Supra Coils/wheels

015-11-29 00:01:52  ★ Richard Hawkins would then walk to the toolstation as he then bends down and picks up the toolbox with
2015-11-29 00:01:57  ★ his right hand.      ((Richard Hawkins))
2015-11-29 00:02:11  ★ Richard Hawkins would then stand back up as he then takes it to the Supra.
2015-11-29 00:03:06  ★ Richard Hawkins would then place the toolbox down next to the supra.
2015-11-29 00:03:31  ★ Richard Hawkins would then walk to the driverside door, as he then reaches for the handle with his right
2015-11-29 00:03:40  ★ hand and pulls on it, opening the door.      ((Richard Hawkins))
2015-11-29 00:04:12  ★ Richard Hawkins would then bend down as he then reaches out for the lever as he then pulls on it, opening
2015-11-29 00:04:14  ★ the hood.      ((Richard Hawkins))
2015-11-29 00:04:38  ★ Richard Hawkins would then stand back up as he then shuts the door and walks to the front of the car.
2015-11-29 00:05:13  ★ Richard Hawkins would then slide his fingers under the hood of the supra as he then flicks a switch and
2015-11-29 00:05:19  ★ lifts the hood up.      ((Richard Hawkins))
2015-11-29 00:06:04  ★ Richard Hawkins would then walk to the toolstation as he then picks up 4 plastic pads, with both of his hand
2015-11-29 00:06:09  ★ -s      ((Richard Hawkins))
2015-11-29 00:06:30  ★ Richard Hawkins would then walk back to the supra as he then places one of the each pad to each end of the
2015-11-29 00:06:35  ★ sideskirts-      ((Richard Hawkins))
2015-11-29 00:07:30  ★ after he has done that, he would walk over to the lifts control panel.      ((Richard Hawkins))
2015-11-29 00:07:47  ★ Richard Hawkins would then press on one of the buttons, raising the middle part of the lift.
2015-11-29 00:08:16  ★ Richard Hawkins would take his finger off the button when all four wheels of the supra are off the ground.
2015-11-29 00:09:49  ★ Richard Hawkins would then walk to the toolbox as he then crouches down to it, and uses both of his hands
2015-11-29 00:09:52  ★ to open it.      ((Richard Hawkins))
2015-11-29 00:10:25  ★ Richard Hawkins would then reach for the breaker bar and 17mm socket as he then connects the two.
2015-11-29 00:11:53  ★ Richard Hawkins would then use the breaker bar to loosen and remove all five wheelnuts.
2015-11-29 00:12:19  ★ Richard Hawkins would then put the wheelnuts into his pocket as he then places the breaker bar down
2015-11-29 00:12:40  ★ and grabs ahold of the wheel as he then pulls on it and removes it from the wheelhub.      ((Richard Hawkins))
2015-11-29 00:14:46  ★ Richard Hawkins would then stand up and rolls the wheel to the wall of the garage and leans it against the
2015-11-29 00:14:46  ★ wall.      ((Richard Hawkins))
2015-11-29 00:14:59  ★ Richard Hawkins would then walk back to the toolbox as he then crouches down to it and reaches for the
2015-11-29 00:15:17  ★ socket wrench and the 13mm socket , as he then connects the two.      ((Richard Hawkins))
2015-11-29 00:18:33  ★ Richard Hawkins would then move back to the wheelhub as he then uses the socket to remove the two bolts and
2015-11-29 00:18:46  ★ nuts, as he then places both of them into his pocket.      ((Richard Hawkins))
2015-11-29 00:19:44  ★ the coilover would now be disconnected from the front steering rack.      ((Richard Hawkins))
2015-11-29 00:20:05  ★ Richard Hawkins would then stand up as he then uses the socket wrench with the 13 mm socket to loosen up and
2015-11-29 00:20:55  ★ remove the 3 nuts from the engine bay, connecting the coilover to the chassis.      ((Richard Hawkins))
2015-11-29 00:21:16  ★ Richard Hawkins would then crouch back down as he then places the socket wrench to the side.
2015-11-29 00:21:49  ★ Richard Hawkins would then grab ahold of the coilover with both of his hands as he then pulls it away from
2015-11-29 00:21:52  ★ the wheelhub.      ((Richard Hawkins))
2015-11-29 00:22:21  ★ Richard Hawkins would then stand up and walk to the toolstation with the coilover still in his hands.
2015-11-29 00:22:48  ★ Richard Hawkins would then compare the old coilover to the new one as he then places the old one down onto
2015-11-29 00:22:52  ★ the ground.      ((Richard Hawkins))
2015-11-29 00:23:12  ★ Richard Hawkins would then stand up as he then grabs ahold of the new coilover and walks back to the supra w
2015-11-29 00:23:15  ★ with it.      ((Richard Hawkins))
2015-11-29 00:23:44  ★ Richard Hawkins would then crouch down to the wheelhub as he then aligns the coilover with the holes in the
2015-11-29 00:23:47  ★ chassis.      ((Richard Hawkins))
2015-11-29 00:26:04  ★ Richard Hawkins would then rest the coilover onto the front steering knuckle, as he then grabs ahold of the
2015-11-29 00:26:19  ★ socket wrench and stands up as he then takes 3 nuts from his pocket and tightens them by      ((Richard Hawkins))
2015-11-29 00:26:19  ★ hand.      ((Richard Hawkins))
2015-11-29 00:26:26  ★ Richard Hawkins would then use the socketwrench to tighten all 3 nuts in the engine bay as he then crouches
2015-11-29 00:26:34  ★ back down to the wheelhub      ((Richard Hawkins))
2015-11-29 00:27:50  ★ Richard Hawkins would then take out 2 bolts and nuts from his pocket as he then slides the bolts into the
2015-11-29 00:27:52  ★ place.      ((Richard Hawkins))
2015-11-29 00:28:21  ★ Richard Hawkins would then hand tighten the two nuts and uses the socket wrench to tighten the nuts
2015-11-29 00:28:26  ★ as hard as he can.      ((Richard Hawkins))
2015-11-29 00:28:55  ★ Richard Hawkins would then stand up as he then walks to the toolstation and rolls out a wheel from the-
2015-11-29 00:28:59  ★ corner.      ((Richard Hawkins))
2015-11-29 00:29:28  ★ it would appear to be APEX rim with Toyo Proxes R888 Tyres on it.      ((Richard Hawkins))
2015-11-29 00:31:35  ★ Richard Hawkins would then roll the wheel to the front of the supra as he then grabs ahold of the rim and
2015-11-29 00:31:48  ★ lifts it to the wheelhub.      ((Richard Hawkins))
2015-11-29 00:32:09  ★ Richard Hawkins would then take the wheelnuts form his pocket as he then hand tightens them.
2015-11-29 00:32:37  ★ Richard Hawkins would then reach for the breaker bar as he then disconnects the 17mm socket from it.
2015-11-29 00:33:05  ★ Richard Hawkins would then place the breaker bar down as he then reaches into his toolbox and reaches
2015-11-29 00:33:19  ★ out for the torque bar, he would grab it with his right hand.      ((Richard Hawkins))
2015-11-29 00:33:51  ★ Richard Hawkins would then connect the 17mm socket to the torque bar and sets the torque to 135NM
2015-11-29 00:34:19  ★ Richard Hawkins would then use the torque bar to tighten all 5 wheelnuts of the supra.
2015-11-29 00:36:18  ★ Richard Hawkins would repeat the same action on all 3 wheels and coilovers.
2015-11-29 00:36:37  ★ after doing so he would walk around the supra, picking up the tools and placing them into      ((Richard Hawkins))
2015-11-29 00:36:40  ★ the toolbox.      ((Richard Hawkins))
2015-11-29 00:37:08  ★ Richard Hawkins would then bend down to the toolbox as he then picks it up and takes it to the toolstation
2015-11-29 00:37:19  ★ and places it down next to it.      ((Richard Hawkins))