Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-148-generic] (local build)
- Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Model Family: Toshiba 3.5" DT01ACA... Desktop HDD
- Device Model: TOSHIBA DT01ACA300
- Serial Number: 56F61JGGS
- LU WWN Device Id: 5 000039 fe3d0d77a
- Firmware Version: MX6OABB0
- User Capacity: 3,000,592,982,016 bytes [3.00 TB]
- Sector Sizes: 512 bytes logical, 4096 bytes physical
- Rotation Rate: 7200 rpm
- Form Factor: 3.5 inches
- Device is: In smartctl database [for details use: -P show]
- ATA Version is: ATA8-ACS T13/1699-D revision 4
- SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
- Local Time is: Mon Jul 22 12:44:45 2019 CEST
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: FAILED!
- Drive failure expected in less than 24 hours. SAVE ALL DATA.
- See vendor-specific Attribute list for failed Attributes.
- General SMART Values:
- Offline data collection status: (0x84) Offline data collection activity
- was suspended by an interrupting command from host.
- Auto Offline Data Collection: Enabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: (21791) seconds.
- Offline data collection
- capabilities: (0x5b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- No Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 1) minutes.
- Extended self-test routine
- recommended polling time: ( 364) minutes.
- SCT capabilities: (0x003d) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
- 1 Raw_Read_Error_Rate 0x000b 099 099 016 Pre-fail Always - 131073
- 2 Throughput_Performance 0x0005 139 139 054 Pre-fail Offline - 72
- 3 Spin_Up_Time 0x0007 136 136 024 Pre-fail Always - 418 (Average 422)
- 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 18
- 5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 1982
- 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
- 8 Seek_Time_Performance 0x0005 124 124 020 Pre-fail Offline - 33
- 9 Power_On_Hours 0x0012 097 097 000 Old_age Always - 24168
- 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
- 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 18
- 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 487
- 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 487
- 194 Temperature_Celsius 0x0002 200 200 000 Old_age Always - 30 (Min/Max 22/36)
- 196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 3151
- 197 Current_Pending_Sector 0x0022 091 091 000 Old_age Always - 352
- 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
- 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
- SMART Error Log Version: 1
- ATA Error Count: 148 (device log contains only the most recent five errors)
- CR = Command Register [HEX]
- FR = Features Register [HEX]
- SC = Sector Count Register [HEX]
- SN = Sector Number Register [HEX]
- CL = Cylinder Low Register [HEX]
- CH = Cylinder High Register [HEX]
- DH = Device/Head Register [HEX]
- DC = Device Command Register [HEX]
- ER = Error register [HEX]
- ST = Status register [HEX]
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 148 occurred at disk power-on lifetime: 23273 hours (969 days + 17 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 02 80 92 0c 00 Error: UNC at LBA = 0x000c9280 = 823936
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 02 50 a0 92 0c 40 08 4d+22:42:11.406 READ FPDMA QUEUED
- 60 02 48 9e 92 0c 40 08 4d+22:42:11.406 READ FPDMA QUEUED
- 60 02 40 9c 92 0c 40 08 4d+22:42:11.406 READ FPDMA QUEUED
- 60 02 38 9a 92 0c 40 08 4d+22:42:11.406 READ FPDMA QUEUED
- 60 02 30 98 92 0c 40 08 4d+22:42:11.406 READ FPDMA QUEUED
- Error 147 occurred at disk power-on lifetime: 23273 hours (969 days + 17 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 02 22 92 0c 00 Error: UNC at LBA = 0x000c9222 = 823842
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 02 00 22 92 0c 40 08 4d+22:42:04.374 READ FPDMA QUEUED
- b0 d5 01 01 4f c2 00 08 4d+22:30:05.355 SMART READ LOG
- b0 d5 01 06 4f c2 00 08 4d+22:30:05.117 SMART READ LOG
- b0 d0 01 00 4f c2 00 08 4d+22:30:04.949 SMART READ DATA
- b0 da 00 00 4f c2 00 08 4d+22:30:04.749 SMART RETURN STATUS
- Error 146 occurred at disk power-on lifetime: 22963 hours (956 days + 19 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 d8 28 6d 11 07 Error: UNC 216 sectors at LBA = 0x07116d28 = 118582568
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 40 c0 6c 11 e0 08 3d+16:28:40.509 READ DMA EXT
- ef 10 02 00 00 00 a0 08 3d+16:28:40.509 SET FEATURES [Enable SATA feature]
- 27 00 00 00 00 00 e0 08 3d+16:28:40.509 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
- ec 00 00 00 00 00 a0 08 3d+16:28:40.507 IDENTIFY DEVICE
- ef 03 42 00 00 00 a0 08 3d+16:28:40.507 SET FEATURES [Set transfer mode]
- Error 145 occurred at disk power-on lifetime: 22833 hours (951 days + 9 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 20 c8 cf a0 01 Error: UNC 32 sectors at LBA = 0x01a0cfc8 = 27316168
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 58 90 cf a0 e0 08 4d+12:44:03.955 READ DMA EXT
- 25 00 20 e8 cc a0 e0 08 4d+12:43:53.837 READ DMA EXT
- c8 00 08 10 26 21 e0 08 4d+12:43:53.837 READ DMA
- 25 00 08 b0 34 b3 e0 08 4d+12:43:53.837 READ DMA EXT
- 25 00 08 d0 e6 b5 e0 08 4d+12:43:53.837 READ DMA EXT
- Error 144 occurred at disk power-on lifetime: 22833 hours (951 days + 9 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 08 f8 cf a0 01 Error: UNC 8 sectors at LBA = 0x01a0cff8 = 27316216
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 08 f8 cf a0 e0 08 4d+12:43:49.706 READ DMA EXT
- ef 10 02 00 00 00 a0 08 4d+12:43:49.698 SET FEATURES [Enable SATA feature]
- 27 00 00 00 00 00 e0 08 4d+12:43:49.698 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
- ec 00 00 00 00 00 a0 08 4d+12:43:49.696 IDENTIFY DEVICE
- ef 03 42 00 00 00 a0 08 4d+12:43:49.696 SET FEATURES [Set transfer mode]
- SMART Self-test log structure revision number 1
- Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
- # 1 Short offline Completed without error 00% 24157 -
- # 2 Extended offline Completed: read failure 90% 24109 2940734224
- # 3 Short offline Completed: read failure 90% 24085 1740891512
- # 4 Short offline Completed without error 00% 24062 -
- # 5 Short offline Completed: read failure 50% 24038 487376
- # 6 Short offline Completed: read failure 90% 24013 3610156344
- # 7 Short offline Completed without error 00% 23989 -
- # 8 Extended offline Completed: read failure 20% 23950 -
- # 9 Short offline Completed without error 00% 23917 -
- #10 Short offline Completed without error 00% 23893 -
- #11 Short offline Completed without error 00% 23869 -
- #12 Short offline Completed: read failure 90% 23845 4255860960
- #13 Short offline Completed without error 00% 23821 -
- #14 Extended offline Completed: read failure 10% 23782 -
- #15 Short offline Completed without error 00% 23749 -
- #16 Short offline Completed without error 00% 23725 -
- #17 Short offline Completed without error 00% 23701 -
- #18 Short offline Completed without error 00% 23677 -
- #19 Short offline Completed without error 00% 23653 -
- #20 Extended offline Completed without error 00% 23611 -
- #21 Short offline Completed without error 00% 23581 -
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement