shitty pirate

HiZ>i
Bus Pirate v4
Community Firmware v7.1 - goo.gl/gCzQnW [HiZ 1-WIRE UART I2C SPI 2WIRE 3WIRE KEYB PIC DIO]
DEVID:0x1019 REVID:0x0004 (24FJ256GB106 UNK)
http://dangerousprototypes.com
HiZ>?
General                                 Protocol interaction
---------------------------------------------------------------------------
?       This help                       (0)     List current macros
=X/|X   Converts X/reverse X            (x)     Macro x
~       Selftest                        [       Start
o       Set output type                 ]       Stop
$       Jump to bootloader              {       Start with read
&/%     Delay 1 us/ms                   }       Stop
a/A/@   AUXPIN (low/HI/READ)            "abc"   Send string
b       Set baudrate                    123     Send integer value
c/C/k/K AUX assignment (A0/CS/A1/A2)    0x123   Send hex value
d/D     Measure ADC (once/CONT.)        0b110   Send binary value
f       Measure frequency               r       Read
g/S     Generate PWM/Servo              /       CLK hi
h       Commandhistory                  \       CLK lo
i       Versioninfo/statusinfo          ^       CLK tick
l/L     Bitorder (msb/LSB)              -       DAT hi
m       Change mode                     _       DAT lo
e       Set Pullup Method               .       DAT read
p/P     Pullup resistors (off/ON)       !       Bit read
s       Script engine                   :       Repeat e.g. r:10
v       Show volts/states               ;       Bits to read/write e.g. 0x55;2
w/W     PSU (off/ON)            <x>/<x= >/<0>   Usermacro x/assign x/list all
HiZ>v
Pinstates:
12.(Bk) 11.(Wt) 10.(Gy) 9.(Pu)  8.(Bu)  7.(Gn)  6.(Yw)  5.(Or)  4.(Rd)  3.(Br)  2.(Bk).(Wt)
GND     5.0V    3.3V    VPU     ADC     AUX2    AUX1    AUX     CS      MISO    CLK     MOSI
P       P       P       I       I       I       I       I       I       I       I       I
GND     0.00V   0.00V   0.00V   0.00V   L       L       L       L       L       L       L
HiZ>~
Disconnect any devices
Connect (ADC to +3.3V)
Space to continue
Ctrl
AUX OK
MODE LED OK
PULLUP H OK
PULLUP L OK
VREG OK
EEPROM
SCL OK
SDA OK
WP OK
READ&WRITE OK
ADC and supply
Vusb(5.03) OK
5V(4.98) OK
5V VPU(4.87) OK
ADC(0.00) FAIL
3.3V(3.29) OK
3.3V VPU(3.17) OK
Bus high
MOSI OK
CLK OK
MISO OK
CS OK
Bus Hi-Z 0
MOSI OK
CLK OK
MISO OK
CS OK
Bus Hi-Z 1
MOSI OK
CLK OK
MISO OK
CS OK
MODE, VREG, and USB LEDs should be on!
Any key to exit
Found 1 errors.
HiZ>?
General                                 Protocol interaction
---------------------------------------------------------------------------
?       This help                       (0)     List current macros
=X/|X   Converts X/reverse X            (x)     Macro x
~       Selftest                        [       Start
o       Set output type                 ]       Stop
$       Jump to bootloader              {       Start with read
&/%     Delay 1 us/ms                   }       Stop
a/A/@   AUXPIN (low/HI/READ)            "abc"   Send string
b       Set baudrate                    123     Send integer value
c/C/k/K AUX assignment (A0/CS/A1/A2)    0x123   Send hex value
d/D     Measure ADC (once/CONT.)        0b110   Send binary value
f       Measure frequency               r       Read
g/S     Generate PWM/Servo              /       CLK hi
h       Commandhistory                  \       CLK lo
i       Versioninfo/statusinfo          ^       CLK tick
l/L     Bitorder (msb/LSB)              -       DAT hi
m       Change mode                     _       DAT lo
e       Set Pullup Method               .       DAT read
p/P     Pullup resistors (off/ON)       !       Bit read
s       Script engine                   :       Repeat e.g. r:10
v       Show volts/states               ;       Bits to read/write e.g. 0x55;2
w/W     PSU (off/ON)            <x>/<x= >/<0>   Usermacro x/assign x/list all
HiZ>v
Pinstates:
12.(Bk) 11.(Wt) 10.(Gy) 9.(Pu)  8.(Bu)  7.(Gn)  6.(Yw)  5.(Or)  4.(Rd)  3.(Br)  2.(Bk).(Wt)
GND     5.0V    3.3V    VPU     ADC     AUX2    AUX1    AUX     CS      MISO    CLK     MOSI
P       P       P       I       I       I       I       I       I       I       I       I
GND     0.00V   0.00V   0.00V   0.00V   L       L       L       L       L       L       L