Guest User

Untitled

a guest
Jun 4th, 2020
83
0
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 2.30 KB | None | 0 0
  1. # For more options and information see
  2. # http://rpf.io/configtxt
  3. # Some settings may impact device functionality. See link above for details
  4.  
  5. # uncomment if you get no picture on HDMI for a default "safe" mode
  6. #hdmi_safe=1
  7.  
  8. # uncomment this if your display has a black border of unused pixels visible
  9. # and your display can output without overscan
  10. disable_overscan=0
  11.  
  12. # uncomment the following to adjust overscan. Use positive numbers if console
  13. # goes off screen, and negative if there is too much border
  14. #overscan_left=16
  15. #overscan_right=16
  16. #overscan_top=16
  17. #overscan_bottom=16
  18.  
  19. # uncomment to force a console size. By default it will be display's size minus
  20. # overscan.
  21. #framebuffer_width=1280
  22. #framebuffer_height=720
  23.  
  24. # uncomment if hdmi display is not detected and composite is being output
  25. #hdmi_force_hotplug=1
  26.  
  27. # uncomment to force a specific HDMI mode (this will force VGA)
  28. #hdmi_group=1
  29. #hdmi_mode=1
  30.  
  31. # uncomment to force a HDMI mode rather than DVI. This can make audio work in
  32. # DMT (computer monitor) modes
  33. hdmi_drive=2
  34.  
  35. # Setting hdmi_force_hotplug to 1 pretends that the HDMI hotplug signal is asserted, so it appears that a HDMI display is attached. In other words, HDMI output mode will be used, even if no HDMI monitor is detected.
  36. hdmi_force_hotplug=1
  37.  
  38. # Pretends all audio formats are supported by display, allowing passthrough of DTS/AC even when not reported as supported.
  39. # May not be needed for all HDMI devices
  40. hdmi_force_edid_audio=1
  41.  
  42. # uncomment to increase signal to HDMI, if you have interference, blanking, or
  43. # no display
  44. #config_hdmi_boost=4
  45.  
  46. # uncomment for composite PAL
  47. #sdtv_mode=2
  48.  
  49. #uncomment to overclock the arm. 700 MHz is the default.
  50. #arm_freq=800
  51.  
  52. # Uncomment some or all of these to enable the optional hardware interfaces
  53. #dtparam=i2c_arm=on
  54. #dtparam=i2s=on
  55. #dtparam=spi=on
  56.  
  57. # Uncomment this to enable infrared communication.
  58. #dtoverlay=gpio-ir,gpio_pin=17
  59. #dtoverlay=gpio-ir-tx,gpio_pin=18
  60.  
  61. # Additional overlays and parameters are documented /boot/overlays/README
  62.  
  63. # Enable audio (loads snd_bcm2835)
  64. dtparam=audio=on
  65.  
  66. [pi4]
  67. # Enable DRM VC4 V3D driver on top of the dispmanx display stack
  68. dtoverlay=vc4-fkms-v3d
  69. max_framebuffers=2
  70.  
  71. [all]
  72. #dtoverlay=vc4-fkms-v3d
  73. gpu_mem_256=128
  74. gpu_mem_512=256
  75. gpu_mem_1024=256
  76. overscan_scale=1
Add Comment
Please, Sign In to add comment