API tools faq
paste
rtsc

Buffalo WSR3600BE4P Serial console boot messages

rtsc
Oct 10th, 2026 (edited)
38
0
Never
3
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 69.98 KB | None | 0 0
raw download clone embed print report
  1. J1 115200bps 8N1
  2.  
  3. --------------------------------------------------
  4. Secure key does not exist
  5. phy_config efuse load.
  6. phy efuse load done.
  7. phy_config efuse load done
  8. bus2dram in_order mode
  9. HWCONF is 1f
  10.  
  11. AN7552DRAMC V0.4
  12. MPLL setting done !!!
  13. dram_type = PCDDR3, data_rate = 1866
  14. DIV mode = 2
  15. APHY RG Setting
  16. DelayCellTimex100 (cell=1104)
  17. MRW RK0 MR#2 = 0x220
  18. MRW RK0 MR#3 = 0x0
  19. MRW RK0 MR#1 = 0x0
  20. MRW RK0 MR#0 = 0x1114
  21. [Dramc] PCDDR AC Timing update
  22. DRVP driving setting info: 0x40
  23. ODTP driving setting info: 0x40
  24. DRVN driving setting info: 0x40
  25. ODTN driving setting info: 0x40
  26. MRW RK0 MR#2 = 0x20
  27. MRW RK0 MR#1 = 0x80
  28. MRW RK0 MR#1 = 0x0
  29. MRW RK0 MR#2 = 0x220
  30. MRW RK0 MR#3 = 0x4
  31. MRW RK0 MR#3 = 0x0
  32. DRAM FLOW DONE!!!
  33. Secure key does not exist
  34. phy_config efuse load.
  35. phy efuse load done.
  36. phy_config efuse load done
  37. [BUF] Start initializing gpio setting from 0x7c004...
  38. [BUF] Sig MTK_GPIO_LOW found! (1,4,12,7,11,21)
  39. [BUF] Start to set GPIO1=0
  40. [BUF] Start to set GPIO4=0
  41. [BUF] Start to set GPIO12=0
  42. [BUF] Start to set GPIO7=0
  43. [BUF] Start to set GPIO11=0
  44. [BUF] Start to set GPIO21=0
  45. [BUF] Sig MTK_GPIO_HIGH found! (6,27)
  46. [BUF] Start to set GPIO6=1
  47. [BUF] Start to set GPIO27=1
  48. L2C_type:256K_L2C
  49. L1D cache size: 32 KB (with set/asso/line==128/4/64)
  50. L1I cache size: 32 KB (with set/asso/line==256/2/64)
  51. L2U cache size: 256 KB (with set/asso/line==256/16/64)
  52.  
  53.  
  54. BUFFALO BOOT for WSR3600BE4P v1.2 (Feb 06 2025 - 00:00:05)
  55.  
  56. DRAM: 512 MiB
  57. AN7563PT
  58. [BUF] Start uboot gpio init...
  59. Now running in RAM - U-Boot at: 9edc2000
  60. spi_nand_probe: mfr_id=0xc8, dev_id=0x92
  61. Using Flash ECC.
  62. Detected SPI NAND Flash : _SPI_NAND_DEVICE_ID_GD5F2GM7UE, Flash Size=0x10000000
  63. bmt pool size: 163
  64. BMT & BBT Init Success
  65. MTDPARTS: 512k[u-boot-env],4m[Factory],256k[ORGDATA],80m[tclinux],80m[tclinux_slave],10m[syslog_data],46336k[user_property]
  66. FDT_MAGIC or IH_MAGIC check fail.
  67. Parse main image fail.
  68. NAND: 0 MiB
  69. * check ORGDATA
  70. read ORGDATA(+00000000) partition...(176)
  71. load ORGDATA...176/0/176
  72. vaild crc.
  73. check product = WSR3600BE4P / WSR3600BE4P (32)
  74. check ethaddr = ec:5a:31:ec:85:80 / ec:5a:31:ec:85:80 (6)
  75. check wlan0addr = ec:5a:31:ec:85:88 / ec:5a:31:ec:85:88 (6)
  76. check wlan1addr = ec:5a:31:ec:85:90 / ec:5a:31:ec:85:90 (6)
  77. check hw_rev = 0 / 0 (4)
  78. check custom_id = 0 / 0 (4)
  79. check melco_id = RD_24041 / RD_24041 (12)
  80. check region = JP / JP (4)
  81. check vendor = BUFFALO / BUFFALO (16)
  82. ### Memory Test Start: 81800000 - 9C000000 RAM: 1f000000
  83. -> Data line test start:0x81800000
  84. pattern:
  85. 0x00000001
  86. 0x00000003
  87. 0x00000007
  88. 0x0000000F
  89. 0x00000005
  90. 0x00000015
  91. 0x00000055
  92. 0xAAAAAAAA
  93. =>PASS
  94. -> Address line test
  95. start:0x81800000 len:0x06a00000
  96. =>PASS
  97. -> Fill memory pattern test(fast)
  98. Check pattern 00000000AAAAAAAA
  99. =>PASS
  100. In: serial
  101. Out: serial
  102. Err: serial
  103. CPU0: found redistributor 0 region 0:9ee374c8
  104. Net: ecnt_eth
  105. Uip activated
  106. ETHERWAN & HSGMII mode
  107. pon-serdes setting
  108. pon-serdes setting done
  109. [MTK[mtk_mw_cmd][588] [addr, writeval] = [0x1fa20218, 0x10]
  110. Hit any key to stop autoboot: 3  2  1  0
  111. firmware hash is same -> [CURRENT]
  112. Loading partition0(81800000) from 0x00540030/25564160 byte(s)
  113.  
  114. SUCCESS!
  115. Reading kernel...
  116. bootm flag=0, states=70f
  117. ## Loading kernel from FIT Image at 81800000 ...
  118. Using 'conf@1' configuration
  119. Trying 'kernel@1' kernel subimage
  120. Description: ARM OpenWrt Linux-5.4.55
  121. Type: Kernel Image
  122. Compression: lzma compressed
  123. Data Start: 0x81802aa8
  124. Data Size: 3209463 Bytes = 3.1 MiB
  125. Architecture: ARM
  126. OS: Linux
  127. Load Address: 0x80088000
  128. Entry Point: 0x80088000
  129. Hash algo: sha1
  130. Hash value: 44a15607efa2959e1baf87d91ef1734ca0b5cdc0
  131. Verifying Hash Integrity ... sha1+ OK
  132. ## Loading fdt from FIT Image at 81800000 ...
  133. Using 'conf@1' configuration
  134. Trying 'fdt@1' fdt subimage
  135. Description: ARM OpenWrt en7552_wsr3600be4_evb.dtb device tree blob
  136. Type: Flat Device Tree
  137. Compression: uncompressed
  138. Data Start: 0x818000fc
  139. Data Size: 10539 Bytes = 10.3 KiB
  140. Architecture: ARM
  141. Verifying Hash Integrity ... OK
  142. Booting using the fdt blob at 0x818000fc
  143. Uncompressing Kernel Image ... OK
  144. Loading Device Tree to 9cdb5000, end 9cdba92a ... OK
  145.  
  146. Starting kernel ...
  147.  
  148. ** 18 printk messages dropped **
  149. [ 0.000000] npu_pkt_buffer memblock_alloc:9b7b5000,buf_size=1600000
  150. [ 0.000000] percpu: Embedded 15 pages/cpu s31052 r8192 d22196 u61440
  151. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129472
  152. [ 0.000000] Kernel command line: sdram_conf=0x00108893 vendor_name=Buffalo inc. product_name=WSR3600BE4P ethaddr=ec:5a:31:ec:85:80 snmp_sysobjid=1.2.3.4.5 country_code=ff ether_gpio=0c power_gpio=1515 username=admin dsl_gpio=0b internet_gpio=02 multi_upgrade_gpio=0b020400000000000000000000000000 onu_type=2 qdma_init=11 root=/dev/mtdblock6 ro console=ttyS0,115200n8 earlycon bootflag=0 serdes_sel=0 serdes_pon=121 tclinux_info=0x185f24f,0x4aa8,0x30f8f7,0x314498,0x154c888
  153. [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
  154. [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
  155. [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
  156. [ 0.000000] Memory: 449864K/523008K available (7168K kernel code, 245K rwdata, 1508K rodata, 1024K init, 896K bss, 73144K reserved, 0K cma-reserved, 0K highmem)
  157. [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  158. [ 0.000000] rcu: Hierarchical RCU implementation.
  159. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
  160. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 64
  161. [ 0.000000] GICv3: 256 SPIs implemented
  162. [ 0.000000] GICv3: 0 Extended SPIs implemented
  163. [ 0.000000] GICv3: Distributor has no Range Selector support
  164. [ 0.000000] GICv3: 16 PPIs implemented
  165. [ 0.000000] GICv3: no VLPI support, no direct LPI support
  166. [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x09080000
  167. [ 0.000000] random: get_random_bytes called from start_kernel+0x2a4/0x3d0 with crng_init=0
  168. [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (virt).
  169. [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
  170. [ 0.000004] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
  171. [ 0.000010] Switching to timer-based delay loop, resolution 40ns
  172. [ 0.000089] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
  173. [ 0.000097] pid_max: default: 32768 minimum: 301
  174. [ 0.000197] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
  175. [ 0.000206] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
  176. [ 0.000719] CPU: Testing write buffer coherency: ok
  177. [ 0.000913] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
  178. [ 0.001223] Setting up static identity map for 0x80100000 - 0x80100060
  179. [ 0.001285] rcu: Hierarchical SRCU implementation.
  180. [ 0.001399] gic-its@09020000: unable to locate ITS domain
  181. [ 0.001541] smp: Bringing up secondary CPUs ...
  182. [ 0.001929] GICv3: CPU1: found redistributor 1 region 0:0x090a0000
  183. [ 0.001955] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
  184. [ 0.002054] smp: Brought up 1 node, 2 CPUs
  185. [ 0.002064] SMP: Total of 2 processors activated (100.00 BogoMIPS).
  186. [ 0.002069] CPU: All CPU(s) started in SVC mode.
  187. [ 0.004071] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  188. [ 0.004087] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
  189. [ 0.004419] NET: Registered protocol family 16
  190. [ 0.004664] DMA: preallocated 256 KiB pool for atomic coherent allocations
  191. [ 0.005786] cpuidle: using governor menu
  192. [ 0.005883] No ATAGs?
  193. [ 0.005883] an7552_serdes_common_phy_probe
  194. [ 0.011106] serdes_common_phy->Ana_csr_base= e0868000
  195. [ 0.011110] serdes_common_phy->Dig_csr_base= e086a000
  196. [ 0.011114] serdes_common_phy->Multi_sgmii_base= e086c000
  197. [ 0.011171]
  198. [ 0.011171] l2c_sram_size:0x0
  199. [ 0.011175]
  200. [ 0.011175] kthread_run(reset_pcie_wifi_thread_act
  201. [ 0.013848] Initializing Ecnt Event Netlink Socket
  202. [ 0.013868] Initializing Econet Event Netlink Socket nl_sk = (ptrval)
  203. [ 0.018294] ecnt-hsdma 1fa01800.dma-controller: Econet HSDMA driver registered
  204. [ 0.018394] iommu: Default domain type: Translated
  205. [ 0.018526] usbcore: registered new interface driver usbfs
  206. [ 0.018554] usbcore: registered new interface driver hub
  207. [ 0.018590] usbcore: registered new device driver usb
  208. [ 0.018633] ecnt_usb->uphy_base = e0876000
  209. [ 0.019030] NET: Registered protocol family 8
  210. [ 0.019035] NET: Registered protocol family 20
  211. [ 0.019310] clocksource: Switched to clocksource arch_sys_counter
  212. [ 0.019800] thermal_sys: Registered thermal governor 'step_wise'NET: Registered protocol family 2
  213. [ 0.020447] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
  214. [ 0.020471] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
  215. [ 0.020509] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
  216. [ 0.020568] TCP: Hash tables configured (established 4096 bind 4096)
  217. [ 0.020620] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
  218. [ 0.020638] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
  219. [ 0.020746] NET: Registered protocol family 1
  220. [ 0.020765] PCI: CLS 0 bytes, default 64
  221. [ 0.021009]
  222. [ 0.021009] XPON xsgmii_drv_probe
  223. [ 0.021014]
  224. [ 0.021014] XPON_XSGMII driver version: 7552.4.20230915
  225. [ 0.021014] improve jit tol setting
  226. [ 0.021019] sgmii:int_id: 0
  227. [ 0.021023] xsgmii_get_base
  228. [ 0.021027]
  229. [ 0.021027] common_phy Get_Base:0x1faf3000
  230. [ 0.021031]
  231. [ 0.021031] common_phy Get_Base:0x1faf4000
  232. [ 0.021034]
  233. [ 0.021034] common_phy Get_Base:0x1fa84000
  234. [ 0.021062] sgmii:int_name: xpon_xsgmii
  235. [ 0.021066] XOPN_xsgmii region= 3
  236. [ 0.021073] XOPN_xsgmii->pcs2_base = 0xe0879a00
  237. [ 0.021077] XOPN_xsgmii->an_base = 0xe087b000
  238. [ 0.021081] XOPN_xsgmii->ra_base = 0xe087d000
  239. [ 0.021085] XOPN_xsgmii->phya_base = 0xe0868000
  240. [ 0.021090] XOPN_xsgmii->multi_sgmii_base = 0xe086c000
  241. [ 0.021094] XOPN_xsgmii->pma_base = 0xe086a000
  242. [ 0.021170] xsgmii_proc_init
  243. [ 0.021485] ecnt-frame_engine 1fb50000.frame_engine: IRQ index 10 not found
  244. [ 0.021495] ecnt-frame_engine 1fb50000.frame_engine: IRQ index 11 not found
  245. [ 0.021504] ecnt-frame_engine 1fb50000.frame_engine: IRQ index 12 not found
  246. [ 0.021512] ecnt-frame_engine 1fb50000.frame_engine: IRQ index 13 not found
  247. [ 0.021521] ecnt-frame_engine 1fb50000.frame_engine: IRQ index 14 not found
  248. [ 0.021530] ecnt-frame_engine 1fb50000.frame_engine: IRQ index 15 not found
  249. [ 0.021538] ecnt-frame_engine 1fb50000.frame_engine: IRQ index 16 not found
  250. [ 0.021547] ecnt-frame_engine 1fb50000.frame_engine: IRQ index 17 not found
  251. [ 0.021846] ecnt-npu 1e800000.npu: ecnt_npu use 1GB DMA for coherent map
  252. [ 0.022067] irq-0: 110 irq-1: 111
  253. [ 0.022067] (ecnt_pon_phy_probe) probe start
  254. [ 0.022173] (ecnt_pon_phy_probe) rg_base1= 0xe096c000
  255. [ 0.022181]
  256. [ 0.022181] common_phy Get_Base:0x1faf3000
  257. [ 0.022185]
  258. [ 0.022185] common_phy Get_Base:0x1faf4000
  259. [ 0.022426] test_uc:(ptrval) test_c:(ptrval) cpu_top->base:(ptrval)
  260. [ 0.022489] [apb_timer] ecnt_timer_drv_probe
  261. [ 0.022506] [timer] res->name:apb_timer1@1fbf0100
  262. [ 0.022630]
  263. [ 0.022630] i2c_slave init(ecnt_i2c_slave_drv_probe) done
  264. [ 0.022819] [i2s] ecnt_i2s_drv_probe
  265. [ 0.022905]
  266. [ 0.022905] pbus_monitor init(ecnt_pbus_monitor_drv_probe) done
  267. [ 0.023556] workingset: timestamp_bits=14 max_order=17 bucket_order=3
  268. [ 0.028189] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  269. [ 0.028301] jffs2: version 2.2. (NAND) \C2 2001-2006 Red Hat, Inc.
  270. [ 0.057067] io scheduler mq-deadline registered
  271. [ 0.057074] io scheduler kyber registered
  272. [ 0.057956] [pwm]chip added
  273. [ 0.058110] PCIe driver version: 7552.1.20230912
  274. [ 0.058122] PCIe init.
  275. [ 0.058125] Iven check
  276. [ 0.058197] mtk-pcie 1fa90000.pcie: host bridge /pcie@1fa91000 ranges:
  277. [ 0.058213] mtk-pcie 1fa90000.pcie: MEM 0x20000000..0x23ffffff -> 0x20000000
  278. [ 0.058228]
  279. [ 0.058228] =====pcie_parse_port=11===base_num=0===port->reg_base=1fa90000===========
  280. [ 0.058228] =====pcie_parse_port=22==ecnt_pcie->mac0_base=e09f9000=0=========
  281. [ 0.058236]
  282. [ 0.058236] ========pcie_probe==before==0x1fa2018c=0===========
  283. [ 0.058236] ========pcie_probe==after==0x1fa2018c=7===========
  284. [ 0.058242]
  285. [ 0.058242] ===EN7552 PCIe init===
  286. [ 1.013290] mtk-pcie 1fa90000.pcie: pcie rc 0 linkup success
  287. [ 1.013300] mtk-pcie 1fa90000.pcie: set MEM trans window[0]: cpu_addr = 0x20000000, pci_addr = 0x20000000, size = 0x4000000
  288. [ 1.013307] mtk-pcie 1fa90000.pcie: ===ORIG pcie_mmio_ctrl 0
  289. [ 1.013313] mtk-pcie 1fa90000.pcie: ===after pcie_mmio_ctrl 1
  290. [ 1.013333]
  291. [ 1.013333] ====mtk_pcie_setup_irq=request_irq ERROR(-22)=====
  292. [ 1.013337]
  293. [ 1.013337] ===============PCIe check===tmp_reg=========81014c3===========
  294. [ 1.013429] mtk-pcie 1fa90000.pcie: PCI host bridge to bus 0000:00
  295. [ 1.013439] pci_bus 0000:00: root bus resource [bus 00-ff]
  296. [ 1.013446] pci_bus 0000:00: root bus resource [mem 0x20000000-0x23ffffff]
  297. [ 1.013475] pci 0000:00:00.0: [14c3:0810] type 01 class 0x060400
  298. [ 1.014335] PCI: bus0: Fast back to back transfers disabled
  299. [ 1.014344] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
  300. [ 1.014515] pci 0000:01:00.0: [14c3:7992] type 00 class 0x028000
  301. [ 1.014802] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
  302. [ 1.014909] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00007fff 64bit]
  303. [ 1.015676] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
  304. [ 1.015812] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 15.752 Gb/s with 8 GT/s x2 link)
  305. [ 1.016608] PCI: bus1: Fast back to back transfers disabled
  306. [ 1.016617] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
  307. [ 1.016638] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x202fffff]
  308. [ 1.016648] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x201fffff 64bit]
  309. [ 1.016734] pci 0000:01:00.0: BAR 2: assigned [mem 0x20200000-0x20207fff 64bit]
  310. [ 1.016819] pci 0000:00:00.0: PCI bridge to [bus 01]
  311. [ 1.016828] pci 0000:00:00.0: bridge window [mem 0x20000000-0x202fffff]
  312. [ 1.018861]
  313. [ 1.018861] mt7512_pcie_fixup: 0x1438 = 20000016
  314. [ 1.018861] mt7512_pcie_rc0_retrain: 80 = 0141dc23 80 = 01608c12
  315. [ 2.030912]
  316. [ 2.030912] RC0 Link Traing Result: 10120008
  317. [ 2.033916] ===EN7552 Pbus 0 for PCIe init===
  318. [ 2.033916] ========pcie_probe====0x1fbe3400=20000000===========
  319. [ 2.033916] ========pcie_probe====0x1fbe3404=ff000000===========
  320. [ 2.033916] ========pcie_probe====after pbus setting=======
  321. [ 2.033916] ========pcie_probe====0x1fbe3400=20000000===========
  322. [ 2.033916] ========pcie_probe====0x1fbe3404=ffc00000===========mtk-pcie 1fa92000.pcie: host bridge /pcie@1fa92000 ranges:
  323. [ 2.033998] mtk-pcie 1fa92000.pcie: MEM 0x24000000..0x27ffffff -> 0x24000000
  324. [ 2.034023]
  325. [ 2.034023] =====pcie_parse_port=11===base_num=1===port->reg_base=1fa92000===========
  326. [ 2.034023] =====pcie_parse_port=22==ecnt_pcie->mac0_base=e09f9000=e09fb000=========
  327. [ 2.034031]
  328. [ 2.034031] ========pcie_probe==before==0x1fa2018c=7===========
  329. [ 2.034031] ========pcie_probe==after==0x1fa2018c=7===========
  330. [ 2.034041] mtk-pcie 1fa92000.pcie: pcie rc 1 linkup success
  331. [ 2.034049] mtk-pcie 1fa92000.pcie: set MEM trans window[0]: cpu_addr = 0x24000000, pci_addr = 0x24000000, size = 0x4000000
  332. [ 2.034056] mtk-pcie 1fa92000.pcie: ===ORIG pcie_mmio_ctrl 0
  333. [ 2.034062] mtk-pcie 1fa92000.pcie: ===after pcie_mmio_ctrl 1
  334. [ 2.034077]
  335. [ 2.034077] ====mtk_pcie_setup_irq=request_irq ERROR(-22)=====
  336. [ 2.034082]
  337. [ 2.034082] ===============PCIe check===tmp_reg=========81114c3===========
  338. [ 2.034157] mtk-pcie 1fa92000.pcie: PCI host bridge to bus 0001:00
  339. [ 2.034165] pci_bus 0001:00: root bus resource [bus 00-ff]
  340. [ 2.034172] pci_bus 0001:00: root bus resource [mem 0x24000000-0x27ffffff]
  341. [ 2.034196] pci 0001:00:00.0: [14c3:0811] type 01 class 0x060400
  342. [ 2.035038] PCI: bus0: Fast back to back transfers disabled
  343. [ 2.035047] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
  344. [ 2.035215] pci 0001:01:00.0: [14c3:799a] type 00 class 0x028000
  345. [ 2.035501] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
  346. [ 2.035607] pci 0001:01:00.0: reg 0x18: [mem 0x00000000-0x00007fff 64bit]
  347. [ 2.036373] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
  348. [ 2.036508] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0001:00:00.0 (capable of 7.876 Gb/s with 8 GT/s x1 link)
  349. [ 2.037303] PCI: bus1: Fast back to back transfers disabled
  350. [ 2.037312] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01
  351. [ 2.037330] pci 0001:00:00.0: BAR 8: assigned [mem 0x24000000-0x242fffff]
  352. [ 2.037340] pci 0001:01:00.0: BAR 0: assigned [mem 0x24000000-0x241fffff 64bit]
  353. [ 2.037426] pci 0001:01:00.0: BAR 2: assigned [mem 0x24200000-0x24207fff 64bit]
  354. [ 2.037510] pci 0001:00:00.0: PCI bridge to [bus 01]
  355. [ 2.037519] pci 0001:00:00.0: bridge window [mem 0x24000000-0x242fffff]
  356. [ 2.039550]
  357. [ 2.039550] mt7512_pcie_fixup: 0x2438 = 24000016
  358. [ 2.039550] mt7512_pcie_rc1_retrain: 80 = 0141dc13 80 = 01608c12
  359. [ 3.051599]
  360. [ 3.051599] RC1 Link Traing Result: 10120008
  361. [ 3.054603] ===EN7552 Pbus 1 for PCIe init===
  362. [ 3.054603] ========pcie_probe====0x1fbe3408=21000000===========
  363. [ 3.054603] ========pcie_probe====0x1fbe340c=ff000000===========
  364. [ 3.054603] ========pcie_probe====after pbus setting=======
  365. [ 3.054603] ========pcie_probe====0x1fbe3408=24000000===========
  366. [ 3.054603] ========pcie_probe====0x1fbe340c=ffc00000===========ecnt_register_hook fail, pcie_api_hook already registered
  367. [ 3.054620] pcie ecnt_dev_fe_api_op register fail
  368. [ 3.055465] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
  369. [ 3.056077] printk: console [ttyS0] disabled
  370. [ 3.056123] 1fbf0000.serial: ttyS0 at MMIO 0x1fbf0000 (irq = 118, base_baud = 115200) is a 8250
  371. [ 4.311490] printk: console [ttyS0] enabled
  372. [ 4.315916] port 0 uart_register_driver fail!!
  373. [ 4.320380] ecnt-uart2: probe of 1fbf0300.serial failed with error -16
  374. [ 4.327072] data output always not ready
  375. [ 4.331205] airoha-trng 1faa1000.airoha-trng: [v1.01] registerd TRNG driver
  376. [ 4.338299] melinitsw: led-rtmodeG-gpios((ptrval)) found.
  377. [ 4.343718] melinitsw: btn-init-gpios((ptrval)) found.
  378. [ 4.348857] melinitsw: btn_aoss-gpios((ptrval)) found.
  379. [ 4.354003] melinitsw: sw_rtmode0-gpios((ptrval)) found.
  380. [ 4.359324] melinitsw: sw_rtmode1-gpios((ptrval)) found.
  381. [ 4.364638] melinitsw: led-diag-gpios((ptrval)) found.
  382. [ 4.369786] melinitsw: led-power-gpios((ptrval)) found.
  383. [ 4.375012] melinitsw: led-internetG-gpios((ptrval)) found.
  384. [ 4.380592] melinitsw: led-wirelessG-gpios((ptrval)) found.
  385. [ 4.386166] melinitsw: led-wirelessR-gpios((ptrval)) found.
  386. [ 4.391783] update_power_white_led_status: in
  387. [ 4.396133] update_power_white_led_status: out
  388. [ 4.400582] melinitsw: Create MELINITSW((ptrval)) Done.
  389. [ 4.405880] random: fast init done
  390. [ 4.409341] random: crng init done
  391. [ 4.417556] brd: module loaded
  392. [ 4.421034] IS_SPIFLASH=0x0, IS_NANDFLASH=0x1, (0xBFA10114)=0x6)
  393. [ 4.427052] spi_nand_probe: mfr_id=0xc8, dev_id=0x92
  394. [ 4.432218] Using Flash ECC.
  395. [ 4.435101] Detected SPI NAND Flash : _SPI_NAND_DEVICE_ID_GD5F2GM7UE, Flash Size=0x10000000
  396. [ 5.449303] Change mode_sw 01[ROUTER]
  397. [ 5.452964] ** MODE CHANGE->exec
  398. [ 5.452964] router
  399. [ 5.452964]
  400. [ 5.558058]
  401. [ 5.558058] Block: bad=0, total=2048, bad rate:(0 / 10000).
  402. [ 5.565104] spi nand flash
  403. [ 5.568072] libphy: Fixed MDIO Bus: probed
  404. [ 5.572175] PPP generic driver version 2.4.5
  405. [ 5.576492] PPP BSD Compression module registered
  406. [ 5.581200] PPP Deflate Compression module registered
  407. [ 5.586245] NET: Registered protocol family 24
  408. [ 5.590809] USB driver version: 7552.1.20230926
  409. [ 5.597337] port 1 u2_slew_rate_cal_7552
  410. [ 5.603263] FM_OUT value = 117(0x00000075)
  411. [ 5.608356] SR calibration value = 5
  412. [ 5.611928] port 2 u2_slew_rate_cal_7552
  413. [ 5.617847] FM_OUT value = 118(0x00000076)
  414. [ 5.622944] SR calibration value = 5
  415. [ 5.626513] USB PHY Init Complete
  416. [ 5.659321] AN7552 Initial Setting
  417. [ 5.662729] xhci-hcd 1fab0000.xhci: xHCI Host Controller
  418. [ 5.668050] xhci-hcd 1fab0000.xhci: new USB bus registered, assigned bus number 1
  419. [ 5.677181] xhci-hcd 1fab0000.xhci: irq 112, io mem 0x1fab0000
  420. [ 5.683387] hub 1-0:1.0: USB hub found
  421. [ 5.687158] hub 1-0:1.0: 2 ports detected
  422. [ 5.691427] xhci-hcd 1fab0000.xhci: xHCI Host Controller
  423. [ 5.696741] xhci-hcd 1fab0000.xhci: new USB bus registered, assigned bus number 2
  424. [ 5.704275] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
  425. [ 5.712650] hub 2-0:1.0: USB hub found
  426. [ 5.716417] hub 2-0:1.0: 1 port detected
  427. [ 5.720643] usbcore: registered new interface driver cdc_acm
  428. [ 5.726297] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
  429. [ 5.734352] usbcore: registered new interface driver usbserial_generic
  430. [ 5.740899] usbserial: USB Serial support registered for generic
  431. [ 5.746916] usbcore: registered new interface driver cypress_m8
  432. [ 5.752853] usbserial: USB Serial support registered for DeLorme Earthmate USB
  433. [ 5.760096] usbserial: USB Serial support registered for HID->COM RS232 Adapter
  434. [ 5.767411] usbserial: USB Serial support registered for Nokia CA-42 V2 Adapter
  435. [ 5.774743] usbcore: registered new interface driver ftdi_sio
  436. [ 5.780499] usbserial: USB Serial support registered for FTDI USB Serial Device
  437. [ 5.787911] i2c /dev entries driver
  438. [ 5.791634] airoha-i2c 1fbf8000.i2c: [v1.01] clock 100 kHz
  439. [ 5.797236] airoha-thermal_phy 1efbd000.thermal_phy: Thermal Sensor address probe start
  440. [ 5.805249] airoha-thermal_phy 1efbd000.thermal_phy: thermal driver version : 20231122
  441. [ 5.833186] airoha-thermal_phy 1efbd000.thermal_phy: This IC is calibrated
  442. [ 5.840064] airoha-thermal_phy 1efbd000.thermal_phy: EN7552 Init check code_30:23255 , Slope:5565
  443. [ 5.868974] airoha-thermal_phy 1efbd000.thermal_phy: Thermal Sensor address probe done
  444. [ 5.877182] airoha-wdt 1fbf0100.watchdog: Watchdog enabled (timeout=28 sec, nowayout=0)
  445. [ 5.887813] airoha-eip93 1fb70000.crypto_eip93: EIP93 Crypto Engine Initialized.
  446. [ 5.895322] hidraw: raw HID events driver (C) Jiri Kosina
  447. [ 5.900826] usbcore: registered new interface driver usbhid
  448. [ 5.906392] usbhid: USB HID core driver
  449. [ 5.910632] initail marking buffer allocated(cnt=1024)
  450. [ 5.915772] Bytecounter: allocated 64 tables
  451. [ 5.920052] nf_init_bytecounter: init finish.IPv4 over IPsec tunneling driver
  452. [ 5.927858] Initializing XFRM netlink socket
  453. [ 5.932516] NET: Registered protocol family 10
  454. [ 5.937619] Segment Routing with IPv6
  455. [ 5.941378] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
  456. [ 5.948025] ip6_tunnel: Create ip6_tunnel_fmr proc
  457. [ 5.952839] ip6_tunnel: Success
  458. [ 5.955980] NET: Registered protocol family 17
  459. [ 5.960444] NET: Registered protocol family 15
  460. [ 5.964943] Bridge firewalling registered
  461. [ 5.968951] 8021q: 802.1Q VLAN Support v1.8
  462. [ 5.973151] lib80211: common routines for IEEE802.11 drivers
  463. [ 5.978909] Registering SWP/SWPB emulation handler
  464. [ 5.984481]
  465. [ 5.984481] Airoha: flash device 0x02000000 at 0x00000000
  466. [ 5.991681] EN7512 mtd init: spi nand probe enter
  467. [ 5.996382] [spi_nand_setup] : Enter
  468. [ 6.000336] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0x92
  469. [ 6.006687] nand: ESMT _SPI_NAND_DEVICE_ID_GD5F2GM7UE
  470. [ 6.011741] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
  471. [ 6.019394] nand: NAND_ECC_NONE selected by board driver. This is not recommended!
  472. [ 6.026960] nand_scan_ident ok
  473. [ 6.030021] [spi_nand_setup]: chip size = 0x10000000, erase_shift=0x11
  474. [ 6.080585] bmt pool size: 163
  475. [ 6.084812] BMT & BBT Init Success
  476. [ 6.088352] Found 9 partitions in dtsi
  477. [ 6.092387] Creating 9 MTD partitions on "EN7512-SPI_NAND":
  478. [ 6.097959] 0x000000000000-0x000000080000 : "bootloader"
  479. [ 6.103826] 0x000000080000-0x000000100000 : "u-boot-env"
  480. [ 6.109608] 0x000000100000-0x000000500000 : "Factory"
  481. [ 6.115102] 0x000000500000-0x000000540000 : "ORGDATA"
  482. [ 6.120626] 0x000000540000-0x000005540000 : "tclinux"
  483. [ 7.002951] 2 fit-fw partitions found on MTD device tclinux
  484. [ 7.008523] 0x000000540000-0x000001da0000 : "kernel"
  485. [ 7.034079] 0x0000008545c8-0x000005540000 : "rootfs"
  486. [ 7.039042] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only
  487. [ 7.048945] 0x000005540000-0x00000a540000 : "tclinux_slave"
  488. [ 7.931750] 2 fit-fw partitions found on MTD device tclinux_slave
  489. [ 7.937846] 0x000005540000-0x000006da0000 : "kernel_slave"
  490. [ 7.943900] 0x0000058545c8-0x00000a540000 : "rootfs_slave"
  491. [ 7.949413] mtd: partition "rootfs_slave" doesn't start on an erase/write block boundary -- force read-only
  492. [ 7.959842] 0x00000a540000-0x00000af40000 : "syslog_data"
  493. [ 7.965686] 0x00000af40000-0x00000dc80000 : "user_property"
  494. [ 7.971826] 0x00000dc80000-0x00000e000000 : "art"
  495. [ 7.980836] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
  496. [ 7.988923] Freeing unused kernel memory: 1024K
  497. [ 8.009498] Run /sbin/init as init process
  498. init started: BusyBox v1.33.1 (2021-10-24 09:01:35 UTC)
  499. starting pid 92, tty '': '/bin/rc'
  500. start fw_recover.sh
  501. normal boot
  502. lib_mtk/librc.c(216) librc_platform_script :rc:***** load caldata *****
  503. lib_mtk/librc.c(217) librc_platform_script >> UNDER_CONSTRUCT!!1
  504. 1+0 records in
  505. 1+0 records out
  506. lib_mtk/librc.c(226) librc_platform_script :rc:***** copy drv configuration /etc/wireless *****
  507. lib_mtk/librc.c(107) create_fw_env_config :rc:uboot mtd1: 131072 131072
  508. lib_mtk/librc.c(248) librc_platform_script :rc:***** install module *****
  509. [ 9.573193] gpio_button_hotplug: loading out-of-tree module taints kernel.
  510. [ 9.619489] SCSI subsystem initialized
  511. [ 9.716540] warp_module_init(): module init and register callback for warp
  512. [ 9.723551] create warp_ctrl ok!!!
  513. [ 9.727007] wed_get_slot_map(): assign slot_id:0 for entry: 0!
  514. [ 9.732879] wed_get_slot_map(): assign slot_id:1 for entry: 1!
  515. [ 9.756103] module_sel: module license 'Proprietary' taints kernel.
  516. [ 9.762396] Disabling lock debugging due to kernel taint
  517. [ 9.768023] module_sel: unknown parameter 'Factory' ignored
  518. [ 9.773731] ecnt_register_cpu_interrupts
  519. [ 9.802267] legacy_api_initialized
  520. [ 9.809619] find led.conf error
  521. [ 9.812841] led path:/userfs/led.conf
  522. [ 9.874909] tccicmd V1.1.0.0 (2025:07:15-11:07:45)
  523. [ 9.881061] ERROR!Create /etc/fwTCver.conf fail!
  524. [ 9.888515]
  525. [ 9.888515] SIFMaster Wrapper init
  526. [ 9.893598]
  527. [ 9.893598] Register sifm cmd
  528. [ 9.955912] ECNT_HOOK_ERROR occur. ECNT_API_XPON_MODE_GET:215
  529. [ 10.060203] macType = 0
  530. [ 10.062652] flashQdmaInit = 0x11
  531. [ 10.087577] gpQdmaPriv->hwFwdBuffAddr = 0xdeaf0000, hwFwdBuffAddr = 0x9eaf0000
  532. [ 10.096282] tso_proc_init.
  533. [ 10.193742] copy NPU binary:/userfs/npu_rv32.bin(83748 Bytes) to 0xe0f00000
  534. [ 10.237471] copy NPU binary:/userfs/npu_data.bin(2740 Bytes) to 0xe0b80000
  535. [C0]core freq at 800 MHz
  536. [C0]timer_init: Timer clk is running at 200 Mhz
  537. [C0]Error: (core_id:7 >= 2) || (func_id:1 >= 8)
  538. [C0]np_skb_init(): SRAM is allocated to 3e83a4ac
  539. [C0]===========sync_method_init========
  540. [C0]timer_isr Store Value 10001[C0]tdma_tx_init L951 dscpBaseAddr=3e800000 reg:1e800000
  541. [C0]tdma_tx_init L951 dscpBaseAddr=3e800000 reg:1e800000
  542. [C0]tdma_set_tx_ring_to_int L109 :: ring:0 1fb50a2c=1010101 1fb50a28=0
  543. [C0]tdma_set_tx_ring_to_int L109 :: ring:1 1fb50a2c=2020202 1fb50a28=10
  544. [C0]tdma_tx_init L1010 INTR_TDMA_0 = 184 INTR_PPE_WIFI_BUF_ID = 95
  545. [C0]set AN7552 flow ctrl
  546. [C0][tdma_tx_init] PPE_WIFI_BUF_CFG=1fb50fe8, value=9c190110
  547. [C0]NPU init Version: 2.1.1-TLB7.3.283.3150-14
  548. [ 10.461117] counter_base[0]=e0a46fe8(1e838fe8)
  549. [ 10.465753] counter_base[1]=e0a49d40(1e838d40)
  550. [ 10.470397] counter_base[2]=e0a4b290(1e839290)
  551. [C0]wifi_mail_set_wait_npu_band0_on_cpu_wrapper L9649 not support on kite
  552. [ 10.481340] [npu_wifi_offload_get_pkt_buf_addr]npu_pkt_buf_addr=9b7b5000
  553. [C0]pkt_buf_addr=9b7b5000
  554. [ 10.490343] isForceToCpu=0
  555. [C0]isForceToCpu=false
  556. [ 10.576390] ether.c:v1.00-NAPI 29.Mar.2015
  557. [ 10.587555] eth0 (uninitialized): netif_napi_add() called with weight 128
  558. [ 10.594360] eth0: FE MAC Ethernet address: EC:5A:31:EC:85:80
  559. [ 10.602134] Use Internal switch ,type 10
  560. [ 10.645165] tcPhyVerLookUp 2903 400
  561. [ 10.648736] 7552 Ge,
  562. [ 10.651255] , port_num = 0, ephy_addr = 9, ephy_addr_base = 0x9
  563. [ 10.657355] [tcPhyInit] in [tcPhyInit] out , r31 = (9, 0x0)
  564. [ 10.669386] cha
  565. [ 11.171445] PHY=9 reg=0x1a value=0xaa PHY=9 reg=0x1a value=0xaa PHY=9 reg=0x1a value=0xab PHY=9 reg=0x1a value=0xaa
  566. [ 11.192098] GE Rext AnaCal Done! (2)(0x22)
  567. [ 11.197289] GE Rext AnaCal Done! (2)(0x22)
  568. [ 11.207776] GE R45 AnaCal zcal_idx(before table) (dec: 33) (hex: 0x21)
  569. [ 11.214653] GE R45 AnaCal Done! (cnt:1)(after table) ([7][6:0]:0x5c) ([6:0]:0xdc)
  570. [ 11.225882] GE R45 AnaCal zcal_idx(before table) (dec: 33) (hex: 0x21)
  571. [ 11.232752] GE R45 AnaCal Done! (cnt:1)(after table) ([7][6:0]:0x5c) ([6:0]:0xdc)
  572. [ 11.243982] GE R45 AnaCal zcal_idx(before table) (dec: 33) (hex: 0x21)
  573. [ 11.250851] GE R45 AnaCal Done! (cnt:1)(after table) ([7][6:0]:0x5c) ([6:0]:0xdc)
  574. [ 11.262075] GE R45 AnaCal zcal_idx(before table) (dec: 33) (hex: 0x21)
  575. [ 11.268945] GE R45 AnaCal Done! (cnt:1)(after table) ([7][6:0]:0x5c) ([6:0]:0xdc)
  576. [ 11.289369] GE Tx offset AnaCal Done! (4)(0x24)
  577. [ 11.296967] GE Tx offset AnaCal Done! (1)(0x1f)
  578. [ 11.304568] GE Tx offset AnaCal Done! (1)(0x1f)
  579. [ 11.312171] GE Tx offset AnaCal Done! (1)(0x1f)
  580. [ 11.328633] GE Tx amp AnaCal Done! (2) (0x22)
  581. [ 11.336719] GE Tx amp AnaCal Done! (1) (0x21)
  582. [ 11.357007] GE Tx amp AnaCal Done! (11) (0x2b)
  583. [ 11.371281] GE Tx amp AnaCal Done! (6) (0x26)
  584. [ 11.395703] port = 9
  585. [ 11.398057] 1e_12 = 0x8822 1e_16 = 0x8822 1e_17 = 0x2121 1e_18 = 0x2121 1e_19 = 0x2b2b 1e_20 = 0x2b2b 1e_21 = 0x2626 1e_22 = 0x2626
  586. [ 11.410062] 1e_174 = 0xdcdc 1e_175 = 0xdcdc
  587. [ 11.414413] 1e_12 = 0x3422 1e_16 = 0x8817 1e_17 = 0xe21 1e_18 = 0x2118 1e_19 = 0x172b 1e_20 = 0x2b21 1e_21 = 0x1026 1e_22 = 0x261a
  588. [ 11.426326] 1e_174 = 0xe3e4 1e_175 = 0xe6e6
  589. [ 11.433060] tcPhyVerLookUp 2903 400
  590. [ 11.436625] 7552 Ge,
  591. [ 11.439024] , port_num = 1, ephy_addr = 10, ephy_addr_base = 0x9
  592. [ 11.445198] [tcPhyInit] in [tcPhyInit] out , r31 = (10, 0x0)
  593. [ 11.457295] cha
  594. [ 11.959351] PHY=10 reg=0x1a value=0xa7 PHY=10 reg=0x1a value=0xa6 PHY=10 reg=0x1a value=0xa9 PHY=10 reg=0x1a value=0xa8
  595. [ 11.980181] GE R45 AnaCal zcal_idx(before table) (dec: 33) (hex: 0x21)
  596. [ 11.987052] GE R45 AnaCal Done! (cnt:1)(after table) ([7][6:0]:0x5c) ([6:0]:0xdc)
  597. [ 11.998279] GE R45 AnaCal zcal_idx(before table) (dec: 33) (hex: 0x21)
  598. [ 12.005157] GE R45 AnaCal Done! (cnt:1)(after table) ([7][6:0]:0x5c) ([6:0]:0xdc)
  599. [ 12.016385] GE R45 AnaCal zcal_idx(before table) (dec: 33) (hex: 0x21)
  600. [ 12.023255] GE R45 AnaCal Done! (cnt:1)(after table) ([7][6:0]:0x5c) ([6:0]:0xdc)
  601. [ 12.034484] GE R45 AnaCal zcal_idx(before table) (dec: 33) (hex: 0x21)
  602. [ 12.041354] GE R45 AnaCal Done! (cnt:1)(after table) ([7][6:0]:0x5c) ([6:0]:0xdc)
  603. [ 12.058357] GE Tx offset AnaCal Done! (1)(0x21)
  604. [ 12.065965] GE Tx offset AnaCal Done! (1)(0x1f)
  605. [ 12.076989] GE Tx offset AnaCal Done! (4)(0x24)
  606. [ 12.086873] GE Tx offset AnaCal Done! (3)(0x23)
  607. [ 12.110662] GE Tx amp AnaCal Done! (8) (0x28)
  608. [ 12.127285] GE Tx amp AnaCal Done! (8) (0x28)
  609. [ 12.146352] GE Tx amp AnaCal Done! (10) (0x2a)
  610. [ 12.163070] GE Tx amp AnaCal Done! (8) (0x28)
  611. [ 12.187493] port = 10
  612. [ 12.189937] 1e_12 = 0xa028 1e_16 = 0xa028 1e_17 = 0x2828 1e_18 = 0x2828 1e_19 = 0x2a2a 1e_20 = 0x2a2a 1e_21 = 0x2828 1e_22 = 0x2828
  613. [ 12.201935] 1e_174 = 0xdcdc 1e_175 = 0xdcdc
  614. [ 12.206288] 1e_12 = 0x5028 1e_16 = 0xa01e 1e_17 = 0x1628 1e_18 = 0x2920 1e_19 = 0x162a 1e_20 = 0x2a20 1e_21 = 0x1228 1e_22 = 0x281c
  615. [ 12.218288] 1e_174 = 0xe4e5 1e_175 = 0xe6e6
  616. [ 12.225021] tcPhyVerLookUp 2903 400
  617. [ 12.228587] 7552 Ge,
  618. [ 12.230991] , port_num = 2, ephy_addr = 11, ephy_addr_base = 0x9
  619. [ 12.237163] [tcPhyInit] in [tcPhyInit] out , r31 = (11, 0x0)
  620. [ 12.249266] cha
  621. [ 12.751327] PHY=11 reg=0x1a value=0xa8 PHY=11 reg=0x1a value=0xa8 PHY=11 reg=0x1a value=0xa9 PHY=11 reg=0x1a value=0xa6
  622. [ 12.772162] GE R45 AnaCal zcal_idx(before table) (dec: 33) (hex: 0x21)
  623. [ 12.779032] GE R45 AnaCal Done! (cnt:1)(after table) ([7][6:0]:0x5c) ([6:0]:0xdc)
  624. [ 12.790257] GE R45 AnaCal zcal_idx(before table) (dec: 33) (hex: 0x21)
  625. [ 12.797121] GE R45 AnaCal Done! (cnt:1)(after table) ([7][6:0]:0x5c) ([6:0]:0xdc)
  626. [ 12.808347] GE R45 AnaCal zcal_idx(before table) (dec: 33) (hex: 0x21)
  627. [ 12.815217] GE R45 AnaCal Done! (cnt:1)(after table) ([7][6:0]:0x5c) ([6:0]:0xdc)
  628. [ 12.826446] GE R45 AnaCal zcal_idx(before table) (dec: 33) (hex: 0x21)
  629. [ 12.833316] GE R45 AnaCal Done! (cnt:1)(after table) ([7][6:0]:0x5c) ([6:0]:0xdc)
  630. [ 12.850324] GE Tx offset AnaCal Done! (1)(0x21)
  631. [ 12.857922] GE Tx offset AnaCal Done! (1)(0x21)
  632. [ 12.865522] GE Tx offset AnaCal Done! (1)(0x1f)
  633. [ 12.873126] GE Tx offset AnaCal Done! (1)(0x1f)
  634. [ 12.893248] GE Tx amp AnaCal Done! (5) (0x25)
  635. [ 12.902552] GE Tx amp AnaCal Done! (2) (0x1e)
  636. [ 12.914297] GE Tx amp AnaCal Done! (4) (0x1c)
  637. [ 12.929701] GE Tx amp AnaCal Done! (7) (0x27)
  638. [ 12.954123] port = 11
  639. [ 12.956565] 1e_12 = 0x9425 1e_16 = 0x9425 1e_17 = 0x1e1e 1e_18 = 0x1e1e 1e_19 = 0x1c1c 1e_20 = 0x1c1c 1e_21 = 0x2727 1e_22 = 0x2727
  640. [ 12.968566] 1e_174 = 0xdcdc 1e_175 = 0xdcdc
  641. [ 12.972925] 1e_12 = 0x5025 1e_16 = 0x941e 1e_17 = 0xa1e 1e_18 = 0x1e14 1e_19 = 0x71c 1e_20 = 0x1c11 1e_21 = 0x1227 1e_22 = 0x271c
  642. [ 12.984755] 1e_174 = 0xe5e6 1e_175 = 0xe6e6
  643. [ 12.991489] tcPhyVerLookUp 2903 400
  644. [ 12.995054] 7552 Ge,
  645. [ 12.997453] , port_num = 3, ephy_addr = 12, ephy_addr_base = 0x9
  646. [ 13.003628] [tcPhyInit] in [tcPhyInit] out , r31 = (12, 0x0)
  647. [ 13.015723] cha
  648. [ 13.517780] PHY=12 reg=0x1a value=0xad PHY=12 reg=0x1a value=0xab PHY=12 reg=0x1a value=0xab PHY=12 reg=0x1a value=0xac
  649. [ 13.538614] GE R45 AnaCal zcal_idx(before table) (dec: 33) (hex: 0x21)
  650. [ 13.545487] GE R45 AnaCal Done! (cnt:1)(after table) ([7][6:0]:0x5c) ([6:0]:0xdc)
  651. [ 13.556716] GE R45 AnaCal zcal_idx(before table) (dec: 33) (hex: 0x21)
  652. [ 13.563586] GE R45 AnaCal Done! (cnt:1)(after table) ([7][6:0]:0x5c) ([6:0]:0xdc)
  653. [ 13.574814] GE R45 AnaCal zcal_idx(before table) (dec: 33) (hex: 0x21)
  654. [ 13.581684] GE R45 AnaCal Done! (cnt:1)(after table) ([7][6:0]:0x5c) ([6:0]:0xdc)
  655. [ 13.592913] GE R45 AnaCal zcal_idx(before table) (dec: 33) (hex: 0x21)
  656. [ 13.599783] GE R45 AnaCal Done! (cnt:1)(after table) ([7][6:0]:0x5c) ([6:0]:0xdc)
  657. [ 13.616787] GE Tx offset AnaCal Done! (1)(0x1f)
  658. [ 13.625533] GE Tx offset AnaCal Done! (2)(0x22)
  659. [ 13.633136] GE Tx offset AnaCal Done! (1)(0x1f)
  660. [ 13.641875] GE Tx offset AnaCal Done! (2)(0x22)
  661. [ 13.670542] GE Tx amp AnaCal Done! (12) (0x2c)
  662. [ 13.678711] GE Tx amp AnaCal Done! (1) (0x1f)
  663. [ 13.686797] GE Tx amp AnaCal Done! (1) (0x21)
  664. [ 13.702207] GE Tx amp AnaCal Done! (7) (0x27)
  665. [ 13.726632] port = 12
  666. [ 13.729074] 1e_12 = 0xb02c 1e_16 = 0xb02c 1e_17 = 0x1f1f 1e_18 = 0x1f1f 1e_19 = 0x2121 1e_20 = 0x2121 1e_21 = 0x2727 1e_22 = 0x2727
  667. [ 13.741077] 1e_174 = 0xdcdc 1e_175 = 0xdcdc
  668. [ 13.745429] 1e_12 = 0x642c 1e_16 = 0xb023 1e_17 = 0xe1f 1e_18 = 0x1f18 1e_19 = 0xf21 1e_20 = 0x2119 1e_21 = 0x1627 1e_22 = 0x2720
  669. [ 13.757255] 1e_174 = 0xe7e7 1e_175 = 0xe7e6
  670. [ 13.879491] macType = 0
  671. [ 13.881940] flashQdmaInit = 0x11
  672. [ 13.900691] gpQdmaPriv->hwFwdBuffAddr = 0xddaf0000, hwFwdBuffAddr = 0x9daf0000
  673. [ 13.909421] tso_proc_init.
  674. [ 13.931371] ecnt_swconfig: unknown parameter 'Factory' ignored
  675. [ 14.053108] Ralink HW NAT Module Enabled
  676. [ 14.057225] you need to modify struct FoeEntryExtKernel in soft_dma.h when you modifyied struct FoeEntryExt!SRAM_FOE_NUM=7, means PPE_FOE_NUM=512
  677. [ 14.070466] HWNAT Module enabled with Type:L2B/IPv4/IPv6/DS-LITE/6RD, foeSize:80B, sram_foeNum:512, dram_foeNum:16384
  678. [ 14.081078] hwnat_dram_idx_base = 16384
  679. [ 14.084967] IP check use Black List
  680. [ 14.091413] EN7523 PPE SRAM HW default setting is 512 at 64byte, no need to set by sw
  681. [ 14.099904] hnat roaming work enable
  682. [ 14.103476] fe resource init start v2
  683. [ 14.107205] fe resource init account & meter!
  684. [ 14.111650] 15 meter-2 id has been used, there is no left
  685. [ 14.117044] correct meter:2 idx range 0 : 14; real meter idx :127
  686. [ 14.123154] 15 meter-2 id has been used, there is no left
  687. [ 14.128544] correct meter:2 idx range 0 : 14; real meter idx :127
  688. [ 14.134684] isForceToCpu=0
  689. [C0]isForceToCpu=false
  690. [ 14.142570] 7581 GRE tunnel offload module init
  691. 7563 reset 8811
  692. 7563 reset KITE wifi (gpio6)
  693. reset KITE wifi done (gpio6)
  694. [ 15.201806] l2tp_offload: unknown parameter 'Factory' ignored
  695. [ 15.207697] 7581 L2TP VPN offload module init
  696. [ 15.225199] libphy: ARHT MDIO bus: probed
  697. Failed to find 8811_bbu_api. Maybe it is a [ 15.878407] use default setting, force mode an disable, phy_sel=0
  698. bu[ 15.884641] ae wan mac driver init
  699. ilt in module[ 15.889271] xsi_mac_api_logic_reset:817, error xfi_if_sts!
  700. ?
  701. [ 15.895890] ae wan mac driver init OK
  702. Failed to find nls_cp932. Maybe it is a built in module ?
  703. [ 15.921134] gre: GRE over IPv4 demultiplexor driver
  704. [ 15.929102] ip_gre: GRE over IPv4 tunneling driver
  705. [ 15.938151] ip6_gre: GRE over IPv6 tunneling driver
  706. [ 15.957850] Loading modules backported from Linux version v6.5-0-g2dde18cd1d8f
  707. [ 15.965132] Backport generated by backports.git v5.15.92-1-56-g5fb2ccb6b9e8
  708. [ 16.018130] mt_wifi_cmn: loaded
  709. [ 17.583978] [email protected],get_dbg_setting_by_profile() 920: debug level setting=INDEX0_debug_level not found!!
  710. [ 17.597235] [email protected],get_dbg_setting_by_profile() 947: debug option setting=INDEX0_debug_option not found!!
  711. [ 17.607498] physical_device_init!
  712. [ 17.610821] [email protected],bss_mngr_con_init() 3339: inited = 0
  713. [ 17.616749] [email protected],bss_idx_bitmap_init() 88: map_size=12
  714. [ 17.622758] [email protected],mld_grp_bitmap_init() 215: : map_size=12
  715. [ 17.629052] [email protected],bss_mngr_ext_entry_init() 3320: bss(64), grp(65)
  716. [ 17.636016] ser_mngr_init()[email protected],init_sta_mld_link_mgr() 3179: --->
  717. [ 18.242024]
  718. [ 18.242024] ========pcibios_map_irq === id=0, irq0=83, irq1=85 ===========pci 0000:00:00.0: enabling device (0140 -> 0142)
  719. [ 18.254628] mt7992 0000:01:00.0: enabling device (0140 -> 0142)
  720. [ 18.260651] mt7992 0000:01:00.0: Using 32bit DMA for streaming map
  721. [ 18.266828] mt7992 0000:01:00.0: Using 32bit DMA for coherent map
  722. [ 18.272921] mt7992 0000:01:00.0: connac_if_alloc_device()
  723. [ 18.278313] --> RTMPAllocAdapterBlock
  724. [ 18.283299]
  725. [ 18.283299]
  726. [ 18.283299] === pAd = 634f51f3, size = 3296424 ===
  727. [ 18.283299]
  728. [ 18.293561] <-- RTMPAllocAdapterBlock, Status=0
  729. [ 18.298106] mt7992 0000:01:00.0: connac_if_alloc_device(): hw:999a2d3c, priv:ea1c9c97, phy_size = 192
  730. [ 18.309035] mtk_mat_tb_init(): tb_size 64, mem_size 576
  731. [ 18.314540] mt7992_init_default()-->
  732. [ 18.318110] Use the default iPAiLNA bin image!
  733. [ 18.322567] <--mt7992_init_default()
  734. [ 18.326227] llget_profile_setting: dev_idx = 0!
  735. [ 18.330944] load l1profile succeed!
  736. [ 18.334463] BN0_profile_path: /etc/wireless/mediatek/mt7992.5040.b0.dat
  737. [ 18.341088] BN1_profile_path: /etc/wireless/mediatek/mt7992.5040.b1.dat
  738. [ 18.347708] E2pAccessMode=2
  739. [ 18.350620] TestModeEn=0
  740. [ 18.354928] entry_table_init: PD_GET_HW_WTBL_MAX(device)=544
  741. [ 18.363746] pause_bitmap_init: band_num=2, all_ac=68, per_ac=17, twt=17, pause=d55e9435, twt_pause=33befaa0
  742. [ 18.373503] pause[0]=5df11bf0
  743. [ 18.376461] twt_pause[0]=a4cc0ead
  744. [ 18.379776] pause[1]=c0691899
  745. [ 18.382738] twt_pause[1]=82641e3d
  746. [ 18.386048] physical_device_add_main_device: add physical device obj 4f5853de, device(=41ccb6d6), index(=0), chip=(0x7992)!
  747. [ 18.397189] mt7992 0000:01:00.0: connac_if_register_device_with_phy()
  748. [ 18.403695] [email protected],mtk_mac_hw_register() 2651: hw_dev(=41ccb6d6), chip=(0x7992), ad(=634f51f3), band_idx(=0)!
  749. [ 18.414405] physical_device_add_mac_adapter(): device(=41ccb6d6, index=0), mac_ad index(=0)!
  750. [ 18.422869] SKU: #2.MT7992-BE6500-7978-7979
  751. [ 18.428008] [email protected],RtmpRaDevCtrlInit() 2071: MCS_LUT not used because MacTb size(544) > 128!
  752. [ 18.437208] [email protected],CFG80211_SupBandInit() 738: 80211> RFICType= 7, NumOfChan= 108, ReInit = 0
  753. [ 18.446515] [email protected],CFG80211_SupBandInit() 741: 80211> Number of rate = 12
  754. [ 18.454356] [email protected],CFG80211_RegNotifier() 17563: crda> requlation requestion by core: [email protected],CFG80211_RegNotifier() 17597: 00
  755. [ 18.467062] [email protected],CFG80211_Register() 17504: 80211> end
  756. [ 18.473524] mt7992 0000:01:00.0: connac_if_alloc_phy()
  757. [ 18.478659] --> RTMPAllocAdapterBlock
  758. [ 18.483696]
  759. [ 18.483696]
  760. [ 18.483696] === pAd = 6626a1d5, size = 3296424 ===
  761. [ 18.483696]
  762. [ 18.493961] <-- RTMPAllocAdapterBlock, Status=0
  763. [ 18.498503] mt7992 0000:01:00.0: connac_if_alloc_phy(): hw:e64127d5, priv:70b0e6bf
  764. [ 18.506093] mt7992 0000:01:00.0: connac_if_register_device_with_phy()
  765. [ 18.512588] [email protected],mtk_mac_hw_register() 2651: hw_dev(=41ccb6d6), chip=(0x7992), ad(=6626a1d5), band_idx(=1)!
  766. [ 18.523317] physical_device_add_mac_adapter(): device(=41ccb6d6, index=0), mac_ad index(=1)!
  767. [ 18.531772] SKU: #2.MT7992-BE6500-7978-7979
  768. [ 18.536921] [email protected],RtmpRaDevCtrlInit() 2071: MCS_LUT not used because MacTb size(544) > 128!
  769. [ 18.546126] [email protected],CFG80211_SupBandInit() 738: 80211> RFICType= 7, NumOfChan= 108, ReInit = 0
  770. [ 18.555440] [email protected],CFG80211_SupBandInit() 741: 80211> Number of rate = 12
  771. [ 18.563292] [email protected],CFG80211_RegNotifier() 17563: crda> requlation requestion by core: [email protected],CFG80211_RegNotifier() 17597: 00
  772. [ 18.576036] [email protected],CFG80211_Register() 17504: 80211> end
  773. [ 18.582481] vendor: 14c3, device: 7992
  774. [ 18.586227] subvendor: ffffffff, subdevice: ffffffff
  775. [ 18.591196] class: 0, class_mask: 0
  776. [ 18.594683] driver_data : 00000000
  777. [ 18.602432]
  778. [ 18.602432] ========pcibios_map_irq === id=1, irq0=83, irq1=85 ===========pci 0001:00:00.0: enabling device (0140 -> 0142)
  779. [ 18.615024] mt799a 0001:01:00.0: enabling device (0140 -> 0142)
  780. [ 18.621044] mt799a 0001:01:00.0: Using 36bit DMA for streaming map
  781. [ 18.627218] mt799a 0001:01:00.0: Using 32bit DMA for coherent map
  782. [ 18.633616] mt7992 0000:01:00.0: get_rid_value(): get rid = 0
  783. [ 18.639361] mt7992 0000:01:00.0: set_rid_value(): set rid = 1
  784. [ 18.645105] mt799a 0001:01:00.0: get_rid_value(): get rid = 1
  785. [ 18.650851] vendor: 14c3, device: 799a
  786. [ 18.654595] subvendor: ffffffff, subdevice: ffffffff
  787. [ 18.659556] class: 0, class_mask: 0
  788. [ 18.663042] driver_data : 00000000
  789. [ 18.669491] GACT probability on
  790. [ 18.675676] Mirror/redirect action on
  791. [ 18.706959] u32 classifier
  792. [ 18.709685] input device check on
  793. [ 18.713345] Actions configured
  794. Failed to find sch_fq_codel. Maybe it is a built in module ?
  795. [ 18.751861] fuse: init (API version 7.31)
  796. [ 18.839023] initial /net/netfilter/nf_safety proc
  797. Failed to find crc-ccitt. Maybe it is a buil[ 18.939091] Protocol 47 is not namespace aware, cannot register.
  798. t i[ 18.945415] pptp init: can't register pptp_protocol
  799. n module ?
  800. failed to insert /lib/modules/5.4.55/pp[ 19.057501] xt_time: kernel timezone is -0000
  801. p_async.ko
  802. lib_mtk/librc.c(259) librc_platform_script :rc:*** install module Done ***
  803. lib_mtk/librc.c(262) librc_platform_script :rc:*** set wireless lower limit ***
  804. lib_mtk/wlctl-mtk.c(1215) wlctl_set_phy_lower_limit_all >> UNDER_CONSTRUCT!!1
  805. lib_mtk/librc.c(386) librc_platform_script >> UNDER_CONSTRUCT!!1
  806.  
  807. Please press Enter to activate this console. start fw_recover.sh
  808. normal boot
  809. 0 jp/JP -> enable
  810. 1 eng/ENG -> disable
  811. 2 de/LATIN1_DE -> disable
  812. 3 fr/LATIN1_FR -> disable
  813. 4 it/LATIN1_IT -> disable
  814. 5 es/LATIN1_ES -> disable
  815. 6 zh_cn/UTF8_ZHCN -> disable
  816. 7 zh_tw/U[ 19.304894] tmpr_watchd (233): /proc/233/oom_adj is deprecated, please use /proc/233/oom_score_adj instead.
  817. TF8_ZHTW -> disable
  818. 8 ko/UTF8_KO -> disable
  819. 9 ru/UTF8_RU -> disable
  820. 10 th/UTF8_TH -> disable
  821. 14 fi/UTF8_FI -> disable
  822. 16 sv/UTF8_SV -> disable
  823. 17 no/UTF8_NO -> disable
  824. 18 tr/UTF8_TR -> disable
  825. 19 br_pt/UTF8_BRPT -> disable
  826. [ 20.568613] ubi1: attaching mtd11
  827. [ 20.769544] ubi1: scanning is finished
  828. [ 20.780339] ubi1: attached mtd11 (name "user_property", size 45 MiB)
  829. [ 20.786690] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
  830. [ 20.793571] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
  831. [ 20.800360] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
  832. [ 20.807314] ubi1: good PEBs: 362, bad PEBs: 0, corrupted PEBs: 0
  833. [ 20.813316] ubi1: user volume: 2, internal volumes: 1, max. volumes count: 128
  834. [ 20.820540] ubi1: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 1625939037
  835. [ 20.829670] ubi1: available PEBs: 274, total reserved PEBs: 88, PEBs reserved for bad PEB handling: 35
  836. [ 20.838981] ubi1: background thread "ubi_bgt1d" started, PID 235
  837. UBI device number 1, total 362 LEBs (45965312 bytes, 43.8 MiB), available 274 LEBs (34791424 bytes, 33.1 MiB), LEB size 126976 bytes (124.0 KiB)
  838. Failed to find ubifs. Maybe it is a built in module ?
  839. [ 22.988146] UBIFS (ubi1:1): Mounting in unauthenticated mode
  840. [ 22.993927] UBIFS (ubi1:1): background thread "ubifs_bgt1_1" started, PID 242
  841. [ 23.028313] UBIFS (ubi1:1): recovery needed
  842. [ 23.077769] UBIFS (ubi1:1): recovery completed
  843. [ 23.082274] UBIFS (ubi1:1): UBIFS: mounted UBI device 1, volume 1, name "extra_property"
  844. [ 23.090367] UBIFS (ubi1:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
  845. [ 23.100280] UBIFS (ubi1:1): FS size: 4825088 bytes (4 MiB, 38 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
  846. [ 23.110372] UBIFS (ubi1:1): reserved for root: 227900 bytes (222 KiB)
  847. [ 23.116814] UBIFS (ubi1:1): media format: w5/r0 (latest is w5/r0), UUID 47260F74-5633-4B29-A06D-58F7DB0511BF, small LPT model
  848. main/wlconfig.c(3929) wlconf_load_devcaplist :XXX:[PID:00221]Initialize devcaplist
  849. 0 jp/JP -> enable
  850. 1 eng/ENG -> disable
  851. 2 de/LATIN1_DE -> disable
  852. 3 fr/LATIN1_FR -> disable
  853. 4 it/LATIN1_IT -> disable
  854. 5 es/LATIN1_ES -> disable
  855. 6 zh_cn/UTF8_ZHCN -> disable
  856. 7 zh_tw/UTF8_ZHTW -> disable
  857. 8 ko/UTF8_KO -> disable
  858. 9 ru/UTF8_RU -> disable
  859. 10 th/UTF8_TH -> disable
  860. 14 fi/UTF8_FI -> disable
  861. 16 sv/UTF8_SV -> disable
  862. 17 no/UTF8_NO -> disable
  863. 18 tr/UTF8_TR -> disable
  864. 19 br_pt/UTF8_BRPT -> disable
  865. Successfully initialized wpa_supplicant
  866. lib_mtk/wlctl-mtk.c(1280) Wireless_Insmod :wireless:symlink wireless.dat!!
  867. Failed to find et. Maybe it is a built in module ?
  868. Failed to find -L. Maybe it is a built in module ?
  869. Failed to find -L. Maybe it is a built in module ?
  870. Address not available
  871. ../common/rc_easymesh.c(112) VerifyParamsOfrc_easymesh :QQQ:CHECK PRIVATE_WIRELESS_DEFAULTSSID_NAME=Buffalo-BH-8580
  872. Address not available
  873. ../common/rc_easymesh.c(112) VerifyParamsOfrc_easymesh :QQQ:CHECK PRIVATE_WIRELESS_DEFAULTSSID_NAME=Buffalo-BH-8580
  874. 0 jp/JP -> enable
  875. 1 eng/ENG -> disable
  876. 2 de/LATIN1_DE -> disable
  877. 3 fr/LATIN1_FR -> disable
  878. 4 it/LATIN1_IT -> disable
  879. 5 es/LATIN1_ES -> disable
  880. 6 zh_cn/UTF8_ZHCN -> disable
  881. 7 zh_tw/UTF8_ZHTW -> disable
  882. 8 ko/UTF8_KO -> disable
  883. 9 ru/UTF8_RU -> disable
  884. 10 th/UTF8_TH -> disable
  885. 14 fi/UTF8_FI -> disable
  886. 16 sv/UTF8_SV -> disable
  887. 17 no/UTF8_NO -> disable
  888. 18 tr/UTF8_TR -> disable
  889. 19 br_pt/UTF8_BRPT -> disable
  890. lib_mtk/wlctl-mtk.c(1280) Wireless_Insmod :wireless:symlink wireless.dat!!
  891. Failed to find et. Maybe it is a built in module ?
  892. Failed to find -L. Maybe it is a built in module ?
  893. Failed to find -L. Maybe it is a built in module ?
  894. Change Mode exec
  895. router
  896.  
  897. ** SW MODE=router** SW MODE=routerFailed to find et. Maybe it is a built in module ?
  898. Ad[ 26.344990] netif_start_queue
  899. dress not available
  900. lib_mtk/wlctl-mtk.c(582) wlconf_preparation_for_platform :XXX:ENTER
  901. lib_mtk/wiredctl-mtk-airoha_en7563.c(344) SetEtherMdi >> UNDER_CONSTRUCT!!1
  902. [ 26.414116]
  903. [ 26.414116] advertising and autodetect_set(for switch) values decided as : 47 and 0
  904. set max age failed: Result[ 26.536892] add_if 00000000 ***************************
  905. not representable
  906. [ 26.544897] add_if 00000000 ***************************
  907. [ 26.552961] add_if 00000000 ***************************
  908. [ 26.563796] __inet_insert_ifa: addr C0A80B01
  909. [ 26.568387] __inet_insert_ifa: addr C0A80B01
  910. [ 26.573001] __inet_insert_ifa: addr C0A80B01
  911. device eth0.4 is not a slave of br0
  912. Address not available
  913. ../common/rc_wanctl6_dhcp6c.c(116) StartOfrc_wanctl6_dhcp6c :ipv6:Wanctl6Method = 5
  914. ../common/rc_wanctl6_dhcp6c.c(74) Set_IPv6RAConfig :ipv6:param eth0.4, 1[ 26.600606] Port 0 Link is Up - /Full
  915.  
  916. ,[ 26.604429] Port 5 Link is Up - /Full
  917. 1
  918.  
  919. ../common/rc_wanctl6_dhcp6c.c(78) Set_IPv6RAConfig :ipv6:param eth0.4, 1
  920. , 1
  921.  
  922. ../common/rc_wanctl6_dhcp6c.c(85) Set_IPv6RAConfig :ipv6:/proc/sys/net/ipv6/conf/eth0.4/accept_ra_defrtr = 1
  923.  
  924. ../common/rc_wanctl6_dhcp6c.c(89) Set_IPv6RAConfig :ipv6:/proc/sys/net/ipv6/conf/eth0.4/router_solicitations = 1
  925.  
  926. ../common/rc_wanctl6_dhcp6c.c(74) Set_IPv6RAConfig :ipv6:param all, 1
  927. , 1
  928.  
  929. ../common/rc_wanctl6_dhcp6c.c(78) Set_IPv6RAConfig :ipv6:param all, 1
  930. , 1
  931.  
  932. ../common/rc_wanctl6_dhcp6c.c(85) Set_IPv6RAConfig :ipv6:/proc/sys/net/ipv6/conf/all/accept_ra_defrtr = 1
  933.  
  934. ../common/rc_wanctl6_dhcp6c.c(89) Set_IPv6RAConfig :ipv6:/proc/sys/net/ipv6/conf/all/router_solicitations = 1
  935.  
  936. lib_mtk/wlctl-mtk.c(716) wlconf_preparation_for_platform :XXX:cmd=sed -i s/DfsSlaveEn=.*/DfsSlaveEn=0/ /etc/wireless/mediatek/mt7992.5040.b1.dat
  937. ipv6:auto_detect6 eth0.4
  938. ipv6:Modified IPv6-Status[DISCONNECT]ipv6:-- There is network disconnect --
  939. ipv6:start ALS2 (IPv6 prefix change detection) -> auto_detect restart!
  940. ipv6:[v6] auto_detect6[INITIALIZE]>[DISCONNECTED]
  941. lib_mtk/wlctl-mtk.c(732) wlconf_preparation_for_platform :XXX:cmd=sed -i s/no_bcn=.*/no_bcn=1;1;1;1;1;1;1;1/ /etc/wireless/mediatek/mt7992.5040.b1.dat
  942. lib_mtk/wlctl-mtk.c(814) wlconf_preparation_for_platform >> UNDER_CONSTRUCT!!1
  943. lib_mtk/wlctl-mtk.c(716) wlconf_preparation_for_platform :XXX:cmd=sed -i s/DfsSlaveEn=.*/DfsSlaveEn=0/ /etc/wireless/mediatek/mt7992.5040.b0.dat
  944. lib_mtk/wlctl-mtk.c(732) wlconf_preparation_for_platform :XXX:cmd=sed -i s/no_bcn=.*/no_bcn=1;1;1;1;1;1;1;1/ /etc/wireless/mediatek/mt7992.5040.b0.dat
  945. lib_mtk/wlctl-mtk.c(1280) Wireless_Insmod :wireless:symlink wireless.dat!!
  946. lib_mtk/wlctl-mtk.c(6551[ 27.048269] [email protected],mtk_cfg80211_vndr_set_acl_handler() 7289: pAd not start up. return!!
  947. ) wlconf_channel_set >> UNDER_CONSTRUCT!![ 27.060588] [email protected],mtk_cfg80211_vndr_set_acl_handler() 7289: pAd not start up. return!!
  948. 1
  949. Command failed: Invalid argument (-22)
  950. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra0 acl id=1 clear_all
  951. Command failed: Invalid argument (-22)
  952. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra0 acl id=1 policy=0
  953. Invalid arg: errno=19(No such device)
  954. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra2 acl id=1 clear_all
  955. Invalid arg: errno=19(No such device)
  956. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra2 acl id=1 policy=0
  957. Invalid arg: errno=19(No such device)
  958. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra4 acl id=1 clear_all[ 27.155547] [email protected],mtk_cfg80211_vndr_set_acl_handler() 7289: pAd not start up. return!!
  959.  
  960. lib_mtk/wlctl-mtk.c(6551) wlconf_chan[ 27.167677] [email protected],mtk_cfg80211_vndr_set_acl_handler() 7289: pAd not start up. return!!
  961. nel_set >> UNDER_CONSTRUCT!!1
  962. Command failed: Invalid argument (-22)
  963. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai0 acl id=1 clear_all
  964. Invalid arg: errno=19(No such device)
  965. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra4 acl id=1 policy=0
  966. Command failed: Invalid argument (-22)
  967. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai0 acl id=1 policy=0
  968. Invalid arg: errno=19(No such device)
  969. Invalid arg: errno=19(No such device)
  970. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai2 acl id=1 clear_alllib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:i[ 27.231299] [email protected],mtk_cfg80211_vndr_set_acl_handler() 7289: pAd not start up. return!!
  971. wpriv dev ra5 acl id=1 clear_all
  972.  
  973. Inv[ 27.243424] [email protected],mtk_cfg80211_vndr_set_acl_handler() 7289: pAd not start up. return!!
  974. alid arg: errno=19(No such device)
  975. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra5 acl id=1 policy=0
  976. Command failed: Invalid argument (-22)
  977. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra0 acl id=1 clear_all
  978. Command failed: Invalid argument (-22)
  979. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra0 acl id=1 policy=0
  980. Invalid arg: errno=19(No such device)
  981. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra7 acl id=1 clear_all
  982. Invalid arg: errno=19(No such device)
  983. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra7 acl id=1 policy=0
  984. Invalid arg: errno=19(No such device)
  985. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra7 acl id=1 clear_all
  986. Invalid arg: errno=19(No such device)
  987. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai2 acl id=1 policy=0
  988. Invalid arg: errno=19(No such device)
  989. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra7 acl id=1 policy=0
  990. Invalid arg: errno=19(No such device)
  991. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai4 acl id=1 clear_all
  992. Invalid arg: errno=19(No such device)
  993. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai4 acl id=1 policy=0
  994. Invalid arg: errno=19(No such device)
  995. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai5 acl id=1 clear_all
  996. Invalid arg: errno=19(No such device)
  997. [ 27.435740] [email protected],mtk_cfg80211_vndr_set_acl_handler() 7289: pAd not start up. return!!
  998. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mw[ 27.447749] [email protected],mtk_cfg80211_vndr_set_acl_handler() 7289: pAd not start up. return!!
  999. ctl_cmd :MWCTL:iwpriv dev rai5 acl id=1 policy=0
  1000. Command failed: Invalid argument (-22)
  1001. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai0 acl id=1 clear_all
  1002. Command failed: Invalid argument (-22)
  1003. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai0 acl id=1 policy=0
  1004. Invalid arg: errno=19(No such device)
  1005. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai7 acl id=1 clear_all
  1006. Invalid arg: errno=19(No such device)
  1007. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai7 acl id=1 policy=0
  1008. Invalid arg: errno=19(No such device)
  1009. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai7 acl id=1 clear_all
  1010. Invalid arg: errno=19(No such device)
  1011. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai7 acl id=1 policy=0
  1012. lib_mtk/wiredctl-mtk-airoha_en7563.c(460) SetQosPriorityUse >> UNDER_CONSTRUCT!!1
  1013. Invalid arg: errno=19(No such device)
  1014. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai6 set apmld=dellink
  1015. Invalid arg: errno=19(No such device)
  1016. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai6 set apmld=dellink
  1017. Invalid arg: errno=19(No such device)
  1018. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra6 set apmld=dellink
  1019. Invalid arg: errno=19(No such device)
  1020. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra6 set apmld=dellink
  1021. Invalid arg: errno=19(No such device)
  1022. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai7 set apmld=dellink
  1023. Invalid arg: errno=19(No such device)
  1024. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai7 set apmld=dellink
  1025. Invalid arg: errno=19(No such device)
  1026. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra7 set apmld=dellink
  1027. Invalid arg: errno=19(No such device)
  1028. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra7 set apmld=dellink
  1029. [ 28.143378] [email protected],mtk_cfg80211_vndr_set_handler() 4660: pAd not start up. return!!
  1030. Command failed: Bad address (-14)
  1031. l[ 28.154952] [email protected],mtk_cfg80211_vndr_set_handler() 4660: pAd not start up. return!!
  1032. ib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai0 set apmld=dellink
  1033. Command failed: Bad address (-14)
  1034. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai0 set apmld=dellink
  1035. [ 28.189232] [email protected],mtk_cfg80211_vndr_set_handler() 4660: pAd not start up. return!!
  1036. Command failed: Bad address (-14)
  1037. li[ 28.200810] [email protected],mtk_cfg80211_vndr_set_handler() 4660: pAd not start up. return!!
  1038. b_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra0 set apmld=dellink
  1039. Command failed: Bad address (-14)
  1040. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra0 set apmld=dellink
  1041. Invalid arg: errno=19(No such device)
  1042. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai7 set apmld=dellink
  1043. Invalid arg: errno=19(No such device)
  1044. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev rai7 set apmld=dellink
  1045. Invalid arg: errno=19(No such device)
  1046. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra7 set apmld=dellink
  1047. Invalid arg: errno=19(No such device)
  1048. lib_mtk/wlctl-mtk.c(462) wlctl_exec_mwctl_cmd :MWCTL:iwpriv dev ra7 set apmld=dellink
  1049. lib_mtk/wlctl-mtk.c(8904) wlctl_create_mld :XXX:usage[0/0x00200000] start...
  1050. lib_mtk/wlctl-mtk.c(9008) wlctl_create_mld :XXX:2g5g=0 2g6g=0 5g6g=0
  1051. lib_mtk/wlctl-mtk.c(8904) wlctl_create_mld :XXX:usage[1/0x00040000] start...
  1052. lib_mtk/wlctl-mtk.c(9008) wlctl_create_mld :XXX:2g5g=0 2g6g=0 5g6g=0
  1053. lib_mtk/wlctl-mtk.c(8904) wlctl_create_mld :XXX:usage[2/0x01000000] start...
  1054. lib_mtk/wlctl-mtk.c(9008) wlctl_create_mld :XXX:2g5g=0 2g6g=0 5g6g=0
  1055. lib_mtk/wlctl-mtk.c(8904) wlctl_create_mld :XXX:usage[3/0x02000000] start...
  1056. lib_mtk/wlctl-mtk.c(9008) wlctl_create_mld :XXX:2g5g=0 2g6g=0 5g6g=0
  1057. iptables: No chain/target/match by that name
  1058. iptables: No chain/target/match by that name
  1059. StartAutoDetectCommandMode(2334):ResetDetectStatus[JUDGE(4)]
  1060. StartAutoDetectCommandMode(2335):TRACE
  1061. SetStatusToAutoDetectModeFile(1072):RC Status:[JUDGE(4)](00000004)
  1062. StartAutoDetect(2271):ResetDetectStatus[UNLINK(1)]
  1063. StartAutoDetectCommandMode(2348):uNowStatus = [UNLINK(1)](00000001)
  1064. StartAutoDetectCommandMode(2498):TRACE
  1065. SetStatusToAutoDetectModeFile(1072):RC Status:[UNLINK(1)](00000001)
  1066. SetAutoDetectBridgeModeDetermine(2288):Check Bridge Mode Status [UNLINK(1)](00000001)
  1067. SetAutoDetectError(1101):Error:(00000002)
  1068. iptables: No chain/target/match by that name
  1069. iptables: No chain/target/match by that name
  1070. route: SIOCDELRT: No such process
  1071. Address not available
  1072. iptables: Bad rule (does a matching rule exist in that chain?)
  1073. ip6tables: No chain/target/match by that name
  1074. [NAPServ]nap_serv.c(244) nap_serv_main: pid: 666
  1075.  
  1076. [ 33.296225] xt_applicxation maclist: clean
  1077. iptables v1.4.2: Couldn't find target `UPNP-PREROUTING-CHAIN'
  1078.  
  1079. Try `iptables -h' or 'iptables --help' for more information.
  1080. iptables: No chain/target/match by that name
  1081. iptables: No chain/target/match by that name
  1082. iptables v1.4.2: Couldn't find target `UPNP-POSTROUTING-CHAIN'
  1083.  
  1084. Try `iptables -h' or 'iptables --help' for more information.
  1085. iptables: No chain/target/match by that name
  1086. iptables: No chain/target/match by that name
  1087. Unknown config line:insert_forward_rules = no
  1088. Unknown config line:upstream_bitrate = -1000000
  1089. Unknown config line:downstream_bitrate = -1000000
  1090. iptables: No chain/target/match by that name
  1091. iptables: No chain/target/match by that name
  1092. Address not available
  1093. Address not available
  1094. iptables: No chain/target/match by that name
  1095. iptables: No chain/target/match by that name
  1096. iptables: No chain/target/match by that name
  1097. Failed to find nf_conntrack_pptp. Maybe it is a built in module ?
  1098. Failed to find nf_nat_pptp. Maybe it is a built in module ?
  1099. net.netfilter.nf_conntrack_pptp_enable = 1
  1100. lib_mtk/wlctl-mtk.c(6529) wlconf_every_nas_down >> UNDER_CONSTRUCT!!1
  1101. lib_mtk/wlctl-mtk.c(6523) wlconf_every_nas_up >> UNDER_CONSTRUCT!!1
  1102. sh: /bin/set_clock.sh: not found
  1103. sh: /bin/led_psave.sh: not found
  1104. ML_SafeKill: try to kill 262
  1105. ML_SafeKill: took 600(msec) to kill 262[ 34.732639] update_power_white_led_status: in
  1106.  
  1107. [ 34.737127] update_power_white_led_status: out
  1108. module is not loaded
  1109. RTNETLINK answers: No such file or directory
  1110. killall: mproxyd: no process killed
  1111. ip6tables: No chain/target/match by that name
  1112. main.c(287) main :x:PMLIST RESTORE START
  1113. main.c(290) main :x:PMLIST RESTORE END
  1114. ntp.jst.mfeed.ad.jp: Try againARPING 192.168.11.1 from 192.168.11.1 br0
  1115. Sent 1 probe(s) (0 broadcast(s))
  1116. Received 0 response(s) (0 request(s), 0 broadcast(s))
  1117. StartAutoDetectRetryMode(3025):ResetDetectStatus[UNLINK(1)]
  1118. StartAutoDetectRetryMode(3036):uNowStatus = 00000001
  1119. StartAutoDetectRetryMode(3232):ResetDetectStatus[UNLINK(1)]
  1120. StartAutoDetectRetryMode(3255):TRACE
  1121. SetStatusToAutoDetectModeFile(1072):RETRY Status:[UNLINK(1)](00000001)
  1122. SetAutoDetectError(1101):Error:(00000002)
  1123. SetAutoDetectBridgeModeDetermine(2288):Check Bridge Mode Status [UNLINK(1)](00000001)
  1124.  
  1125. starting pid 222, tty '': '/bin/sh'
  1126.  
  1127.  
  1128. BusyBox v1.33.1 (2021-10-24 09:01:35 UTC) built-in shell (ash)
  1129.  
  1130. /bin/sh: can't access tty; job control turned off
  1131. / # uname -a
  1132. Linux APEC5A31EC8580 5.4.55 #0 SMP Sun Oct 24 09:01:35 2021 armv7l GNU/Linux
  1133. / # cat /proc/version
  1134. Linux version 5.4.55 ([email protected]) (gcc version 10.2.0 (OpenWrt GCC 10.2.0 r16325-88151b8303)) #0 SMP Sun Oct 24 09:01:35 2021
  1135. / # cat /proc/cmdline
  1136. sdram_conf=0x00108893 vendor_name=Buffalo inc. product_name=WSR3600BE4P ethaddr=ec:5a:31:ec:85:80 snmp_sysobjid=1.2.3.4.5 country_code=ff ether_gpio=0c power_gpio=1515 username=admin dsl_gpio=0b internet_gpio=02 multi_upgrade_gpio=0b020400000000000000000000000000 onu_type=2 qdma_init=11 root=/dev/mtdblock6 ro console=ttyS0,115200n8 earlycon bootflag=0 serdes_sel=0 serdes_pon=121 tclinux_info=0x185f24f,0x4aa8,0x30f8f7,0x314498,0x154c888
  1137. / # cat /proc/cpuinfo
  1138. processor : 0
  1139. model name : ARMv7 Processor rev 4 (v7l)
  1140. BogoMIPS : 50.00
  1141. Features : half thumb fastmult edsp tls idiva idivt lpae evtstrm crc32
  1142. CPU implementer : 0x41
  1143. CPU architecture: 7
  1144. CPU variant : 0x0
  1145. CPU part : 0xd03
  1146. CPU revision : 4
  1147.  
  1148. processor : 1
  1149. model name : ARMv7 Processor rev 4 (v7l)
  1150. BogoMIPS : 50.00
  1151. Features : half thumb fastmult edsp tls idiva idivt lpae evtstrm crc32
  1152. CPU implementer : 0x41
  1153. CPU architecture: 7
  1154. CPU variant : 0x0
  1155. CPU part : 0xd03
  1156. CPU revision : 4
  1157.  
  1158. Hardware : ECONET (Device Tree)
  1159. Revision : 0000
  1160. Serial : 0000000000000000
  1161. / # cat /proc/meminfo
  1162. MemTotal: 450888 kB
  1163. MemFree: 250108 kB
  1164. MemAvailable: 287556 kB
  1165. Buffers: 12448 kB
  1166. Cached: 34100 kB
  1167. SwapCached: 0 kB
  1168. Active: 29672 kB
  1169. Inactive: 20744 kB
  1170. Active(anon): 6536 kB
  1171. Inactive(anon): 0 kB
  1172. Active(file): 23136 kB
  1173. Inactive(file): 20744 kB
  1174. Unevictable: 2660 kB
  1175. Mlocked: 0 kB
  1176. HighTotal: 0 kB
  1177. HighFree: 0 kB
  1178. LowTotal: 450888 kB
  1179. LowFree: 250108 kB
  1180. SwapTotal: 0 kB
  1181. SwapFree: 0 kB
  1182. Dirty: 0 kB
  1183. Writeback: 0 kB
  1184. AnonPages: 6532 kB
  1185. Mapped: 5116 kB
  1186. Shmem: 4 kB
  1187. KReclaimable: 2376 kB
  1188. Slab: 106044 kB
  1189. SReclaimable: 2376 kB
  1190. SUnreclaim: 103668 kB
  1191. KernelStack: 1264 kB
  1192. PageTables: 648 kB
  1193. NFS_Unstable: 0 kB
  1194. Bounce: 0 kB
  1195. WritebackTmp: 0 kB
  1196. CommitLimit: 225444 kB
  1197. Committed_AS: 16764 kB
  1198. VmallocTotal: 507904 kB
  1199. VmallocUsed: 32280 kB
  1200. VmallocChunk: 0 kB
  1201. Percpu: 240 kB
  1202. / # cat /proc/mtd
  1203. dev: size erasesize name
  1204. mtd0: 00080000 00020000 "bootloader"
  1205. mtd1: 00080000 00020000 "u-boot-env"
  1206. mtd2: 00400000 00020000 "Factory"
  1207. mtd3: 00040000 00020000 "ORGDATA"
  1208. mtd4: 05000000 00020000 "tclinux"
  1209. mtd5: 01860000 00020000 "kernel"
  1210. mtd6: 04ceba38 00020000 "rootfs"
  1211. mtd7: 05000000 00020000 "tclinux_slave"
  1212. mtd8: 01860000 00020000 "kernel_slave"
  1213. mtd9: 04ceba38 00020000 "rootfs_slave"
  1214. mtd10: 00a00000 00020000 "syslog_data"
  1215. mtd11: 02d40000 00020000 "user_property"
  1216. mtd12: 00380000 00020000 "art"
  1217. mtd13: 0001f000 0001f000 "user_property_ubi"
  1218. mtd14: 005d0000 0001f000 "extra_property"
  1219. / # df -h
  1220. Filesystem Size Used Available Use% Mounted on
  1221. /dev/root 21.5M 21.5M 0 100% /
  1222. udev 220.2M 0 220.2M 0% /dev
  1223. ubi1!extra_property 3.6M 104.0K 3.3M 3% /mnt/ubi/ext_par
  1224. / # ls -la /sys/class/leds/
  1225. drwxr-xr-x 2 root root 0 Jun 30 15:07 .
  1226. drwxr-xr-x 34 root root 0 Jan 1 1970 ..
  1227. / # ls -la /sys/class/gpio/
  1228. drwxr-xr-x 2 root root 0 Jan 1 1970 .
  1229. drwxr-xr-x 34 root root 0 Jan 1 1970 ..
  1230. --w------- 1 root root 4096 Jan 1 1970 export
  1231. lrwxrwxrwx 1 root root 0 Jun 30 15:07 gpiochip0 -> ../../devices/platform/1fbf0204.gpio/gpio/gpiochip0
  1232. lrwxrwxrwx 1 root root 0 Jun 30 15:07 gpiochip32 -> ../../devices/platform/1fbf0270.gpio/gpio/gpiochip32
  1233. --w------- 1 root root 4096 Jan 1 1970 unexport
  1234. / # cat /sys/kernel/debug/gpio
  1235. gpiochip0: GPIOs 0-31, parent: platform/1fbf0204.gpio, 1fbf0204.gpio:
  1236. gpio-0 ( |btn-init ) in hi ACTIVE LOW
  1237. gpio-1 ( |led-power ) out lo ACTIVE LOW
  1238. gpio-4 ( |led-diag ) out hi ACTIVE LOW
  1239. gpio-5 ( |btn_aoss ) in hi ACTIVE LOW
  1240. gpio-7 ( |led-wirelessR ) out hi ACTIVE LOW
  1241. gpio-11 ( |led-internetG ) out hi ACTIVE LOW
  1242. gpio-12 ( |led-wirelessG ) out hi ACTIVE LOW
  1243. gpio-21 ( |led-rtmodeG ) out lo ACTIVE LOW
  1244. gpio-25 ( |sw_rtmode0 ) in lo
  1245. gpio-27 ( |sw_rtmode1 ) in hi
  1246.  
  1247. gpiochip1: GPIOs 32-63, parent: platform/1fbf0270.gpio, 1fbf0270.gpio:
  1248. / # ps
  1249. PID USER VSZ STAT COMMAND
  1250. 1 root 1172 S /sbin/init
  1251. 2 root 0 SW [kthreadd]
  1252. 3 root 0 IW< [rcu_gp]
  1253. 4 root 0 IW< [rcu_par_gp]
  1254. 5 root 0 IW [kworker/0:0-pm]
  1255. 6 root 0 IW< [kworker/0:0H-kb]
  1256. 7 root 0 IW [kworker/u4:0-ev]
  1257. 8 root 0 IW< [mm_percpu_wq]
  1258. 9 root 0 SW [ksoftirqd/0]
  1259. 10 root 0 IW [rcu_sched]
  1260. 11 root 0 SW [migration/0]
  1261. 12 root 0 SW [cpuhp/0]
  1262. 13 root 0 SW [cpuhp/1]
  1263. 14 root 0 SW [migration/1]
  1264. 15 root 0 SW [ksoftirqd/1]
  1265. 16 root 0 IW [kworker/1:0-rcu]
  1266. 17 root 0 IW< [kworker/1:0H-kb]
  1267. 18 root 0 IW< [netns]
  1268. 19 root 0 IW [kworker/0:1-eve]
  1269. 20 root 0 SW [reset_pcie_wifi]
  1270. 21 root 0 SW [oom_reaper]
  1271. 22 root 0 IW< [writeback]
  1272. 23 root 0 SW [kcompactd0]
  1273. 53 root 0 IW< [kblockd]
  1274. 54 root 0 IW< [blkcg_punt_bio]
  1275. 55 root 0 SW [watchdogd]
  1276. 56 root 0 SW [kswapd0]
  1277. 58 root 0 IW< [kthrotld]
  1278. 59 root 0 SW [hwrng]
  1279. 60 root 0 IW [kworker/1:1-eve]
  1280. 61 root 0 IW [kworker/u4:1-ev]
  1281. 63 root 0 SW [kworker/0:2+eve]
  1282. 87 root 0 IW< [ipv6_addrconf]
  1283. 90 root 0 IW< [kworker/0:1H-kb]
  1284. 91 root 0 IW< [kworker/1:1H-kb]
  1285. 122 root 0 IW [kworker/1:2-ipv]
  1286. 124 root 0 DW [dis_if]
  1287. 126 root 0 IW [kworker/0:3-rcu]
  1288. 154 root 0 IW< [cfg80211]
  1289. 157 root 0 SW [ser_mngr]
  1290. 221 root 7552 S /bin/rc
  1291. 222 root 1172 S /bin/sh
  1292. 233 root 7136 S tmpr_watchd
  1293. 235 root 0 SW [ubi_bgt1d]
  1294. 242 root 0 SW [ubifs_bgt1_1]
  1295. 251 root 5340 S hostapd -g /var/run/hostapd/global -P /var/run/hosta
  1296. 253 root 5352 S wpa_supplicant -n -B -g /var/run/wpa_supplicant/glob
  1297. 280 root 7136 S led_mgr
  1298. 284 root 7136 S modesw_mgr
  1299. 290 root 7136 S /bin/ircd
  1300. 294 root 7520 S /bin/syslogcached
  1301. 296 root 1172 S /bin/syslogd -s 64 -b 2
  1302. 305 root 7416 S /bin/nricd -config=/mnt/ubi/ext_par/nricd.conf
  1303. 308 root 1172 S /bin/klogd -c 5 -p WSR3600BE4P Ver.5.01 (R1.01/B1.2-
  1304. 324 root 7520 S /bin/backlog
  1305. 346 root 2804 S mini_httpd -t 600 -C /tmp/etc/httpd.conf
  1306. 370 root 7588 S auto_detect6 eth0.4 br0
  1307. 440 root 0 IW [kworker/u4:2]
  1308. 494 root 2904 S mini_httpd-ssl -t 600 -C /tmp/etc/httpdssl.conf
  1309. 495 root 0 IW [kworker/1:3-rcu]
  1310. 562 root 7136 S /bin/ap_servd -i br0
  1311. 563 root 7136 S /bin/ap_servd -i br0
  1312. 639 root 7136 S wanstate_check
  1313. 649 root 7136 S timerd fwup 86400
  1314. 655 root 7136 S wd_dnrd.sh dnrd -n --cache=off -i br0
  1315. 657 root 7136 S netwatchd
  1316. 658 root 7136 S wd_ntpclient.sh -o 86400 ntpclient -s -c 0 -i 86400
  1317. 660 root 960 S dnrd -n --cache=off -i br0
  1318. 661 root 768 S ntpclient -s -c 0 -i 86400 -h ntp.jst.mfeed.ad.jp
  1319. 666 root 7136 S /bin/nap_servd -i br0
  1320. 724 root 2336 S upnpd eth0.4 br0
  1321. 1138 root 7136 S auto_detect_retry 30
  1322. 1155 root 1172 R ps
  1323. / #
Tags: Router OpenWRT
Advertisement
Comments
  • User was banned
  • User was banned
  • User was banned
Add Comment
Please, Sign In to add comment
Public Pastes
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!