146168] mmcblk1: mmc1:aaaa SL08G 7.40 GiB
  296. [ 2.159930] stm32-rproc m4@0: mbox_request_channel_byname() requires an "mbox-names" property
  297. [ 2.167098] remoteproc remoteproc0: cannot get vq0 mbox
  298. [ 2.172265] stm32-rproc m4@0: mbox_request_channel_byname() requires an "mbox-names" property
  299. [ 2.180867] remoteproc remoteproc0: cannot get vq1 mbox
  300. [ 2.186089] stm32-rproc m4@0: mbox_request_channel_byname() requires an "mbox-names" property
  301. [ 2.194602] remoteproc remoteproc0: cannot get shutdown mbox
  302. [ 2.200426] remoteproc remoteproc0: m4 is available
  303. [ 2.208373] stm32-ddr-pmu: probed (ID=0x00140061 VER=0x00000010), DDR@533MHz
  304. [ 2.217932] NET: Registered protocol family 17
  305. [ 2.220944] can: controller area network core (rev 20170425 abi 9)
  306. [ 2.227287] NET: Registered protocol family 29
  307. [ 2.231572] can: raw protocol (rev 20170425)
  308. [ 2.235886] can: broadcast manager protocol (rev 20170425 t)
  309. [ 2.241528] can: netlink gateway (rev 20170425) max_hops=1
  310. [ 2.247580] Key type dns_resolver registered
  311. [ 2.251438] ThumbEE CPU extension supported.
  312. [ 2.255628] Registering SWP/SWPB emulation handler
  313. [ 2.261593] registered taskstats version 1
  314. [ 2.264464] Loading compiled-in X.509 certificates
  315. [ 2.294729] [drm] ltdc hw version 0x00010300 - ready
  316. [ 2.298423] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
  317. [ 2.304878] [drm] Driver supports precise vblank timestamp query.
  318. [ 2.311925] [drm] Initialized stm 1.0.0 20170330 for 5a001000.display-controller on minor 0
  319. [ 2.320413] stm32_rtc 5c004000.rtc: setting system clock to 2000-01-01 00:00:29 UTC (946684829)
  320. [ 2.329093] ALSA device list:
  321. [ 2.331060] No soundcards found.
  322. [ 2.336567] VFS: Cannot open root device "mmcblk1p6" or unknown-block(179,6): error -6
  323. [ 2.343048] Please append a correct "root=" boot option; here are the available partitions:
  324. [ 2.351493] 0100 65536 ram0
  325. [ 2.351498] (driver?)
  326. [ 2.357617] 0101 65536 ram1
  327. [ 2.357621] (driver?)
  328. [ 2.363647] 0102 65536 ram2
  329. [ 2.363651] (driver?)
  330. [ 2.369758] 0103 65536 ram3
  331. [ 2.369761] (driver?)
  332. [ 2.375898] 0104 65536 ram4
  333. [ 2.375901] (driver?)
  334. [ 2.381974] 0105 65536 ram5
  335. [ 2.381977] (driver?)
  336. [ 2.388083] 0106 65536 ram6
  337. [ 2.388087] (driver?)
  338. [ 2.394190] 0107 65536 ram7
  339. [ 2.394193] (driver?)
  340. [ 2.400300] 0108 65536 ram8
  341. [ 2.400304] (driver?)
  342. [ 2.406436] 0109 65536 ram9
  343. [ 2.406439] (driver?)
  344. [ 2.412516] 010a 65536 ram10
  345. [ 2.412520] (driver?)
  346. [ 2.418714] 010b 65536 ram11
  347. [ 2.418718] (driver?)
  348. [ 2.424908] 010c 65536 ram12
  349. [ 2.424911] (driver?)
  350. [ 2.431106] 010d 65536 ram13
  351. [ 2.431110] (driver?)
  352. [ 2.437320] 010e 65536 ram14
  353. [ 2.437323] (driver?)
  354. [ 2.443495] 010f 65536 ram15
  355. [ 2.443498] (driver?)
  356. [ 2.449698] b300 7761920 mmcblk1
  357. [ 2.449702] driver: mmcblk
  358. [ 2.456534] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,6)
  359. [ 2.464963] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.19.94 #1
  360. [ 2.470977] Hardware name: STM32 (Device Tree Support)
  361. [ 2.476163] [<c0111b34>] (unwind_backtrace) from [<c010d734>] (show_stack+0x10/0x14)
  362. [ 2.483905] [<c010d734>] (show_stack) from [<c0a08d88>] (dump_stack+0xb0/0xc4)
  363. [ 2.491150] [<c0a08d88>] (dump_stack) from [<c01256bc>] (panic+0xfc/0x268)
  364. [ 2.498044] [<c01256bc>] (panic) from [<c0f0166c>] (mount_block_root+0x1cc/0x274)
  365. [ 2.505548] [<c0f0166c>] (mount_block_root) from [<c0f01978>] (mount_root+0x120/0x13c)
  366. [ 2.513488] [<c0f01978>] (mount_root) from [<c0f01b10>] (prepare_namespace+0x17c/0x1c4)
  367. [ 2.521517] [<c0f01b10>] (prepare_namespace) from [<c0f01258>] (kernel_init_freeable+0x3cc/0x3dc)
  368. [ 2.530420] [<c0f01258>] (kernel_init_freeable) from [<c0a1d7ac>] (kernel_init+0x8/0x110)
  369. [ 2.538620] [<c0a1d7ac>] (kernel_init) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
  370. [ 2.546203] Exception stack(0xee8affb0 to 0xee8afff8)
  371. [ 2.551267] ffa0: 00000000 00000000 00000000 00000000
  372. [ 2.559472] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
  373. [ 2.567673] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000
  374. [ 2.574312] CPU0: stopping
  375. [ 2.577010] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.94 #1
  376. [ 2.583025] Hardware name: STM32 (Device Tree Support)
  377. [ 2.588190] [<c0111b34>] (unwind_backtrace) from [<c010d734>] (show_stack+0x10/0x14)
  378. [ 2.595951] [<c010d734>] (show_stack) from [<c0a08d88>] (dump_stack+0xb0/0xc4)
  379. [ 2.603194] [<c0a08d88>] (dump_stack) from [<c0110838>] (handle_IPI+0x41c/0x444)
  380. [ 2.610614] [<c0110838>] (handle_IPI) from [<c04fff34>] (gic_handle_irq+0x8c/0x90)
  381. [ 2.618204] [<c04fff34>] (gic_handle_irq) from [<c0101a0c>] (__irq_svc+0x6c/0xa8)
  382. [ 2.625698] Exception stack(0xc1001f28 to 0xc1001f70)
  383. [ 2.630766] 1f20: 00000000 0000b7c0 ef70c48c c011b1e0 ffffe000 c1004cb4
  384. [ 2.638971] 1f40: c1004cf4 00000001 c10a5b2d c0ca78ec c0f5aa38 c1004c88 c1004db0 c1001f78
  385. [ 2.647170] 1f60: c010a0cc c010a0d0 60000013 ffffffff
  386. [ 2.652240] [<c0101a0c>] (__irq_svc) from [<c010a0d0>] (arch_cpu_idle+0x38/0x3c)
  387. [ 2.659659] [<c010a0d0>] (arch_cpu_idle) from [<c0156680>] (do_idle+0x10c/0x14c)
  388. [ 2.667075] [<c0156680>] (do_idle) from [<c0156988>] (cpu_startup_entry+0x18/0x20)
  389. [ 2.674668] [<c0156988>] (cpu_startup_entry) from [<c0f00e5c>] (start_kernel+0x480/0x4b0)
  390. [ 2.682869] [<c0f00e5c>] (start_kernel) from [<00000000>] ( (null))
  391. [ 2.689250] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,6) ]---
RAW Paste Data