SHOW:
|
|
- or go back to the newest paste.
| 1 | # you need soldering iron. delete R65 and solder it to R66 on motherboard. Picture from this : https://preview.redd.it/qpd8c7gq0dy91.jpg?width=616&format=pjpg&auto=webp&v=enabled&s=01fe06d3dbe97ca1d8b9f19999a3033cf41b98fb | |
| 2 | # | |
| 3 | [stepper_x] | |
| 4 | step_pin: PA5 | |
| 5 | dir_pin: PA4 | |
| 6 | enable_pin: !PC3 | |
| 7 | microsteps: 32 | |
| 8 | rotation_distance: 40 | |
| 9 | position_endstop: -38 | |
| 10 | position_min:-38 | |
| 11 | position_max: 229 | |
| 12 | homing_speed: 40 | |
| 13 | endstop_pin: tmc2209_stepper_x:virtual_endstop | |
| 14 | homing_retract_dist: 0 | |
| 15 | ||
| 16 | [tmc2209 stepper_x] | |
| 17 | uart_pin: PA15 | |
| 18 | #tx_pin: PA9 | |
| 19 | uart_address: 3 | |
| 20 | #select_pins: !PB4 | |
| 21 | diag_pin: ^PA6 | |
| 22 | driver_SGTHRS: 50 | |
| 23 | run_current: 0.6 | |
| 24 | stealthchop_threshold: 999999 | |
| 25 | interpolate: True | |
| 26 | ||
| 27 | [stepper_y] | |
| 28 | step_pin: PC4 | |
| 29 | dir_pin: PA7 | |
| 30 | enable_pin: !PC3 | |
| 31 | microsteps: 32 | |
| 32 | rotation_distance: 40 | |
| 33 | position_endstop: -4 #Needs adjustment, i have custom carriage | |
| 34 | position_min:-4 | |
| 35 | position_max: 229 | |
| 36 | homing_speed: 40 | |
| 37 | endstop_pin: tmc2209_stepper_y:virtual_endstop | |
| 38 | homing_retract_dist: 0 | |
| 39 | ||
| 40 | [tmc2209 stepper_y] | |
| 41 | uart_pin: PA15 | |
| 42 | #tx_pin: PA9 | |
| 43 | #select_pins: !PB4 | |
| 44 | uart_address: 1 | |
| 45 | run_current: 0.6 | |
| 46 | diag_pin: ^PC5 # Set to MCU pin connected to TMC DIAG pin | |
| 47 | driver_SGTHRS: 80 # 255 is most sensitive value, 0 is least sensitive | |
| 48 | stealthchop_threshold: 999999 | |
| 49 | ||
| 50 | [probe] | |
| 51 | pin: PB8 | |
| 52 | x_offset: 43.5 | |
| 53 | y_offset: 4.7 | |
| 54 | z_offset: 1.5 | |
| 55 | samples: 5 | |
| 56 | samples_result: average | |
| 57 | samples_tolerance: 0.05 | |
| 58 | samples_tolerance_retries: 5 | |
| 59 | sample_retract_dist: 0.5 | |
| 60 | speed:1 | |
| 61 | lift_speed:5 | |
| 62 | ||
| 63 | [stepper_z] | |
| 64 | step_pin: PC7 | |
| 65 | dir_pin: !PC6 | |
| 66 | enable_pin: !PC3 | |
| 67 | microsteps: 256 | |
| 68 | rotation_distance: 4 | |
| 69 | endstop_pin: probe:z_virtual_endstop | |
| 70 | #endstop_pin: PB8 | |
| 71 | #position_endstop: 1.35 | |
| 72 | position_min: -5 | |
| 73 | position_max: 230 | |
| 74 | homing_speed: 5 | |
| 75 | second_homing_speed:1 | |
| 76 | homing_retract_dist: 2.3 | |
| 77 | ||
| 78 | [tmc2209 stepper_z] | |
| 79 | uart_pin: PA15 | |
| 80 | #tx_pin: PA9 | |
| 81 | #select_pins: !PB4 | |
| 82 | uart_address: 2 | |
| 83 | run_current: 0.6 | |
| 84 | diag_pin: ^PA8 # Set to MCU pin connected to TMC DIAG pin | |
| 85 | driver_SGTHRS: 50 # 255 is most sensitive value, 0 is least sensitive | |
| 86 | stealthchop_threshold: 999999 | |
| 87 | ||
| 88 | [extruder] | |
| 89 | max_extrude_only_distance: 100.0 | |
| 90 | step_pin: PC14 | |
| 91 | dir_pin: PC15 | |
| 92 | enable_pin: !PC3 | |
| 93 | microsteps: 64 | |
| 94 | rotation_distance: 8.204 | |
| 95 | nozzle_diameter: 0.400 | |
| 96 | filament_diameter: 1.750 | |
| 97 | heater_pin: PA1 | |
| 98 | sensor_type: EPCOS 100K B57560G104F #Might need adjustment, i have new temp sensor along with V6 heatblock and heatbreak. | |
| 99 | sensor_pin: PC1 | |
| 100 | pressure_advance: 0.05 | |
| 101 | #control: pid | |
| 102 | # tuned for stock hardware with 200 degree Celsius target | |
| 103 | #pid_Kp: 21.527 | |
| 104 | #pid_Ki: 1.063 | |
| 105 | #pid_Kd: 108.982 | |
| 106 | min_temp: 0 | |
| 107 | min_extrude_temp: 0 | |
| 108 | max_temp: 300 #Stock is 250 | |
| 109 | ||
| 110 | [firmware_retraction] | |
| 111 | retract_length:0.5 #stock is more than 2 | |
| 112 | retract_speed:20 | |
| 113 | unretract_extra_length:0 | |
| 114 | unretract_speed:20 | |
| 115 | ||
| 116 | [tmc2208 extruder] | |
| 117 | uart_pin: PA15 | |
| 118 | run_current: 0.7 | |
| 119 | stealthchop_threshold: 999999 | |
| 120 | ||
| 121 | [heater_bed] | |
| 122 | heater_pin: PA0 | |
| 123 | sensor_type: EPCOS 100K B57560G104F | |
| 124 | sensor_pin: PC0 | |
| 125 | #control: pid | |
| 126 | # tuned for stock hardware with 50 degree Celsius target | |
| 127 | #pid_Kp: 54.027 | |
| 128 | #pid_Ki: 0.770 | |
| 129 | #pid_Kd: 948.182 | |
| 130 | min_temp: 0 | |
| 131 | max_temp: 130 | |
| 132 | ||
| 133 | [safe_z_home] | |
| 134 | home_xy_position: 70.5, 109.3 # Change coordinates to the center of your print bed | |
| 135 | speed: 50 | |
| 136 | z_hop: 5 # Move up 5mm | |
| 137 | z_hop_speed: 10 | |
| 138 | ||
| 139 | [bed_mesh] | |
| 140 | speed: 50 | |
| 141 | horizontal_move_z: 2 | |
| 142 | mesh_min: 19, 19 | |
| 143 | mesh_max: 210, 210 | |
| 144 | probe_count: 6, 6 | |
| 145 | ||
| 146 | [controller_fan controller_fan] | |
| 147 | pin: PA14 | |
| 148 | fan_speed: 0.7 | |
| 149 | ||
| 150 | [heater_fan extruder_fan] | |
| 151 | pin: PA13 | |
| 152 | heater_temp: 65.0 | |
| 153 | ||
| 154 | [fan] | |
| 155 | pin: PB9 | |
| 156 | ||
| 157 | [mcu] | |
| 158 | serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0 | |
| 159 | restart_method: command | |
| 160 | ||
| 161 | ||
| 162 | [printer] | |
| 163 | kinematics: cartesian | |
| 164 | max_velocity: 300 | |
| 165 | max_accel: 4000 | |
| 166 | max_z_velocity: 20 | |
| 167 | max_z_accel: 20 | |
| 168 | ||
| 169 | [virtual_sdcard] | |
| 170 | path: /home/orangepi/gcode_files |
