API tools faq
paste
Advertisement
Guest User

Untitled

a guest
Apr 18th, 2017
548
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 29.70 KB | None | 0 0
raw download clone embed print report
  1. # Smoothieboard configuration file, see http://smoothieware.org/configuring-smoothie
  2. # NOTE Lines must not exceed 132 characters, and '#' characters mean what follows is ignored
  3. ## Robot module configurations : general handling of movement G-codes and slicing into moves
  4.  
  5. # Basic motion configuration
  6. default_feed_rate 4000 # Default speed (mm/minute) for G1/G2/G3 moves
  7. default_seek_rate 4000 # Default speed (mm/minute) for G0 moves
  8. mm_per_arc_segment 0.0 # Fixed length for line segments that divide arcs, 0 to disable
  9. #mm_per_line_segment 5 # Cut lines into segments this size
  10. mm_max_arc_error 0.01 # The maximum error for line segments that divide arcs 0 to disable
  11. # note it is invalid for both the above be 0
  12. # if both are used, will use largest segment length based on radius
  13.  
  14. # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
  15. # See http://smoothieware.org/stepper-motors
  16. alpha_steps_per_mm 157.575 # Steps per mm for alpha ( X ) stepper
  17. beta_steps_per_mm 157.575 # Steps per mm for beta ( Y ) stepper
  18. gamma_steps_per_mm 1600 # Steps per mm for gamma ( Z ) stepper
  19.  
  20. # Planner module configuration : Look-ahead and acceleration configuration
  21. # See http://smoothieware.org/motion-control
  22. acceleration 3000 # Acceleration in mm/second/second.
  23. #z_acceleration 500 # Acceleration for Z only moves in mm/s^2, 0 uses acceleration which is the default. DO NOT SET ON A DELTA
  24. junction_deviation 0.05 # See http://smoothieware.org/motion-control#junction-deviation
  25. #z_junction_deviation 0.0 # For Z only moves, -1 uses junction_deviation, zero disables junction_deviation on z moves DO NOT SET ON A DELTA
  26.  
  27. # Cartesian axis speed limits
  28. x_axis_max_speed 30000 # Maximum speed in mm/min
  29. y_axis_max_speed 30000 # Maximum speed in mm/min
  30. z_axis_max_speed 300 # Maximum speed in mm/min
  31.  
  32. # Stepper module configuration
  33. # Pins are defined as ports, and pin numbers, appending "!" to the number will invert a pin
  34. # See http://smoothieware.org/pin-configuration and http://smoothieware.org/pinout
  35. alpha_step_pin 2.0 # Pin for alpha stepper step signal
  36. alpha_dir_pin 0.5! # Pin for alpha stepper direction, add '!' to reverse direction
  37. alpha_en_pin 0.4 # Pin for alpha enable pin
  38. alpha_current 1.5 # X stepper motor current
  39. alpha_max_rate 30000.0 # Maximum rate in mm/min
  40.  
  41. beta_step_pin 2.1 # Pin for beta stepper step signal
  42. beta_dir_pin 0.11! # Pin for beta stepper direction, add '!' to reverse direction
  43. beta_en_pin 0.10 # Pin for beta enable
  44. beta_current 1.5 # Y stepper motor current
  45. beta_max_rate 30000.0 # Maxmimum rate in mm/min
  46.  
  47. gamma_step_pin 2.2 # Pin for gamma stepper step signal
  48. gamma_dir_pin 0.20 # Pin for gamma stepper direction, add '!' to reverse direction
  49. gamma_en_pin 0.19 # Pin for gamma enable
  50. gamma_current 1.5 # Z stepper motor current
  51. gamma_max_rate 300.0 # Maximum rate in mm/min
  52.  
  53. # A axis
  54. delta_steps_per_mm 100 # may be steps per degree for example
  55. delta_step_pin 2.3 # Pin for delta stepper step signal
  56. delta_dir_pin 0.22 # Pin for delta stepper direction
  57. delta_en_pin 0.21 # Pin for delta enable
  58. delta_current 1.5 # Z stepper motor current
  59. delta_max_rate 3000.0 # mm/min
  60. delta_acceleration 500.0 # mm/sec²
  61.  
  62. # B axis
  63. epsilon_steps_per_mm 100 # may be steps per degree for example
  64. epsilon_step_pin xx # Pin for delta stepper step signal
  65. epsilon_dir_pin xx # Pin for delta stepper direction
  66. epsilon_en_pin xx # Pin for delta enable
  67. epsilon_current 1.5 # Z stepper motor current
  68. epsilon_max_rate 300.0 # mm/min
  69. epsilon_acceleration 500.0 # mm/sec²
  70.  
  71. # C axis
  72. zeta_steps_per_mm 100 # may be steps per degree for example
  73. zeta_step_pin xx # Pin for delta stepper step signal
  74. zeta_dir_pin xx # Pin for delta stepper direction
  75. zeta_en_pin xx # Pin for delta enable
  76. zeta_current 1.5 # Z stepper motor current
  77. zeta_max_rate 300.0 # mm/min
  78. zeta_acceleration 500.0 # mm/sec²
  79.  
  80. ## Extruder module configuration
  81. # See http://smoothieware.org/extruder
  82. extruder.hotend.enable false # Whether to activate the extruder module at all. All configuration is ignored if false
  83. extruder.hotend.steps_per_mm 140 # Steps per mm for extruder stepper
  84. extruder.hotend.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  85. extruder.hotend.acceleration 500 # Acceleration for the stepper motor mm/sec²
  86. extruder.hotend.max_speed 50 # Maximum speed in mm/s
  87.  
  88. extruder.hotend.step_pin 2.3 # Pin for extruder step signal
  89. extruder.hotend.dir_pin 0.22 # Pin for extruder dir signal ( add '!' to reverse direction )
  90. extruder.hotend.en_pin 0.21 # Pin for extruder enable signal
  91.  
  92. # Extruder offset
  93. #extruder.hotend.x_offset 0 # X offset from origin in mm
  94. #extruder.hotend.y_offset 0 # Y offset from origin in mm
  95. #extruder.hotend.z_offset 0 # Z offset from origin in mm
  96.  
  97. # Firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
  98. #extruder.hotend.retract_length 3 # Retract length in mm
  99. #extruder.hotend.retract_feedrate 45 # Retract feedrate in mm/sec
  100. #extruder.hotend.retract_recover_length 0 # Additional length for recover
  101. #extruder.hotend.retract_recover_feedrate 8 # Recover feedrate in mm/sec (should be less than retract feedrate)
  102. #extruder.hotend.retract_zlift_length 0 # Z-lift on retract in mm, 0 disables
  103. #extruder.hotend.retract_zlift_feedrate 6000 # Z-lift feedrate in mm/min (Note mm/min NOT mm/sec)
  104.  
  105. delta_current 1.5 # First extruder stepper motor current
  106.  
  107. # Second extruder module configuration
  108. #extruder.hotend2.enable false # Whether to activate the extruder module at all. All configuration is ignored if false
  109. #extruder.hotend2.steps_per_mm 140 # Steps per mm for extruder stepper
  110. #extruder.hotend2.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  111. #extruder.hotend2.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
  112. #extruder.hotend2.max_speed 50 # mm/s
  113.  
  114. #extruder.hotend2.step_pin 2.8 # Pin for extruder step signal
  115. #extruder.hotend2.dir_pin 2.13 # Pin for extruder dir signal ( add '!' to reverse direction )
  116. #extruder.hotend2.en_pin 4.29 # Pin for extruder enable signal
  117.  
  118. #extruder.hotend2.x_offset 0 # x offset from origin in mm
  119. #extruder.hotend2.y_offset 25.0 # y offset from origin in mm
  120. #extruder.hotend2.z_offset 0 # z offset from origin in mm
  121.  
  122. #epsilon_current 1.5 # Second extruder stepper motor current
  123.  
  124.  
  125. ## Laser module configuration
  126. # See http://smoothieware.org/laser
  127. laser_module_enable true # Whether to activate the laser module at all
  128. laser_module_pwm_pin 2.5 # This pin will be PWMed to control the laser.
  129. # Only pins 2.0, 2.1, 2.2, 2.3, 2.4, 2.5, 1.18, 1.20, 1.21, 1.23, 1.24, 1.26, 3.25 and 3.26
  130. # can be used since laser requires hardware PWM, see http://smoothieware.org/pinout
  131. #laser_module_ttl_pin 1.30 # This pin turns on when the laser turns on, and off when the laser turns off.
  132. laser_module_maximum_power .85 # This is the maximum duty cycle that will be applied to the laser
  133. laser_module_minimum_power 0.0 # This is a value just below the minimum duty cycle that keeps the laser
  134. # active without actually burning.
  135. laser_module_default_power 0.5 # This is the default laser power that will be used for cuts if a power has not been specified. The value is a scale between
  136. # the maximum and minimum power levels specified above
  137. laser_module_pwm_period 400 # This sets the pwm frequency as the period in microseconds
  138.  
  139. ## Temperature control configuration
  140. # See http://smoothieware.org/temperaturecontrol
  141.  
  142. # First hotend configuration
  143. temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all.
  144. temperature_control.hotend.thermistor_pin 0.23 # Pin for the thermistor to read
  145. temperature_control.hotend.heater_pin 2.7 # Pin that controls the heater, set to nc if a readonly thermistor is being defined
  146. temperature_control.hotend.thermistor EPCOS100K # See http://smoothieware.org/temperaturecontrol#toc5
  147. #temperature_control.hotend.beta 4066 # Or set the beta value
  148. temperature_control.hotend.set_m_code 104 # M-code to set the temperature for this module
  149. temperature_control.hotend.set_and_wait_m_code 109 # M-code to set-and-wait for this module
  150. temperature_control.hotend.designator T # Designator letter for this module
  151. #temperature_control.hotend.max_temp 300 # Set maximum temperature - Will prevent heating above 300 by default
  152. #temperature_control.hotend.min_temp 0 # Set minimum temperature - Will prevent heating below if set
  153.  
  154. # Safety control is enabled by default and can be overidden here, the values show the defaults
  155. # See http://smoothieware.org/temperaturecontrol#runaway
  156. #temperature_control.hotend.runaway_heating_timeout 900 # How long it can take to heat up, max is 2040 seconds.
  157. #temperature_control.hotend.runaway_cooling_timeout 0 # How long it can take to cool down if temp is set lower, max is 2040 seconds
  158. #temperature_control.hotend.runaway_range 20 # How far from the set temperature it can wander, max setting is 63°C
  159.  
  160. # PID configuration
  161. # See http://smoothieware.org/temperaturecontrol#pid
  162. #temperature_control.hotend.p_factor 13.7 # P ( proportional ) factor
  163. #temperature_control.hotend.i_factor 0.097 # I ( integral ) factor
  164. #temperature_control.hotend.d_factor 24 # D ( derivative ) factor
  165.  
  166. #temperature_control.hotend.max_pwm 64 # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
  167.  
  168. # Second hotend configuration
  169. #temperature_control.hotend2.enable true # Whether to activate this ( "hotend" ) module at all.
  170. #temperature_control.hotend2.thermistor_pin 0.25 # Pin for the thermistor to read
  171. #temperature_control.hotend2.heater_pin 1.23 # Pin that controls the heater
  172. #temperature_control.hotend2.thermistor EPCOS100K # See http://smoothieware.org/temperaturecontrol#thermistor
  173. ##temperature_control.hotend2.beta 4066 # or set the beta value
  174. #temperature_control.hotend2.set_m_code 104 # M-code to set the temperature for this module
  175. #temperature_control.hotend2.set_and_wait_m_code 109 # M-code to set-and-wait for this module
  176. #temperature_control.hotend2.designator T1 # Designator letter for this module
  177.  
  178. #temperature_control.hotend2.p_factor 13.7 # P ( proportional ) factor
  179. #temperature_control.hotend2.i_factor 0.097 # I ( integral ) factor
  180. #temperature_control.hotend2.d_factor 24 # D ( derivative ) factor
  181.  
  182. #temperature_control.hotend2.max_pwm 64 # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
  183.  
  184. temperature_control.bed.enable true # Whether to activate this ( "hotend" ) module at all.
  185. temperature_control.bed.thermistor_pin 0.24 # Pin for the thermistor to read
  186. temperature_control.bed.heater_pin 2.5 # Pin that controls the heater
  187. temperature_control.bed.thermistor Honeywell100K # See http://smoothieware.org/temperaturecontrol#thermistor
  188. #temperature_control.bed.beta 3974 # Or set the beta value
  189. temperature_control.bed.set_m_code 140 # M-code to set the temperature for this module
  190. temperature_control.bed.set_and_wait_m_code 190 # M-code to set-and-wait for this module
  191. temperature_control.bed.designator B # Designator letter for this module
  192.  
  193. # Bang-bang ( simplified ) control
  194. # See http://smoothieware.org/temperaturecontrol#bang-bang
  195. #temperature_control.bed.bang_bang false # Set to true to use bang bang control rather than PID
  196. #temperature_control.bed.hysteresis 2.0 # Set to the temperature in degrees C to use as hysteresis
  197.  
  198. ## Switch modules
  199. # See http://smoothieware.org/switch
  200.  
  201. # Switch module for fan control
  202. switch.fan.enable false # Enable this module
  203. switch.fan.input_on_command M106 # Command that will turn this switch on
  204. switch.fan.input_off_command M107 # Command that will turn this switch off
  205. switch.fan.output_pin 2.6 # Pin this module controls
  206. switch.fan.output_type pwm # PWM output settable with S parameter in the input_on_comand
  207. #switch.fan.max_pwm 255 # Set max pwm for the pin default is 255
  208.  
  209. #switch.misc.enable true # Enable this module
  210. #switch.misc.input_on_command M42 # Command that will turn this switch on
  211. #switch.misc.input_off_command M43 # Command that will turn this switch off
  212. #switch.misc.output_pin 2.4 # Pin this module controls
  213. #switch.misc.output_type digital # Digital means this is just an on or off pin
  214.  
  215. ## Temperatureswitch
  216. # See http://smoothieware.org/temperatureswitch
  217. # Automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
  218. # Useful to turn on a fan or water pump to cool the hotend
  219. #temperatureswitch.hotend.enable true #
  220. #temperatureswitch.hotend.designator T # first character of the temperature control designator to use as the temperature sensor to monitor
  221. #temperatureswitch.hotend.switch misc # select which switch to use, matches the name of the defined switch
  222. #temperatureswitch.hotend.threshold_temp 60.0 # temperature to turn on (if rising) or off the switch
  223. #temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals
  224. #temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals
  225.  
  226. ## Endstops
  227. # See http://smoothieware.org/endstops
  228. endstops_enable true # The endstop module is enabled by default and can be disabled here
  229. #corexy_homing false # Set to true if homing on a hbot or corexy
  230. alpha_min_endstop 1.24^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  231. alpha_max_endstop 1.25^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
  232. alpha_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  233. alpha_min 0 # This gets loaded as the current position after homing when home_to_min is set
  234. alpha_max 200 # This gets loaded as the current position after homing when home_to_max is set
  235. #beta_min_endstop 1.26^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  236. beta_max_endstop 1.26^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
  237. beta_homing_direction home_to_max # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  238. beta_min 0 # This gets loaded as the current position after homing when home_to_min is set
  239. beta_max 200 # This gets loaded as the current position after homing when home_to_max is set
  240. gamma_min_endstop 1.28^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  241. gamma_max_endstop 1.29^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
  242. gamma_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  243. gamma_min 0 # This gets loaded as the current position after homing when home_to_min is set
  244. gamma_max 200 # This gets loaded as the current position after homing when home_to_max is set
  245.  
  246. alpha_max_travel 500 # Max travel in mm for alpha/X axis when homing
  247. beta_max_travel 500 # Max travel in mm for beta/Y axis when homing
  248. gamma_max_travel 500 # Max travel in mm for gamma/Z axis when homing
  249.  
  250. # Optional enable limit switches, actions will stop if any enabled limit switch is triggered
  251. #alpha_limit_enable false # Set to true to enable X min and max limit switches
  252. #beta_limit_enable false # Set to true to enable Y min and max limit switches
  253. #gamma_limit_enable false # Set to true to enable Z min and max limit switches
  254.  
  255. # Endstops home at their fast feedrate first, then once the endstop is found they home again at their slow feedrate for accuracy
  256. alpha_fast_homing_rate_mm_s 50 # Alpha/X fast homing feedrate in mm/second
  257. alpha_slow_homing_rate_mm_s 25 # Alpha/X slow homing feedrate in mm/second
  258. beta_fast_homing_rate_mm_s 50 # Beta/Y fast homing feedrate in mm/second
  259. beta_slow_homing_rate_mm_s 25 # Beta/Y slow homing feedrate in mm/second
  260. gamma_fast_homing_rate_mm_s 4 # Gamma/Z fast homing feedrate in mm/second
  261. gamma_slow_homing_rate_mm_s 2 # Gamma/Z slow homing feedrate in mm/second
  262.  
  263. alpha_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for alpha/X
  264. beta_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for beta/Y
  265. gamma_homing_retract_mm 1 # Distance to retract from the endstop after it is hit for gamma/Z
  266.  
  267.  
  268. # Optional enable limit switches, actions will stop if any enabled limit switch is triggered (all are set for delta)
  269. #alpha_limit_enable false # Set to true to enable X min and max limit switches
  270. #beta_limit_enable false # Set to true to enable Y min and max limit switches
  271. #gamma_limit_enable false # Set to true to enable Z min and max limit switches
  272.  
  273. # Optional order in which axis will home, default is they all home at the same time,
  274. # If this is set it will force each axis to home one at a time in the specified order
  275. #homing_order XYZ # X axis followed by Y then Z last
  276. #move_to_origin_after_home false # Move XY to 0,0 after homing
  277. #endstop_debounce_count 100 # Uncomment if you get noise on your endstops, default is 100
  278. #endstop_debounce_ms 1 # Uncomment if you get noise on your endstops, default is 1 millisecond debounce
  279. #home_z_first true # Uncomment and set to true to home the Z first, otherwise Z homes after XY
  280.  
  281. # End of endstop config
  282. # Delete the above endstop section and uncomment next line and copy and edit Snippets/abc-endstop.config file to enable endstops for ABC axis
  283. #include abc-endstop.config
  284.  
  285. ## Z-probe
  286. # See http://smoothieware.org/zprobe
  287. zprobe.enable false # Set to true to enable a zprobe
  288. zprobe.probe_pin 1.28!^ # Pin probe is attached to, if NC remove the !
  289. zprobe.slow_feedrate 5 # Mm/sec probe feed rate
  290. #zprobe.debounce_count 100 # Set if noisy
  291. zprobe.fast_feedrate 100 # Move feedrate mm/sec
  292. zprobe.probe_height 5 # How much above bed to start probe
  293. #gamma_min_endstop nc # Normally 1.28. Change to nc to prevent conflict,
  294.  
  295. # Levelling strategy
  296. # Example for 3-point levelling strategy, see wiki documentation for other strategies
  297. #leveling-strategy.three-point-leveling.enable true # a leveling strategy that probes three points to define a plane and keeps the Z parallel to that plane
  298. #leveling-strategy.three-point-leveling.point1 100.0,0.0 # the first probe point (x,y) optional may be defined with M557
  299. #leveling-strategy.three-point-leveling.point2 200.0,200.0 # the second probe point (x,y)
  300. #leveling-strategy.three-point-leveling.point3 0.0,200.0 # the third probe point (x,y)
  301. #leveling-strategy.three-point-leveling.home_first true # home the XY axis before probing
  302. #leveling-strategy.three-point-leveling.tolerance 0.03 # the probe tolerance in mm, anything less that this will be ignored, default is 0.03mm
  303. #leveling-strategy.three-point-leveling.probe_offsets 0,0,0 # the probe offsets from nozzle, must be x,y,z, default is no offset
  304. #leveling-strategy.three-point-leveling.save_plane false # set to true to allow the bed plane to be saved with M500 default is false
  305.  
  306. ## Panel
  307. # See http://smoothieware.org/panel
  308. # Please find your panel on the wiki and copy/paste the right configuration here
  309. panel.enable true # Set to true to enable the panel code
  310.  
  311. # Example for reprap discount GLCD
  312. # on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
  313. # +5v is EXP1 pin 10, Gnd is EXP1 pin 9
  314. panel.lcd reprap_discount_glcd #
  315. panel.spi_channel 0 # SPI channel to use ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
  316. panel.spi_cs_pin 0.16 # SPI chip select ; GLCD EXP1 Pin 4
  317. panel.encoder_a_pin 3.25!^ # Encoder pin ; GLCD EXP2 Pin 3
  318. panel.encoder_b_pin 3.26!^ # Encoder pin ; GLCD EXP2 Pin 5
  319. panel.click_button_pin 1.30!^ # Click button ; GLCD EXP1 Pin 2
  320. panel.buzz_pin 0.27o # Pin for buzzer ; GLCD EXP1 Pin 1
  321. panel.back_button_pin 2.11!^ # Back button ; GLCD EXP2 Pin 8
  322.  
  323. panel.menu_offset 0 # Some panels will need 1 here
  324.  
  325. panel.alpha_jog_feedrate 6000 # X jogging feedrate in mm/min
  326. panel.beta_jog_feedrate 6000 # Y jogging feedrate in mm/min
  327. panel.gamma_jog_feedrate 200 # Z jogging feedrate in mm/min
  328.  
  329. panel.hotend_temperature 185 # Temp to set hotend when preheat is selected
  330. panel.bed_temperature 60 # Temp to set bed when preheat is selected
  331.  
  332. ## Custom menus : Example of a custom menu entry, which will show up in the Custom entry.
  333. # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
  334. custom_menu.power_on.enable true #
  335. custom_menu.power_on.name Power_on #
  336. custom_menu.power_on.command M80 #
  337.  
  338. custom_menu.power_off.enable true #
  339. custom_menu.power_off.name Power_off #
  340. custom_menu.power_off.command M81 #
  341.  
  342.  
  343. ## Network settings
  344. # See http://smoothieware.org/network
  345. network.enable false # Enable the ethernet network services
  346. network.webserver.enable true # Enable the webserver
  347. network.telnet.enable true # Enable the telnet server
  348. network.ip_address auto # Use dhcp to get ip address
  349. # Uncomment the 3 below to manually setup ip address
  350. #network.ip_address 192.168.3.222 # The IP address
  351. #network.ip_mask 255.255.255.0 # The ip mask
  352. #network.ip_gateway 192.168.3.1 # The gateway address
  353. #network.mac_override xx.xx.xx.xx.xx.xx # Override the mac address, only do this if you have a conflict
  354.  
  355. ## System configuration
  356. # Serial communications configuration ( baud rate defaults to 9600 if undefined )
  357. # For communication over the UART port, *not* the USB/Serial port
  358. uart0.baud_rate 115200 # Baud rate for the default hardware ( UART ) serial port
  359.  
  360. second_usb_serial_enable false # This enables a second USB serial port
  361. #leds_disable true # Disable using leds after config loaded
  362. #play_led_disable true # Disable the play led
  363.  
  364. # Kill button maybe assigned to a different pin, set to the onboard pin by default
  365. # See http://smoothieware.org/killbutton
  366. kill_button_enable true # Set to true to enable a kill button
  367. kill_button_pin 2.12 # Kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
  368.  
  369. #msd_disable false # Disable the MSD (USB SDCARD), see http://smoothieware.org/troubleshooting#disable-msd
  370. #dfu_enable false # For linux developers, set to true to enable DFU
  371.  
  372. # Only needed on a smoothieboard
  373. # See http://smoothieware.org/currentcontrol
  374. currentcontrol_module_enable true # Control stepper motor current via the configuration file
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!