View difference between Paste ID: pjpderRB and jtRFU6MB

-// Uncomment this line if you have any interrupts that are changing pins - this causes the library to be a little bit more cautious
+
-// #define FAST_SPI_INTERRUPTS_WRITE_PINS 1
+
 // How many leds in your strip?
-// Uncomment this line to force always using software, instead of hardware, SPI (why?)
+
-// #define FORCE_SOFTWARE_SPI 1
+
 // For led chips like Neopixels, which have a data line, ground, and power, you just
-// Uncomment this line if you want to talk to DMX controllers
+// need to define DATA_PIN.  For led chipsets that are SPI based (four wires - data, clock,
-// #define FASTSPI_USE_DMX_SIMPLE 1
+// ground, and power), like the LPD8806 define both DATA_PIN and CLOCK_PIN
 #define DATA_PIN 6
 #define CLOCK_PIN 8
 
 // Define the array of leds
 CRGB leds[NUM_LEDS];
 
 void setup() {
       // Uncomment/edit one of the following lines for your leds arrangement.
       // FastLED.addLeds<TM1803, DATA_PIN, RGB>(leds, NUM_LEDS);
       // FastLED.addLeds<TM1804, DATA_PIN, RGB>(leds, NUM_LEDS);
       // FastLED.addLeds<TM1809, DATA_PIN, RGB>(leds, NUM_LEDS);
       // FastLED.addLeds<WS2811, DATA_PIN, RGB>(leds, NUM_LEDS);
-void setup() {
+      // FastLED.addLeds<WS2812, DATA_PIN, RGB>(leds, NUM_LEDS);
-	// sanity check delay - allows reprogramming if accidently blowing power w/leds
+      // FastLED.addLeds<WS2812B, DATA_PIN, RGB>(leds, NUM_LEDS);
-   	delay(2000);
+      //  FastLED.addLeds<NEOPIXEL, DATA_PIN, RGB>(leds, NUM_LEDS);
       // FastLED.addLeds<UCS1903, DATA_PIN, RGB>(leds, NUM_LEDS);
-   	// For safety (to prevent too high of a power draw), the test case defaults to
+
-   	// setting brightness to 25% brightness
+      // FastLED.addLeds<WS2801, RGB>(leds, NUM_LEDS);
-   	LEDS.setBrightness(64);
+      // FastLED.addLeds<SM16716, RGB>(leds, NUM_LEDS);
-
+      // FastLED.addLeds<LPD8806, RGB>(leds, NUM_LEDS);
-   FastLED.addLeds<WS2801, DATA_PIN, CLOCK_PIN, RGB>(leds, NUM_LEDS);
+
        FastLED.addLeds<WS2801, DATA_PIN, CLOCK_PIN, RGB>(leds, NUM_LEDS);
-   	// LEDS.addLeds<WS2811, 13>(leds, NUM_LEDS);
+      // FastLED.addLeds<SM16716, DATA_PIN, CLOCK_PIN, RGB>(leds, NUM_LEDS);
-   	// LEDS.addLeds<TM1809, 13>(leds, NUM_LEDS);
+      // FastLED.addLeds<LPD8806, DATA_PIN, CLOCK_PIN, RGB>(leds, NUM_LEDS);
-   	// LEDS.addLeds<UCS1903, 13>(leds, NUM_LEDS);
+
-   	// LEDS.addLeds<TM1803, 13>(leds, NUM_LEDS);
+
 void loop() {
-   	// LEDS.addLeds<P9813>(leds, NUM_LEDS);
+
-   	//CLEDController *pLed = new ClocklessController_Trinket<4, NS(400), NS(400), NS(450), GRB>();
+
-   	//LEDS.addLeds(pLed, leds, NUM_LEDS);
+  for (int j=0; j< NUM_LEDS; j++){
-   	// LEDS.addLeds<LPD8806>(leds, NUM_LEDS);
+
-	// LEDS.addLeds<WS2801>(leds, NUM_LEDS);
+
-   	// LEDS.addLeds<SM16716>(leds, NUM_LEDS);
+
 for (int i=255;i>=0;i--){
-   	// LEDS.addLeds<WS2811, 11>(leds, NUM_LEDS);
+  for (int j=0; j< NUM_LEDS; j++){
     leds [j] = yourcolor.nscale8_video(i);
-	// Put ws2801 strip on the hardware SPI pins with a BGR ordering of rgb and limited to a 1Mhz data rate
+
-	// LEDS.addLeds<WS2801, 11, 13, BGR, DATA_RATE_MHZ(1)>(leds, NUM_LEDS);
+}}