API tools faq
paste
gioreva

Untitled

gioreva
Nov 9th, 2020
128
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 34.07 KB | None | 0 0
raw download clone embed print report
  1.  
  2.  
  3. U-Boot 1.1.3 (Nov 5 2020 - 12:05:10)
  4.  
  5. Board: MediaTek APSoC DRAM: 32 MB
  6. enable ephy clock...done. SSC disabled.
  7. MediaTek SPI flash driver, SPI clock: 46MHz
  8. spi device id: ef 40 18 0 0 (40180000)
  9. find flash: W25Q128FV
  10. *** Warning - bad CRC, using default environment
  11.  
  12. ============================================
  13. MediaTek U-Boot Version: 5.0.1.0-6
  14. --------------------------------------------
  15. ASIC 7620_MP (Port5<->None)
  16. DRAM component: 256 Mbits DDR, width 16
  17. DRAM bus: 16 bit
  18. Total memory: 32 MBytes
  19. Flash component: SPI Flash
  20. Date:Nov 5 2020 Time:12:05:10
  21. ============================================
  22. icache: sets:512, ways:4, linesz:32, total:65536
  23. dcache: sets:256, ways:4, linesz:32, total:32768
  24.  
  25. #### The CPU freq = 560 MHZ ####
  26. estimate memory size = 32 Mbytes
  27.  
  28. Please choose the operation:
  29. 1: Load system code to SDRAM via TFTP.
  30. 2: Load system code then write to Flash via TFTP.
  31. 3: Boot system code via Flash (default).
  32. 4: Enter boot command line interface.
  33. 5: Load system code then write to Flash via USB Storage.
  34. 9: Load U-Boot code then write to Flash via TFTP.
  35. 0
  36.  
  37.  
  38. 3: System Boot system code via Flash.
  39. ## Checking image at bc050000 ...
  40. Image Name: MIPS OpenWrt Linux-4.14.180
  41. Image Type: MIPS Linux Kernel Image (lzma compressed)
  42. Data Size: 1565112 Bytes = 1.5 MB
  43. Load Address: 80000000
  44. Entry Point: 80000000
  45. Verifying Checksum ... Bad Data CRC
  46.  
  47. ## Enter to Rescue Mode (image error) ##
  48.  
  49. NetTxPacket = 0x81FB5980
  50.  
  51. KSEG1ADDR(NetTxPacket) = 0xA1FB5980
  52.  
  53. NetLoopHttpd,call eth_halt !
  54. Trying eth2
  55.  
  56. ETH_STATE_ACTIVE!!
  57. HTTP server is starting at IP: 10.10.10.1
  58. HTTP server is ready!
  59.  
  60. Request for: /
  61. Request for: /style.css
  62. Data will be downloaded at 0x80200000 in RAM
  63. Upgrade type: firmware
  64. Upload file size: 4194542 bytes
  65. Loading: #######################################
  66. #######################################
  67. #######################################
  68. #######################################
  69. #######################################
  70. #######################################
  71. #######################################
  72. #######################################
  73. #######################################
  74. #######################################
  75. #######################################
  76. #######################################
  77. #######################################
  78. #######################################
  79. #######################################
  80. #######################################
  81. #######################################
  82. #######################################
  83. #######################################
  84. #######################################
  85. #######################################
  86. #######################################
  87. #######################################
  88. #######################################
  89. #######################################
  90. #######################################
  91. #######################################
  92. #######################################
  93. #######################################
  94. #######################################
  95. #######################################
  96. #######################################
  97. #######################################
  98. #######################################
  99. #######################################
  100. #######################################
  101. #######################################
  102. #######################################
  103. #######################################
  104. #######################################
  105. #######################################
  106. #######################################
  107. #######################################
  108. #######################################
  109. #######################################
  110. #######################################
  111. #######################################
  112. #######################################
  113. #######################################
  114. #######################################
  115. #######################################
  116. #######################################
  117. #######################################
  118. #######################################
  119. #######################################
  120. #######################################
  121. #######################################
  122. #######################################
  123. #######################################
  124. #######################################
  125. #######################################
  126. #######################################
  127. #######################################
  128. #######################################
  129. #######################################
  130. #######################################
  131. #######################################
  132. #######################################
  133. #######################################
  134. #######################################
  135. #######################################
  136. #######################################
  137. #######################################
  138. #######################################
  139. #################
  140.  
  141. HTTP upload is done! Upgrading...
  142.  
  143.  
  144. ****************************
  145. * FIRMWARE UPGRADING *
  146. * DO NOT POWER OFF DEVICE! *
  147. ****************************
  148.  
  149. ................................................................
  150. ................................................................
  151. .
  152. .
  153. Done!
  154. HTTP ugrade is done! Rebooting...
  155.  
  156.  
  157.  
  158. U-Boot 1.1.3 (Nov 5 2020 - 12:05:10)
  159.  
  160. Board: MediaTek APSoC DRAM: 32 MB
  161. enable ephy clock...done. SSC disabled.
  162. ******************************
  163. Software System Reset Occurred
  164. ******************************
  165. MediaTek SPI flash driver, SPI clock: 46MHz
  166. spi device id: ef 40 18 0 0 (40180000)
  167. find flash: W25Q128FV
  168. *** Warning - bad CRC, using default environment
  169.  
  170. ============================================
  171. MediaTek U-Boot Version: 5.0.1.0-6
  172. --------------------------------------------
  173. ASIC 7620_MP (Port5<->None)
  174. DRAM component: 256 Mbits DDR, width 16
  175. DRAM bus: 16 bit
  176. Total memory: 32 MBytes
  177. Flash component: SPI Flash
  178. Date:Nov 5 2020 Time:12:05:10
  179. ============================================
  180. icache: sets:512, ways:4, linesz:32, total:65536
  181. dcache: sets:256, ways:4, linesz:32, total:32768
  182.  
  183. #### The CPU freq = 560 MHZ ####
  184. estimate memory size = 32 Mbytes
  185.  
  186. Please choose the operation:
  187. 1: Load system code to SDRAM via TFTP.
  188. 2: Load system code then write to Flash via TFTP.
  189. 3: Boot system code via Flash (default).
  190. 4: Enter boot command line interface.
  191. 5: Load system code then write to Flash via USB Storage.
  192. 9: Load U-Boot code then write to Flash via TFTP.
  193. 0
  194.  
  195.  
  196. 3: System Boot system code via Flash.
  197. ## Checking image at bc050000 ...
  198. Image Name: MIPS OpenWrt Linux-4.14.180
  199. Image Type: MIPS Linux Kernel Image (lzma compressed)
  200. Data Size: 1565112 Bytes = 1.5 MB
  201. Load Address: 80000000
  202. Entry Point: 80000000
  203. Verifying Checksum ... OK
  204. Uncompressing Kernel Image ... OK
  205. No initrd
  206. ## Transferring control to Linux (at address 80000000) ...
  207. ## Giving linux memsize in MB, 32
  208.  
  209. Starting kernel ...
  210.  
  211. [ 0.000000] Linux version 4.14.180 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11063-85e04e9f46)) #0 Sat May 16 18:32:20 2020
  212. [ 0.000000] Board has DDR2
  213. [ 0.000000] Analog PMU set to hw control
  214. [ 0.000000] Digital PMU set to hw control
  215. [ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
  216. [ 0.000000] bootconsole [early0] enabled
  217. [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
  218. [ 0.000000] MIPS: machine is Noname Board
  219. [ 0.000000] Determined physical RAM map:
  220. [ 0.000000] memory: 02000000 @ 00000000 (usable)
  221. [ 0.000000] Initrd not found or empty - disabling initrd
  222. [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  223. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  224. [ 0.000000] Zone ranges:
  225. [ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
  226. [ 0.000000] Movable zone start for each node
  227. [ 0.000000] Early memory node ranges
  228. [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
  229. [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
  230. [ 0.000000] random: get_random_bytes called from 0x80481740 with crng_init=0
  231. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 8128
  232. [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
  233. [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
  234. [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
  235. [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
  236. [ 0.000000] Writing ErrCtl register=00036331
  237. [ 0.000000] Readback ErrCtl register=00036331
  238. [ 0.000000] Memory: 26320K/32768K available (3916K kernel code, 187K rwdata, 500K rodata, 1212K init, 215K bss, 6448K reserved, 0K cma-reserved)
  239. [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  240. [ 0.000000] NR_IRQS: 256
  241. [ 0.000000] CPU Clock: 560MHz
  242. [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
  243. [ 0.000000] systick: enable autosleep mode
  244. [ 0.000000] systick: running - mult: 214748, shift: 32
  245. [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6825930166 ns
  246. [ 0.000012] sched_clock: 32 bits at 280MHz, resolution 3ns, wraps every 7669584382ns
  247. [ 0.007599] Calibrating delay loop... 371.09 BogoMIPS (lpj=1855488)
  248. [ 0.073521] pid_max: default: 32768 minimum: 301
  249. [ 0.078252] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  250. [ 0.084640] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  251. [ 0.097778] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  252. [ 0.107331] futex hash table entries: 256 (order: -1, 3072 bytes)
  253. [ 0.113310] pinctrl core: initialized pinctrl subsystem
  254. [ 0.119670] NET: Registered protocol family 16
  255. [ 0.146177] rt2880_gpio 10000600.gpio: registering 24 gpios
  256. [ 0.151635] rt2880_gpio 10000600.gpio: registering 24 irq handlers
  257. [ 0.157958] rt2880_gpio 10000688.gpio: registering 1 gpios
  258. [ 0.163300] rt2880_gpio 10000688.gpio: registering 1 irq handlers
  259. [ 0.173762] clocksource: Switched to clocksource systick
  260. [ 0.180078] NET: Registered protocol family 2
  261. [ 0.185348] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
  262. [ 0.192075] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  263. [ 0.198308] TCP: Hash tables configured (established 1024 bind 1024)
  264. [ 0.204594] UDP hash table entries: 256 (order: 0, 4096 bytes)
  265. [ 0.210223] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  266. [ 0.216631] NET: Registered protocol family 1
  267. [ 0.223556] rt-timer 10000100.timer: maximum frequency is 1220Hz
  268. [ 0.230290] Crashlog allocated RAM at address 0x1f00000
  269. [ 0.237113] workingset: timestamp_bits=30 max_order=13 bucket_order=0
  270. [ 0.249405] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  271. [ 0.255056] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  272. [ 0.275180] io scheduler noop registered
  273. [ 0.278928] io scheduler deadline registered (default)
  274. [ 0.284884] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
  275. [ 0.293994] console [ttyS0] disabled
  276. [ 0.297445] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
  277. [ 0.307100] console [ttyS0] enabled
  278. [ 0.307100] console [ttyS0] enabled
  279. [ 0.314136] bootconsole [early0] disabled
  280. [ 0.314136] bootconsole [early0] disabled
  281. [ 0.330307] spi spi0.0: force spi mode3
  282. [ 0.344085] m25p80 spi0.0: w25q128 (16384 Kbytes)
  283. [ 0.348941] 4 fixed-partitions partitions found on MTD device spi0.0
  284. [ 0.355450] Creating 4 MTD partitions on "spi0.0":
  285. [ 0.360355] 0x000000000000-0x000000030000 : "u-boot"
  286. [ 0.366384] 0x000000030000-0x000000040000 : "u-boot-env"
  287. [ 0.372700] 0x000000040000-0x000000050000 : "factory"
  288. [ 0.378822] 0x000000050000-0x000001000000 : "firmware"
  289. [ 0.387918] 2 uimage-fw partitions found on MTD device firmware
  290. [ 0.394038] Creating 2 MTD partitions on "firmware":
  291. [ 0.399118] 0x000000000000-0x00000017e1f8 : "kernel"
  292. [ 0.405127] 0x00000017e1f8-0x000000fb0000 : "rootfs"
  293. [ 0.411011] mtd: device 5 (rootfs) set to be root filesystem
  294. [ 0.418420] 1 squashfs-split partitions found on MTD device rootfs
  295. [ 0.424808] 0x0000003da000-0x000000fb0000 : "rootfs_data"
  296. [ 0.432070] libphy: Fixed MDIO Bus: probed
  297. [ 0.445133] gsw: setting port4 to ephy mode
  298. [ 0.449455] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 4 link up (100Mbps/Full duplex)
  299. [ 0.458922] mtk_soc_eth 10100000.ethernet: generated random MAC address 5e:6c:4e:e3:62:15
  300. [ 0.467390] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
  301. [ 0.474199] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
  302. [ 0.483151] rt2880_wdt 10000120.watchdog: Initialized
  303. [ 0.489756] NET: Registered protocol family 10
  304. [ 0.498491] Segment Routing with IPv6
  305. [ 0.502350] NET: Registered protocol family 17
  306. [ 0.507022] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
  307. [ 0.520267] 8021q: 802.1Q VLAN Support v1.8
  308. [ 0.542645] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
  309. [ 0.556571] Freeing unused kernel memory: 1212K
  310. [ 0.561195] This architecture does not have kernel memory protection.
  311. [ 2.284418] init: Console is alive
  312. [ 2.288141] init: - watchdog -
  313. [ 2.448513] random: fast init done
  314. [ 4.174067] kmodloader: loading kernel modules from /etc/modules-boot.d/*
  315. [ 4.270892] usbcore: registered new interface driver usbfs
  316. [ 4.276659] usbcore: registered new interface driver hub
  317. [ 4.282210] usbcore: registered new device driver usb
  318. [ 4.293565] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  319. [ 4.302044] ehci-platform: EHCI generic platform driver
  320. [ 4.317766] phy phy-usbphy.0: remote usb device wakeup disabled
  321. [ 4.323833] phy phy-usbphy.0: UTMI 16bit 30MHz
  322. [ 4.328388] ehci-platform 101c0000.ehci: EHCI Host Controller
  323. [ 4.334313] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
  324. [ 4.342525] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
  325. [ 4.357541] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
  326. [ 4.364992] hub 1-0:1.0: USB hub found
  327. [ 4.369300] hub 1-0:1.0: 1 port detected
  328. [ 4.376625] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  329. [ 4.384607] ohci-platform: OHCI generic platform driver
  330. [ 4.390322] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
  331. [ 4.397290] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
  332. [ 4.405530] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
  333. [ 4.439336] hub 2-0:1.0: USB hub found
  334. [ 4.443637] hub 2-0:1.0: 1 port detected
  335. [ 4.451767] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
  336. [ 4.463389] init: - preinit -
  337. [ 6.124290] 8021q: adding VLAN 0 to HW filter on device eth0
  338. [ 6.145588] random: procd: uninitialized urandom read (4 bytes read)
  339. Press the [f] key and hit [enter] to enter failsafe mode
  340. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  341. [ 7.452834] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
  342. [ 7.490184] urandom-seed: Seed file not found (/etc/urandom.seed)
  343. [ 7.615414] procd: - early -
  344. [ 7.619369] procd: - watchdog -
  345. [ 8.086109] procd: - watchdog -
  346. [ 8.089743] procd: - ubus -
  347. [ 8.434519] random: ubusd: uninitialized urandom read (4 bytes read)
  348. [ 8.520566] random: ubusd: uninitialized urandom read (4 bytes read)
  349. [ 8.527724] random: ubusd: uninitialized urandom read (4 bytes read)
  350. [ 8.535378] procd: - init -
  351. Please press Enter to activate this console.
  352. [ 9.552760] kmodloader: loading kernel modules from /etc/modules.d/*
  353. [ 9.734243] ip6_tables: (C) 2000-2006 Netfilter Core Team
  354. [ 9.762652] Loading modules backported from Linux version v4.19.120-0-gfdc072324f3c
  355. [ 9.770547] Backport generated by backports.git v4.19.120-1-0-g60c3a249
  356. [ 9.800275] ip_tables: (C) 2000-2006 Netfilter Core Team
  357. [ 9.826497] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
  358. [ 9.962727] xt_time: kernel timezone is -0000
  359. [ 10.080522] PPP generic driver version 2.4.2
  360. [ 10.090960] urngd: jent-rng init failed, err: 2
  361. [ 10.097497] NET: Registered protocol family 24
  362. [ 10.130643] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
  363. [ 10.141758] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
  364. [ 10.149774] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
  365. [ 10.177864] kmodloader: done loading kernel modules from /etc/modules.d/*
  366. [ 42.454037] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
  367. [ 42.467652] jffs2_build_filesystem(): unlocking the mtd device...
  368. [ 42.471411] done.
  369. [ 42.479694] jffs2_build_filesystem(): erasing all blocks after the end marker...
  370. [ 42.898263] 8021q: adding VLAN 0 to HW filter on device eth0
  371. [ 42.960709] br-lan: port 1(eth0.2) entered blocking state
  372. [ 42.966304] br-lan: port 1(eth0.2) entered disabled state
  373. [ 42.972228] device eth0.2 entered promiscuous mode
  374. [ 42.977123] device eth0 entered promiscuous mode
  375. [ 43.068082] br-lan: port 1(eth0.2) entered blocking state
  376. [ 43.073673] br-lan: port 1(eth0.2) entered forwarding state
  377. [ 43.079596] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
  378. [ 43.941969] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  379. [ 50.693726] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration start
  380. [ 50.702463] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration end
  381. [ 54.984894] ieee80211 phy0: rt2800_loft_iq_calibration: Info - LOFT Calibration Done!
  382. [ 54.996763] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Start!
  383. [ 55.018056] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Done! CH = 0, (gain= 0, phase= 2)
  384. [ 55.028300] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Start!
  385. [ 55.049574] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Done! CH = 1, (gain= 1, phase=3f)
  386. [ 55.058940] ieee80211 phy0: rt2800_loft_iq_calibration: Info - TX IQ Calibration Done!
  387. [ 55.292127] ieee80211 phy0: rt2800_rxiq_calibration: Warning - RXIQ calibration FAIL
  388. [ 55.310276] ieee80211 phy0: rt2800_rxiq_calibration: Info - RXIQ G_imb=0, Ph_rx=1
  389. [ 55.385733] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
  390. [ 55.406593] br-lan: port 2(wlan0) entered blocking state
  391. [ 55.412109] br-lan: port 2(wlan0) entered disabled state
  392. [ 55.417935] device wlan0 entered promiscuous mode
  393. [ 55.472150] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
  394. [ 55.478863] br-lan: port 2(wlan0) entered blocking state
  395. [ 55.484362] br-lan: port 2(wlan0) entered forwarding state
  396.  
  397.  
  398. U-Boot 1.1.3 (Nov 5 2020 - 12:05:10)
  399.  
  400. Board: MediaTek APSoC DRAM: 32 MB
  401. enable ephy clock...done. SSC disabled.
  402. ***********************
  403. Watchdog Reset Occurred
  404. ***********************
  405. MediaTek SPI flash driver, SPI clock: 46MHz
  406. spi device id: ef 40 18 0 0 (40180000)
  407. find flash: W25Q128FV
  408. *** Warning - bad CRC, using default environment
  409.  
  410. ============================================
  411. MediaTek U-Boot Version: 5.0.1.0-6
  412. --------------------------------------------
  413. ASIC 7620_MP (Port5<->None)
  414. DRAM component: 256 Mbits DDR, width 16
  415. DRAM bus: 16 bit
  416. Total memory: 32 MBytes
  417. Flash component: SPI Flash
  418. Date:Nov 5 2020 Time:12:05:10
  419. ============================================
  420. icache: sets:512, ways:4, linesz:32, total:65536
  421. dcache: sets:256, ways:4, linesz:32, total:32768
  422.  
  423. #### The CPU freq = 560 MHZ ####
  424. estimate memory size = 32 Mbytes
  425.  
  426. Please choose the operation:
  427. 1: Load system code to SDRAM via TFTP.
  428. 2: Load system code then write to Flash via TFTP.
  429. 3: Boot system code via Flash (default).
  430. 4: Enter boot command line interface.
  431. 5: Load system code then write to Flash via USB Storage.
  432. 9: Load U-Boot code then write to Flash via TFTP.
  433. 0
  434.  
  435.  
  436. 3: System Boot system code via Flash.
  437. ## Checking image at bc050000 ...
  438. Image Name: MIPS OpenWrt Linux-4.14.180
  439. Image Type: MIPS Linux Kernel Image (lzma compressed)
  440. Data Size: 1565112 Bytes = 1.5 MB
  441. Load Address: 80000000
  442. Entry Point: 80000000
  443. Verifying Checksum ... OK
  444. Uncompressing Kernel Image ... OK
  445. No initrd
  446. ## Transferring control to Linux (at address 80000000) ...
  447. ## Giving linux memsize in MB, 32
  448.  
  449. Starting kernel ...
  450.  
  451. [ 0.000000] Linux version 4.14.180 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11063-85e04e9f46)) #0 Sat May 16 18:32:20 2020
  452. [ 0.000000] Board has DDR2
  453. [ 0.000000] Analog PMU set to hw control
  454. [ 0.000000] Digital PMU set to hw control
  455. [ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
  456. [ 0.000000] bootconsole [early0] enabled
  457. [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
  458. [ 0.000000] MIPS: machine is Noname Board
  459. [ 0.000000] Determined physical RAM map:
  460. [ 0.000000] memory: 02000000 @ 00000000 (usable)
  461. [ 0.000000] Initrd not found or empty - disabling initrd
  462. [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  463. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  464. [ 0.000000] Zone ranges:
  465. [ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
  466. [ 0.000000] Movable zone start for each node
  467. [ 0.000000] Early memory node ranges
  468. [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
  469. [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
  470. [ 0.000000] random: get_random_bytes called from 0x80481740 with crng_init=0
  471. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 8128
  472. [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
  473. [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
  474. [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
  475. [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
  476. [ 0.000000] Writing ErrCtl register=00036330
  477. [ 0.000000] Readback ErrCtl register=00036330
  478. [ 0.000000] Memory: 26320K/32768K available (3916K kernel code, 187K rwdata, 500K rodata, 1212K init, 215K bss, 6448K reserved, 0K cma-reserved)
  479. [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  480. [ 0.000000] NR_IRQS: 256
  481. [ 0.000000] CPU Clock: 560MHz
  482. [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
  483. [ 0.000000] systick: enable autosleep mode
  484. [ 0.000000] systick: running - mult: 214748, shift: 32
  485. [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6825930166 ns
  486. [ 0.000012] sched_clock: 32 bits at 280MHz, resolution 3ns, wraps every 7669584382ns
  487. [ 0.007598] Calibrating delay loop... 371.09 BogoMIPS (lpj=1855488)
  488. [ 0.073520] pid_max: default: 32768 minimum: 301
  489. [ 0.078251] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  490. [ 0.084639] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  491. [ 0.097777] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  492. [ 0.107330] futex hash table entries: 256 (order: -1, 3072 bytes)
  493. [ 0.113310] pinctrl core: initialized pinctrl subsystem
  494. [ 0.119669] NET: Registered protocol family 16
  495. [ 0.146174] rt2880_gpio 10000600.gpio: registering 24 gpios
  496. [ 0.151631] rt2880_gpio 10000600.gpio: registering 24 irq handlers
  497. [ 0.157954] rt2880_gpio 10000688.gpio: registering 1 gpios
  498. [ 0.163296] rt2880_gpio 10000688.gpio: registering 1 irq handlers
  499. [ 0.173759] clocksource: Switched to clocksource systick
  500. [ 0.180074] NET: Registered protocol family 2
  501. [ 0.185345] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
  502. [ 0.192072] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  503. [ 0.198304] TCP: Hash tables configured (established 1024 bind 1024)
  504. [ 0.204591] UDP hash table entries: 256 (order: 0, 4096 bytes)
  505. [ 0.210221] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  506. [ 0.216629] NET: Registered protocol family 1
  507. [ 0.223554] rt-timer 10000100.timer: maximum frequency is 1220Hz
  508. [ 0.230287] Crashlog allocated RAM at address 0x1f00000
  509. [ 0.237110] workingset: timestamp_bits=30 max_order=13 bucket_order=0
  510. [ 0.249401] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  511. [ 0.255052] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  512. [ 0.275175] io scheduler noop registered
  513. [ 0.278923] io scheduler deadline registered (default)
  514. [ 0.284879] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
  515. [ 0.293989] console [ttyS0] disabled
  516. [ 0.297439] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
  517. [ 0.307093] console [ttyS0] enabled
  518. [ 0.307093] console [ttyS0] enabled
  519. [ 0.314131] bootconsole [early0] disabled
  520. [ 0.314131] bootconsole [early0] disabled
  521. [ 0.330302] spi spi0.0: force spi mode3
  522. [ 0.344064] m25p80 spi0.0: w25q128 (16384 Kbytes)
  523. [ 0.348921] 4 fixed-partitions partitions found on MTD device spi0.0
  524. [ 0.355430] Creating 4 MTD partitions on "spi0.0":
  525. [ 0.360335] 0x000000000000-0x000000030000 : "u-boot"
  526. [ 0.366364] 0x000000030000-0x000000040000 : "u-boot-env"
  527. [ 0.372681] 0x000000040000-0x000000050000 : "factory"
  528. [ 0.378803] 0x000000050000-0x000001000000 : "firmware"
  529. [ 0.387899] 2 uimage-fw partitions found on MTD device firmware
  530. [ 0.394018] Creating 2 MTD partitions on "firmware":
  531. [ 0.399099] 0x000000000000-0x00000017e1f8 : "kernel"
  532. [ 0.405108] 0x00000017e1f8-0x000000fb0000 : "rootfs"
  533. [ 0.410992] mtd: device 5 (rootfs) set to be root filesystem
  534. [ 0.418402] 1 squashfs-split partitions found on MTD device rootfs
  535. [ 0.424790] 0x0000003da000-0x000000fb0000 : "rootfs_data"
  536. [ 0.432053] libphy: Fixed MDIO Bus: probed
  537. [ 0.445113] gsw: setting port4 to ephy mode
  538. [ 0.449433] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 4 link up (100Mbps/Full duplex)
  539. [ 0.458894] mtk_soc_eth 10100000.ethernet: generated random MAC address 8a:39:7b:75:30:0f
  540. [ 0.467361] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
  541. [ 0.474172] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
  542. [ 0.483124] rt2880_wdt 10000120.watchdog: Initialized
  543. [ 0.489729] NET: Registered protocol family 10
  544. [ 0.498469] Segment Routing with IPv6
  545. [ 0.502328] NET: Registered protocol family 17
  546. [ 0.507000] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
  547. [ 0.520245] 8021q: 802.1Q VLAN Support v1.8
  548. [ 0.542641] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
  549. [ 0.556566] Freeing unused kernel memory: 1212K
  550. [ 0.561190] This architecture does not have kernel memory protection.
  551. [ 2.284451] init: Console is alive
  552. [ 2.288172] init: - watchdog -
  553. [ 2.443723] random: fast init done
  554. [ 4.174173] kmodloader: loading kernel modules from /etc/modules-boot.d/*
  555. [ 4.271022] usbcore: registered new interface driver usbfs
  556. [ 4.276790] usbcore: registered new interface driver hub
  557. [ 4.282339] usbcore: registered new device driver usb
  558. [ 4.293786] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  559. [ 4.302200] ehci-platform: EHCI generic platform driver
  560. [ 4.317925] phy phy-usbphy.0: remote usb device wakeup disabled
  561. [ 4.323993] phy phy-usbphy.0: UTMI 16bit 30MHz
  562. [ 4.328548] ehci-platform 101c0000.ehci: EHCI Host Controller
  563. [ 4.334472] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
  564. [ 4.342688] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
  565. [ 4.357649] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
  566. [ 4.365103] hub 1-0:1.0: USB hub found
  567. [ 4.369410] hub 1-0:1.0: 1 port detected
  568. [ 4.376758] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  569. [ 4.384751] ohci-platform: OHCI generic platform driver
  570. [ 4.390459] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
  571. [ 4.397427] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
  572. [ 4.405667] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
  573. [ 4.439463] hub 2-0:1.0: USB hub found
  574. [ 4.443768] hub 2-0:1.0: 1 port detected
  575. [ 4.451908] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
  576. [ 4.463528] init: - preinit -
  577. strings: standard output: Broken pipe
  578. [ 6.125588] 8021q: adding VLAN 0 to HW filter on device eth0
  579. [ 6.146873] random: procd: uninitialized urandom read (4 bytes read)
  580. Press the [f] key and hit [enter] to enter failsafe mode
  581. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  582. [ 7.454698] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
  583. [ 7.492011] urandom-seed: Seed file not found (/etc/urandom.seed)
  584. [ 7.617788] procd: - early -
  585. [ 7.620854] procd: - watchdog -
  586. [ 8.087644] procd: - watchdog -
  587. [ 8.091213] procd: - ubus -
  588. [ 8.435442] random: ubusd: uninitialized urandom read (4 bytes read)
  589. [ 8.521486] random: ubusd: uninitialized urandom read (4 bytes read)
  590. [ 8.528638] random: ubusd: uninitialized urandom read (4 bytes read)
  591. [ 8.536228] procd: - init -
  592. Please press Enter to activate this console.
  593. [ 9.562679] kmodloader: loading kernel modules from /etc/modules.d/*
  594. [ 9.744101] ip6_tables: (C) 2000-2006 Netfilter Core Team
  595. [ 9.772445] Loading modules backported from Linux version v4.19.120-0-gfdc072324f3c
  596. [ 9.780342] Backport generated by backports.git v4.19.120-1-0-g60c3a249
  597. [ 9.810153] ip_tables: (C) 2000-2006 Netfilter Core Team
  598. [ 9.836408] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
  599. [ 9.969713] xt_time: kernel timezone is -0000
  600. [ 10.083253] PPP generic driver version 2.4.2
  601. [ 10.092836] urngd: jent-rng init failed, err: 2
  602. [ 10.098952] NET: Registered protocol family 24
  603. [ 10.132839] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
  604. [ 10.144029] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
  605. [ 10.152030] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
  606. [ 10.177793] kmodloader: done loading kernel modules from /etc/modules.d/*
  607. [ 35.814983] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
  608. [ 35.822926] jffs2_build_filesystem(): unlocking the mtd device...
  609. [ 35.839987] done.
  610. [ 35.848337] jffs2_build_filesystem(): erasing all blocks after the end marker...
  611. [ 36.273862] 8021q: adding VLAN 0 to HW filter on device eth0
  612. [ 36.343578] br-lan: port 1(eth0.2) entered blocking state
  613. [ 36.349193] br-lan: port 1(eth0.2) entered disabled state
  614. [ 36.355129] device eth0.2 entered promiscuous mode
  615. [ 36.360025] device eth0 entered promiscuous mode
  616. [ 36.453363] br-lan: port 1(eth0.2) entered blocking state
  617. [ 36.458952] br-lan: port 1(eth0.2) entered forwarding state
  618. [ 36.464876] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
  619. [ 37.305430] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  620. [ 43.937295] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration start
  621. [ 43.946037] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration end
  622. [ 48.234931] ieee80211 phy0: rt2800_loft_iq_calibration: Info - LOFT Calibration Done!
  623. [ 48.246716] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Start!
  624. [ 48.267998] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Done! CH = 0, (gain= 1, phase= 2)
  625. [ 48.278242] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Start!
  626. [ 48.299516] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Done! CH = 1, (gain= 0, phase= 2)
  627. [ 48.308881] ieee80211 phy0: rt2800_loft_iq_calibration: Info - TX IQ Calibration Done!
  628. [ 48.547183] ieee80211 phy0: rt2800_rxiq_calibration: Info - RXIQ G_imb=0, Ph_rx=3
  629. [ 48.557937] ieee80211 phy0: rt2800_rxiq_calibration: Warning - RXIQ calibration FAIL
  630. [ 48.621474] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
  631. [ 48.643191] br-lan: port 2(wlan0) entered blocking state
  632. [ 48.648723] br-lan: port 2(wlan0) entered disabled state
  633. [ 48.654546] device wlan0 entered promiscuous mode
  634. [ 48.707325] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
  635. [ 48.714037] br-lan: port 2(wlan0) entered blocking state
  636. [ 48.719537] br-lan: port 2(wlan0) entered forwarding state
  637. [ 102.674989] random: crng init done
  638. [ 102.678482] random: 6 urandom warning(s) missed due to ratelimiting
  639.  
  640.  
  641.  
  642.  
  643. BusyBox v1.30.1 () built-in shell (ash)
  644.  
  645. _______ ________ __
  646. | |.-----.-----.-----.| | | |.----.| |_
  647. | - || _ | -__| || | | || _|| _|
  648. |_______|| __|_____|__|__||________||__| |____|
  649. |__| W I R E L E S S F R E E D O M
  650. -----------------------------------------------------
  651. OpenWrt 19.07.3, r11063-85e04e9f46
  652. -----------------------------------------------------
  653. === WARNING! =====================================
  654. There is no root password defined on this device!
  655. Use the "passwd" command to set up a new password
  656. in order to prevent unauthorized SSH logins.
  657. --------------------------------------------------
  658. root@OpenWrt:/#
  659. root@OpenWrt:/# [ 204.741046] done.
  660. [ 204.743067] jffs2: notice: (1202) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
  661. [ 205.000350] overlayfs: upper fs does not support tmpfile.
  662.  
  663.  
Add Comment
Please, Sign In to add comment
Public Pastes
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!