SHOW:
|
|
- or go back to the newest paste.
| 1 | - | Here below is dmesg after command "modprobe bcm4330". That command gives an error saying something like bcm4330 received the wrong parameters... |
| 1 | + | [ 2.610260] [wifi]: Select sdio wifi: bcm40183 !! |
| 2 | - | |
| 2 | + | [ 2.618728] [mmc_pm]: SDIO card gpio init is OK !! |
| 3 | - | [ 7335.247430] Config Error: not for huawei mw269x sdio wifi module |
| 3 | + | [ 2.625529] [mmc]: sunximmc_init |
| 4 | - | [ 7335.259312] [bcm40183]: No gpio hw_mw269x_wl_enb for BCM40183 module |
| 4 | + | [ 2.633335] [mmc]: sunxi mmc controller using config : 0xb |
| 5 | - | [ 7335.268788] [mmc]: mmc 3 power on !! |
| 5 | + | [ 2.643804] [mmc]: sunxi-mmc.0: pdev->name: sunxi-mmc, pdev->id: 0 |
| 6 | - | [ 7335.279079] [DHD] |
| 6 | + | [ 2.652780] [mmc]: mmc 0 power off !! |
| 7 | - | [ 7335.279093] Dongle Host Driver, version 5.90.125.69 |
| 7 | + | [ 2.664102] [mmc]: mmc0 Probe: base:0xf1c0f000 irq:32 dma:0 pdes:0xee80c000, ret 0. |
| 8 | - | [ 7335.325972] [mmc]: sdxc_request_done(L1118): smc 3 err, cmd 52, RTO !! |
| 8 | + | [ 2.676803] [mmc]: sunxi-mmc.1: pdev->name: sunxi-mmc, pdev->id: 1 |
| 9 | - | [ 7335.339383] [mmc]: sdxc_request_done(L1118): smc 3 err, cmd 52, RTO !! |
| 9 | + | [ 2.685780] [mmc]: mmc 1 power off !! |
| 10 | - | [ 7335.356006] [mmc]: sdxc_request_done(L1118): smc 3 err, cmd 8, RTO !! |
| 10 | + | [ 2.696958] [mmc]: mmc1 Probe: base:0xf1c10000 irq:33 dma:0 pdes:0xee834000, ret 0. |
| 11 | - | [ 7335.368797] [mmc]: sdxc_request_done(L1118): smc 3 err, cmd 5, RTO !! |
| 11 | + | [ 2.709555] [mmc]: sunxi-mmc.3: pdev->name: sunxi-mmc, pdev->id: 3 |
| 12 | - | [ 7335.382405] [mmc]: sdxc_request_done(L1118): smc 3 err, cmd 5, RTO !! |
| 12 | + | [ 2.718483] [mmc]: mmc 3 power off !! |
| 13 | - | [ 7335.395033] [mmc]: sdxc_request_done(L1118): smc 3 err, cmd 5, RTO !! |
| 13 | + | [ 2.729649] [mmc]: mmc3 Probe: base:0xf1c12000 irq:35 dma:0 pdes:0xee838000, ret 0. |
