View difference between Paste ID: vyWWyptq and PwhkZTb0

-lines = {}
+lines = {}
-lines[1] = "BAD_FILE"
+lines[1] = "    ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:pio, hdd:pio"
-lines[2] = " "
+lines[2] = "ne2k-pci.c:v1.03 9/22/2003 D. Becker/P. Gortmaker"
-lines[3] = "ProOS была остановлена во избежания повреждения компьютера."
+lines[3] = "  http://www.scyld.com/network/ne2k-pci.html"
-lines[4] = "Если ошибка повторится, обратитесь к Programist135 за помощью."
+lines[4] = "hda: QEMU HARDDISK, ATA DISK drive"
-lines[5] = "Код ошибки: 0x000000BD"
+lines[5] = "ide0 at 0x170-0x177, 0x376 on irq 15"
-
+lines[6] = "hdc: QEMU CD-ROM, ATAPI CD/DVD-ROM drive"
-local com = require("component")
+lines[7] = "ide1 at 0x170-0x177, 0x376 on irq 15"
-local term = require("term")
+lines[8] = "ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10"
-local computer = require("computer")
+lines[9] = "ACPI: PCI Interrupt 0000:00:03:0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10"
-local event = require("event")
+lines[10] = "eth0: RealTek RTL-8029 found at 0xc100, IRQ 10, 52:54:00:12:34:56."
-local gpu = com.gpu
+lines[11] = "hda: max request size: 512KiB"
-
+lines[12] = "hda: 180224 sectors (92 MB) w/256KiB Cache, CHS=178/255/63, (U)DMA"
-gpu.setBackground(0x0000FF)
+lines[13] = "hda: set_multmode: status=0x41 { DriverReady Error }"
-term.clear()
+lines[14] = "hda: set_multmode: status=0x04 { DriverReady Error }"
-gpu.set(25, 1, "A fatal error has occured.")
+lines[15] = "ide: failed opcode wasL 0xef"
-term.setCursor(1, 3)
+lines[16] = "hda: cache flushes supported"
-for _, line in pairs(lines) do
+lines[17] = " hda: hda1"
-  print(line)
+lines[18] = "hdc: ATAPI 4X CD-ROM drive, 512kB Cache, (U)DMA"
-end
+lines[19] = "Uniform CD-ROM driver Revision: 3.20"
-gpu.set(25, 25, "Press any key to continue.")
+lines[20] = "Done."
-event.pull("key_down")
+lines[21] = "Begin: Mounting root file system... ..."
 lines[22] = "/init: /init: 151: Syntax error: 0xforce=panic"
 lines[23] = "Kernel panic - not syncing: Attempted to kill init!"
 lines[24] = " _"
 
 local com = require("component")
 local term = require("term")
 local computer = require("computer")
 local event = require("event")
 local gpu = com.gpu
 
 gpu.setBackground(0x000000)
 term.clear()
 term.setCursor(1, 3)
 for _, line in pairs(lines) do
   print(line)
 end
 event.pull("key_down")
 computer.shutdown(true)