SHOW:
|
|
- or go back to the newest paste.
| 1 | While waiting to compile drxvi314.ko from raw source, I loaded the alternative driver bcm_wimax as a test. | |
| 2 | ||
| 3 | After getting power to U600 via picocom and 'AT4GMODE=2' command 'dmseg -c|tail -45' the following is received: | |
| 4 | ||
| 5 | ||
| 6 | "usb 1-3.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 | |
| 7 | [ 6945.377764] usb 1-3.2: Product: U600 EVDO Modem | |
| 8 | [ 6945.377770] usb 1-3.2: Manufacturer: Franklin Wireless Corp. | |
| 9 | [ 6945.379700] cdc_acm 1-3.2:1.0: ttyACM0: USB ACM device | |
| 10 | [ 6945.580919] usbcore: registered new interface driver qcaux | |
| 11 | [ 6945.583450] usbserial: USB Serial support registered for qcaux | |
| 12 | [ 6945.583502] qcaux 1-3.2:1.2: qcaux converter detected | |
| 13 | [ 6945.587715] usb 1-3.2: qcaux converter now attached to ttyUSB0 | |
| 14 | [ 6945.588841] qcaux 1-3.2:1.3: qcaux converter detected | |
| 15 | [ 6945.589263] usb 1-3.2: qcaux converter now attached to ttyUSB1 | |
| 16 | [ 6945.592364] qcaux 1-3.2:1.4: qcaux converter detected | |
| 17 | [ 6945.592735] usb 1-3.2: qcaux converter now attached to ttyUSB2 | |
| 18 | [ 6945.592783] qcaux 1-3.2:1.5: qcaux converter detected | |
| 19 | [ 6945.593062] usb 1-3.2: qcaux converter now attached to ttyUSB3 | |
| 20 | [ 7006.108244] usb 1-3.1: new high-speed USB device number 7 using ehci-pci | |
| 21 | [ 7006.201093] usb 1-3.1: New USB device found, idVendor=198f, idProduct=0220 | |
| 22 | [ 7006.201104] usb 1-3.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 | |
| 23 | [ 7006.201110] usb 1-3.1: Product: BCSM250 Mobile WiMAX | |
| 24 | [ 7006.201116] usb 1-3.1: Manufacturer: Beceem Communications | |
| 25 | [ 7006.201122] usb 1-3.1: SerialNumber: SCG9001305 | |
| 26 | [ 7006.202593] usbbcm_device_probe:subtype[1] = 0x000000ff | |
| 27 | [ 7006.202603] usbbcm_device_probe:subtype[2] = 0x00000000 | |
| 28 | [ 7006.202607] usbbcm_device_probe:subtype[4] = 0x00000000 | |
| 29 | [ 7006.202611] usbbcm_device_probe:subtype[8] = 0x00000000 | |
| 30 | [ 7006.202616] InitAdapter:Initialising Adapter = f2da0500 | |
| 31 | [ 7006.202679] InitAdapter:Adapter initialised<7>[ 7006.202688] usbbcm_device_probe:psIntfAdapter 0xf1c08000 | |
| 32 | [ 7006.202860] usb 1-3.1: RDM Chip ID 0xbece3301 | |
| 33 | [ 7006.216863] beceem: AutoSyncup is Disabled | |
| 34 | [ 7006.216873] beceem: Disabling autolink up | |
| 35 | [ 7006.216877] beceem: DDR Setting: 3 | |
| 36 | [ 7006.216881] beceem: Power Save Mode: 0 | |
| 37 | [ 7006.216884] beceem: Enabling Auto Firmware Download | |
| 38 | [ 7006.216888] beceem: MIPSConfig : 0x0 | |
| 39 | [ 7006.216891] beceem: PMU MODE: 0 | |
| 40 | [ 7006.216894] beceem: uiEEPROMFlag : 0x2 | |
| 41 | [ 7006.217466] reset_card_proc:Resetting UMA-B | |
| 42 | [ 7006.292222] usb 1-3.1: reset high-speed USB device number 7 using ehci-pci | |
| 43 | [ 7006.407049] ddr_init:Register Count is =48 | |
| 44 | - | [ 7006.433508] usbbcm 1-3.1:1.0: beceem eth1: register usb-0000:00:1d.7-3.1 f4:63:49:07:27:9d |
| 44 | + | [ 7006.433508] usbbcm 1-3.1:1.0: beceem eth1: register usb-0000:00:1d.7-3.1 f4:63:49:xx:xx:xx |
| 45 | [ 7006.487970] BcmFileDownload:Opened file is = /lib/firmware/macxvi200.bin and length =0x2084a0 to be downloaded at =0xbfc00000 | |
| 46 | [ 7006.487980] BcmFileDownload:download start ccfcc232InterfaceFileDownload:Got end of file! <------- | |
| 47 | [ 7007.245536] InterfaceFileReadbackFromChip:Got end of file!<6>[ 7007.614627] beceem eth1: enabling interface | |
| 48 | [ 7007.615144] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready | |
| 49 | [ 7007.638462] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready | |
| 50 | [ 7007.719708] beceem eth1: disabling interface" | |
| 51 | ||
| 52 | The driver qcaux is for diagnosis, etc. as far as I know. | |
| 53 | ||
| 54 | <------- marks where I think a problem is. "End of file." | |
| 55 | Is it read from the chip as indicated? | |
| 56 | If yes, how to correct it? | |
| 57 | ||
| 58 | - | Another bunch of questions. |
| 58 | + | Another bunch of questions. |
| 59 | ||
| 60 | But: | |
| 61 | ||
| 62 | ifconfig -a: | |
| 63 | ||
| 64 | eth1 Link encap:Ethernet HWaddr f4:63:49:xx:xx:xx | |
| 65 | BROADCAST NOARP MULTICAST MTU:1400 Metric:1 | |
| 66 | RX packets:0 errors:0 dropped:0 overruns:0 frame:0 | |
| 67 | TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 | |
| 68 | collisions:0 txqueuelen:5 | |
| 69 | RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) | |
| 70 | ||
| 71 | Network Manager shows a new Broadband Connection called 'unmanaged' Networking Interface. | |
| 72 | Connection state: Unmanaged | |
| 73 | IP address: No IP address | |
| 74 | system name: eth1 |
